It is not listed in the boot sequence in the MP specification (1.4),
and it is explicitly ignored on modern CPUs. It was only ever required
when bootstrapping systems with external APICs (that is, SMP machines
with 486s), which FreeBSD has never supported (and never will).
While here, tidy some comments and remove some banal ones.
matches the algorithm in the MP specification (1.4). Previously we
were sending out the deassert INIT IPI immediately after the initial
INIT IPI was sent.
from pmap_pte(). PT_SET_MA() is not a queued mapping update, but instead
an immediate mapping update, so the page queues lock is not required here.
Reviewed by: cperciva
on x86 and use that to implement stop_emulating() in the fpu/npx code.
Reimplement start_emulating() in the non-XEN case by using load_cr0() and
rcr0() instead of the 'lmsw' and 'smsw' instructions. Intel explicitly
discourages the use of 'lmsw' and 'smsw' on 80386 and later processors in
the description of these instructions in Volume 2 of the ADM.
Reviewed by: kib
MFC after: 1 month
trampoline addresses after the shared page is enabled. Handle FreeBSD
ABIs without shared page support too.
Reported and tested by: David Wolfskill <david catwhisker org>
(previous version)
Pointy hat to: kib
MFC after: 1 month
usermode, using shared page. The structures and functions have vdso
prefix, to indicate the intended location of the code in some future.
The versioned per-algorithm data is exported in the format of struct
vdso_timehands, which mostly repeats the content of in-kernel struct
timehands. Usermode reading of the structure can be lockless.
Compatibility export for 32bit processes on 64bit host is also
provided. Kernel also provides usermode with indication about
currently used timecounter, so that libc can fall back to syscall if
configured timecounter is unknown to usermode code.
The shared data updates are initiated both from the tc_windup(), where
a fast task is queued to do the update, and from sysctl handlers which
change timecounter. A manual override switch
kern.timecounter.fast_gettime allows to turn off the mechanism.
Only x86 architectures export the real algorithm data, and there, only
for tsc timecounter. HPET counters page could be exported as well, but
I prefer to not further glue the kernel and libc ABI there until
proper vdso-based solution is developed.
Minimal stubs neccessary for non-x86 architectures to still compile
are provided.
Discussed with: bde
Reviewed by: jhb
Tested by: flo
MFC after: 1 month
- Stateful TCP offload drivers for Terminator 3 and 4 (T3 and T4) ASICs.
These are available as t3_tom and t4_tom modules that augment cxgb(4)
and cxgbe(4) respectively. The cxgb/cxgbe drivers continue to work as
usual with or without these extra features.
- iWARP driver for Terminator 3 ASIC (kernel verbs). T4 iWARP in the
works and will follow soon.
Build-tested with make universe.
30s overview
============
What interfaces support TCP offload? Look for TOE4 and/or TOE6 in the
capabilities of an interface:
# ifconfig -m | grep TOE
Enable/disable TCP offload on an interface (just like any other ifnet
capability):
# ifconfig cxgbe0 toe
# ifconfig cxgbe0 -toe
Which connections are offloaded? Look for toe4 and/or toe6 in the
output of netstat and sockstat:
# netstat -np tcp | grep toe
# sockstat -46c | grep toe
Reviewed by: bz, gnn
Sponsored by: Chelsio communications.
MFC after: ~3 months (after 9.1, and after ensuring MFC is feasible)
layer, but it is read directly by the MI VM layer. This change introduces
pmap_page_is_write_mapped() in order to completely encapsulate all direct
access to PGA_WRITEABLE in the pmap layer.
Aesthetics aside, I am making this change because amd64 will likely begin
using an alternative method to track write mappings, and having
pmap_page_is_write_mapped() in place allows me to make such a change
without further modification to the MI VM layer.
As an added bonus, tidy up some nearby comments concerning page flags.
Reviewed by: kib
MFC after: 6 weeks
- Remove cpuset stopped_cpus which is no longer used.
- Add a short comment for cpuset suspended_cpus clearing.
- Fix the un-ordered x86/acpica/acpi_wakeup.c in conf/files.amd64 and i386.
Pointed-out by: attilio@
suspend/resume procedures are minimized among them.
common:
- Add global cpuset suspended_cpus to indicate APs are suspended/resumed.
- Remove acpi_waketag and acpi_wakemap from acpivar.h (no longer used).
- Add some variables in acpi_wakecode.S in order to minimize the difference
among amd64 and i386.
- Disable load_cr3() because now CR3 is restored in resumectx().
amd64:
- Add suspend/resume related members (such as MSR) in PCB.
- Modify savectx() for above new PCB members.
- Merge acpi_switch.S into cpu_switch.S as resumectx().
i386:
- Merge(and remove) suspendctx() into savectx() in order to match with
amd64 code.
Reviewed by: attilio@, acpi@
Constify pc_freemask[].
pmap_pv_reclaim()
Eliminate "freemask" because it was a pessimization. Add a comment about
the resident count adjustment.
free_pv_entry() [i386 only]
Merge an optimization from amd64 (r233954).
get_pv_entry()
Eliminate the move to tail of the pv_chunk on the global pv_chunks list.
(The right strategy needs more thought. Moreover, there were unintended
differences between the amd64 and i386 implementation.)
pmap_remove_pages()
Eliminate unnecessary ()'s.
locked xchg instruction. IA32 memory model guarantees that store has
release semantic, since stores cannot pass loads or stores.
Reviewed by: bde, jhb
Tested by: pho
MFC after: 2 weeks
(described in ACPICA source code).
- Move intr_disable() and intr_restore() from acpi_wakeup.c to acpi.c
and call AcpiLeaveSleepStatePrep() in interrupt disabled context.
- Add acpi_wakeup_machdep() to execute wakeup MD procedures and call
it twice in interrupt disabled/enabled context (ia64 version is
just dummy).
- Rename wakeup_cpus variable in acpi_sleep_machdep() to suspcpus in
order to be shared by acpi_sleep_machdep() and acpi_wakeup_machdep().
- Move identity mapping related code to acpi_install_wakeup_handler()
(i386 version) for preparation of x86/acpica/acpi_wakeup.c
(MFC candidate).
Reviewed by: jkim@
MFC after: 2 days
longer uses the active and inactive paging queues. Instead, the pmap now
maintains an LRU-ordered list of pv entry pages, and pmap_pv_reclaim() uses
this list to select pv entries for reclamation.
Note: The old pmap_collect() tried to avoid reclaiming mappings for pages
that have either a hold_count or a busy field that is non-zero. However,
this isn't necessary for correctness, and the locking in pmap_collect() was
insufficient to guarantee that such mappings weren't reclaimed. The new
pmap_pv_reclaim() doesn't even try.
Tested by: sbruno
MFC after: 5 weeks
to this pmap.c. This new r/w lock is used primarily to synchronize access
to the PV lists. However, it will be used in a somewhat unconventional
way. As finer-grained PV list locking is added to each of the pmap
functions that acquire this r/w lock, its acquisition will be changed from
write to read, enabling concurrent execution of the pmap functions with
finer-grained locking.
