allowing the driver for the host-PCI-bridge to indicate that
reenumeration of the PCI busses isn't supported by returning
-1 instead of a valid PCI bus number. This is needed in order
support both Tomatillo, which don't support reenumeration and
thus are apparently intended to be used for independently
numbered PCI domains only, and Psycho bridges, whose busses
need to be reenumerated on at least some E450, without the
#ifndef currently used for sun4v in order to support multiple
independently PCI domains. The actual allocation/incrementation
of the PCI bus numbers is now done in psycho(4), though it
no longer establish a mapping between bus numbers and device
nodes like ofw_pci_alloc_busno() did as that functionality
wasn't used (but can easily brought back if really needed).
The now no longer used sys/sparc64/pci/ofw_pci.c is also
removed from sys/conf/files.sun4v as ofw_pci_alloc_busno()
wasn't used there in the first place.
- In ofw_pci_default_{adjust_busrange,intr_pending}() sanity
check that the device has a parent before passing it on.
- Make psycho_softcs static to sys/sparc64/pci/psycho.c as
it's not used outside of that module.
- In sys/sparc64/pci/ofw_pcib_subr.c remove the superfluous
inclusion of opt_global.h and correct the debug output for
adjusting the subordinate bus number.
to be compiled into every driver making use of it. Use a const instance
of struct gfb_font for this as the font isn't intended to be changed at
run-time and in order to accompany the font data with height and width
info.
This allocator uses a binary buddy system with a twist. First and
foremost, this allocator is required to support the implementation of
superpages. As a side effect, it enables a more robust implementation
of contigmalloc(9). Moreover, this reimplementation of
contigmalloc(9) eliminates the acquisition of Giant by
contigmalloc(..., M_NOWAIT, ...).
The twist is that this allocator tries to reduce the number of TLB
misses incurred by accesses through a direct map to small, UMA-managed
objects and page table pages. Roughly speaking, the physical pages
that are allocated for such purposes are clustered together in the
physical address space. The performance benefits vary. In the most
extreme case, a uniprocessor kernel running on an Opteron, I measured
an 18% reduction in system time during a buildworld.
This allocator does not implement page coloring. The reason is that
superpages have much the same effect. The contiguous physical memory
allocation necessary for a superpage is inherently colored.
Finally, the one caveat is that this allocator does not effectively
support prezeroed pages. I hope this is temporary. On i386, this is
a slight pessimization. However, on amd64, the beneficial effects of
the direct-map optimization outweigh the ill effects. I speculate
that this is true in general of machines with a direct map.
Approved by: re
Please note that, this is currently considered as an
experimental feature so there could be some rough
edges. Consult http://wiki.freebsd.org/TMPFS for
more information.
For now, connect tmpfs to build on i386 and amd64
architectures only. Please let us know if you have
success with other platforms.
This work was developed by Julio M. Merino Vidal
for NetBSD as a SoC project; Rohit Jalan ported it
from NetBSD to FreeBSD. Howard Su and Glen Leeder
are worked on it to continue this effort.
Obtained from: NetBSD via p4
Submitted by: Howard Su (with some minor changes)
Approved by: re (kensmith)
- Fix so VRF's will clean themselves up when no references are around.
- Allow sctp_ifa to be passed into inpcb_bind, addr_mgmt_ep_sa to bypass
normal validation checks.
- turn auto-asconf off for subset bound sockets
- Moves all logging to use KTR. This gets rid of most
of the logging #ifdef's with a few exceptions reducing
the number of config options for SCTP.
tunnels, and was not MPSAFE. The code can be easily restored in the
event that someone with an IPX over IP tunnel configuration can work
with me to test patches.
This removes one of five remaining consumers of NET_NEEDS_GIANT.
Approved by: re (kensmith)
- update to firmware version 4.1.0
- switch over to standard method for initializing cdevs (contributed by scottl@)
- break out timer_reclaim_task to be per-port
- move msix teardown into separate function
- fix bus_setup_intr for msi-x for the multi-port case so that msi-x resources
are not corrupted on unload
- handle 10/100/1000 base-T media and auto negotiation
- bind qset to cpu even for singleq case
- white space cleanups
- remove recursive PORT_LOCK
- move mtu setting to separate function
- stop and re-init port when changing mtu
- replace all direct references to m_data with calls to mtod
- handle attach failure better by not trying to de-initialize
taskqueues when they have not been allocated
- no longer default to jumbo frames
Sponsored by: Chelsio
MFC after: 3 days
and protocol-independent host mode multicast. The code is written to
accomodate IPv6, IGMPv3 and MLDv2 with only a little additional work.
This change only pertains to FreeBSD's use as a multicast end-station and
does not concern multicast routing; for an IGMPv3/MLDv2 router
implementation, consider the XORP project.
The work is based on Wilbert de Graaf's IGMPv3 code drop for FreeBSD 4.6,
which is available at: http://www.kloosterhof.com/wilbert/igmpv3.html
Summary
* IPv4 multicast socket processing is now moved out of ip_output.c
into a new module, in_mcast.c.
* The in_mcast.c module implements the IPv4 legacy any-source API in
terms of the protocol-independent source-specific API.
* Source filters are lazy allocated as the common case does not use them.
They are part of per inpcb state and are covered by the inpcb lock.
* struct ip_mreqn is now supported to allow applications to specify
multicast joins by interface index in the legacy IPv4 any-source API.
* In UDP, an incoming multicast datagram only requires that the source
port matches the 4-tuple if the socket was already bound by source port.
An unbound socket SHOULD be able to receive multicasts sent from an
ephemeral source port.
* The UDP socket multicast filter mode defaults to exclusive, that is,
sources present in the per-socket list will be blocked from delivery.
* The RFC 3678 userland functions have been added to libc: setsourcefilter,
getsourcefilter, setipv4sourcefilter, getipv4sourcefilter.
* Definitions for IGMPv3 are merged but not yet used.
* struct sockaddr_storage is now referenced from <netinet/in.h>. It
is therefore defined there if not already declared in the same way
as for the C99 types.
* The RFC 1724 hack (specify 0.0.0.0/8 addresses to IP_MULTICAST_IF
which are then interpreted as interface indexes) is now deprecated.
* A patch for the Rhyolite.com routed in the FreeBSD base system
is available in the -net archives. This only affects individuals
running RIPv1 or RIPv2 via point-to-point and/or unnumbered interfaces.
* Make IPv6 detach path similar to IPv4's in code flow; functionally same.
* Bump __FreeBSD_version to 700048; see UPDATING.
This work was financially supported by another FreeBSD committer.
