Now, if a release is specified, instead of just looking for a directory
with the same name as the release, try several possible directories (each
suffixed with the release name) relative to the base directory including
".", "releases/MACHINE", "snapshots/MACHINE", and each of those prefixed
with "pub/FreeBSD/". This will allow us to remove the evil symlinks under
pub/FreeBSD/releases/MACHINE/ to the snapshots on the ftp site.
names with a leading underscore. Notably, the 'stat' parameter in the
kld_stat() prototype conflicted with stat() and generated a BDE warning.
Approved by: peter
wrong bytes.
o Improve the public interface; use void* instead of char* or u_int64_t
to pass arbitrary data around.
Submitted by: kris ("horrible bug")
didn't bother to send a saved data pointers after the last transfer,
is not recorded in sgptr. This was only a problem if the target
reported non-zero status as we always check the residual in that case.
directories to not be printed. This is from OpenBSD (and I think
NetBSD also) and makes our mtree more compatible with other BSDs.
This makes cross compilation easier than it was before. Other changes
will be needed to allow NetBSD or OpenBSD to cross build on FreeBSD,
but this is a start.
Reviewed by: andrey
Obtained from: OpenBSD
Concentric Red Circles by: My own stupidity
- It's worthwhile to use untimeout(9), even though we must still protect
against "false" timeouts, because most of the time it saves having to
handle a dummy timeout event.
- Slight tweaks to the delayed ACK algorithm paramters.
a bug in some ftp servers (most notably ftp.vmunix.com) which report the
size of a file correctly in ascii mode, but report it as 0 in binary mode.
Reported by: asmodai
Also remove an unneeded initialization.
- Fix slowness when operating over fast connections, where the timeout(9)
granularity is on the same order of magnitude as the round trip time.
timeout(9) can happen up to 1 tick early, which was causing receive
ack timeouts to happen too early, causing bogus "lost" packets.
- Increase the local time counter to 64 bits to avoid roll-over.
- Keep statistics on memory allocation failures.
- Add a new option to always include the ack when sending data packets.
Might be useful in high packet loss situations. Might not.
Correct the BUILD_TCL macro. It was placing the target id
in the wrong bits. This was only an issue for adapters that
do not perform SCB paging (aha-3940AUW for instance).
Don't bother inlining ahc_index_busy_tcl. It is never
used in a performance critical path and is a bit chunky.
Correct ahc_index_busy_tcl to deal with "busy target tables"
embedded in the latter half of 64byte SCBs.
Don't initialize the busy target table to its empty state
until after we have finished extracting configuration
information from chip SRAM. In the common case of using
16 bytes of chip SRAM to do untagged target lookups,
we were trashing the last 8 targets configuration data.
(actually only target 8 because of the bug in the
BUILD_TCL macro).
Cram the "bus reset delivered" message back under bootverbose.
Fix the cleanup of the SCB busy target table when aborting
commands. If the lun is wildcarded, we must loop through
all possible luns.
aic7xxx.h:
Only bother supporting 64 luns right now. It doesn't seem
like either this driver or any peripherals will be doing
information unit transfers (where the lun number is a
32 bit integer) any time soon.
aic7xxx.seq:
Fix support for the aic7895. We must flush the data
FIFO if performing a manual transfer that is not
a multiple of 8 bytes. We were doing this quite
regularly for embedded cdbs.
Manaually flush the fifo on earlier adapters when
dealing with embedded cdbs too. We were stuffing
the FIFO with 16 bytes instead, but triggering
the flush is more efficient and allows us to
remove two instructions from the "copy_to_fifo"
routine.
pcic_attach() got a wrong pointer to pcic_slots since device haven't
set correct unit number yet, so always accessed elements of pcic_slots
which belong to pcic0 (unit number 0).
Now we set unit number to pcic device first, then access to pcic_slots
based on the unit number we've just set.
which sets the inoinfo's i_parent and i_dotdot to 0, but they never get
set to ROOTINO. This means that propagate will never find lost+found and
its descendents, subdirectories will remain DSTATE (instead of DFOUND)
even though they *are* correctly linked in, and pass4.c will try to
clear them unsuccessfully, thinking that there is no link count from the
DSTATE directory's parent. The result is that you need to run fsck twice
and get link count increasing errors (which are unexpected and fatal
when running in preen mode). The fix is to set i_parent and i_dotdot to
"parent" after the second cacheino() call in dir.c:allocdir().
Obtained from: "Ethan Solomita" <ethan@geocast.com> (of the NetBSD Project)
does bad things to /etc/make.conf in certain situations. Also
soften the "don't install crypto from the USA!" messages since,
except for RSA (which is still noted), that's not so true anymore.
Add spl/splx to various sensitive spots
Change semantics of the vmnet version of the device to keep VMware happy
(don't junk state when the device is closed)
Submitted by: vsilyaev@mindspring.com