X-MFC after: r236045
longer uses the active and inactive paging queues. Instead, the pmap now
maintains an LRU-ordered list of pv entry pages, and pmap_pv_reclaim() uses
this list to select pv entries for reclamation.
Note: The old pmap_collect() tried to avoid reclaiming mappings for pages
that have either a hold_count or a busy field that is non-zero. However,
this isn't necessary for correctness, and the locking in pmap_collect() was
insufficient to guarantee that such mappings weren't reclaimed. The new
pmap_pv_reclaim() doesn't even try.
MFC after: 5 weeks
in_cksum.h required ip.h to be included for struct ip. To be
able to use some general checksum functions like in_addword()
in a non-IPv4 context, limit the (also exported to user space)
IPv4 specific functions to the times, when the ip.h header is
present and IPVERSION is defined (to 4).
We should consider more general checksum (updating) functions
to also allow easier incremental checksum updates in the L3/4
stack and firewalls, as well as ponder further requirements by
certain NIC drivers needing slightly different pseudo values
in offloading cases. Thinking in terms of a better "library".
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
Reviewed by: gnn (as part of the whole)
MFC After: 3 days
With the changes over the past year to how accesses to the page's dirty
field are synchronized, there is no need for pmap_protect() to acquire
the page queues lock unless it is going to access the pv lists or
PMAP1/PADDR1.
Style fix to pmap_protect().
Most part is merged from amd64.
- i386/acpica/acpi_wakecode.S
Replaced with amd64 code (from realmode to paging enabling code).
- i386/acpica/acpi_wakeup.c
Replaced with amd64 code (except for wakeup_pagetables stuff).
- i386/include/pcb.h
- i386/i386/genassym.c
Added PCB new members (CR0, CR2, CR4, DS, ED, FS, SS, GDT, IDT, LDT
and TR) needed for suspend/resume, not for context switch.
- i386/i386/swtch.s
Added suspendctx() and resumectx().
Note that savectx() was not changed and used for suspending (while
amd64 code uses it).
BSP and AP execute the same sequence, suspendctx(), acpi_wakecode()
and resumectx() for suspend/resume (in case of UP system also).
- i386/i386/apic_vector.s
Added cpususpend().
- i386/i386/mp_machdep.c
- i386/include/smp.h
Added cpususpend_handler().
- i386/include/apicvar.h
- kern/subr_smp.c
- sys/smp.h
Added IPI_SUSPEND and suspend_cpus().
- i386/i386/initcpu.c
- i386/i386/machdep.c
- i386/include/md_var.h
- pc98/pc98/machdep.c
Moved initializecpu() declarations to md_var.h.
MFC after: 3 days
ataraid(4) previously was present there and having GEOM RAID is convinient.
Unlike other classes GEOM RAID can be set up from BIOS before install and
users are expecting it to be detected automatically.
- DTrace scripts to check for errors, performance, ...
they serve mostly as examples of what you can do with the static probe;s
with moderate load the scripts may be overwhelmed, excessive lock-tracing
may influence program behavior (see the last design decission)
Design decissions:
- use "linuxulator" as the provider for the native bitsize; add the
bitsize for the non-native emulation (e.g. "linuxuator32" on amd64)
- Add probes only for locks which are acquired in one function and released
in another function. Locks which are aquired and released in the same
function should be easy to pair in the code, inter-function
locking is more easy to verify in DTrace.
- Probes for locks should be fired after locking and before releasing to
prevent races (to provide data/function stability in DTrace, see the
man-page of "dtrace -v ..." and the corresponding DTrace docs).
intr_bind() on x86.
This has been requested by jhb and I strongly disagree with this,
but as long as he is the x86 and interrupt subsystem maintainer I will
follow his directives.
The disagreement cames from what we should really consider as a
public KPI. IMHO, if we really need a selection between the kernel
functions, we may need an explicit protection like _KERNEL_KPI, which
defines which subset of the kernel function might really be considered
as part of the KPI (for thirdy part modules) and which not.
As long as we don't have this mechanism I just consider any possible
function as usable by thirdy part code, thus intr_bind() included.
MFC after: 1 week
discrepancy between modules and kernel, but deal with SMP differences
within the functions themselves.
As an added bonus this also helps in terms of code readability.
Requested by: gibbs
Reviewed by: jhb, marius
MFC after: 1 week
but GNU libc used it without checking its kernel version, e. g., Fedora 10.
- Move pipe(2) implementation for Linuxulator from MD files to MI file,
sys/compat/linux/linux_file.c. There is no MD code for this syscall at all.
- Correct an argument type for pipe() from l_ulong * to l_int *. Probably
this was the source of MI/MD confusion.
Reviewed by: emulation
push the address onto stack as we do for INTn emulation. This avoids stack
underflow when we encounter RETF instruction in VM86 mode. Lack of this
exit point actually caused page fault in VM86 mode with VESA module when we
resume from suspend state[1].
- Remove unnecessary CLI and STI instructions from BIOS interrupt emulation.
INTn and IRET must be able to emulate the flag correctly.
Reported by: gavin [1]
Tested by: gavin (early revision)
MFC after: 3 days
- Mark 'sdp' as requiring 'inet'.
- Always include "opt_inet.h" and "opt_inet6.h" and modify the IB
driver Makefiles to honor WITH/WITHOUT_INET/INET6/_SUPPORT options
to determine what should be enabled during a module build.
- Fix the mlxen(4) driver and the core IB code to compile without
if INET is disabled (including when both INET and INET6 are disabled).
Reviewed by: bz
MFC after: 2 weeks
in set_apic_interrupt_ids(). Besides, set_apic_interrupts_ids() is not
called in the !SMP case too.
Fix this by:
- Adding the BSP as an interrupt target directly in cpu_startup().
- Remove an obsolete optimization where the BSP are skipped in
set_apic_interrupt_ids().
Reported by: jh
Reviewed by: jhb
MFC after: 3 days
X-MFC: r233961
Pointy hat to: me
an uncorrected ECC error tends to fire on all CPUs in a package
simultaneously and the current printf hacks are not sufficient to make
the messages legible. Instead, use the existing mca_lock spinlock to
serialize calls to mca_log() and change the machine check code to panic
directly when an unrecoverable error is encoutered rather than falling
back to a trap_fatal() call in trap() (which adds nearly a screen-full of
logging messages that aren't useful for machine checks).
MFC after: 2 weeks
bridges. Rather than blindly enabling the windows on all of them, only
enable the window when an MSI interrupt is enabled for a device behind
the bridge, similar to what already happens for HT PCI-PCI bridges.
To implement this, each x86 Host-PCI bridge driver has to be able to
locate it's actual backing device on bus 0. For ACPI, use the _ADR
method to find the slot and function of the device. For the non-ACPI
case, the legacy(4) driver already scans bus 0 looking for Host-PCI
bridge devices. Now it saves the slot and function of each bridge that
it finds as ivars that the Host-PCI bridge driver can then use in its
pcib_map_msi() method.