Obtained from: p4://bms_netdev
Submitted by: Wilbert de Graaf (original work)
Reviewed by: rwatson (locking), silence from fenner,
net@ (but with encouragement)
o major overhaul of the way channels are handled: channels are now
fully enumerated and uniquely identify the operating characteristics;
these changes are visible to user applications which require changes
o make scanning support independent of the state machine to enable
background scanning and roaming
o move scanning support into loadable modules based on the operating
mode to enable different policies and reduce the memory footprint
on systems w/ constrained resources
o add background scanning in station mode (no support for adhoc/ibss
mode yet)
o significantly speedup sta mode scanning with a variety of techniques
o add roaming support when background scanning is supported; for now
we use a simple algorithm to trigger a roam: we threshold the rssi
and tx rate, if either drops too low we try to roam to a new ap
o add tx fragmentation support
o add first cut at 802.11n support: this code works with forthcoming
drivers but is incomplete; it's included now to establish a baseline
for other drivers to be developed and for user applications
o adjust max_linkhdr et. al. to reflect 802.11 requirements; this eliminates
prepending mbufs for traffic generated locally
o add support for Atheros protocol extensions; mainly the fast frames
encapsulation (note this can be used with any card that can tx+rx
large frames correctly)
o add sta support for ap's that beacon both WPA1+2 support
o change all data types from bsd-style to posix-style
o propagate noise floor data from drivers to net80211 and on to user apps
o correct various issues in the sta mode state machine related to handling
authentication and association failures
o enable the addition of sta mode power save support for drivers that need
net80211 support (not in this commit)
o remove old WI compatibility ioctls (wicontrol is officially dead)
o change the data structures returned for get sta info and get scan
results so future additions will not break user apps
o fixed tx rate is now maintained internally as an ieee rate and not an
index into the rate set; this needs to be extended to deal with
multi-mode operation
o add extended channel specifications to radiotap to enable 11n sniffing
Drivers:
o ath: add support for bg scanning, tx fragmentation, fast frames,
dynamic turbo (lightly tested), 11n (sniffing only and needs
new hal)
o awi: compile tested only
o ndis: lightly tested
o ipw: lightly tested
o iwi: add support for bg scanning (well tested but may have some
rough edges)
o ral, ural, rum: add suppoort for bg scanning, calibrate rssi data
o wi: lightly tested
This work is based on contributions by Atheros, kmacy, sephe, thompsa,
mlaier, kevlo, and others. Much of the scanning work was supported by
Atheros. The 11n work was supported by Marvell.
making the relevant files standard. This avoids duplication and
makes it easier to override/disable unwanted schemes. Since ARM
doesn't have a DEFAULTS configuration file, leave the source
files for the BSD and MBR partitioning schemes in files.arm for
now.
1.50 to help out with the GCC 2 to GCC 3 transition and it became
obsolete when C flags compatible with GCC 3.x became the default.
With GCC 4 in the tree this variable (i.e. GCC3) is beyond bogus
because it causes confusion when looking for the newly introduced
WITH_GCC3 option that helps the GCC 3 -> GCC 4 bump.
- Rework the entire pcm_channel structure:
* Remove rarely used link placeholder, instead, make each pcm_channel
as head/link of each own/each other. Unlock - Lock sequence due to
sleep malloc has been reduced.
* Implement "busy" queue which will contain list of busy/active
channels. This greatly reduce locking contention for example while
servicing interrupt for hardware with many channels or when virtual
channels reach its 256 peak channels.
- So I heard you like v chan ... O RLY?
Welcome to Virtual **Record** Channels (vrec, rec vchans, vchans for
recording, Rec-Chan, you decide), the ultimate solutions for your
nagging O_RDWR full-duplex wannabe (note: flash plugins) monopolizing
single record channel causing EBUSY. Vrec works exactly like Vchans
(or, should I rename it to "Vplay" :) , except that it operates on the
opposite direction (recording). Up to 256 vrecs (like vchans) are
possible.
Notes:
* Relocate dev.pcm.%d.{vchans,vchanformat,vchanrate} to each of its
respective node/direction:
dev.pcm.%d.play.* for "play" (cdev = dsp%d.vp%d)
dev.pcm.%d.rec.* for "record" (cdev = dsp%d.vr%d)
* Don't expect that it will magically give you ability to split
"recording source" (eg: 1 channel for cdrom, 1 channel for mic,
etc). Just admit that you only have a *single* recording source /
channel. Please bug your hardware vendor instead :)
- Bump maxautovchans from 4 to 16. For a full-fledged multimedia
desktop/workstation with too many soundservers installed (esound,
artsd, jackd, pulse/polypaudio, ding-dong pling plong mudkip fuh fuh,
etc), 4 seems inadequate. There will be no memory penalty here, since
virtual channels are allocate only by demand.
- Nuke/Rework the entire statically created cdev entries. Everything is
clonable through snd own clone manager which designed to withstand many
kind of abusive devfs droids such as:
* while : ; do /bin/test -e /dev/dsp ; done
* jot 16777216 0 | while read x ; do ls /dev/dsp0.$x ; done
* hundreds (could be thousands) concurrent threads/process opening
"/dev/dsp" (previously, this might result EBUSY even with just
3 contesting threads/procs).
o Reusable clone objects (instead of creating new one like there's no
tomorrow) after certain expiration deadline. The clone allocator will
decide whether to reuse, share, or creating new clone.
o Automatic garbage collector.
- Dynamic unit magic allocator. Maximum attached soundcards can be tuned
using tunable "hw.snd.maxunit" (Default to 512). Minimum is 16, and
maximum is 2048.
- ..other fixes, mostly related to concurrency issues.
joel@ will do the manpage updates on sound(4).
Have fun.
is expanded, size of expansion was not taken int consideration.
- Fix so vtag hash is 1 bigger so that it modulo's out
correctly, avoids a panic when restart with right modulo happens.
- do not dereference stcb when control->do_not_ref_stcb is set
- Fix up packet logging to not often use a lock and also to
add to options.
- Fix some logging option duplication in the sctputil.h
- upgrade to reflect state of 1.0.0.86
- move from firmware rev 3.2 to 4.0.0
- import driver bits for offload functionality
- remove binary distribution clause from top level files as it
runs counter to the intent of purely supporting the hardware
MFC after: 3 days
compiler invocation. This is just to help get over the hump of people
tracking down bugs that may cross the GCC 4.2 upgrade.
It is envisioned that this option goes away after a suitable amount
of time.
Implement all futex atomic operations in assembler to not depend on the
fuword() that does not allow to distinguish between -1 and failure return.
Correctly return 0 from atomic operations on success.
In collaboration with: rdivacky
Tested by: Scot Hetzel <swhetzel gmail com>, Milos Vyletel <mvyletel mzm cz>
Sponsored by: Google SoC 2007
Switch ia64 kernels to -fpic. This is likely wrong, but at least gets
ia64 kernels to compile and link with GCC 4.2. The previous -mno-sdata
trick is not working anymore.
different versions of FreeBSD source tree.
