patch the RX/TX performance becomes about 17~18 Mbps comparing with
the previous whose values were RX 7~8Mbps and TX 13~14Mbps.
- improve AL2230 RF handling in zd1211b
- support AL2230S RF that PV2000 is renamed to AL2230S
- use register ZYD_CR244, ZYD_CR243, ZYD_CR242 when the driver writes
values on RF. This routine is more faster than the original one
- use private TX lock to avoid LOR at zyd_raw_xmit()
- increase TX slots from 1 to 5
- needs to set the channel at IEEE80211_S_AUTH not IEEE80211_S_RUN
- detailed error handling. In previous the next command was sent to the
device even if there was errors
- setting ZYD_MAC_RX_THRESHOLD value should be different between 1211
and 1211b
- only try to stop the device at zyd_init_locked() if the device is
UPed
- do not use MTX_RECURSE
- do not try to grap Giant lock when the channel is changing
- move the device initialization routines from zyd_attach to zyd_init to
give a device full-reset chance to the driver.
- code cleanup at zyd_raw_xmit()
- simplify zyd_attach() routines
- resort functions and clean up variables
- DPRINTF style change.
- style(9)
Reviewed by: sam
check to fxp_txeof(). While I'm here unarm watchdog timer only if
there are no pending queued Tx requests.
Previously the watchdog timer was unarmed whenever Tx interrupt is
raised. This could be resulted in hiding root cause of watchdog
timeouts.
checksum offload configuration. Now checksum offload can be
controlled by ifconfig(8).
While I'm here add an additional check for interface capabilities
before applying user's request.
nodes capabilities. Add "Analog"/"Digital" marks to the pcm device names.
I hope it will help new users easier accept concept of several PCM devices
and understand exact purposes of that devices.
- invert sense of hw.cxgb.singleq tunable to hw.cxgb.multiq
- don't wake up transmitting thread by default
- add per tx queue ifaltq to handle ALTQ
- remove several unused functions in cxgb_multiq.c
- add several sysctls: multiq_tx_enable, coalesce_tx_enable,
and wakeup_tx_thread
- this obsoletes the hw.cxgb.snd_queue_len as ifq is replaced
by a buf_ring
and ifnet functions
- add memory barriers to <machine/atomic.h>
- update drivers to only conditionally define their own
- add lockless producer / consumer ring buffer
- remove ring buffer implementation from cxgb and update its callers
- add if_transmit(struct ifnet *ifp, struct mbuf *m) to ifnet to
allow drivers to efficiently manage multiple hardware queues
(i.e. not serialize all packets through one ifq)
- expose if_qflush to allow drivers to flush any driver managed queues
This work was supported by Bitgravity Inc. and Chelsio Inc.
1) Fix a bug in dealing with the Alerus 1006 PHY which prevented the
device from ever coming back up once it had been set to down.
2) Add a kernel tunable (hw.cxgb.snd_queue_len) which makes it possible
to give the device more than IFQ_MAXLEN entries in its send queue. The
default remains 50.
3) Add code to place the card'd identification and serial number into
its description (%desc) so that users can tell which card they have
installed.
and output, set BUS_DMA_COHERENT when creating the DMA map used for
loading the buffer. As a side-effect this solves locking issues on
sparc64 when dcons(4) calls bus_dmamap_sync(9) while in an interrupt
filter, which are executed in a critical section, and iommu(4) has
to use a sleep lock when taking advantage of the streaming buffer.
Reported and tested by: kensmith
Approved by: simokawa
For some reason the nmdm(4) driver doesn't use CALLOUT_MPSAFE, even
though we live in the MPSAFE TTY era. Add the CALLOUT_MPSAFE flags.
System survives.
for virtualization.
Instead of initializing the affected global variables at instatiation,
assign initial values to them in initializer functions. As a rule,
initialization at instatiation for such variables should never be
introduced again from now on. Furthermore, enclose all instantiations
of such global variables in #ifdef VIMAGE_GLOBALS blocks.
Essentialy, this change should have zero functional impact. In the next
phase of merging network stack virtualization infrastructure from
p4/vimage branch, the new initialization methology will allow us to
switch between using global variables and their counterparts residing in
virtualization containers with minimum code churn, and in the long run
allow us to intialize multiple instances of such container structures.
Discussed at: devsummit Strassburg
Reviewed by: bz, julian
Approved by: julian (mentor)
Obtained from: //depot/projects/vimage-commit2/...
X-MFC after: never
Sponsored by: NLnet Foundation, The FreeBSD Foundation
src/sys/dev/usb2/core/usbdevs
src/sys/dev/usb2/include/urio2_ioctl.h
src/sys/dev/usb2/storage/ustorage2_fs.h
These files are not used any more.
src/usr.sbin/Makefile
src/etc/mtree/BSD.include.dist
src/include/Makefile
src/lib/Makefile
src/share/man/man7/hier.7
src/share/mk/bsd.libnames.mk
src/etc/mtree/BSD.include.dist
Make "usbconfig" and "libusb20" a part of the default build.
src/sys/dev/usb/rio500_usb.h
src/sys/dev/usb2/storage/urio2.c
Use common include file.
src/sys/dev/usb2/bluetooth/ng_ubt2.c
Make USB bluetooth depend on "ng_hci" module.
src/sys/dev/usb2/controller/ehci2.c
src/sys/dev/usb2/controller/ehci2.h
Patches for Marvell EHCI.
src/sys/dev/usb2/core/usb2_busdma.c
Bugfix for 64-bit platforms. Need to unload the previously loaded DMA
map and some cleanup regarding some corner cases.
src/sys/dev/usb2/core/usb2_core.h
src/sys/dev/usb2/core/usb2_dev.c
src/sys/dev/usb2/core/usb2_dev.h
Bugfix for libusb filesystem interface.
