during trap handlers.
Implement ptrace_set_pc FWIW.
Initialize the pcb window scratch area in setregs(), and setup user
registers as specified by the SCD.
Submitted by: tmm
kernel from usermode. The remaining user windows are spilled
to the pcb as necessary. The user land window fault handlers
fill directly from the pcb on return.
Add system call entry points.
Submitted by: tmm
has existed for a long time, but I made it worse a few months ago
by by adding calls to VFS_ROOT() and checkdirs() in revision 1.179.
Also, remove the LK_REENABLE flag in the lockmgr() call; this flag
has been ignored by the lockmgr code for 4 years. This was the only
remaining mention of it apart from its definition.
Reviewed by: jhb
that do not have valid NVRAM. In particular, we were leaving
a retry count set (to retry selection timeouts) when thats
not really what we want. Do some constant string additions
so that LOGDEBUG0 info is useful across all cards.
MFC after: 2 weeks
information. The default limits only effect machines with > 1GB of ram
and can be overriden with two new kernel conf variables VM_SWZONE_SIZE_MAX
and VM_BCACHE_SIZE_MAX, or with loader variables kern.maxswzone and
kern.maxbcache. This has the effect of leaving more KVM available for
sizing NMBCLUSTERS and 'maxusers' and should avoid tripups where a sysad
adds memory to a machine and then sees the kernel panic on boot due to
running out of KVM.
Also change the default swap-meta auto-sizing calculation to allocate half
of what it was previously allocating. The prior defaults were way too high.
Note that we cannot afford to run out of swap-meta structures so we still
stay somewhat conservative here.
the ISR. We keep track of the card state and don't call the IRS when
the card isn't inserted. This helps quite a bit with card ejection
problems that Ian was seeing.
Submitted by: Ian Dowse
MFC upon: re approvel.
this allows constants to be copied without giving errors.
(removes a couple of warning messages in the kernel.)
Note: uipc_mbuf.c is a forced commit as it was accidentally included in another commit.
MFC after: 2 weeks
`struct xucred` with the credentials of the connected peer.
Obviously this only works (and makes sense) on SOCK_STREAM
sockets. This works for both the connect(2) and listen(2)
callers.
There is precise documentation of the semantics in unix(4).
Reviewed by: dwmalone (eyeballed)
should be initialized to 0 for PCI adapters which was a side-effect of
the memset in ahc_alloc(). EISA/VL adapters require our unpause value to
include the "levelness" of our interrupt.
This change allows EISA adapters to work again.
PR: 29689, 29471
prevent/workaround TX lockups in this driver. The secret seems to be to
not let the TX DMA queue become too full. If we have too many packets
in the queue, we should wait for them to drain a bit before trying to
queue more. This should prevent the lockup from occurring, and if it
does occur, there is special code in sf_start() to kick the NIC in the
head and get it going again.
Special thanks to Glen Neff for helping me test this fix.
to properly clear the interrupt register on the no error case. Also,
set the mcr register to zero when we find we can't support the chip.
This fixes the hang on sio driver attach problem in the new pci pccard
code that some people have reported. At least on my machine. I'd
like to get this into 4.4.
Submitted by: bde
PR: kern/29742
MFC after: 1 day
unnecessary breakage.
While here, use explicit sizes for the string fields so that we dont
have unintentional changes again in the future when key tunables change.
This still is not quite right, but a june userland is happy with
a -current kernel with these tweaks.
probably harmless in this case, since the latter is called on tty
input, which is usually a result of some system call, so we've got
plenty of stack left. It's still nice to fix these things, though, in
case somebody ever decides this driver is a good example of something
(perhaps "what you probably shouldn't do").
night of testing before merging to -stable.
Also added to code to detect TX underruns and automatically increase the
TX threshold to avoid them. Carefully placed diagnostig printf() about
this under #ifdef DIAGNOSTIC to avoid getting any panicky e-mails from
confused users, like I always do with the xl and dc drivers.
calling vtophys() and contigmalloc()/contigfree() directly. Hopefully,
I have shaken out all of the problems with busdma on the alpha now.
(Everything seems to work as expected.)
Also, change the max RX DMA limit to 1024 bytes instead of "unlimited,"
as the latter seems not to work correctly on the alpha that I tested.
(At 100Mbps, all attempts to receive frames yield RX errors.)
but it's better than the buggy behavior we have now. If we contigmalloc()
buffers in bus_dmamem_alloc(), then we must configfree() them in
bus_dmamem_free(). Trying to free() them is wrong, and will cause
a panic (at least, it does on the alpha.)
I tripped over this when trying to kldunload my busdma-ified if_rl
driver.
label if the dump device overflaps the label (which is a slight
misconfiguration). Dump routines don't use dscheck(), so the normal
write protection of the label doesn't help.
Reduced some nearby overflow bugs. In disk_dumpcheck(), there was
(fatal but fail-safe) overflow on i386's with 4GB of memory, at least
if Maxmem was the top page (can this happen?). The fix assumes that
the sector size divides PAGE_SIZE (dump routines already assume this).
In setdumpdev(), the corresponding overflow occurred with only about
2GB of memory on all machines with 32-bit ints. This allowed setdumpdev()
to succeed when it shouldn't have, but then disk_dumpcheck() failed
safe later. Except in old versions of FreeBSD like RELENG_3 where
there is no disk_dumpcheck().
PR: 28164 (label clobbering part)
MFC after: 1 week
to see if it was malloc()ed first" bug. In bus_dmamap_create(), one of
two things can happen: either we need to allocate a special map due to
some manner of bounce buffering requirement, or we can DMA a buffer
in place. On the x86 platform, the "in place" case results in
bus_dmamap_create() returning a dmamap of NULL. The bus_dmamap_destroy()
routine later checks for NULL and won't bother free()ing the map if
it detects this condition.
But on the alpha, we don't use NULL, we use a statically allocated map
called nobounce_dmamap(). Unfortunately, bus_dmamap_destroy() does not
handle the condition where we attempt to destroy such a map: it tries
to free() the dmamap, which causes a panic.
Fix: test that map != &nobounce_dmamap before trying to free() it.
With this fix, my busdma-ified if_sis driver works on the alpha. I'm
a bit alarmed that I'm the first person ever to trip over this bug, since
we have been using busdma on the alpha for a while, and since it sort
of screams out "Hi! I'm a bug! Booga-booga!" when you look at it.
(Somewhere, somebody will say: "But Bill, why don't you just not bother
destroying the maps in this case." Because the API is supposed to be
a) symetrical and b) opaque to the caller. I can't know whether it's safe
to skip the bus_dmamap_destroy() step or not without sticking my fingers
into unsafe places, which is what I wanted to avoid in the first place.)
assing an IRQ. Add better comments while I'm here.
MFC after: 1 day
# Note: That's merging all the -current pci pcic code, not just this one
# change for the Aug 15th code freeze.
register. It enables Zoom Video. It appears that on at least one
card that Monzoon is using sets these bits by default. Nothing works
when these bits are set, everything works when they are clear.
Add commentary on some of the ti bits. Make code a little clearer.
Also remove a call to pcic_pci_pd6729 which was prematurely added in
the last commit.
linux_getdents uses VOP_READDIR( ..., &ncookies, &cookies ) instead of
VOP_READDIR( ..., NULL, NULL ) because it seems to need the offsets for
linux_dirent and sizeof(dirent) != sizeof(linux_dirent)...
PR: 29467
Submitted by: Michael Reifenberger <root@nihil.plaut.de>
Reviewed by: phk