Old config(8) can now be used unless you want to use INCLUDE_CONFIG_FILE
option.
Approved by: imp
Reviewed by: imp
functions from their origininal place to their own files.
TCP Reassembly from tcp_input.c -> tcp_reass.c
TCP Timewait from tcp_subr.c -> tcp_timewait.c
is caused by my latest changes to config(8). You're supposed to install new
config(8) in order to prevent yourself from seeing a warning about old
version of that tool.
You should configure the kernel with a new config(8) then.
Oked by: rwatson, cognet (mentor)
This patch does the following:
- Remove un-necessary code that is not even compiling into the driver
under TW_OSL_NON_DMA_MEM_ALLOC_PER_REQUEST defines.
- Remove bundled firmware image and associated "files" entry for tw_cl_fwimg.c
- Remove bundled firmware flashing routines. We now have tw_update userspace
FreeBSD controller flash utility.
- Fix driver crash on load due to shared interrupt.
- Fix 2 lock leaks for Giant lock.
- Fix CCB leak.
- Add support for 9650SE controllers.
Many thanks to 3Ware/AMCC for continuing to support FreeBSD.
The entire code is wrapperd in #ifdef ... #endif so it won't harm
the actual implementation, but developers are encouraged to test it.
For arm, ia64, ppc, sparc64 and sun4v some work is still
needed, thus arch maintainers are encouraged to bring their arch on par
with respect to i386 and amd64.
Approved by: re (implicit?)
shared code infrastructure that is family specific and
modular. There is also support for our latest gigabit
nic, the 82575 that is MSI/X and multiqueue capable.
The new shared code changes some interfaces to the core
code but testing at Intel has been going on for months,
it is fairly stable.
I have attempted to be careful in retaining any fixes that
CURRENT had and we did not, I apologize in advance if any
thing gets clobbered, I'm sure I'll hear about it :)
Approved by pdeuskar
calls. Add MAC Framework entry points and MAC policy entry points for
audit(), auditctl(), auditon(), setaudit(), aud setauid().
MAC Framework entry points are only added for audit system calls where
additional argument context may be useful for policy decision-making; other
audit system calls without arguments may be controlled via the priv(9)
entry points.
Update various policy modules to implement audit-related checks, and in
some cases, other missing system-related checks.
Obtained from: TrustedBSD Project
Sponsored by: SPARTA, Inc.
The name trunk is misused as the networking term trunk means carrying multiple
VLANs over a single connection. The IEEE standard for link aggregation (802.3
section 3) does not talk about 'trunk' at all while it is used throughout IEEE
802.1Q in describing vlans.
The lagg(4) driver provides link aggregation, failover and fault tolerance.
Discussed on: current@
Linux SCSI SG passthrough device API. The intention is to allow for both
running of Linux apps that want to talk to /dev/sg* nodes, and to facilitate
porting of apps from Linux to FreeBSD. As such, both native and linuxolator
entry points and definitions are provided.
Caveats:
- This does not support the procfs and sysfs nodes that the Linux SG
driver provides. Some Linux apps may rely on these for operation,
others may only use them for informational purposes.
- More ioctls need to be implemented.
- Linux uses a naming scheme of "sg[a-z]" for devices, while FreeBSD uses a
scheme of "sg[0-9]". Devfs aliasis (symlinks) are automatically created
to link the two together. However, tools like camcontrol only see the
native names.
- Some operations were originally designed to return byte counts or other
data directly as the syscall return value. The linuxolator doesn't appear
to support this well, so this driver just punts for these cases.
Now that the driver is in place, others are welcome to add missing
functionality. Thanks to Roman Divacky for pushing this work along.
When the linux port changes were imported which split the
target command list to be separate from the initiator command
list and the handle format changed to encode a type in the handle
the implications to the function isp_handle_index (which only
the NetBSD/OpenBSD/FreeBSD ports use) were overlooked.
The fault is twofold: first, the index into the DMA maps
in isp_pci is wrong because a target command handle with
the type bit left in place caused a bad index (and panic)
into dma map. Secondly, the assumption of the array
of DMA maps in either PCS or SBUS attachment structures is
that there is a linear mapping between handle index and
DMA map index. This can no longer be true if there are
overlapping index spaces for initiator mode and target
mode commands.
These changes bandaid around the problem by forcing us
to not have simultaneous dual roles and doing the appropriate
masking to make sure things are indexed correctly. A longer
term fix is being devloped.
obtaining and releasing shared and exclusive locks. The algorithms for
manipulating the lock cookie are very similar to that rwlocks. This patch
also adds support for exclusive locks using the same algorithm as mutexes.
A new sx_init_flags() function has been added so that optional flags can be
specified to alter a given locks behavior. The flags include SX_DUPOK,
SX_NOWITNESS, SX_NOPROFILE, and SX_QUITE which are all identical in nature
to the similar flags for mutexes.
Adaptive spinning on select locks may be enabled by enabling the
ADAPTIVE_SX kernel option. Only locks initialized with the SX_ADAPTIVESPIN
flag via sx_init_flags() will adaptively spin.
The common cases for sx_slock(), sx_sunlock(), sx_xlock(), and sx_xunlock()
are now performed inline in non-debug kernels. As a result, <sys/sx.h> now
requires <sys/lock.h> to be included prior to <sys/sx.h>.
The new kernel option SX_NOINLINE can be used to disable the aforementioned
inlining in non-debug kernels.
The size of struct sx has changed, so the kernel ABI is probably greatly
disturbed.
MFC after: 1 month
Submitted by: attilio
Tested by: kris, pjd
other C files:
- Move sbcreatecontrol() and sbtoxsockbuf() to uipc_sockbuf.c. While
sbcreatecontrol() is really an mbuf allocation routine, it does its work
with awareness of the layout of socket buffer memory.
- Move pru_*() protocol switch stubs to uipc_socket.c where the non-stub
versions of several of these functions live. Likewise, move socket state
transition calls (soisconnecting(), etc) to uipc_socket.c. Moveo
sodupsockaddr() and sotoxsocket().
imitating an Ethernet device, so vlan(4) and if_bridge(4) can be
attached to it for testing and benchmarking purposes. Its source
can be an introduction to the anatomy of a network interface driver
due to its simplicity as well as to a bunch of comments in it.
o make all crypto drivers have a device_t; pseudo drivers like the s/w
crypto driver synthesize one
o change the api between the crypto subsystem and drivers to use kobj;
cryptodev_if.m defines this api
o use the fact that all crypto drivers now have a device_t to add support
for specifying which of several potential devices to use when doing
crypto operations
o add new ioctls that allow user apps to select a specific crypto device
to use (previous ioctls maintained for compatibility)
o overhaul crypto subsystem code to eliminate lots of cruft and hide
implementation details from drivers
o bring in numerous fixes from Michale Richardson/hifn; mostly for
795x parts
o add an optional mechanism for mmap'ing the hifn 795x public key h/w
to user space for use by openssl (not enabled by default)
o update crypto test tools to use new ioctl's and add cmd line options
to specify a device to use for tests
These changes will also enable much future work on improving the core
crypto subsystem; including proper load balancing and interposing code
between the core and drivers to dispatch small operations to the s/w
driver as appropriate.