New feature: Add support for filtering device data at the expense of the
userland process.
Add some more comments.
Some minor code styling.
Remove unused function, usb2_fifo_get_data_next().
Fix an issue about "fifo_index" being used instead of "ep_index".
src/sys/dev/usb2/core/usb2_device.c
src/sys/dev/usb2/core/usb2_generic.c
Bugfix for Linux USB compat layer. Do not free non-generic FIFOs when
doing an alternate setting.
Cleanup USB IOCTL and USB reference handling.
Fix a corner case where USB-FS was left initialised after
setting a new configuration or alternate setting.
src/sys/dev/usb2/core/usb2_hub.c
Improvement: Check all USB HUB ports by default at least one time.
src/sys/dev/usb2/core/usb2_request.c
Bugfix: Make sure destination ASCII string is properly zero terminated
in all cases.
Improvement: Skip invalid characters instead of replacing with a dot.
src/sys/dev/usb2/core/usb2_util.c
src/sys/dev/usb2/image/uscanner2.c
Spelling.
src/sys/dev/usb2/include/Makefile
Share "usbdevs" with the old USB stack.
src/sys/dev/usb2/include/usb2_devid.h
src/sys/dev/usb2/include/usb2_devtable.h
Regenerate files.
Alfred: Please fix the RCS tag at the top.
src/sys/dev/usb2/include/usb2_ioctl.h
Fix compilation of "kdump".
src/sys/dev/usb2/serial/ubsa2.c
src/sys/dev/usb2/serial/ugensa2.c
Remove device ID's which will end up in a new 3G driver.
src/sys/dev/usb2/sound/uaudio2.c
Correct a debug printout.
src/sys/dev/usb2/storage/umass2.c
Sync with old USB stack.
src/lib/libusb20/libusb20.3
Add more documentation.
src/lib/libusb20/libusb20.c
Various bugfixes and improvements.
src/usr.sbin/usbconfig/dump.c
src/usr.sbin/usbconfig/usbconfig.c
New commands for dumping strings and doing custom USB requests from
the command line.
Remove keyword requirements from generated files:
"head/sys/dev/usb2/include/usb2_devid.h"
"head/sys/dev/usb2/include/usb2_devtable.h"
- An "at" hint now reserves a device name.
- A new BUS_HINT_DEVICE_UNIT method is added to the bus interface. When
determining the unit number of a device, this method is invoked to
let the bus driver specify the unit of a device given a specific
devclass. This is the only way a device can be given a name reserved
via an "at" hint.
- Implement BUS_HINT_DEVICE_UNIT() for the acpi(4) and isa(4) bus drivers.
Both of these busses implement this by comparing the resources for a
given hint device with the resources enumerated by ACPI/PnPBIOS and
wire a unit if the hint resources are a subset of the "real" resources.
- Use bus_hinted_children() for adding hinted devices on isa(4) busses
now instead of doing it by hand.
- Remove the unit kludging from sio(4) as it is no longer necessary.
Prodding from: peter, imp
OK'd by: marcel
MFC after: 1 month
read before we configure the card, so we can implement
/dev/cardbus*.cis. Also, do this on a per-child basis, so we now have
a different name than before. I think i'll have to fix that for some
legacy tools to keep working.
I can now do a dumpcis on my running atheros card and have it still work!
redundant malloc/free. Add comments about how this should really be
done. Fix an overly verbose comment about under 1MB mapping: go ahead
and set the bits, but we ignore them.
- If the flag is set and auto-select fails, assume disk is not present.
- Set disk empty flag only when the floppy controller reset is needed.
It fixes regression introduced in r1.311, which prevented it from ignoring
errors. Now fdformat(1) and dd(1) with conv=noerror option can continue
when read/write errors occur as they should.
- Do not retry disk probing as it is extremely slow and pointless.
- Move the disk probing code into a separate function.
- Do not reset disk empty flag if write-protect check fails somehow.
PR: kern/116538[1]
the softc is reset a few times during probing.
Print 'changing to modem mode' messages if booting verbose to show the
reason for the time delay. Note: Some devices (Huawei for one) take 20
seconds to appear on the USB bus).
can be controlled by ifconfig(8). Note, VLAN hardware tagging
controls still lacks required handler but it requires more driver
cleanups so I didn't touch that part.
PR: kern/128766
- Fix to ioctl path in which the length could be 0 which means
no data in/out from LSI.
- Fix to ioctl path in which the data in the sense data space
of the ioctl packet is a really a pointer to some location in
user-space. From LSI re-worked a bit by me.
- Add HW support for next gen cards from LSI.
Thanks to LSI for their support!
Submitted by: jhb, LSI
MFC after: 3 days
The same (vendor, product) tuple is used for aue(4) adapters,
but I am not sure if the quirk is correct. I'm using the USB
device 'release' info to skip aue(4) detection right now, but
if there's a better way to differentiate between USB-LAN and
USB Bluetooth we should update the quirk.
