is finished with it; this may only occur when the tx queue is setup as
dba-gated but since the fix is cheap apply it to all queues
while here make the queue depth signed for use in assertions
Reviewed by: apatti
MFC after: 2 weeks
Return BUS_PROBE_LOW_PRIORITY for a successful probe. This is in
preparation of the introduction of scc(4), which is going to handle
SCCs in the near future.
mutex.
- Don't use callout_drain() to stop the toffhandle callout while holding the
fdc mutex (this could deadlock) in functions called from softclock
(callouts aren't allowed to do voluntary sleeps). Instead, use
callout_stop(). Note that since we hold the associated mutex and are now
using callout_init_mtx(), callout_stop() is just as effective as
callout_drain(). (Though callout_drain() is still needed in detach to
make sure softclock isn't contesting on our mutex before we destroy the
mutex.)
- Remove unused callout 'tohandle' from softc.
MFC after: 1 week
interrupt handlers rather than BUS_SETUP_INTR() and BUS_TEARDOWN_INTR().
Uses of the BUS_*() versions in the implementation of foo_intr methods
in bus drivers were not changed. Mostly this just means that some
drivers might start printing diagnostic messages like [FAST] when
appropriate as well as honoring mpsafenet=0.
- Fix two more of the ppbus drivers' identify routines to function
correctly in the mythical case of a machine with more than one ppbus.
processing the interrupt events. If we clear them afterwards we
can completely miss some events as the NIC can change the source
flags while we're in the handler. In order to not get another
interrupt while we're in ifp->if_input() with the driver lock
dropped we now turn off NIC interrupts while in the interrupt
handler. Previously this was meant to be achieved by clearing the
interrupt source flags after processing the interrupt events but
didn't really work as clearing these flags doesn't actually
acknowledge and re-enable the events.
This fixes the device timeouts seen with the VMware LANCE.
- Relax the watchdog timer somewhat; don't enable it until the last
packet is enqueued and if there is a TX interrupt but there are
still outstanding ones reload the timer.
Reported and tested by: Morten Rodal <morten@rodal.no>
MFC after: 3 days
The ed driver on pc98 was broken by if_edvar.h rev1.31.
Reported by: Kaho Toshikazu (kaho at elam kais kyoto-u ac jp)
Tested by: Eiji Kato (ekato at a1 mbn or jp)
MFC after: 3 days
More info regarding these nics can be found at http://www.myri.com.
Please note that the files
sys/dev/myri10ge/{mcp_gen_header.h,myri10ge_mcp.h} are internally
shared between all our drivers (solaris, macosx, windows, linux, etc).
I'd like to keep these files unchanged, so I can just import newer
versions of them when the firmware API/ABI changes. This means I'm
stuck with some of the crazy-long #define names, and possibly
non-style(9) characteristics of these files.
Many thanks to mlaier for doing firmware(9) just as I
needed it, and to scottl for his helpful review.
Reviewed by: scottl, glebius
Sponsored by: Myricom Inc.
forcing DMA alignment to default buffer size.
- Make sure DMA pointer properly aligned to avoid being truncated by caller
which causing severe underruns and random popping (especially in 32bit
playback / recording).
- Add AC97 inverted external amplifier quirk for Maxselect x710s
- http://maxselect.ru/
MFC after: 1 week
the SMI/TCO address space. Switch the bus space I/O to the
one specific for either the SMI or TCO space. Re-calibrate
the tick. Add some more device id's, 82801FBR submitted by des.
This makes it work on the platforms I've tested with.
Go ahead by: des
should fix strange link state behaviour reported for bcm5721 & bcm5704c
2) Clear bge_link flag in bge_stop()
3) Force link state check after bge_ifmedia_upd(). Otherwise we can miss link
event if PHY changes it's state fast enough.
Tested by: phk (bcm5704c)
Approved by: glebius (mentor)
MFC after: 1 week
Acknowledgement should definitly go to JMicron Technology for providing full
docs on the metadata format as the only vendor so far, big thanks from here.
- In em_attach() remove em_check_for_link(). Not needed here, since
already done in em_hardware_init().
- In em_attach() replace the printing block with call to
em_update_link_status().
- Remove modification of sc->link_state from em_hardware_init() and
from em_media_status(). This makes em_update_link_status() a
single point of change. Call em_update_link_status() where needed.
