this is incorrect for Kite (AR9285) and any future chipsets that
override the EEPROM related routines.
It meant that a direct call to set the TX power would call the v14 EEPROM
AR5416/AR9280 calibration routines, rather than the v4k EEPROM routines
for the AR9285. It thus read the incorrect values from the EEPROM and
programmed garbage PDADC and TX power values into the hardware.
c65292b04b98d6a76d58c5a54ca8f81463bf24de to support new SIOCGIFDESCR
ioctl interface which was too late for libpcap 1.1.1.
Reported by: brucec
Noticed by: wxs
The test was support to check if SUID/SGID bits are removed on first
write, but actually we were checking if they were removed after close.
Now we can check if SUID/SGID bits are gone after first write.
While here add checks to see if when both SUID and SGID bits are set they are
both cleared on first write.
adjust the IEEE80211_HTRATE_MAXSIZE constant, only MCS0 - 76 are valid
the other bits in the mcsset IE (77 - 127) are either reserved or used
for TX parameters.
o bunch of variables are turned into uint8_t
o initial setting of namep[] in lookup() is removed
as it's only overwritten a few lines down
o kname is explicitly initialized in main() as BSS
in boot2 is not zeroed
o the setting and reading of "fmt" in load() is removed
o buf in printf() is made static to save space
Reviewed by: jhb
Tested by: me and Fabian Keil <freebsd-listen fabiankeil de>
This makes partitions between 50GiB and 2TiB (16TiB for 4k drives) print
correctly aligned.
While here, fix type of secsize. g_sectorsize() returns ssize_t, don't
store this in an unsigned var. Bump WARNS to 6.
MFC after: 4 weeks
- the default label now includes an a: partition by default
- the c: partition is no longer exported via devfs
- writing of the labels usually works in all cases, though the script
assumes half of them have to fail
It looks like these apply in both open and closed loop TX power control,
but the only merlin boards i have either have OL -or- a non-default power
offset, not both.
to both make things clearer, and to make it easier to write userland
code which pulls in these definitions without needing to pull in the
rest of the HAL.
This stuff should be deprecated at some point in the future once
the net80211 regulatory domain support encapsulates all of the
defintions here.
This is something bus clock related from what I can gather. It is needed for
the AR9220 based Ubiquiti SR71-12 and SR71-15 Mini-PCI NICs.
(Note: those NICs don't work right now because of earlier changes to handle
power table offset correctly. That'll be resolved in a follow-up commit.)
- fchmod(2),
- fchown(2),
- fchflags(2),
- fstat(2),
- ftruncate(2),
- fpathconf(2),
- lpathconf(2).
Make write(2) syscall to take descriptor instead of file name.
We implement descriptors by keeping track of open files and allowing to
reference them by the following syscalls. Because pjdfstest already supports
executing multiple syscalls from one command it works pretty well.
For example, the following command:
pjdfstest open foo "O_CREAT,O_RDWR" 0 : open bar "O_CREAT,O_RDONLY" 640 : fchmod 0 0666 : fchown 0 -1 20 : fchmod 1 0444
is equivalent of (error checking omitted):
int fd[2];
fd[0] = open("foo", O_CREAT | O_RDWR, 0);
fd[1] = open("bar", O_CREAT | O_RDONLY, 0640);
fchmod(fd[0], 0666);
fchown(fd[0], -1, 20);
fchmod(fd[1], 0444);
Merlin (ar9280) and later were full-reset if they're doing open-loop TX
power control but the TSF wasn't being saved/restored.
Add ar5212SetTsf64() which sets the 64 bit TSF appropriately.
partitions instead of partition's indexes. This may be useful with
GPT partitioning scheme or EBR without GEOM_PART_EBR_COMPAT option.
MFC after: 2 weeks
- No leapsecond in June 2011
- Add and update timezones for America/Juneau, America/Sitka,
America/Metlakatla
- Change of Summer time to Winter time in Chili happens in April
2011, not in March 2011.
- No leapsecond in June 2011
- Add and update timezones for America/Juneau, America/Sitka,
America/Metlakatla
- Change of Summer time to Winter time in Chili happens in April
2011, not in March 2011.
Obtained from: ftp://elsie.nci.nih.gov/pub/
value. Controllers that always require "store and forward" mode(
Davicom and PNIC 82C168) have no way to recover from TX underrun
except completely reinitializing hardware. Previously only Davicom
was reinitialized and the TX FIFO threshold was changed not to use
"store and forward" mode after reinitialization since the default
FIFO threshold value was 0. This effectively disabled Davicom
controller's "store and forward" mode once it encountered TX
underruns. In theory, this can cause watchodg timeouts.
Intel 21143 controller requires TX MAC should be idle before
changing TX FIFO threshold. So driver tried to disable TX MAC and
checked whether it saw the idle state of TX MAC. Driver should
perform full hardware reinitialization on failing to enter to idle
state and it should not touch TX MAC again once it performed full
reinitialization.
While I'm here remove resetting TX FIFO threshold to 0 when
interface is put into down state. If driver ever encountered TX
underrun, it's likely to trigger TX underrun again whenever
interface is brought to up again. Keeping old/learned TX FIFO
threshold value shall reduce the chance of seeing TX underrns in
next run.