Reviewed by: imp, rink
MFC after: 2 weeks
controller. The controller is also known as L1E(AR8121) and
L2E(AR8113/AR8114). Unlike its predecessor Attansic L1,
AR8121/AR8113/AR8114 uses completely different Rx logic such that
it requires separate driver. Datasheet for AR81xx is not available
to open source driver writers but it shares large part of Tx and
PHY logic of L1. I still don't understand some part of register
meaning and some MAC statistics counters but the driver seems to
have no critical issues for performance and stability.
The AR81xx requires copy operation to pass received frames to upper
stack such that ale(4) consumes a lot of CPU cycles than that of
other controller. A couple of silicon bugs also adds more CPU
cycles to address the known hardware bug. However, if you have fast
CPU you can still saturate the link.
Currently ale(4) supports the following hardware features.
- MSI.
- TCP Segmentation offload.
- Hardware VLAN tag insertion/stripping with checksum offload.
- Tx TCP/UDP checksum offload and Rx IP/TCP/UDP checksum offload.
- Tx/Rx interrupt moderation.
- Hardware statistics counters.
- Jumbo frame.
- WOL.
AR81xx PCIe ethernet controllers are mainly found on ASUS EeePC or
P5Q series of ASUS motherboards. Special thanks to Jeremy Chadwick
who sent the hardware to me. Without his donation writing a driver
for AR81xx would never have been possible. Big thanks to all people
who reported feedback or tested patches.
HW donated by: koitsu
Tested by: bsam, Joao Barros <joao.barros <> gmail DOT com >
Jan Henrik Sylvester <me <> janh DOT de >
Ivan Brawley < ivan <> brawley DOT id DOT au >,
CURRENT ML
- Do not let individual KLD module unregister firmware image loaded by ispfw
or vice versa.
- Make 'kldunload ispfw' actually unregister all firmware images loaded by
ispfw, not just 'isp_1040'.
- Print which KLD module actually loaded the firmware image.
- Remove unused return value from do_load_fw() and do_unload_fw() and remove
duplicate sys/param.h while I am here.
dependencies. A 'struct pmc_classdep' structure describes operations
on PMCs; 'struct pmc_mdep' contains one or more 'struct pmc_classdep'
structures depending on the CPU in question.
Inside PMC class dependent code, row indices are relative to the
PMCs supported by the PMC class; MI code in "hwpmc_mod.c" translates
global row indices before invoking class dependent operations.
- Augment the OP_GETCPUINFO request with the number of PMCs present
in a PMC class.
- Move code common to Intel CPUs to file "hwpmc_intel.c".
- Move TSC handling to file "hwpmc_tsc.c".
On RELENG_6 (and probably RELENG_7) we see our syscons windows and
pseudo-terminals have the following buffer sizes:
| LINE RAW CAN OUT IHIWT ILOWT OHWT LWT COL STATE SESS PGID DISC
| ttyv0 0 0 0 7680 6720 2052 256 7 OCcl 1146 1146 term
| ttyp0 0 0 0 7680 6720 1296 256 0 OCc 82033 82033 term
These buffer sizes make no sense, because we often have much more output
than input, but I guess having higher input buffer sizes improves
guarantees of the system.
On MPSAFE TTY I just sent both the input and output buffer sizes to 7
KB, which is pretty big on a standard FreeBSD install with 8 syscons
windows and some PTY's. Reduce the baud rate to 9600 baud, which means
we now have the following buffer sizes:
| LINE INQ CAN LIN LOW OUTQ USE LOW COL SESS PGID STATE
| ttyv0 1920 0 0 192 1984 0 199 7 2401 2401 Oil
| pts/0 1920 0 0 192 1984 0 199 5631 1305 2526 Oi
This is a lot smaller, but for pseudo-devices this should be good
enough. You need to do a lot of punching to fill up a 7.5 KB input
buffer. If it turns out things don't work out this way, we'll just
switch to 19200 baud.
NATM needs 'struct in_addr' to compile, which is a problem on its own
but include in.h for now if we have NATM but neither INET or INET6.
MFC after: 2 months
the sc does not have 'an_have_rssimap' variable.
Add an ANCACHE check to poperly hide the case and make an(4)
compile without INET.
MFC after: 2 months
Because the TTY hooks interface was not finished when I imported the
MPSAFE TTY layer, I had to disconnect the snp(4) driver. This snp(4)
implementation has been sitting in my P4 branch for some time now.
Unfortunately it still doesn't use the same error handling as snp(4)
(returning codes through FIONREAD), but it should already be usable.
I'm committing this to SVN, hoping someone else could polish off its
rough edges. It's always better than having a broken driver sitting in
the tree.
Note that these changes will not make the driver work on powerpc, but it should fix at least the i386/amd64 cases.
Obtained from: //depot/projects/usb/src/sys/dev/usb2/wlan/if_zyd2.c#20
Noticed by: jeli, ed
vnode in question does not need to be held. All the data structures used
during the name lookup are protected by the global name cache lock.
Instead, the caller merely needs to ensure a reference is held on the
vnode (such as vhold()) to keep it from being freed.
In the case of procfs' <pid>/file entry, grab the process lock while we
gain a new reference (via vhold()) on p_textvp to fully close races with
execve(2).