This fixes machines where non-MSI interrupts were broken by the previous
round of HT MSI changes.
Tested by: bapt
MFC after: 1 week
be less ambiguous and more clearly identify what it means. This
attribute is what Intel refers to as UC-, and it's only difference
relative to normal UC memory is that a WC MTRR will override a UC-
PAT entry causing the memory to be treated as WC, whereas a UC PAT
entry will always override the MTRR.
- Remove the VM_MEMATTR_UNCACHED alias from powerpc.
New kernel events can be added at various location for sampling or counting.
This will for example allow easy system profiling whatever the processor is
with known tools like pmcstat(8).
Simultaneous usage of software PMC and hardware PMC is possible, for example
looking at the lock acquire failure, page fault while sampling on
instructions.
Sponsored by: NETASQ
MFC after: 1 month
<20120222095239.Horde.0hpYHJjmRSRPRKzXsoFRbYk@webmail.leidinger.net>.
According to some private emails received, it apparently is not unpopular
to use at least Quad GigaSwift cards driven by cas(4) in x86 machines.
MFC after: 1 week
The GPL infected parts which were blocking the inclusion of snd_csa
and snd_emu10kx in GENERIC have recently been removed from the tree.
I'm also adding snd_cmi to GENERIC, which I originally intended to
add when we enabled sound support by default.
Discussed with: jhb, pfg, Yuriy Tsibizov <yuriy.tsibizov@gfk.ru>
Approved by: jhb
kernel.
When access restrictions are added to a page table entry, we flush the
corresponding virtual address mapping from the TLB. In contrast, when
access restrictions are removed from a page table entry, we do not
flush the virtual address mapping from the TLB. This is exactly as
recommended in AMD's documentation. In effect, when access
restrictions are removed from a page table entry, AMD's MMUs will
transparently refresh a stale TLB entry. In short, this saves us from
having to perform potentially costly TLB flushes. In contrast,
Intel's MMUs are allowed to generate a spurious page fault based upon
the stale TLB entry. Usually, such spurious page faults are handled
by vm_fault() without incident. However, when we are executing
no-fault sections of the kernel, we are not allowed to execute
vm_fault(). This change introduces special-case handling for spurious
page faults that occur in no-fault sections of the kernel.
In collaboration with: kib
Tested by: gibbs (an earlier version)
I would also like to acknowledge Hiroki Sato's assistance in
diagnosing this problem.
MFC after: 1 week
As of FreeBSD 8, this driver should not be used. Applications that use
posix_openpt(2) and openpty(3) use the pts(4) that is built into the
kernel unconditionally. If it turns out high profile depend on the
pty(4) module anyway, I'd rather get those fixed. So please report any
issues to me.
The pty(4) module is still available as a kernel module of course, so a
simple `kldload pty' can be used to run old-style pseudo-terminals.
segments.h to a new x86 segments.h.
Add __packed attribute to some structs (just to be sure).
Also make it clear that i386 GDT and LDT entries are used in ia64 code.
excluded from superpage promotions. At least one of the reason is
that pv_table is sized for non-fictitious pages only.
Consistently check for the page to be non-fictitious before accesing
superpage pv list.
Sponsored by: The FreeBSD Foundation
Reviewed by: alc
MFC after: 2 weeks
reg.h with stubs.
The tREGISTER macros are only made visible on i386. These macros are
deprecated and should not be available on amd64.
The i386 and amd64 versions of struct reg have been renamed to struct
__reg32 and struct __reg64. During compilation either __reg32 or __reg64
is defined as reg depending on the machine architecture. On amd64 the i386
struct is also available as struct reg32 which is used in COMPAT_FREEBSD32
code.
Most of compat/ia32/ia32_reg.h is now IA64 only.
Reviewed by: kib (previous version)
Remove FPU types from compat/ia32/ia32_reg.h that are no longer needed.
Create machine/npx.h on amd64 to allow compiling i386 code that uses
this header.
The original npx.h and fpu.h define struct envxmm differently. Both
definitions have been included in the new x86 header as struct __envxmm32
and struct __envxmm64. During compilation either __envxmm32 or __envxmm64
is defined as envxmm depending on machine architecture. On amd64 the i386
struct is also available as struct envxmm32.
Reviewed by: kib
- Merge r232744 changes to pc98.
(Allow a kernel to be built with 'nodevice atpic'.)
- Move ICU related defines from x86/isa/atpic.c to x86/isa/icu.h and
use them in x86/x86/intr_machdep.c.
Reviewed by: jhb
kernel version introduced the sysctl (based upon a linux man-page)
- add comments to sscalls.master regarding some names of sysctls which are
different than the linux-names (based upon the linux unistd.h)
- add some dummy sysctls
- name an unimplemented sysctl
MFC after: 1 month
amd64, if 'device isa' is present quiesce the 8259A's during boot and
resume from suspend.
While here, be more selective on amd64 about which kernel configurations
need elcr.c.
MFC after: 2 weeks
- Return failure for a suspend attempt if we have no wake address.
- Use intr_disable()/intr_restore() instead of ACPI_DISABLE_IRQS().
- Invoke intr_suspend() earlier and call intr_resume() if suspend
fails.
- Use pause in the loop waiting for CPU to suspend.
- Restore PAT MSR, switchtime, switchticks, and MTRRs on resume.
Reviewed by: jkim (earlier version)
MFC after: 2 weeks
platforms.
This will make every attempt to mount a non-mpsafe filesystem to the
kernel forbidden, unless it is expressely compiled with
VFS_ALLOW_NONMPSAFE option.
This patch is part of the effort of killing non-MPSAFE filesystems
from the tree.
No MFC is expected for this patch.
Winbond Super I/O chips.
With minor efforts it should be possible the extend the driver to support
further chips/revisions available from Winbond. In the simplest case
only new IDs need to be added, while different chipsets might require
their own function to enter extended function mode, etc.
Sponsored by: Sandvine Incorporated ULC (in 2011)
Reviewed by: emaste, brueffer
MFC after: 2 weeks
amd64/i386/pc98 ptrace.h with stubs.
For amd64 PT_GETXSTATE and PT_SETXSTATE have been redefined to match the
i386 values. The old values are still supported but should no longer be
used.
Reviewed by: kib
amd64/i386/pc98 endian.h with stubs.
In __bswap64_const(x) the conflict between 0xffUL and 0xffULL has been
resolved by reimplementing the macro in terms of __bswap32(x). As a side
effect __bswap64_var(x) is now implemented using two bswap instructions on
i386 and should be much faster. __bswap32_const(x) has been reimplemented
in terms of __bswap16(x) for consistency.
Vnode-backed mappings cannot be put into the kernel map, since it is a
system map.
Use exec_map for transient mappings, and remove the mappings with
kmem_free_wakeup() to notify the waiters on available map space.
Do not map the whole executable into KVA at all to copy it out into
usermode. Directly use vn_rdwr() for the case of not page aligned
binary.