These changes were instigated by the work of Michael Richardson.
Reviewed by: pjd
Approved by: re
- moved away from ifn/ifa access to sctp_ifa/sctp_ifn
built and managed by the add-ip code.
- cleaned up add-ip code to use the iterator
- made iterator be a thread, which enables auto-asconf now.
- rewrote and cleaned up source address selection (also
made it use new structures).
- Fixed a couple of memory leaks.
- DACK now settable as to how many packets to delay as
well as time.
- connectx() to latest socket API, new associd arg.
- Fixed issue with revoking and loosing potential to
send when we inflate the flight size. We now inflate
the cwnd too and deflate it later when the revoked
chunk is sent or acked.
- Got rid of some temp debug code
- src addr selection moved to a common file (sctp_output.c)
- Support for simple VRF's (we have support for multi-vfr
via compile switch that is scrubbed from BSD but we won't
need multi-vrf until we first get VRF :-D)
- Rest of mib work for address information now done
- Limit number of addresses in INIT/INIT-ACK to
a #def (30).
Reviewed by: gnn
sun4v nexus(4) in turn is based on):
o Change nexus(4) to manage the resources of its children so the
respective device drivers don't need to figure them out of OFW
themselves.
o Change nexus(4) to provide the ofw_bus KOBJ interface instead of
using IVARs for supplying the OFW node and the subset of standard
properties of its children. Together with the previous change this
also allows to fully take advantage of newbus in that drivers like
fhc(4), which attach on multiple parent busses, no longer require
different bus front-ends as obtaining the OFW node and properties
as well as resource allocation works the same for all supported
busses. As such this change also is part 4/4 of allowing creator(4)
to work in USIII-based machines as it allows this driver to attach
on both nexus(4) and upa(4). On the other hand removing these IVARs
breaks API compatibility with the powerpc nexus(4) but which isn't
that bad as a) sparc64 currently doesn't share any device driver
hanging off of nexus(4) with powerpc and b) they were no longer
compatible regarding OFW-related extensions at the pci(4) level
since quite some time.
o Provide bus_get_dma_tag methods in nexus(4) and its children in
order to handle DMA tags in a hierarchical way and get rid of the
sparc64_root_dma_tag kludge. Together with the previous two items
this changes also allows to completely get rid of the nexus(4)
IVAR interface. It also includes:
- pushing the constraints previously specified by the nexus_dmatag
down into the DMA tags of psycho(4) and sbus(4) as it's their
IOMMUs which induce these restrictions (and nothing at the
nexus(4) or anything that would warrant specifying them there),
- fixing some obviously wrong constraints of the psycho(4) and
sbus(4) DMA tags, which happened to not actually be used with
the sparc64_root_dma_tag kludge in place and therefore didn't
cause problems so far,
- replacing magic constants for constraints with macros as far
as it is obvious as to where they come from.
This doesn't include taking advantage of the newbus way to get
the parent DMA tags implemented by this change in order to divorce
the IOTSBs of the PCI and SBus IOMMUs or for implementing the
workaround for the DMA sync bug in Sabre (and Tomatillo) bridges,
yet, though.
o Get rid of the notion that nexus(4) (mostly) reflects an UPA bus
by replacing ofw_upa.h and with ofw_nexus.h (which was repo-copied
from ofw_upa.h) and renaming its content, which actually applies to
all of Fireplane/Safari, JBus and UPA (in the host bus case), as
appropriate.
o Just use M_DEVBUF instead of a separate M_NEXUS malloc type for
allocating the device info for the children of nexus(4). This is
done in order to not need to export M_NEXUS when deriving drivers
for subordinate busses from the nexus(4) class.
o Use the DEFINE_CLASS_0() macro to declare the nexus(4) driver so
we can derive subclasses from it.
o Const'ify the nexus_excl_name and nexus_excl_type arrays as well
as add 'associations' and 'rsc', which are pseudo-devices without
resources and therefore of no real interest for nexus(4), to the
former.
o Let the nexus(4) device memory rman manage the entire 64-bit address
space instead of just the UPA_MEMSTART to UPA_MEMEND subregion as
Fireplane/Safari- and JBus-based machines use multiple ranges,
which can't be as easily divided as in the case of UPA (limiting
the address space only served for sanity checking anyway).
o Use M_WAITOK instead of M_NOWAIT when allocating the device info
for children of nexus(4) in order to give one less opportunity
for adding devices to nexus(4) to fail.
o While adapting the drivers affected by the above nexus(4) changes,
change them to take advantage of rman_get_rid() instead of caching
the RIDs assigned to allocated resources, now that the RIDs of
resources are correctly set.
o In iommu(4) and nexus(4) replace hard-coded functions names, which
actually became outdated in several places, in panic strings and
status massages with __func__. [1]
o Use driver_filter_t in prototypes where appropriate.
o Add my copyright to creator(4), fhc(4), nexus(4), psycho(4) and
sbus(4) as I changed considerable amounts of these drivers as well
as added a bunch of new features, workarounds for silicon bugs etc.
o Fix some white space nits.
Due to lack of access to Exx00 hardware, these changes, i.e. central(4)
and fhc(4), couldn't be runtime tested on such a machine. Exx00 are
currently reported to panic before trying to attach nexus(4) anyway
though.
PR: 76052 [1]
Approved by: re (kensmith)
uuencoded format along with their respective LICENSE files.
- Add new share/doc/legal directory to BSD.usr.dist mtree file. This is the
place we install LICENSE files for restricted firmwares.
- Teach firmware(9) and kmod.mk about licensed firmwares. Restricted firmwares
won't load properly unless legal.<name>.license_ack is set to 1, either
via kenv(1) or /boot/loader.conf.
Reviewed by: mlaier, sam
Permitted by: Intel (via Andrew Wilson)
MFC after: 1 month
- Fix missing initialization in kern_rwlock.c causing bogus times to be collected
- Move updates to the lock hash to after the lock is released for spin mutexes,
sleep mutexes, and sx locks
- Add new kernel build option LOCK_PROFILE_FAST - only update lock profiling
statistics when an acquisition is contended. This reduces the overhead of
LOCK_PROFILING to increasing system time by 20%-25% which on
"make -j8 kernel-toolchain" on a dual woodcrest is unmeasurable in terms
of wall-clock time. Contrast this to enabling lock profiling without
LOCK_PROFILE_FAST and I see a 5x-6x slowdown in wall-clock time.
arrangement that has no intrinsic internal knowledge of whether devices
it is given are truly multipath devices. As such, this is a simplistic
approach, but still a useful one.