For the kern.proc.vmmap sysctl handler, use a shared vnode lock around
the call to VOP_GETATTR() rather than an exclusive lock.
MFC after: 1 month
that includes significant features and SMP safety.
This commit includes a more or less complete rewrite of the *BSD USB
stack, including Host Controller and Device Controller drivers and
updating all existing USB drivers to use the new USB API:
1) A brief feature list:
- A new and mutex enabled USB API.
- Many USB drivers are now running Giant free.
- Linux USB kernel compatibility layer.
- New UGEN backend and libusb library, finally solves the "driver
unloading" problem. The new BSD licensed libusb20 library is fully
compatible with libusb-0.1.12 from sourceforge.
- New "usbconfig" utility, for easy configuration of USB.
- Full support for Split transactions, which means you can use your
full speed USB audio device on a high speed USB HUB.
- Full support for HS ISOC transactions, which makes writing drivers
for various HS webcams possible, for example.
- Full support for USB on embedded platforms, mostly cache flushing
and buffer invalidating stuff.
- Safer parsing of USB descriptors.
- Autodetect of annoying USB install disks.
- Support for USB device side mode, also called USB gadget mode,
using the same API like the USB host side. In other words the new
USB stack is symmetric with regard to host and device side.
- Support for USB transfers like I/O vectors, means more throughput
and less interrupts.
- ... see the FreeBSD quarterly status reports under "USB project"
2) To enable the driver in the default kernel build:
2.a) Remove all existing USB device options from your kernel config
file.
2.b) Add the following USB device options to your kernel configuration
file:
# USB core support
device usb2_core
# USB controller support
device usb2_controller
device usb2_controller_ehci
device usb2_controller_ohci
device usb2_controller_uhci
# USB mass storage support
device usb2_storage
device usb2_storage_mass
# USB ethernet support, requires miibus
device usb2_ethernet
device usb2_ethernet_aue
device usb2_ethernet_axe
device usb2_ethernet_cdce
device usb2_ethernet_cue
device usb2_ethernet_kue
device usb2_ethernet_rue
device usb2_ethernet_dav
# USB wireless LAN support
device usb2_wlan
device usb2_wlan_rum
device usb2_wlan_ral
device usb2_wlan_zyd
# USB serial device support
device usb2_serial
device usb2_serial_ark
device usb2_serial_bsa
device usb2_serial_bser
device usb2_serial_chcom
device usb2_serial_cycom
device usb2_serial_foma
device usb2_serial_ftdi
device usb2_serial_gensa
device usb2_serial_ipaq
device usb2_serial_lpt
device usb2_serial_mct
device usb2_serial_modem
device usb2_serial_moscom
device usb2_serial_plcom
device usb2_serial_visor
device usb2_serial_vscom
# USB bluetooth support
device usb2_bluetooth
device usb2_bluetooth_ng
# USB input device support
device usb2_input
device usb2_input_hid
device usb2_input_kbd
device usb2_input_ms
# USB sound and MIDI device support
device usb2_sound
2) To enable the driver at runtime:
2.a) Unload all existing USB modules. If USB is compiled into the
kernel then you might have to build a new kernel.
2.b) Load the "usb2_xxx.ko" modules under /boot/kernel having the same
base name like the kernel device option.
Submitted by: Hans Petter Selasky hselasky at c2i dot net
Reviewed by: imp, alfred
Also: Change the initialisation of the command string to a static
initialiser. Verify it against the output of umass.c when being sent a
command using 'camcontrol eject da0' to a Bulk-Only device.
This should make those devices work that need a SCSI eject command to
switch to modem mode (Novatel 950D and others).
allocating resources to read the CIS. I'm not sure when this changed,
but it is totally wrong. Also, add a minor improvement to the
debugging.
This should help everybody trying to run dumpcis on atheros wireless
card as well.
MFC after: 2 days
right... Good thing the size was ignored...
Where this macro is used, there's no reason to do it anyway. There
seems to have been some old-time confusion between the CIS pointer
definition, and the BAR definitions at the base of this bug.
compiled into the main AMR driver. It's code that is nice to have but not
required for normal operation, and it is reported to cause problems for some
people.
For an unknown reason the touch pad of my PowerBook generates button 5
events when you operate it. This causes the adb_mouse code to convert
them to button 2 events, which is not what we want.
Add a new flag, AMS_TOUCHPAD, which is used to distinguish the touch
pad. When set, don't convert button events of unknown buttons to the
last button.
There are still three problems left with respect to user input:
- The mouse button events are not properly processed when the touch pad
isn't touched.
- The arrow keys on the keyboard don't work inside X11.
- The power button isn't handled by the kernel, similar to the ACPI
power button on i386/amd64.
Approved by: nwhitehorn
use process ID as ACPI thread ID. Concurrent requests with equal thread
IDs broke ACPI mutexes operation causing unpredictable errors including
AE_AML_MUTEX_NOT_ACQUIRED that I have seen.
Use kernel thread ID instead of process ID for ACPI thread.
Right now ams_read() uses cv_wait() to wait for new data to arrive on
the mouse device. This means that when you run `cat /dev/ams0', it
cannot be interrupted directly. After you press ^C, you first need to
move the mouse before cat will quit. Make this function use
cv_wait_sig(), which allows it to be interrupted directly.