There is one place left where the potentially unbounded amount of data
is mapped into exec_map, namely, in the COFF image activator
enumeration of the needed shared libraries.
Reviewed by: alc
MFC after: 2 weeks
kernel modules that include binary-only code.
More fine-grained control is provided via MK_SOURCELESS_HOST (for native code
that runs on host CPU) and MK_SOURCELESS_UCODE (for microcode).
Reviewed by: julian, delphij, freebsd-arch
Approved by: kib (mentor)
MFC after: 2 weeks
netback.c: Add missing VM includes.
xen/xenvar.h,
xen/xenpmap.h: Move some XENHVM macros from <machine/xen/xenpmap.h> to
<machine/xen/xenvar.h> on i386 to match the amd64 headers.
conf/files: Add netback to the build.
Submitted by: jhb
MFC after: 3 days
The isci driver is for the integrated SAS controller in the Intel C600
(Patsburg) chipset. Source files in sys/dev/isci directory are
FreeBSD-specific, and sys/dev/isci/scil subdirectory contains
an OS-agnostic library (SCIL) published by Intel to control the SAS
controller. This library is used primarily as-is in this driver, with
some post-processing to better integrate into the kernel build
environment.
isci.4 and a README in the sys/dev/isci directory contain a few
additional details.
This driver is only built for amd64 and i386 targets.
Sponsored by: Intel
Reviewed by: scottl
Approved by: scottl
64bit and 32bit ABIs. As a side-effect, it enables AVX on capable
CPUs.
In particular:
- Query the CPU support for XSAVE, list of the supported extensions
and the required size of FPU save area. The hw.use_xsave tunable is
provided for disabling XSAVE, and hw.xsave_mask may be used to
select the enabled extensions.
- Remove the FPU save area from PCB and dynamically allocate the
(run-time sized) user save area on the top of the kernel stack,
right above the PCB. Reorganize the thread0 PCB initialization to
postpone it after BSP is queried for save area size.
- The dumppcb, stoppcbs and susppcbs now do not carry the FPU state as
well. FPU state is only useful for suspend, where it is saved in
dynamically allocated suspfpusave area.
- Use XSAVE and XRSTOR to save/restore FPU state, if supported and
enabled.
- Define new mcontext_t flag _MC_HASFPXSTATE, indicating that
mcontext_t has a valid pointer to out-of-struct extended FPU
state. Signal handlers are supplied with stack-allocated fpu
state. The sigreturn(2) and setcontext(2) syscall honour the flag,
allowing the signal handlers to inspect and manipilate extended
state in the interrupted context.
- The getcontext(2) never returns extended state, since there is no
place in the fixed-sized mcontext_t to place variable-sized save
area. And, since mcontext_t is embedded into ucontext_t, makes it
impossible to fix in a reasonable way. Instead of extending
getcontext(2) syscall, provide a sysarch(2) facility to query
extended FPU state.
- Add ptrace(2) support for getting and setting extended state; while
there, implement missed PT_I386_{GET,SET}XMMREGS for 32bit binaries.
- Change fpu_kern KPI to not expose struct fpu_kern_ctx layout to
consumers, making it opaque. Internally, struct fpu_kern_ctx now
contains a space for the extended state. Convert in-kernel consumers
of fpu_kern KPI both on i386 and amd64.
First version of the support for AVX was submitted by Tim Bird
<tim.bird am sony com> on behalf of Sony. This version was written
from scratch.
Tested by: pho (previous version), Yamagi Burmeister <lists yamagi org>
MFC after: 1 month
CTL is a disk and processor device emulation subsystem originally written
for Copan Systems under Linux starting in 2003. It has been shipping in
Copan (now SGI) products since 2005.
It was ported to FreeBSD in 2008, and thanks to an agreement between SGI
(who acquired Copan's assets in 2010) and Spectra Logic in 2010, CTL is
available under a BSD-style license. The intent behind the agreement was
that Spectra would work to get CTL into the FreeBSD tree.
Some CTL features:
- Disk and processor device emulation.
- Tagged queueing
- SCSI task attribute support (ordered, head of queue, simple tags)
- SCSI implicit command ordering support. (e.g. if a read follows a mode
select, the read will be blocked until the mode select completes.)
- Full task management support (abort, LUN reset, target reset, etc.)
- Support for multiple ports
- Support for multiple simultaneous initiators
- Support for multiple simultaneous backing stores
- Persistent reservation support
- Mode sense/select support
- Error injection support
- High Availability support (1)
- All I/O handled in-kernel, no userland context switch overhead.
(1) HA Support is just an API stub, and needs much more to be fully
functional.
ctl.c: The core of CTL. Command handlers and processing,
character driver, and HA support are here.
ctl.h: Basic function declarations and data structures.
ctl_backend.c,
ctl_backend.h: The basic CTL backend API.
ctl_backend_block.c,
ctl_backend_block.h: The block and file backend. This allows for using
a disk or a file as the backing store for a LUN.
Multiple threads are started to do I/O to the
backing device, primarily because the VFS API
requires that to get any concurrency.
ctl_backend_ramdisk.c: A "fake" ramdisk backend. It only allocates a
small amount of memory to act as a source and sink
for reads and writes from an initiator. Therefore
it cannot be used for any real data, but it can be
used to test for throughput. It can also be used
to test initiators' support for extremely large LUNs.
ctl_cmd_table.c: This is a table with all 256 possible SCSI opcodes,
and command handler functions defined for supported
opcodes.
ctl_debug.h: Debugging support.
ctl_error.c,
ctl_error.h: CTL-specific wrappers around the CAM sense building
functions.
ctl_frontend.c,
ctl_frontend.h: These files define the basic CTL frontend port API.
ctl_frontend_cam_sim.c: This is a CTL frontend port that is also a CAM SIM.
This frontend allows for using CTL without any
target-capable hardware. So any LUNs you create in
CTL are visible in CAM via this port.
ctl_frontend_internal.c,
ctl_frontend_internal.h:
This is a frontend port written for Copan to do
some system-specific tasks that required sending
commands into CTL from inside the kernel. This
isn't entirely relevant to FreeBSD in general,
but can perhaps be repurposed.
ctl_ha.h: This is a stubbed-out High Availability API. Much
more is needed for full HA support. See the
comments in the header and the description of what
is needed in the README.ctl.txt file for more
details.
ctl_io.h: This defines most of the core CTL I/O structures.
union ctl_io is conceptually very similar to CAM's
union ccb.
ctl_ioctl.h: This defines all ioctls available through the CTL
character device, and the data structures needed
for those ioctls.
ctl_mem_pool.c,
ctl_mem_pool.h: Generic memory pool implementation used by the
internal frontend.
ctl_private.h: Private data structres (e.g. CTL softc) and
function prototypes. This also includes the SCSI
vendor and product names used by CTL.
ctl_scsi_all.c,
ctl_scsi_all.h: CTL wrappers around CAM sense printing functions.
ctl_ser_table.c: Command serialization table. This defines what
happens when one type of command is followed by
another type of command.
ctl_util.c,
ctl_util.h: CTL utility functions, primarily designed to be
used from userland. See ctladm for the primary
consumer of these functions. These include CDB
building functions.
scsi_ctl.c: CAM target peripheral driver and CTL frontend port.