The basic approach is to (at present- this will change soon) use camcontrol
to find likely identical devices and and label the trailing sector of the
first one. This label contains both a full UUID and a name. The name is
what is presented in /dev/multipath, but the UUID is used as a true
distinguishor at g_taste time, thus making sure we don't have chaos
on a shared SAN where everyone names their data multipath as "Fred".
The first of N identical devices (and N *may* be 1!) becomes the active
path until a BIO request is failed with EIO or ENXIO. When this occurs,
the active disk is ripped away and the next in a list is picked to
(retry and) continue with.
During g_taste events new disks that meet the match criteria for existing
multipath geoms get added to the tail end of the list.
Thus, this active/passive setup actually does work for devices which
go away and come back, as do (now) mpt(4) and isp(4) SAN based disks.
There is still a lot to do to improve this- like about 5 of the 12
recommendations I've received about it, but it's been functional enough
for a while that it deserves a broader test base.
Reviewed by: pjd
Sponsored by: IronPort Systems
MFC: 2 months
It is built in the same module as IPv4 multicast forwarding, i.e. ip_mroute.ko,
if and only if IPv6 support is enabled for loadable modules.
Export IPv6 forwarding structs to userland netstat(1) via sysctl(9).
mapped at, and LOADERRAMADDR, the address at which the loader maps the ram at
at the time the kernel is booted.
They are used to detect if the kernel is booted from the onboard flash.
Define those for the IQ31244
Make PIM dynamically loadable by using encap_attach_func().
PIM may now be loaded into a GENERIC kernel.
Tested with: ports/net/pimdd && tcpreplay && wireshark
Reviewed by: Pavlin Radoslavov
partitioning class that supports multiple schemes. Current
schemes supported are APM (Apple Partition Map) and GPT.
Change all GEOM_APPLE anf GEOM_GPT options into GEOM_PART_APM
and GEOM_PART_GPT (resp).
The ctlreq interface supports verbs to create and destroy
partitioning schemes on a disk; to add, delete and modify
partitions; and to commit or undo changes made.
#ifdef MSDOSFS_LARGE to run-time checks to see if "-o large" was specified.
Test case provided by Oliver Fromme:
truncate -s 200G test.img
mdconfig -a -t vnode -f test.img -u 9
newfs_msdos -s 419430400 -n 1 /dev/md9 zip250
mount -t msdosfs /dev/md9 /mnt # should fail
mount -t msdosfs -o large /dev/md9 /mnt # should succeed
PR: 105964
Requested by: Oliver Fromme <olli lurza secnetix de>
Tested by: trhodes
MFC after: 2 weeks
These are shared-memory variants based on Am79C90-compatible chips
that apart from the missing DMA engine are similar to the 'ledma'
variant including using a (pseudo-)bus/device for the buffer that
the actual LANCE device hangs off from. The performance of these is
close to that of the 'ledma' one, like expected at a few times the
CPU load though.
the newly added DEV_EISA. This is done so that these back-ends can
be compiled on platforms not providing in{b,w,l}()/out{b,w,l}() and
friends (but may wish to use them together with bus front-ends other
than the EISA one).
bus hanging off from the Fireplane/Safari bus in some USIII machines.
This is part 3/4 of allowing creator(4) to work in these machines.
The little info needed on how to configure the bridge and to work
around the incorrect values contained in the `interrupts' properties
of its children were obtained form OpenSolaris.
The separate bus front-end was inherited from the OpenBSD creator(4),
which at that time had a mainbus(4) (for USI/II machines, which use
an UPA interconnection bus as the nexus) and an upa(4) (for USIII
machines, which use a subordinate/slave UPA bus hanging off from the
Fireplane/Safari interconnection bus) front-end. With FreeBSD and
newbus there is/will be no need to have two separate bus front-ends
for these busses, so we can easily coallapse the shared front-end
and the back-end into a single source file (note that the FreeBSD
creator_upa.c was misnomer anyway; based on what it actually attached
to that should have been creator_nexus.c), actually OpenBSD meanwhile
also has moved to a shared front-end and a single source file. Due
to the low-level console support creator.c also wasn't free from bus
related things before.
While at it, also split sys/sparc64/creator/creator.h into a
sys/dev/fb/creatorreg.h that only contains register macros and move
the structures to the top of sys/dev/fb/creator.c as suggested by
style(9) so creator(4) is no longer scattered over two directories.
- Use OF_decode_addr()/sparc64_fake_bustag() to obtain the bus tags and
handles for the low-level console support instead of hardcoding
support for AFB/FFB hanging off from nexus(4) only. This is part 2/4
of allowing creator(4) to work in USIII machines (which have a UPA
bus hanging off from the Fireplane/Safari bus reflected by the nexus),
which already makes it work as the low-level console there.
- Allocate resources in the bus attach routine regardless of whether
creator(4) is used as for the low-level console and thus the required
bus tags and handles have been already obtained or not so the resources
are marked as taken in the respective RMAN.
- For both obtaining the bus tags and handles for the low-level console
support as well as allocating the corresponding resources in the
regular bus attach routine don't bother to get all for the maximum of
24 register banks but only (for) the two tag/handle pairs required for
providing the video interface for syscons(4) support. If we can't
allocate the rest of them just limit the memory range accessible via
creator_fb_mmap() accordingly.
- Sanity check the memory range spanned by the first and last resources
and the resources in between as far as possible, as the XFree86/Xorg
sunffb(4) expects to be able to access the whole region, even though
the backing resources are actually non-continuous. Limit and check
the memory range accessible via creator_fb_mmap() accordingly.
- Reduce the size of buffers for OFW properties to what they actually
need to hold.
- Rename some tables to creator_<foo> for consistency.
- Also for the sizes in the creator_fb_mmap() mapping table entries use
macros for consistency, add macros for the remaining register banks
for completeness.
NOTES though, as ofw_syscons(4) doesn't properly interface with
syscons(4) regarding loading the font specified with SC_DFLT_FONT,
causing a kernel with both options SC_OFWFB and SC_NO_MODE_CHANGE
to not link.
lookup early. This has some performance implications and should not be
enabled by default, but might help greatly in certain setups. After some
more testing this could be turned into a sysctl.
Tested by: avatar
LOR ids: 17, 24, 32, 46, 191 (conceptual)
MFC after: 6 weeks
mac_framework.c Contains basic MAC Framework functions, policy
registration, sysinits, etc.
mac_syscalls.c Contains implementations of various MAC system calls,
including ENOSYS stubs when compiling without options
MAC.