Reviewed by: nwhitehorn
capabilities reported by the ap. These need to be cross-checked
against the local configuration in the vap. Previously we were
only checking the ap capabilities which meant that if an ap reported
it was ff-capable but we were not setup to use them we'd try to do
ff aggregation and drop the frame.
There are a number of problems to be fixed here but applying this
fix immediately as the problem causes all traffic to stop (and has
not workaround).
Reported by: Ashish Shukla
sdhci supports up to 65535 blocks transfers, at91_mci - one block.
Enable multiblock operations disabled before to follow at91_mci driver
limitations.
Reviewed by: imp@
driver (rev 1.3), by Joerg Sonnenberger.
Note: This change is untested as I do not own the hardware. Let me know
if things work or do not work for you by sending me the output dmesg (and
usbctl -f /dev/usbX if possible). Thanks.
for the BCM5714 revision A0 when in a multi-port configuration
and unconditionally for the remainder of the class of BCM575X
and beyond chips.
This was prodded by mav and is based on a suggestion and a
patch submitted by jhb.
Reviewed by: jhb
MFC after: 2 months
rs400/rs480 should clear the RADEON_BUS_MASTER_DIS bit. This should get
the rs485 IGP chips going again.
Approved by: jhb (mentor)
Obtained from: drm git master
making the use of sc_hwmap to do direct mapping impractical. Switch to
indexing by the rate index instead of the rate code and adjust associated
state and logic appropriately. This has several benefits including
simplification of the led code.
o fix radiotap capture of HT rates
o fix conditional compilation of HT radiotap support to be based on the
hal having 5416 support; not the ABI version as hal builds may or may
not include 5416 support
o update tx rssi data only when an ACK was received
o return tx rssi from sampled data instead of the last frame
o track noise floor
o return rx rssi and noise floor (was broken)
o pass country code, outdoor indication, and ecm mode into the hal
when requesting a channel list
o add a console msg when regulatory setup fails
o add placeholder code to map between Atheros sku's and 802.11 sku's
that handles only the debug country code used to unlock the full
channel list (to be used only for debugging)
o fix multiple instances of mismapping the 802.11 location to the
outdoor indication (anywhere may be outdoor also)
in sta and adhoc modes; this should've been done forever ago as most all
drivers use this hook to set per-station transmit parameters such as for
tx rate control
o adjust drivers to remove explicit calls to the driver newassoc method
The cn_unit and cn_tp fields don't seem to be used anywhere. Some
drivers set them, while others don't. Just remove them, in an attempt to
make our consdev code a little easier to understand.
G3 as well as the internal ADB keyboard and mice in PowerBooks and iBooks. This
also brings in Mac GPIO support, for which we should eventually have a better
interface.
Obtained from: NetBSD (CUDA and PMU drivers)
Olaf Kirch noticed that the i915_set_status_page() function of the i915
kernel driver calls ioremap with an address offset that is supplied by
userspace via ioctl. The function zeroes the mapped memory via memset
and tells the hardware about the address. Turns out that access to that
ioctl is not restricted to root so users could probably exploit that to
do nasty things. We haven't tried to write actual exploit code though.
It only affects the Intel G33 series and newer.
Approved by: bz (secteam)
Obtained from: Intel drm repo
Security: CVE-2008-3831
Memory Interface (CFI). The flash memory can be read and written
to through /dev/cfi# and an ioctl() exists so processes can read
the query information.
The driver supports the AMD and Intel command set, though only
the AMD command has been tested.
Obtained from: Juniper Networks, Inc.
with several points unappropriate for the present parser. This patch
disables input-to-output analog monitoring but instead fixes recording.
Tested by Tobias Grosser on ThinkPad T61p.
might make Qualcomm and Option cards (which have all endpoints in 1
interface) work.
- Change the USB buffer sizes to depend on the transfer speed. With UMTS
we use a buffer 384k / 1000 frames/sec * 50msecs =~ 15kB for example.
- Add a MODULE_VERSION statement
but I inadvertently overwrote the change when I synced to git. Commit
the fix in both places, so this doesn't happen again.
Approved by: jhb (mentor)
MFC after: 2 weeks
This update fixes a transmit bug in the multi-queue (MSI-X) firmware
which happens when RDMAs complete out of order, and provides
improved support for the new Myri10GE NIC models (10G-PCIE-8Bx)
Sponsored by: Myricom Inc.
MFC after:3 days
With our new TTY layer we use a two step device destruction procedure.
The TTY first gets abandoned by the device driver. When the TTY layer
notices all threads have left the TTY layer, it deallocates the TTY.
This means that the device unit number should not be reused before a
callback from the TTY layer to the device driver has been made. newbus
doesn't seem to support this concept (yet), so right now just add a
destructor with a big comment in it. It's not ideal, but at least it's
better than panicing.
Reported by: rnoland
Driver supports PCI devices with class 8 and subclass 5 according to
SD Host Controller Specification.
Update NOTES, enable module and static build.
Enable related mmc and mmcsd modules build.
Discussed on: mobile@, current@
other fixes:
- Add pointers back to device_t objects in softc structures instead
of storing the unit and using devclass_get_device().
- Add 'lpbb', 'pcf', 'pps', and 'vpo' child devices to every 'ppbus' device
instead of just the first one.
- Store softc pointers in si_drv1 of character devices instead of
pulling the unit number from the minor number and using
devclass_get_softc() and devclass_get_device().