This is the path into CTL for commands from
target-capable hardware/SIMs.
README.ctl.txt: CTL code features, roadmap, to-do list.
usr.sbin/Makefile: Add ctladm.
ctladm/Makefile,
ctladm/ctladm.8,
ctladm/ctladm.c,
ctladm/ctladm.h,
ctladm/util.c: ctladm(8) is the CTL management utility.
It fills a role similar to camcontrol(8).
It allow configuring LUNs, issuing commands,
injecting errors and various other control
functions.
usr.bin/Makefile: Add ctlstat.
ctlstat/Makefile
ctlstat/ctlstat.8,
ctlstat/ctlstat.c: ctlstat(8) fills a role similar to iostat(8).
It reports I/O statistics for CTL.
sys/conf/files: Add CTL files.
sys/conf/NOTES: Add device ctl.
sys/cam/scsi_all.h: To conform to more recent specs, the inquiry CDB
length field is now 2 bytes long.
Add several mode page definitions for CTL.
sys/cam/scsi_all.c: Handle the new 2 byte inquiry length.
sys/dev/ciss/ciss.c,
sys/dev/ata/atapi-cam.c,
sys/cam/scsi/scsi_targ_bh.c,
scsi_target/scsi_cmds.c,
mlxcontrol/interface.c: Update for 2 byte inquiry length field.
scsi_da.h: Add versions of the format and rigid disk pages
that are in a more reasonable format for CTL.
amd64/conf/GENERIC,
i386/conf/GENERIC,
ia64/conf/GENERIC,
sparc64/conf/GENERIC: Add device ctl.
i386/conf/PAE: The CTL frontend SIM at least does not compile
cleanly on PAE.
Sponsored by: Copan Systems, SGI and Spectra Logic
MFC after: 1 month
It seems strchr() and strrchr() are used more often than index() and
rindex(). Therefore, simply migrate all kernel code to use it.
For the XFS code, remove an empty line to make the code identical to
the code in the Linux kernel.
are booting inside a VM. There are three reasons to disable this:
o It causes the VM host to believe that all the tested pages or RAM are
in use. This in turn may force the host to page out pages of RAM
belonging to other VMs, or otherwise cause problems with fair resource
sharing on the VM cluster.
o It adds significant time to the boot process (around 1 second/Gig in
testing)
o It is unnecessary - the host should have already verified that the
memory is functional etc.
Note that this simply changes the default when in a VM - it can still be
overridden using the hw.memtest.tests tunable.
MFC after: 4 weeks
When r207410 eliminated the acquisition and release of the page queues
lock from pmap_extract_and_hold(), it didn't take into account that
pmap_pte_quick() sometimes requires the page queues lock to be held.
This change reimplements pmap_extract_and_hold() such that it no
longer uses pmap_pte_quick(), and thus never requires the page queues
lock.
Merge r177525 from the native pmap
Prevent the overflow in the calculation of the next page directory.
The overflow causes the wraparound with consequent corruption of the
(almost) whole address space mapping.
Strictly speaking, r177525 is not required by the Xen pmap because the
hypervisor steals the uppermost region of the normal kernel address
space. I am nonetheless merging it in order to reduce the number of
unnecessary differences between the native and Xen pmap implementations.
Tested by: sbruno
configurations for various architectures in FreeBSD 10.x. This allows
basic Capsicum functionality to be used in the default FreeBSD
configuration on non-embedded architectures; process descriptors are not
yet enabled by default.
MFC after: 3 months
Sponsored by: Google, Inc
paravirtualized pmap implementations for i386. This includes some
style fixes to the native pmap and several bug fixes that were not
previously applied to the paravirtualized pmap.
Tested by: sbruno
MFC after: 3 weeks
initializing structures, like the pv table, that are only used to
implement superpages. In fact, some of the unnecessary code in
pmap_init() was actually doing harm. It was preventing the kernel from
booting on virtual machines with more than 768 MB of memory.
Tested by: sbruno
Since mpboot.s enables processor support for PG_PS before enabling
paging, there is no reason that the identity must use 4 KB page mappings.
Discussed with: jhb
VM_KMEM_SIZE_MAX. Specifically, if the user/kernel address space split
was changed such that the kernel address space was greater than or equal
to 2 GB, then overflow would occur.
PR: 161721
MFC after: 3 weeks
one. Interestingly, these are actually the default for quite some time
(bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
since r52045) but even recently added device drivers do this unnecessarily.
Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
Discussed with: jhb
- Also while at it, use __FBSDID.
system calls to provide feed-forward clock management capabilities to
userspace processes. ffclock_getcounter() returns the current value of the
kernel's feed-forward clock counter. ffclock_getestimate() returns the current
feed-forward clock parameter estimates and ffclock_setestimate() updates the
feed-forward clock parameter estimates.
- Document the syscalls in the ffclock.2 man page.
- Regenerate the script-derived syscall related files.
Committed on behalf of Julien Ridoux and Darryl Veitch from the University of
Melbourne, Australia, as part of the FreeBSD Foundation funded "Feed-Forward
Clock Synchronization Algorithms" project.
For more information, see http://www.synclab.org/radclock/
Submitted by: Julien Ridoux (jridoux at unimelb edu au)
The current code mixes the use of `flags' and `mode'. This is a bit
confusing, since the faccessat() function as a `flag' parameter to store
the AT_ flag.
Make this less confusing by using the same name as used in the POSIX
specification -- `amode'.
all the architectures.
The option allows to mount non-MPSAFE filesystem. Without it, the
kernel will refuse to mount a non-MPSAFE filesytem.
This patch is part of the effort of killing non-MPSAFE filesystems
from the tree.
No MFC is expected for this patch.
Tested by: gianni
Reviewed by: kib
The SYSCTL_NODE macro defines a list that stores all child-elements of
that node. If there's no SYSCTL_DECL macro anywhere else, there's no
reason why it shouldn't be static.
31, but that vector is reserved.
Without this fix, running dtrace -p <pid> would either cause the target
process to crash or the kernel to page fault.
Obtained from: rpaulo
MFC after: 3days
replace amd(4) with the former in the amd64, i386 and pc98 GENERIC kernel
configuration files. Besides duplicating functionality, amd(4), which
previously also supported the AMD Am53C974, unlike esp(4) is no longer
maintained and has accumulated enough bit rot over time to always cause
a panic during boot as long as at least one target is attached to it
(see PR 124667).
PR: 124667
Obtained from: NetBSD (based on)
MFC after: 3 days
thing when changing the debugging options as part of head becoming a new
stable branch. It may also help people who for one reason or another want
to run head but don't want it slowed down by the debugging support.
Reviewed by: kib
implement a deprecated FPU control interface in addition to the
standard one. To make this clearer, further deprecate ieeefp.h
by not declaring the function prototypes except on architectures
that implement them already.
