The mdio driver interface is generally useful for devices that require
MDIO without the full MII bus interface. This lifts the driver/interface
out of etherswitch(4), and adds a mdio(4) man page.
Submitted by: Landon Fuller <landon@landonf.org>
Differential Revision: https://reviews.freebsd.org/D4606
Add e6000sw driver supporting Marvell 88E6352, 88E6172, 88E6176 switches.
It needs to be attached to mdio interface, exporting SMI access
functionality. e6000sw supports port-based VLAN configuration, per-port
media changing, accessing PHY and switch registers.
e6000sw attaches miibuses and PHY drivers as children. Instead of typical
tick as callout, kthread-based tick is used. This combined with SX locks
allows MDIO read/write calls to sleep. It is expected, because this
hardware requires long delays in SMI read/write procedures, which can not
be handled by busy-waiting.
Reviewed by: adrian
Obtained from: Semihalf
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D3902
I messed up when doing the reset_vlans method - setting vid[0] = 1 here
was making it 'hidden' from configuration (as it needed ETHERSWITCH_VID_VALID
as well) and so there was no way to configure vlangroup0.
In per-port VLAN mode, vlangroup0 is for the CPU port (port0).
Now, it normally wouldn't really matter - the CPU port thus sees
all other ports. However there are two CPU ports on the AR8327 and
so port0 (arge0) was seeing all traffic on port6 (arge1).
If you thus tried to use arge1/port6 for anything (eg a WAN port)
in a bridge group then things would very upset very quickly.
Whilst here, add a comment to remind myself that yes, it'd be nice
if we could specify a boot-time switch config.
Tested:
* AP135 reference platform w/ AR8327N switch
This is slightly different to the other switches - the VLAN table
(VTU) programs in the vlan port mapping /and/ the port config
(tagged, untagged, passthrough, any.)
So:
* Add VTU operations to program the VTU (vlan table)
* abstract out the mirror-disable function so it's .. well, a function.
* setup the port to have a dot1q configuration for dot1q - the
port security is VLAN (not per-port VLAN) and requires an entry
in the VLAN table;
* add set_dot1q / get_dot1q to program the VLAN table;
* since the tagged/untagged ports are now programmed into the VTU,
rather than global - plumb the ports /and/ untagged ports bitmaps
through the arswitch API.
Tested:
* AP135 - QCA9558 SoC + AR8327N switch
All the per-port support is really doing is applying a port visibility
mask to each of the switchports. Everything still look like a single
portgroup (vlan id 1), but the per-port visibility mask is modified.
Whilst I'm here, also add some initial dot1q support - the pvid stuff
is doing the right thing, but it's not useful without the rest of
the VLAN table programming.
It's enough for me to be able to use the LAN/WAN port distinction
on the AP135, where there isn't (for now!) a dedicated PHY for the
"WAN" port.
Tested:
* AP135, QCA9558 SoC + AR8327 switch
* Even though I got the registers around "right", it seems
I'm not tickling the MDIO access correctly for the internal PHY
bus. Some of the switches are fine poking at the external PHY
registers; others aren't. So, enable direct PHY bus access
for the AR8327, and leave the existing code in place for the
others.
* Go and shuffle the register access around. Whilst here,
restore the 2ms delay if changing page.
* Comment out some of the stub printf()s; there's some upcoming
work to add port VLAN support.
Tested:
* AP135 development board
* Carambola2 - AR9331 SoC
I noticed that openwrt/linux does this, citing "instability", so
until they figure out why I'm going to disable it here as well.
Tested:
* QCA AP135 - QCA955x SoC + AR8327 switch.
So, it turns out that the AR8327 has 7 ports internally:
* GMAC0 / external (CPU) MAC0
* GMAC1 / port1 -> GMAC5 / port5: external switch port PHYs
* GMAC6 / external (CPU) MAC1
Now, depending upon how things are wired up, the second CPU port (MAC1)
can be wired to either the switch (port6), or through port5's PHY, bypassing
the GMAC+switch entirely. Ie, it can pretend to be a boring PHY, saving
system designers from having to include a separate PHY for a "WAN" port.
Here's the rub - the AP135 board (QCA955x SoC) hooks up arge0 to
the second CPU port on the AR8327, but it's hooked up as RGMII.