Obtained from: TrustedBSD Project
aches as a read-only file. In a number of cases this has led to
compiles failing- usually due to some strange NFS drift which thinks
that the opt_ah.h in the compile directory is out of date wrt the
source it is copied from. When the copy is executed again, it fails
because the target is read-only. Oops. Modify the compile hooks
avoid this.
Discussed with a while back with: Sam Leffler
just the intenral phy on parts supported by the rl and re drivers, the
RTL8201BL for example. He also sent me a nice picture of hundreds of
these chips in a tray to boulder his claim. :-) Therefore remove a
comment that suggested that they were...
by default for sun4v where it is absolutely required.
This change moves the buffer from struct pcpu to the stack to avoid
using the critical section which created a LOR in a couple of cases
due to interaction with the tty code and kqueue. The LOR can't be
fixed with the critical section and the pcpu buffer can't be used
without the critical section.
Putting the buffer on the stack was my initial solution, but it was
pointed out that the stress on the stack might cause problems
depending on the call path. We don't have a way of creating tests
for those possible cases, so it's best to leave this as an option
for the time being. In time we may get enough data to enable this
option more generally.
way I intended due to licensing restrictions. I had intended
that it would be defaulted on, with opt-out possible for
companies that don't accept the CDDL. The FreeBSD GENERIC
kernel has to be entirely BSD licensed, so the only alternative
would have been to make KDTRACE an opt-in option. That isn't
a design I favour.
- Add a new apic_alloc_vectors() method to the local APIC support code
to allocate N contiguous IDT vectors (aligned on a M >= N boundary).
This function is used to allocate IDT vectors for a group of MSI
messages.
- Add MSI and MSI-X PICs. The PIC code here provides methods to manage
edge-triggered MSI messages as x86 interrupt sources. In addition to
the PIC methods, msi.c also includes methods to allocate and release
MSI and MSI-X messages. For x86, we allow for up to 128 different
MSI IRQs starting at IRQ 256 (IRQs 0-15 are reserved for ISA IRQs,
16-254 for APIC PCI IRQs, and IRQ 255 is reserved).
- Add pcib_(alloc|release)_msi[x]() methods to the MD x86 PCI bridge
drivers to bubble the request up to the nexus driver.
- Add pcib_(alloc|release)_msi[x]() methods to the x86 nexus drivers that
ask the MSI PIC code to allocate resources and IDT vectors.
MFC after: 2 months
wait (time waited to acquire) and hold times for *all* kernel locks. If
the architecture has a system synchronized TSC, the profiling code will
use that - thereby minimizing profiling overhead. Large chunks of profiling
code have been moved out of line, the overhead measured on the T1 for when
it is compiled in but not enabled is < 1%.
Approved by: scottl (standing in for mentor rwatson)
Reviewed by: des and jhb
privilege for threads and credentials. Unlike the existing suser(9)
interface, priv(9) exposes a named privilege identifier to the privilege
checking code, allowing more complex policies regarding the granting of
privilege to be expressed. Two interfaces are provided, replacing the
existing suser(9) interface:
suser(td) -> priv_check(td, priv)
suser_cred(cred, flags) -> priv_check_cred(cred, priv, flags)
A comprehensive list of currently available kernel privileges may be
found in priv.h. New privileges are easily added as required, but the
comments on adding privileges found in priv.h and priv(9) should be read
before doing so.
The new privilege interface exposed sufficient information to the
privilege checking routine that it will now be possible for jail to
determine whether a particular privilege is granted in the check routine,
rather than relying on hints from the calling context via the
SUSER_ALLOWJAIL flag. For now, the flag is maintained, but a new jail
check function, prison_priv_check(), is exposed from kern_jail.c and used
by the privilege check routine to determine if the privilege is permitted
in jail. As a result, a centralized list of privileges permitted in jail
is now present in kern_jail.c.
The MAC Framework is now also able to instrument privilege checks, both
to deny privileges otherwise granted (mac_priv_check()), and to grant
privileges otherwise denied (mac_priv_grant()), permitting MAC Policy
modules to implement privilege models, as well as control a much broader
range of system behavior in order to constrain processes running with
root privilege.
The suser() and suser_cred() functions remain implemented, now in terms
of priv_check() and the PRIV_ROOT privilege, for use during the transition
and possibly continuing use by third party kernel modules that have not
been updated. The PRIV_DRIVER privilege exists to allow device drivers to
check privilege without adopting a more specific privilege identifier.
This change does not modify the actual security policy, rather, it
modifies the interface for privilege checks so changes to the security
policy become more feasible.
Sponsored by: nCircle Network Security, Inc.
Obtained from: TrustedBSD Project
Discussed on: arch@
Reviewed (at least in part) by: mlaier, jmg, pjd, bde, ceri,
Alex Lyashkov <umka at sevcity dot net>,
Skip Ford <skip dot ford at verizon dot net>,
Antoine Brodin <antoine dot brodin at laposte dot net>
work is not just mine, but it is also the works of Peter Lei
and Michael Tuexen. They both are my two key other developers
working on the project.. and they need ata-boy's too:
****
peterlei@cisco.comtuexen@fh-muenster.de
****
I did do a make sysent which updated the
syscall's and sysproto.. I hope that is correct... without
it you don't build since we have new syscalls for SCTP :-0
So go out and look at the NOTES, add
option SCTP (make sure inet and inet6 are present too)
and play with SCTP.
I will see about comitting some test tools I have after I
figure out where I should place them. I also have a
lib (libsctp.a) that adds some of the missing socketapi
functions that I need to put into lib's.. I will talk
to George about this :-)
There may still be some 64 bit issues in here, none of
us have a 64 bit processor to test with yet.. Michael
may have a MAC but thats another beast too..
If you have a mac and want to use SCTP contact Michael
he maintains a web site with a loadable module with
this code :-)
Reviewed by: gnn
Approved by: gnn
as we have no use for that info. Instead let this function return the
keyboard ID and verify at its invocation in sunkbd_configure() that we're
talking to a Sun type 4/5/6 keyboard, i.e. a keyboard supported by this
driver.
- Add an option SUNKBD_EMULATE_ATKBD whose code is based on the respective
code in ukbd(4) and like UKBD_EMULATE_ATSCANCODE causes this driver to
emit AT keyboard/KB_101 compatible scan codes in K_RAW mode as assumed by
kbdmux(4). Unlike UKBD_EMULATE_ATSCANCODE, SUNKBD_EMULATE_ATKBD also
triggers the use of AT keyboard maps and thus allows to use the map files
in share/syscons/keymaps with this driver at the cost of an additional
translation (in ukbd(4) this just is the way of operation).
- Implement an option SUNKBD_DFLT_KEYMAP, which like the equivalent options
of the other keyboard drivers allows to specify the default in-kernel
keyboard map. For obvious reasons this made to only work when also using
SUNKBD_EMULATE_ATKBD.