Currently i386 and amd64 implement the ieeefp.h interface for
compatibility, and for fp[gs]etprec(), which doesn't exist on
most other hardware. Powerpc, sparc64, and ia64 partially implement
it and probably shouldn't, and other architectures don't implement it
at all.
As part of the 8.0-RELEASE cycle this was done in stable/8 (r199112)
but was left alone in head so people could work on fixing an issue that
caused boot failure on some motherboards. Apparently nobody has worked
on it and we are getting reports of boot failure with the 9.0 test builds.
So this time I'll comment out the driver in head (still hoping someone
will work on it) and MFC to stable/9.
Submitted by: Alberto Villa <avilla at FreeBSD dot org>
thanks for their contiued support to FreeBSD.
This is version 10.80.00.003 from codeset 10.2.1 [1]
Obtained from: LSI http://kb.lsi.com/Download16574.aspx [1]
- Replace instances of manual assembly instruction "hlt" call
with halt() function calling.
- In cpu_idle_mwait() avoid races in check to sched_runnable() using
the same pattern used in cpu_idle_hlt() with the 'hlt' instruction.
- Add comments explaining the logic behind the pattern used in
cpu_idle_hlt() and other idle callbacks.
In collabouration with: jhb, mav
Reviewed by: adri, kib
MFC after: 3 weeks
patch modifies makesyscalls.sh to prefix all of the non-compatibility
calls (e.g. not linux_, freebsd32_) with sys_ and updates the kernel
entry points and all places in the code that use them. It also
fixes an additional name space collision between the kernel function
psignal and the libc function of the same name by renaming the kernel
psignal kern_psignal(). By introducing this change now we will ease future
MFCs that change syscalls.
Reviewed by: rwatson
Approved by: re (bz)
flags field. Updates to the atomic flags are performed using the atomic
ops on the containing word, do not require any vm lock to be held, and
are non-blocking. The vm_page_aflag_set(9) and vm_page_aflag_clear(9)
functions are provided to modify afalgs.
Document the changes to flags field to only require the page lock.
Introduce vm_page_reference(9) function to provide a stable KPI and
KBI for filesystems like tmpfs and zfs which need to mark a page as
referenced.
Reviewed by: alc, attilio
Tested by: marius, flo (sparc64); andreast (powerpc, powerpc64)
Approved by: re (bz)
devices supported by puc(4) to work "out of the box" since puc.ko does
not work "out of the box".
Reviewed by: marcel
Approved by: re (kib)
MFC after: 1 week
temporary variable and check with if as TUNABLE_*_FETCH do not
alter values unless successfully found the tunable.
Reported by: jhb, bde
MFC after: 3 days
X-MFC with: r224516
Approved by: re (kib)
kernel for FreeBSD 9.0:
Add a new capability mask argument to fget(9) and friends, allowing system
call code to declare what capabilities are required when an integer file
descriptor is converted into an in-kernel struct file *. With options
CAPABILITIES compiled into the kernel, this enforces capability
protection; without, this change is effectively a no-op.
Some cases require special handling, such as mmap(2), which must preserve
information about the maximum rights at the time of mapping in the memory
map so that they can later be enforced in mprotect(2) -- this is done by
narrowing the rights in the existing max_protection field used for similar
purposes with file permissions.
In namei(9), we assert that the code is not reached from within capability
mode, as we're not yet ready to enforce namespace capabilities there.
This will follow in a later commit.
Update two capability names: CAP_EVENT and CAP_KEVENT become
CAP_POST_KEVENT and CAP_POLL_KEVENT to more accurately indicate what they
represent.
Approved by: re (bz)
Submitted by: jonathan
Sponsored by: Google Inc
to VPO_UNMANAGED (and also making the flag protected by the vm object
lock, instead of vm page queue lock).
- Mark the fake pages with both PG_FICTITIOUS (as it is now) and
VPO_UNMANAGED. As a consequence, pmap code now can use use just
VPO_UNMANAGED to decide whether the page is unmanaged.
Reviewed by: alc
Tested by: pho (x86, previous version), marius (sparc64),
marcel (arm, ia64, powerpc), ray (mips)
Sponsored by: The FreeBSD Foundation
Approved by: re (bz)
NFSCL, NFSD instead of NFSCLIENT, NFSSERVER since
NFSCL and NFSD are now the defaults. The client change is
needed for diskless configurations, so that the root
mount works for fstype nfs.
Reported by seanbru at yahoo-inc.com for i386/XEN.
Approved by: re (hrs)
In particular:
- fix format specifiers in the DPRINTFs;
- do not use kernel_map for temporal mapping backed by the vnode, this
cannot work since kernel map is a system map. Use exec_map instead.
- ignore error code from an attempt to insert the hole. If supposed hole
is located at the region already populated by .bss, it is not an error.
- correctly translate vm error codes to errno, when appropriate.
Reported and tested by: Rich Naill <rich enterprisesystems net>
Approved by: re (kensmith)
MFC after: 1 week
memtesting, which can easily save seconds to minutes of boot time.
The tunable name is kept general to allow reusing the code in
alternate frameworks.
Requested by: many
Discussed on: arch (a while a go)
Obtained from: Sandvine Incorporated
Reviewed by: sbruno
Approved by: re (kib)
MFC after: 2 weeks
This patch is going to help in cases like mips flavours where you
want a more granular support on MAXCPU.
No MFC is previewed for this patch.
Tested by: pluknet
Approved by: re (kib)
sintrcnt/sintrnames which are symbols containing the size of the 2
tables.
- For amd64/i386 remove the storage of intr* stuff from assembly files.
This area can be widely improved by applying the same to other
architectures and likely finding an unified approach among them and
move the whole code to be MI. More work in this area is expected to
happen fairly soon.
No MFC is previewed for this patch.
Tested by: pluknet
Reviewed by: jhb
Approved by: re (kib)
Back in 2009 I changed the ABI of the GIO_KEYMAP and PIO_KEYMAP ioctls
to support wide characters. I created a patch to add ABI compatibility
for the old calls, but I didn't get any feedback to that.
It seems now people are upgrading from 8 to 9 they experience this
issue, so add it anyway.
%rcx as "extensions" in long mode. If any unused bit is set in %rcx, these
instructions cause general protection fault. Fix style nits and synchronize
i386 with amd64.
more explicit comments about what's going on and what future maintainers
need to do when e.g. adding a new operation to a sys_machdep.c.
Approved by: mentor(rwatson), re(bz)
option to vm_object_page_remove() asserts that the specified range of pages
is not mapped, or more precisely that none of these pages have any managed
mappings. Thus, vm_object_page_remove() need not call pmap_remove_all() on
the pages.
This change not only saves time by eliminating pointless calls to
pmap_remove_all(), but it also eliminates an inconsistency in the use of
pmap_remove_all() versus related functions, like pmap_remove_write(). It
eliminates harmless but pointless calls to pmap_remove_all() that were being
performed on PG_UNMANAGED pages.
Update all of the existing assertions on pmap_remove_all() to reflect this
change.