So, in order to hook it up to the rest of the switch, it isn't configured
as a separate PHY - OpenWRT has it setup as connected via RGMII to
GMAC6 and (I'm guessing) it's set to be a WAN port by configuring up
port-based VLANs or something.
Thus, with a port mask of 0x3f, GMAC6 was never allowed to receive traffic
from any other port. It could transmit fine, but not receive anything.
So, now it works enough for me to continue doing board bootstrapping.
Note, this isn't enough to make the QCA955x + AR8327 work - there's
a bunch of uncommitted work to both the platform SoC (interrupt handling,
ethernet, etc) and the ethernet switch (register access space, setup, etc)
that needs to happen. However, this particular change is also relevant to
other SoCs, like the AR934x and AR7161, both of which can be glued to
this switch.
Tested:
* AP135 development board
TODO:
* Figure out whether I can somehow abuse another port mode to have this
be a pass-through PHY, or whether I should just create some more boot
time hints to explicitly set up port-based isolation so this works
in a more useful way by default.
Update some comments on code, specifying the correct vlans used on switch
setup.
Advertise the proper switch operation mode (the rtl8366rb only support
dot1q vlans).
This fixes the breakage that i introduced on r249752 and make the rtl8366rb
switch works again with etherswitchcfg(8).
Tested on TP-Link 1043ND.
Tested by: me, Harm Weites (harm at weites.com)
(pvid=1) and we already configure them to send to other ports.
Setting pvid=portnum would mean that there were separate vlangroups
for each ports, but 'leaking' into other ports. The result? All port
traffic flooded to all other port traffic.
Tested:
* DB120, AR9344 + AR8327 switch
The OpenWRT AR8xxx switch support flushes the ATU (address translation
unit) after each port link 'up' status change. I've modified this to
just flush on any port transition.
Whilst here, bump the number of ports on the AR8327 to 6, rather than
the default of 5. It's DB120 specific; I'll go and make this configurable
later.
There's some debugging code in here still; I am still debugging whether
this is or isn't working fully.
Tested:
* DB120, AR9344 + AR8327 switch
Obtained from: OpenWRT
This patch does four things:
* it globally disables mirroring;
* it globally sets the mirroring on each port to be disabled;
* the initial port setup now programs a portmask for the port to allow
transmission (forwarding) to all other ports bar itself;
* the vlan setup path now programs the portmask for the port to
allow transmission (forwarding) to all other ports bar itself.
Before this, I hard-coded the portmask to 0x3f which would mean all
ports (bar port 6, which currently isn't hooked up to anything.)
This means that traffic would be duplicated back out the port it
received it. I bet this wasn't .. optimal.
In any case, this _seems_ to make DHCP from my macosx laptop
work through this access point. I'll do some further testing
to ensure it's actually working correctly on all my devices.
Tested:
* DB120, AR8327 switch
It's still hardcoded (for db120) but it is now hardcoded in all the
same place (ie, the pdata path.) The port config/status code now checks
port0/port6 as appropriate to configure things.
Tested:
* Qualcomm Atheros DB120, AR8327 switch.
This is (almost!) enough to actually probe, attach, configure a default
port group and do some basic work. It's also totally hard-coded for
the Qualcomm Atheros DB120 board - it doesn't yet have any of the code
from OpenWRT which parses extra configuration data to know how to program
the switch. The LED stuff is also missing.
But, it's enough to facilitate board, PHY, switch and VLAN bringup,
so I am committing it now.
Tested:
* Qualcomm Atheros DB120
Obtained from: OpenWRT
switches.
* Add some new VLAN HAL methods that will be used by the VLAN configuration
code. The AR933x and later switches use slightly different register
layouts (even though the driver currently doesn't support it.)
HAL methods.
This allows the AR8327 code to override it as appropriate.
Tested:
* DB120 - AR8327 and AR9340 on-board switch; only running 'etherswitchcfg'
to check configs. The actual VLAN programming wasn't tested.
The registers (and perhaps the flags) are different for the AR8327, so
I'll stub those out until they're written.
Tested:
* DB120 - both on-chip AR9340 and AR8327 switches.
a single port to setup.
This may end up later being used as part of some logic to program
the PHY for a single port, rather than having to reinitialise them
all at once.
Tested:
* DB120