- Store the LP_BYPASS flag in si_drv2 instead of encoding it in the minor
number.
- Destroy character devices for lpt(4) when detaching the device.
- Use bus_print_child_footer() instead of duplicating it in
ppbus_print_child() and fix ppbus_print_child()'s return value.
- Remove unused AVM ivar from ppbus.
- Don't store the 'mode' ivar in the ppbus ivars since we always fetch it
from the parent anyway.
- Try to detach all the child devices before deleting them in
ppbus_detach().
- Use pause() instead of a tsleep() on a dummy address when polling the
ppbus.
- Use if_printf() and device_printf() instead of explicit names with unit
numbers.
Silence on: current@
Erase operation gives card's logic information about unused areas to help it
implement wear-leveling with lower overhead comparing to usual writing.
Erase is much faster then write and does not depends on data bus speed.
Also as result of hitting in-card write logic optimizations I have measured
up to 50% performance boost on writing undersized blocks into preerased areas.
At the same time there are strict limitations on size and allignment of erase
operations. We can erase only blocks aligned to the erase sector size and
with size multiple of it. Different cards has different erase sector size
which usually varies from 64KB to 4MB. SD cards actually allow to erase
smaller blocks, but it is much more expensive as it is implemented via
read-erase-write sequence and so not sutable for the BIO_DELETE purposes.
Reviewed by: imp@
(still a power of 2) rather than 63k transfers. Even with 63k transfers
some machines (such as Dell SC1435's) were experiencing chronic data
corruption.
- Use the MIO method to talk to the Serverworks HT1000_S1 SATA controller
like all the other SATA controllers rather than the compat PATA
method. This lets the controller see all 4 SATA ports and also
matches the behavior of the Linux driver.
Silence from: sos
MFC after: 3 days
bank instead of copper/fiber bank which in turn resulted in
wrong registers were accessed during PHY operation. It is
believed that page 0 should be used for copper PHY so reinitialize
E1000_EADR to select default copper PHY.
This fixes link establishment issue of nfe(4) on Sun Fire X4140.
OpenBSD also has similimar patch but they just reset the E1000_EADR
register to page 0. However some Marvell PHYs((88E3082, 88E1000)
don't have the extended address register and the meaning of the
register is quite different for each PHY model. So selecting copper
PHY is limited to 88E1149 PHY which seems to be the only one that
exhibits link establishment problem. If parent device know the type
of PHY(either copper or fiber) that information should be notified
to PHY driver but there is no good way to pass this information yet.
Reported by: thompsa
Reviewed by: thompsa
the Sierra and Novatel devices, ignore all umass devices and hide the umass
devices that represent the CD ROM devices (but not the SD card slot in the
Huawei Mobile dongle).
Note: This driver in FBSD7 seems to suffer from memory corruption when used
with an Option GT Quad. The E220 however works flawlessly.
Also add the ID for the Option GTMaxHSUPA, provided by Olivier Fromme.
o better quality of the movement smoothing
o more features such as tap-hold and virtual scrolling
Support must still be enabled with this line in your /boot/loader.conf:
hw.psm.synaptics_support="1"
The following sysctls were removed:
hw.psm.synaptics.low_speed_threshold
hw.psm.synaptics.min_movement
hw.psm.synaptics.squelch_level
An overview of this new driver and a short documentation about the added
sysctls is available on the wiki:
http://wiki.freebsd.org/SynapticsTouchpad
simplifies certain device attachments (Kauai ATA, for instance), and makes
possible others on new hardware.
On G5 systems, there are several otherwise standard PCI devices
(Serverworks SATA) that will not allow their interrupt properties to be
written, so this information must be supplied directly from Open Firmware.
Obtained from: sparc64
This supports 1Gbps Ethernet engine found on ARM-based SOCs (Orion, Kirkwood,
Discovery), as well as on system controllers for PowerPC processors (MV64430,
MV6446x).
The following advanced features are supported:
- multicast
- VLAN tagging
- IP/TCP/UDP checksum calculation offloading
- polling
- interrupt coalescing
Obtained from: Marvell, Semihalf
the last byte of the ethernet address was not read which in turn
resulted in getting 5 out of the 6 bytes of ethernet address and
always returned ENOENT. I did not notice the bug on FPGA version
because of additional configuration data in EEPROM.
Pointed out by: bouyer at NetBSD
example the Huawei Mobile has an SD card slot on the second interface.
- Do not attach to Qualcomm and Novatel cards. If ignored these cards will
switch to modem mode automatically it seems.
- Reduce the priority on generic attachment to the appropriate level.
Note: A better solution is to send an eject command straightaway, but that can
be left till later.
* Orion
- 88F5181
- 88F5182
- 88F5281
* Kirkwood
- 88F6281
* Discovery
- MV78100
The above families of SOCs are built around CPU cores compliant with ARMv5TE
instruction set architecture definition. They share a number of integrated
peripherals. This commit brings support for the following basic elements:
* GPIO
* Interrupt controller
* L1, L2 cache
* Timers, watchdog, RTC
* TWSI (I2C)
* UART
Other peripherals drivers will be introduced separately.
Reviewed by: imp, marcel, stass (Thanks guys!)
Obtained from: Marvell, Semihalf
will ease the identification of memory leaks as the OS will be able to track
allocations for us by malloc type. vmstat -m will show all of the
allocations.