- Implement sunkbd_check(), sunkbd_check_char() and sunkbd_clear_state(),
which are also required for interoperability with kbdmux(4).
- Implement K_CODE mode and FreeBSD keypad compose.
- As a minor hack define KBD_DFLT_KEYMAP also in the !SUNKBD_EMULATE_ATKBD
case so we can obtain fkey_tab from <dev/kbd/kbdtables.h> rather than
having to duplicate it and #ifdef some more code.
- Don't use the TX-buffer for writing the two command bytes for setting the
keyboard LEDs as this consequently requires a hardware FIFO that is at
least two bytes in depth, which the NMOS-variant of the Zilog SCCs doesn't
have. Thus use an inlined version of uart_putc() to consecutively write
the command bytes (a cleaner approach would be to do this via the soft
interrupt handler but that variant wouldn't work while in ddb(4)). [1]
- Fix some minor style(9) bugs.
PR: 90316 [1]
Reviewed by: marcel [1]
dynamic nature (if no native aio code is available, the linux part
returns ENOSYS because of missing requisites) should be solved differently
than it is.
All this will be done in P4.
Not included in this commit is a backout of the changes to the native aio
code (removing static in some places). Those changes (and some more) will
also be needed when the reworked linux aio stuff will reenter the tree.
Requested by: rwatson
Discussed with: rwatson
i386). Use -mprofiler-epilogue again, and don't use -finstrument-functions.
The former has been fixed for arches that implement high-res profiling,
and the latter has been useless for kernel profiling since gcc-3.4
when it started forcing -fno-inline. -fno-inline gives a kernel with
performance characteristics too different from a normal kernel to be
worth profiling, by turning off inlining of all the little optimized
functions in headers. This interacts especially badly with FreeBSD's
use of "static inline" for all inlines in headers, by creating many
separate copies of the little functions, so not inlining tends to
increase cache pressure where it should reduce it, and (since gprof(1)
doesn't understand the copies) the statistics for the little functions
are hard to interpret even if you want them.
to and from struct timespec, to replace the crummy conversion
function which have been copy&pasted into three different
filesystems already.
Apart from general crummyness as indicated by code like:
for (year = 1970;; year++) {
inc = year & 0x03 ? 365 : 366;
if (days < inc)
break;
days -= inc;
}
They also contain specialized crummyness which tries to compensate
for the general crummyness by caching recent conversion results,
with no regard for locking or consistency.
These replacement functions are smaller, O(1) and handle the Y2.1K
leap-year correctly.
Ideally, these functions should live in a module of their own,
which the three offending filesystems would depend on, but the
size is 877 bytes of code (on i386), so that would be false
economy.
should be easily adapted to SD 2.0 (aka SDHC), SDIO, MMC and MMCplus
cards. At the present time, there's only one bridge driver for the
ARM9 based Atmel AT91RM9200.
snd_emu10k1 and snd_emu10kx into one line. The 'pci' dependency here
adds no value, so I eliminted it (we don't have a snd.all file that
might make it mildly useful, and even then it wouldn't be that
useful). With the pci optional component eliminated, I could use the
'|' operator. I could have also include pci on both sides of the |
operator, but since it isn't a value add at all, it was better to
eliminate it.
Implement the linux_io_* syscalls (AIO). They are only enabled if the native
AIO code is available (either compiled in to the kernel or as a module) at
the time the functions are used. If the AIO stuff is not available there
will be a ENOSYS.
From the submitter:
---snip---
DESIGN NOTES:
1. Linux permits a process to own multiple AIO queues (distinguished by
"context"), but FreeBSD creates only one single AIO queue per process.
My code maintains a request queue (STAILQ of queue(3)) per "context",
and throws all AIO requests of all contexts owned by a process into
the single FreeBSD per-process AIO queue.
When the process calls io_destroy(2), io_getevents(2), io_submit(2) and
io_cancel(2), my code can pick out requests owned by the specified context
from the single FreeBSD per-process AIO queue according to the per-context
request queues maintained by my code.
2. The request queue maintained by my code stores contrast information between
Linux IO control blocks (struct linux_iocb) and FreeBSD IO control blocks
(struct aiocb). FreeBSD IO control block actually exists in userland memory
space, required by FreeBSD native aio_XXXXXX(2).
3. It is quite troubling that the function io_getevents() of libaio-0.3.105
needs to use Linux-specific "struct aio_ring", which is a partial mirror
of context in user space. I would rather take the address of context in
kernel as the context ID, but the io_getevents() of libaio forces me to
take the address of the "ring" in user space as the context ID.
To my surprise, one comment line in the file "io_getevents.c" of
libaio-0.3.105 reads:
Ben will hate me for this
REFERENCE:
1. Linux kernel source code: http://www.kernel.org/pub/linux/kernel/v2.6/
(include/linux/aio_abi.h, fs/aio.c)
2. Linux manual pages: http://www.kernel.org/pub/linux/docs/manpages/
(io_setup(2), io_destroy(2), io_getevents(2), io_submit(2), io_cancel(2))
3. Linux Scalability Effort: http://lse.sourceforge.net/io/aio.html
The design notes: http://lse.sourceforge.net/io/aionotes.txt
4. The package libaio, both source and binary:
http://rpmfind.net/linux/rpm2html/search.php?query=libaio
Simple transparent interface to Linux AIO system calls.
5. Libaio-oracle: http://oss.oracle.com/projects/libaio-oracle/
POSIX AIO implementation based on Linux AIO system calls (depending on
libaio).
---snip---
Submitted by: Li, Xiao <intron@intron.ac>
unsuspecting users.
- Add a comment in NOTES about experimental status of SCHED_ULE.
- Make warning about experimental status in sched_ule(4) a bit
stronger.
Suggested and reviewed by: dougb
Discussed on: developers
MFC after: 3 days
Split subr_clock.c in two parts (by repo-copy):
subr_clock.c contains generic RTC and calendaric stuff. etc.
subr_rtc.c contains the newbus'ified RTC interface.
Centralize the machdep.{adjkerntz,disable_rtc_set,wall_cmos_clock}
sysctls and associated variables into subr_clock.c. They are
not machine dependent and we have generic code that relies on being
present so they are not even optional.
Add support for Intel High Definition Audio Controller.
This driver make a special guarantee that "playback" works
on majority hardwares with minimal or without specific vendor
quirk.
This driver is a product of collaborative effort made by:
Stephane E. Potvin <sepotvin@videotron.ca>
Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Wesley Morgan <morganw@chemikals.org>
Daniel Eischen <deischen@FreeBSD.org>
Maxime Guillaud <bsd-ports@mguillaud.net>
Ariff Abdullah <ariff@FreeBSD.org>
....and various people from freebsd-multimedia@FreeBSD.org
Refer to snd_hda(4) for features and issues.