Reviewed by: kib
to do with global namespaces) and CAPABILITIES (which has to do with
constraining file descriptors). Just in case, and because it's a better
name anyway, let's move CAPABILITIES out of the way.
Also, change opt_capabilities.h to opt_capsicum.h; for now, this will
only hold CAPABILITY_MODE, but it will probably also hold the new
CAPABILITIES (implying constrained file descriptors) in the future.
Approved by: rwatson
Sponsored by: Google UK Ltd
resource allocation from an x86 Host-PCI bridge driver so that it can be
reused by the ACPI Host-PCI bridge driver (and eventually the MPTable
Host-PCI bridge driver) instead of duplicating the same logic. Note that
this means that hw.acpi.host_mem_start is now replaced with the
hw.pci.host_mem_start tunable that was already used in the non-ACPI case.
This also removes hw.acpi.host_mem_start on ia64 where it was not
applicable (the implementation was very x86-specific).
While here, adjust the logic to apply the new start address on any
"wildcard" allocation even if that allocation comes from a subset of
the allowable address range.
Reviewed by: imp (1)
The generic sound driver has been added, along with enough
device-specific drivers to support the most common audio
chipsets.
We've discussed enabling it from time to time over the years
and we've received numerous requests from users, so we decided
that shipping 9.0 with working audio by default would be the
best thing to do.
Bug reports should be sent to the multimedia@ mailing list, as
usual.
Approved by: mav
No objection: re
The code has definitely been broken for SCHED_ULE, which is a default
scheduler. It may have been broken for SCHED_4BSD in more subtle ways,
e.g. with manually configured CPU affinities and for interrupt devilery
purposes.
We still provide a way to disable individual CPUs or all hyperthreading
"twin" CPUs before SMP startup. See the UPDATING entry for details.
Interaction between building CPU topology and disabling CPUs still
remains fuzzy: topology is first built using all availble CPUs and then
the disabled CPUs should be "subtracted" from it. That doesn't work
well if the resulting topology becomes non-uniform.
This work is done in cooperation with Attilio Rao who in addition to
reviewing also provided parts of code.
PR: kern/145385
Discussed with: gcooper, ambrisko, mdf, sbruno
Reviewed by: attilio
Tested by: pho, pluknet
X-MFC after: never
This regression was introduced in r213323.
There are probably no Intel cpus that support amd64 mode, but do not
support cpuid level 4, but it's better to keep i386 and amd64 versions
of this code in sync.
Discovered by: pho
Tested by: pho
MFC after: 2 weeks
be brought up in the order they are enumerated in the device tree (in
particular, that thread 0 on each core be brought up first). The SLIST
through which we loop to start the CPUs has all of its entries added with
SLIST_INSERT_HEAD(), which means it is in reverse order of enumeration
and so AP startup would always fail in such situations (causing a machine
check or RTAS failure). Fix this by changing the SLIST into an STAILQ,
and inserting new CPUs at the end.
Reviewed by: jhb
Note AMD dropped SSE5 extensions in order to avoid ISA overlap with Intel
AVX instructions. The SSE5 bit was recycled as XOP extended instruction
bit, CVT16 was deprecated in favor of F16C (half-precision float conversion
instructions for AVX), and the remaining FMA4 (4-operand FMA instructions)
gained a separate CPUID bit. Replace non-existent references with today's
CPUID specifications.
architectures (i386, for example) the virtual memory space may be
constrained enough that 2MB is a large chunk. Use 64K for arches
other than amd64 and ia64, with special handling for sparc64 due to
differing hardware.
Also commit the comment changes to kmem_init_zero_region() that I
missed due to not saving the file. (Darn the unfamiliar development
environment).
Arch maintainers, please feel free to adjust ZERO_REGION_SIZE as you
see fit.
Requested by: alc
MFC after: 1 week
MFC with: r221853
Xen timer and time counter to provide one-shot and periodic time events.
On my tests this reduces idle interruts rate down to about 30Hz, and accor-
ding to Xen VM Manager reduces host CPU load by three times comparing to
the previous periodic 100Hz clock. Also now, when needed, it is possible to
increase HZ rate without useless CPU burning during idle periods.
Now only ia64 and some ARMs left not migrated to the new event timers.
when the user has indicated that the system has synchronized TSCs or it has
P-state invariant TSCs. For the former case, we may clear the tunable if it
fails the test to prevent accidental foot-shooting. For the latter case, we
may set it if it passes the test to notify the user that it may be usable.
This also introduces a new detection path for family 10h and newer
pre-bulldozer cpus, pre-10h hardware should not be affected.
Tested by: Gary Jennejohn <gljennjohn@googlemail.com>
(with pre-10h hardware)
MFC after: 2 weeks
cpuset_t objects.
That is going to offer the underlying support for a simple bump of
MAXCPU and then support for number of cpus > 32 (as it is today).
Right now, cpumask_t is an int, 32 bits on all our supported architecture.
cpumask_t on the other side is implemented as an array of longs, and
easilly extendible by definition.
The architectures touched by this commit are the following:
- amd64
- i386
- pc98
- arm
- ia64
- XEN
while the others are still missing.
Userland is believed to be fully converted with the changes contained
here.
Some technical notes:
- This commit may be considered an ABI nop for all the architectures
different from amd64 and ia64 (and sparc64 in the future)
- per-cpu members, which are now converted to cpuset_t, needs to be
accessed avoiding migration, because the size of cpuset_t should be
considered unknown
- size of cpuset_t objects is different from kernel and userland (this is
primirally done in order to leave some more space in userland to cope
with KBI extensions). If you need to access kernel cpuset_t from the
userland please refer to example in this patch on how to do that
correctly (kgdb may be a good source, for example).
- Support for other architectures is going to be added soon
- Only MAXCPU for amd64 is bumped now
The patch has been tested by sbruno and Nicholas Esborn on opteron
4 x 12 pack CPUs. More testing on big SMP is expected to came soon.
pluknet tested the patch with his 8-ways on both amd64 and i386.
Tested by: pluknet, sbruno, gianni, Nicholas Esborn
Reviewed by: jeff, jhb, sbruno
driver would verify that requests for child devices were confined to any
existing I/O windows, but the driver relied on the firmware to initialize
the windows and would never grow the windows for new requests. Now the
driver actively manages the I/O windows.
This is implemented by allocating a bus resource for each I/O window from
the parent PCI bus and suballocating that resource to child devices. The
suballocations are managed by creating an rman for each I/O window. The
suballocated resources are mapped by passing the bus_activate_resource()
call up to the parent PCI bus. Windows are grown when needed by using
bus_adjust_resource() to adjust the resource allocated from the parent PCI
bus. If the adjust request succeeds, the window is adjusted and the
suballocation request for the child device is retried.
When growing a window, the rman_first_free_region() and
rman_last_free_region() routines are used to determine if the front or
end of the existing I/O window is free. From using that, the smallest
ranges that need to be added to either the front or back of the window
are computed. The driver will first try to grow the window in whichever
direction requires the smallest growth first followed by the other
direction if that fails.