Convert the calls to drm_alloc() and friends, which are used in shared code
to static __inline__ while we are here.
Approved by: jhb (mentor)
from operating on a list with a single item. This code is used much more by
the i915 driver with xorg-7.4. Correct it to match the actual linux
implementation.
Approved by: jhb (mentor)
busmastering support. This also adds register definitions for MSI support,
which we will be using shortly.
Approved by: jhb (mentor)
Obtained from: drm git master
macio's enable-enet word, which apparently does nothing on some machines,
open an OF instance of the ethernet controller. This fixes cold booting
from disk on my Blue & White G3.
MFC after: 3 days
device id is JMC260 family. Previously it just verified the deivce
is JMC260 Rev A0. This will make it easy for newer JMC2xx support.
Pointed out by: bouyer at NetBSD
This was located in the ubsa driver, but should be moved into a separate
driver:
- 3G modems provide multiple serial ports to allow AT commands while the PPP
connection is up.
- 3G modems do not provide baud rate or other serial port settings.
- Huawei cards need specific initialisation.
- ubsa is for Belkin adapters, an Linuxy choice for another device like 3G.
Speeds achieved here with a weak signal at best is ~40kb/s (UMTS). No spooky
STALLED messages as well.
Next: Move over all entries for Sierra and Novatel cards once I have found
testers, and implemented serial port enumeration for Sierra (or rather have
Andrea Guzzo do it). They list all endpoints in 1 iface instead of 4 ifaces.
Submitted by: aguzzo@anywi.com
MFC after: 3 weeks
have in common right now is a memset. This saves a parameter to
these routines, as well as a level of indentation.
o Make mmc_get_bits a little clearer... It really only works on 128-bit
registers right now.
reduce ABI disruptions when new cpu types and new PMC events are added
in the future.
- Support alternate spellings for PMC events. Derive the canonical
spelling of an event name from its enumeration name in 'enum pmc_event'.
- Provide a way for users to disambiguate between identically named events
supported by multiple classes of PMCs in a CPU.
- Change libpmc's machine-dependent event specifier parsing code to
better support CPUs containing two or more classes of PMC resources.
If you just config KERNEL as usual there should be no apparent changes, you'll get all chipset support code compiled in.
However there is now a way to only compile in code for chipsets needed on a pr vendor basis. ATA now has the following "device" entries:
atacore: ATA core functionality, always needed for any ATA setup
atacard: CARDBUS support
atacbus: PC98 cbus support
ataisa: ISA bus support
atapci: PCI bus support only generic chipset support.
ataahci: AHCI support, also pulled in by some vendor modules.
ataacard, ataacerlabs, ataadaptec, ataamd, ataati, atacenatek, atacypress, atacyrix, atahighpoint, ataintel, ataite, atajmicron, atamarvell, atamicron, atanational, atanetcell, atanvidia, atapromise, ataserverworks, atasiliconimage, atasis, atavia; Vendor support, ie atavia for VIA chipsets
atadisk: ATA disk driver
ataraid: ATA softraid driver
atapicd: ATAPI cd/dvd driver
atapifd: ATAPI floppy/flashdisk driver
atapist: ATAPI tape driver
atausb: ATA<>USB bridge
atapicam: ATA<>CAM bridge
This makes it possible to config a kernel with just VIA chipset support by having the following ATA lines in the kernel config file:
device atacore
device atapci
device atavia
And then you need the atadisk, atapicd etc lines in there just as usual.
If you use ATA as modules loaded at boot there is few changes except the rename of the "ata" module to "atacore", things looks just as usual.
However under atapci you now have a whole bunch of vendor specific drivers, that you can kldload individually depending on you needs. Drivers have the same names as used in the kernel config explained above.
can reliably provoke data corruption on systems equipped with a
plenty of memory during high load.
Reported by: gnn via iXsystems
MFC candidate: RELENG_7_1, RELENG_7
We don't explicity check for error here and M_WAITOK will just put the
process to sleep waiting on resources to become available.
Suggested by jhb@
Approved by: jhb (mentor)
in GENERIC and LINT. [1]
- Rename hpt_dbg_level to hpt_iop_dbg_level to avoid multiple definition
of hpt_dbg_level (hptmv also has hpt_dbg_level).
PR: 127551 [1]
Reviewed by: scottl@
MFC after: 1 month
NDIS_TXPKTS and don't allocate unused extra spaces for sc->ndis_txarray
and sc->ndis_txpool.
PR: kern/127644
Submitted by: Antoine Pelisse <apelisse_at_gmail.com>
MFC after: 1 week
This reverts a private patch which is causing issues with many Intel chipsets.
I will review that patch and see what we need to do to fix it up later, but
for the time being, we will just get these chips working again.
This update contains a lot of code cleanup and is post gem merge
(no, we don't have gem support). It should prove much easier to read the
code now. A lot of thanks goes to vehemens for that work. I have adapted
the code to use cdevpriv for tracking per open file data. That alleviates
the old ugly hack that we used to try and accomplish the task and helped to
clean up the open / close behavior a good bit. This also replaces the hack
that was put in place a year or so ago to prevent radeons from locking up
with AIGLX enabled. I have had a couple of radeon testers report that it
still works as expected, though I no longer have radeon hardware to test with
myself. Other various fixes from the linux crew and Intel, many of
which are muddled in with the gem merge.