Welcome To HDA.
Sponsored by: Defenxis Sdn. Bhd.
With the first part of my previous Summer of Code work, we get:
-made libalias modular:
-support for 'particular' protocols (like ftp/irc/etcetc) is no more
hardcoded inside libalias, but it's available through external
modules loadable at runtime
-modules are available both in kernel (/boot/kernel/alias_*.ko) and
user land (/lib/libalias_*)
-protocols/applications modularized are: cuseeme, ftp, irc, nbt, pptp,
skinny and smedia
-added logging support for kernel side
-cleanup
After a buildworld, do a 'mergemaster -i' to install the file libalias.conf
in /etc or manually copy it.
During startup (and after every HUP signal) user land applications running
the new libalias will try to read a file in /etc called libalias.conf:
that file contains the list of modules to load.
User land applications affected by this commit are ppp and natd:
if libalias.conf is present in /etc you won't notice any difference.
The only kernel land bit affected by this commit is ng_nat:
if you are using ng_nat, and it doesn't correctly handle
ftp/irc/etcetc sessions anymore, remember to kldload
the correspondent module (i.e. kldload alias_ftp).
General information and details about the inner working are available
in the libalias man page under the section 'MODULAR ARCHITECTURE
(AND ipfw(4) SUPPORT)'.
NOTA BENE: this commit affects _ONLY_ libalias, ipfw in-kernel nat
support will be part of the next libalias-related commit.
Approved by: glebius
Reviewed by: glebius, ru
- Split out the communication protocols into their own files and use
a couple of function pointers in the softc that the commuication
protocols setup in their own attach routine.
- Add support for the SSIF interface (talking to IPMI over SMBus).
- Add an ACPI attachment.
- Add a PCI attachment that attaches to devices with the IPMI interface
subclass.
- Split the ISA attachment out into its own file: ipmi_isa.c.
- Change the code to probe the SMBIOS table for an IPMI entry to just use
pmap_mapbios() to map the table in rather than trying to setup a fake
resource on an isa device and then activating the resource to map in the
table.
- Make bus attachments leaner by adding attach functions for each
communication interface (ipmi_kcs_attach(), ipmi_smic_attach(), etc.)
that setup per-interface data.
- Formalize the model used by the driver to handle requests by adding an
explicit struct ipmi_request object that holds the state of a given
request and reply for the entire lifetime of the request. By bundling
the request into an object, it is easier to add retry logic to the various
communication backends (as well as eventually support BT mode which uses
a slightly different message format than KCS, SMIC, and SSIF).
- Add a per-softc lock and remove D_NEEDGIANT as the driver is now MPSAFE.
- Add 32-bit compatibility ioctl shims so you can use a 32-bit ipmitool
on FreeBSD/amd64.
- Add ipmi(4) to i386 and amd64 NOTES.
Submitted by: ambrisko (large portions of 2 and 3)
Sponsored by: IronPort Systems, Yahoo!
MFC after: 6 days
other problems while labels were first being added to various kernel
objects. They have outlived their usefulness.
MFC after: 1 month
Suggested by: Christopher dot Vance at SPARTA dot com
Obtained from: TrustedBSD Project
part of the hal distribution early on when the hal was built for
each os but it's been portable for a long time so move the os-specific
code out (and off the vendor branch)
o correct the copyright on ah_osdep.?; it was mistakenly given a
restricted license and not a dual-bsd/gpl license
o remove the module api definition as it was never used
o fixup include paths for move of ah_osdep.h
MFC after: 2 weeks
in older versions of FreeBSD. This option is pointless as it is needed in just
about every interesting usage of forward that I have ever seen. It doesn't make
the system any safer and just wastes huge amounts of develper time
when the system doesn't behave as expected when code is moved from
4.x to 6.x It doesn't make
the system any safer and just wastes huge amounts of develper time
when the system doesn't behave as expected when code is moved from
4.x to 6.x or 7.x
Reviewed by: glebius
MFC after: 1 week
- TLS - complete
- pid/tid mangling - complete
- thread area - complete
- futexes - complete with issues
- clone() extension - complete with some possible minor issues
- mq*/timer*/clock* stuff - complete but untested and the mq* stuff is
disabled when not build as part of the kernel with native FreeBSD mq*
support (module support for this will come later)
Tested with:
- linux-firefox - works, tested
- linux-opera - works, tested
- linux-realplay - doesnt work, issue with futexes
- linux-skype - doesnt work, issue with futexes
- linux-rt2-demo - works, tested
- linux-acroread - doesnt work, unknown reason (coredump) and sometimes
issue with futexes
- various unix utilities in linux-base-gentoo3 and linux-base-fc4:
everything tried worked
On amd64 not everything is supported like on i386, the catchup is planned for
later when the remaining bugs in the new functions are fixed.
To test this new stuff, you have to run
sysctl compat.linux.osrelease=2.6.16
to switch back use
sysctl compat.linux.osrelease=2.4.2
Don't switch while running a linux program, strange things may or may not
happen.
Sponsored by: Google SoC 2006
Submitted by: rdivacky
Some suggestions/help by: jhb, kib, manu@NetBSD.org, netchild
serial line usb drivers that depend on it. Instead, let the compile
fail rather than silently not including the driver. This is more in
line with how we handle things like mii.
# I'll note: a better system for coping with missing depends is needed,
# but this dependency is clearly backwards given our current flawed
# depend system.
whole the physical memory, cached, using 1MB section mappings. This reduces
the address space available for user processes a bit, but given the amount of
memory a typical arm machine has, it is not (yet) a big issue.
It then provides a uma_small_alloc() that works as it does for architectures
which have a direct mapping.
uipc_proto.c to uipc_usrreq.c, making localdomain static. Remove
uipc_proto.c as it's no longer used. With this change, UNIX domain
sockets are entirely encapsulated in uipc_usrreq.c.
PowerPC-based Apple's machines and small utility to do it from
userland modelled after the similar utility in Darwin/OSX.
Only tested on 1.25GHz G4 Mac Mini.
MFC after: 1 month
and pc98 MD files. Remove nodevice and nooption lines specific
to sio(4) from ia64, powerpc and sparc64 NOTES. There were no
such lines for arm yet.
sio(4) is usable on less than half the platforms, not counting
a future mips platform. Its presence in MI files is therefore
increasingly becoming a burden.
implementations and adjust some of the checks while I'm here:
- Add a new check to make sure we don't return from a syscall in a critical
section.
- Add a new explicit check before userret() to make sure we don't return
with any locks held. The advantage here is that we can include the
syscall number and name in syscall() whereas that info is not available
in userret().
- Drop the mtx_assert()'s of sched_lock and Giant. They are replaced by
the more general checks just added.
MFC after: 2 weeks