Subtractive bridges will first attempt to satisfy requests for child
resources from I/O windows (including attempts to grow the windows). If
that fails, the request is passed up to the parent PCI bus directly
however.
The PCI-PCI bridge driver will try to use firmware-assigned ranges for
child BARs first and only allocate a "fresh" range if that specific range
cannot be accommodated in the I/O window. This allows systems where the
firmware assigns resources during boot but later wipes the I/O windows
(some ACPI BIOSen are known to do this) to "rediscover" the original I/O
window ranges.
The ACPI Host-PCI bridge driver has been adjusted to correctly honor
hw.acpi.host_mem_start and the I/O port equivalent when a PCI-PCI bridge
makes a wildcard request for an I/O window range.
The new PCI-PCI bridge driver is only enabled if the NEW_PCIB kernel option
is enabled. This is a transition aide to allow platforms that do not
yet support bus_activate_resource() and bus_adjust_resource() in their
Host-PCI bridge drivers (and possibly other drivers as needed) to use the
old driver for now. Once all platforms support the new driver, the
kernel option and old driver will be removed.
PR: kern/143874 kern/149306
Tested by: mav
function on the possibility of a thread to not preempt.
As this function is very tied to x86 (interrupts disabled checkings)
it is not intended to be used in MI code.
disk dumping.
With the option SW_WATCHDOG on, these operations are doomed to let
watchdog fire, fi they take too long.
I implemented the stubs this way because I really want wdog_kern_*
KPI to not be dependant by SW_WATCHDOG being on (and really, the option
only enables watchdog activation in hardclock) and also avoid to
call them when not necessary (avoiding not-volountary watchdog
activations).
Sponsored by: Sandvine Incorporated
Discussed with: emaste, des
MFC after: 2 weeks
NFS client (which I guess is no longer experimental). The fstype "newnfs"
is now "nfs" and the regular/old NFS client is now fstype "oldnfs".
Although mounts via fstype "nfs" will usually work without userland
changes, an updated mount_nfs(8) binary is needed for kernels built with
"options NFSCL" but not "options NFSCLIENT". Updated mount_nfs(8) and
mount(8) binaries are needed to do mounts for fstype "oldnfs".
The GENERIC kernel configs have been changed to use options
NFSCL and NFSD (the new client and server) instead of NFSCLIENT and NFSSERVER.
For kernels being used on diskless NFS root systems, "options NFSCL"
must be in the kernel config.
Discussed on freebsd-fs@.
device in /dev/ create symbolic link with adY name, trying to mimic old ATA
numbering. Imitation is not complete, but should be enough in most cases to
mount file systems without touching /etc/fstab.
- To know what behavior to mimic, restore ATA_STATIC_ID option in cases
where it was present before.
- Add some more details to UPDATING.
set the f_flags field of "struct statfs". This had the interesting
effect of making the NFSv4 mounts "disappear" after r221014,
since NFSMNT_NFSV4 and MNT_IGNORE became the same bit.
Move the files used for a diskless NFS root from sys/nfsclient
to sys/nfs in preparation for them to be used by both NFS
clients. Also, move the declaration of the three global data
structures from sys/nfsclient/nfs_vfsops.c to sys/nfs/nfs_diskless.c
so that they are defined when either client uses them.
Reviewed by: jhb
MFC after: 2 weeks
stack. It means that all legacy ATA drivers are disabled and replaced by
respective CAM drivers. If you are using ATA device names in /etc/fstab or
other places, make sure to update them respectively (adX -> adaY,
acdX -> cdY, afdX -> daY, astX -> saY, where 'Y's are the sequential
numbers for each type in order of detection, unless configured otherwise
with tunables, see cam(4)).
ataraid(4) functionality is now supported by the RAID GEOM class.
To use it you can load geom_raid kernel module and use graid(8) tool
for management. Instead of /dev/arX device names, use /dev/raid/rX.
Add pmap_invalidate_cache_pages() method on x86. It flushes the CPU
cache for the set of pages, which are not neccessary mapped. Since its
supposed use is to prepare the move of the pages ownership to a device
that does not snoop all CPU accesses to the main memory (read GPU in
GMCH), do not rely on CPU self-snoop feature.
amd64 implementation takes advantage of the direct map. On i386,
extract the helper pmap_flush_page() from pmap_page_set_memattr(), and
use it to make a temporary mapping of the flushed page.
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 3 weeks
32 bits. Some times compiler inserts unnecessary instructions to preserve
unused upper 32 bits even when it is casted to a 32-bit value. It reduces
such compiler mistakes where every cycle counts.
MPERF MSRs are available. It was disabled in r216443. Remove the earlier
hack to subtract 0.5% from the calibrated frequency as DELAY(9) is little
bit more reliable now.
safer for i386 because it can be easily over 4 GHz now. More worse, it can
be easily changed by user with 'machdep.tsc_freq' tunable (directly) or
cpufreq(4) (indirectly). Note it is intentionally not used in performance
critical paths to avoid performance regression (but we should, in theory).
Alternatively, we may add "virtual TSC" with lower frequency if maximum
frequency overflows 32 bits (and ignore possible incoherency as we do now).
functions are implemented with CMPXCHG8B instruction where it is available,
i. e., all Pentium-class and later processors. Note this instruction is
also used for atomic_store_rel_64() because a simple XCHG-like instruction
for 64-bit memory access does not exist, unfortunately. If the processor
lacks the instruction, i. e., 80486-class CPUs, two 32-bit load/store are
performed with interrupt temporarily disabled, assuming it does not support
SMP. Although this assumption may be little naive, it is true in reality.
This implementation is inspired by Linux.
at run-time on i386. cpu_ticks() is set to use RDTSC early enough on i386
where it is available. Otherwise, cpu_ticks() is driven by the current
timecounter hardware as binuptime(9) does. This also avoids unnecessary
namespace pollution from <machine/cputypes.h>.
I have not properly thought through the commit. After r220031 (linux
compat: improve and fix sendmsg/recvmsg compatibility) the basic
handling for SO_PASSCRED is not sufficient as it breaks recvmsg
functionality for SCM_CREDS messages because now we would need to handle
sockcred data in addition to cmsgcred. And that is not implemented yet.
Pointyhat to: avg
Introduce the AHB glue for Atheros embedded systems. Right now it's
hard-coded for the AR9130 chip whose support isn't yet in this HAL;
it'll be added in a subsequent commit.
Kernel configuration files now need both 'ath' and 'ath_pci' devices; both
modules need to be loaded for the ath device to work.
This seems to have been a part of a bigger patch by dchagin that either
haven't been committed or committed partially.
Submitted by: dchagin, nox
MFC after: 2 weeks
And drop dummy definitions for those system calls.
This may transiently break the build.
PR: kern/149168
Submitted by: John Wehle <john@feith.com>
Reviewed by: netchild
MFC after: 2 weeks
Since signal trampolines are copied to the shared page do not need to
leave place on the stack for it. Forgotten in the previous commit.
MFC after: 1 Week