Approved by: jhb (mentor)
Obtained from: mesa/drm git master
MFC after: 2 weeks
obtained from Linux forcedeth driver.
While I'm here move creating a sysctl node for process_limit to
function nfe_sysctl_node().
Tested by: "Arno J. Klaassen" < arno <at> heho dot snv dot jussieu dot fr >
g33 based chips use a different method of identifying the gtt size.
g45 based chips gtt is located in a different area of stolen memory.
Approved by: jhb (mentor)
MFC after: 2 weeks
from the vimage project, as per plan established at devsummit 08/08:
http://wiki.freebsd.org/Image/Notes200808DevSummit
Introduce INIT_VNET_*() initializer macros, VNET_FOREACH() iterator
macros, and CURVNET_SET() context setting macros, all currently
resolving to NOPs.
Prepare for virtualization of selected SYSCTL objects by introducing a
family of SYSCTL_V_*() macros, currently resolving to their global
counterparts, i.e. SYSCTL_V_INT() == SYSCTL_INT().
Move selected #defines from sys/sys/vimage.h to newly introduced header
files specific to virtualized subsystems (sys/net/vnet.h,
sys/netinet/vinet.h etc.).
All the changes are verified to have zero functional impact at this
point in time by doing MD5 comparision between pre- and post-change
object files(*).
(*) netipsec/keysock.c did not validate depending on compile time options.
Implemented by: julian, bz, brooks, zec
Reviewed by: julian, bz, brooks, kris, rwatson, ...
Approved by: julian (mentor)
Obtained from: //depot/projects/vimage-commit2/...
X-MFC after: never
Sponsored by: NLnet Foundation, The FreeBSD Foundation
- Support for Myricom 10G-PCIE-8B NICs
- multi-slice firmware: fix a bug when the presence of 32-bit or
64-bit DMA addresses for interrupt queues and data is not uniform across
slices.
- Improves automatic selection between ethp_z8e/eth_z8e
Sponsored by: Myricom Inc.
- simplify page hold logic
- allow pages for processes other than that of curthread to
have pages held
- normalize the interface to more closely resemble the functions in
sys/vm
MFC after: 1 week
only mode and restore original value of extended address register
instead of overwriting it with page 1. There are still instance
information passing issue(e.g configured media type: fiber or
copper) from driver to PHY layer but this change make the selected
PHY work with 88E1112 PHY.
Reported by: Krzysztof Jedruczyk < beaker <at> hot dot pl >
Tested by: Krzysztof Jedruczyk < beaker <at> hot dot pl >
This should fix occasional Tx checksum corruption issue.
Reported by: Garrett Cooper < yanefbsd <at> gmail dot com >
Tested by: Garrett Cooper < yanefbsd <at> gmail dot com >
disabled by default because there's problems with it on AT91RM9200,
currently the only host controller in the tree. I've not had time to
track those problems to ground. I'm committing because this is
important for other host controllers that are in the pipeline.
Submitted by: mav@
but an RW mapping exists for the underlying page. This change fixes the bug by using the
page / NULL returned from pmap_extract_and_hold to determine whether or not vm_fault needs
to be called.
The bug was pointed out by alc.
MFC after: 3 days
former more explicitly tells the compiler that you want an empty loop.
There are some lint programs that use this hint to avoid generating
warnings.
No functional change...
After I removed all the unit2minor()/minor2unit() calls from the kernel
yesterday, I realised calling minor() everywhere is quite confusing.
Character devices now only have the ability to store a unit number, not
a minor number. Remove the confusion by using dev2unit() everywhere.
This commit could also be considered as a bug fix. A lot of drivers call
minor(), while they should actually be calling dev2unit(). In -CURRENT
this isn't a problem, but it turns out we never had any problem reports
related to that issue in the past. I suspect not many people connect
more than 256 pieces of the same hardware.
Reviewed by: kib
When I changed kern_conf.c three months ago I made device unit numbers
equal to (unneeded) device minor numbers. We used to require
bitshifting, because there were eight bits in the middle that were
reserved for a device major number. Not very long after I turned
dev2unit(), minor(), unit2minor() and minor2unit() into macro's.
The unit2minor() and minor2unit() macro's were no-ops.
We'd better not remove these four macro's from the kernel, because there
is a lot of (external) code that may still depend on them. For now it's
harmless to remove all invocations of unit2minor() and minor2unit().
Reviewed by: kib
Thanks goes to ITE who provided docs and feedback and made this possible.
Minor fixups to the Intel ICH code for bugs found while doing this.
(ITE8213 is very semilar to an Intel ICH)
MFC after: 1 week
Kick the device into the right mode if it comes up as a flash-disk.
Set the buffers to a sensible 1024 bytes instead of a far too small
default.
Don't attempt to change speed, baud, parity and such, the device does
not understand it.
have hardware ram buffer. The silicon bug seem to be triggered by
pause frames if receive buffer is not aligned on FIFO word(8 bytes).
To workaround the issue, make sure to align Rx buffers on 8 bytes.
Unfortunately this workaround requires yet another Rx fixup for
strict alignment architecture machines to align IP header.
For newer hardwares that lacks ram buffer may not have this bug so
check number of available ram buffer size to see the existence of
ram buffer.
Reported by: Ian Freislich (ianf <at> clue dot co dot za), das
Tested by: Ian Freislich (ianf <at> clue dot co dot za)
