be usable as the default timer in place of the physical timer.
We are guaranteed to have access to the virtual timer, but when running
under a hypervisor may not have access to the physical.
Differential Revision: https://reviews.freebsd.org/D588
few "general purpose registers" whose values control chip behavior in ways
that have nothing to do with IO pin mux control. Define a simple API that
other soc-specific code can use to read and write the registers, and provide
the imx51 implementation of them.
- miibus fixes as suggested by Yonghyeon Pyun.
- enable VLAN MTU support.
- fix a few WITNESS complaints in cgem_attach().
- have cgem_attach() properly init the ifnet struct before calling
mii_attach() to fix panic when using e1000phy.
- fix ethernet address changing.
- fix transmit queue overflow handling.
- tweak receive queue handling to reduce receive overflows.
- bring out MAC statistic counters to sysctls.
- add e1000phy to config file.
- implement receive hang work-around described in reference guide.
- change device name from if_cgem to cgem to be consistent with other
interfaces.
Submitted by: Thomas Skibo <ThomasSkibo@sbcglobal.net>
Reviewed by: wkoszek, Yonghyeon PYUN <pyunyh@gmail.com>
. interrupt storm detected on "intr70:"; throttling interrupt source;
. Added access serialization on iicbus_transfer(), previously there was
no such protection and a new transfer could easily confuse the
controller;
. Add error checkings (i.e. stop the transfer when a error is detected
and do _not_ overwrite the previous error);
. On command done interrupt do not assume that the transfer was finished
sucessfully as we will receive the command done interrupt even after
errors;
. Simplify the FIFO handling;
. Reset the FIFO between the transfers as the FIFO may contain data from
the last (failed) transfer;
. Fix the iicbus speed for AM335x, which in turn will make better use of
the I2C noise filter (set to one internal clock cycle);
. Move the read and write handler to ithread instead of notifying the
requesting thread with wakeup(9);
. Fix the comments based on OMAP4 TRM.
The above changes allows me to read the EDID from my HDMI monitor on BBB
with gonzo's patches to support TDA19988 (which does 128 bytes reads) and
repeatedly scan the iicbus (with a modified i2c(8)) without lock up the bus.
Phabric: D465
header (Elf_Ehdr) to determine if a particular interpretor wants to
accept it or not. Use this mechanism to filter EABI arm on OABI arm
kernels, and vice versa. This method could also be used to implement
OABI on EABI arm kernels, if desired, or to allow a single mips kernel
to run o32, n32 and n64 binaries.
Differential Revision: https://reviews.freebsd.org/D609
soc-wide info lives. It was under dev.imx6_anatop.0.
What does anatop mean anyway? Nobody seems to know, so it's probably
not where somebody will think to look for imx6 hardware info.
configure the mux and config registers for PIO devices based on what
we find in the FDT. I developed it per the spec that had been
committed to Linux in the January 2014 time frame and haven't
updated. In short, bundles of pins are activated in specific ways for
specific configurations, and we implement all of that.
What's not included is a MI device infrastructure, any dynamic
run-time changing of these pins, etc. Also not included are hooks into
all the drivers to enable the latter (static at boot no driver changes
are needed). These larger questions will need to be answered once we
have more drivers like this for more platforms, or somebody has a heck
of a lot of time to research a bunch of platforms, the Linux solution
(which is good, but has its warts), etc.
work. This gets my AT91SAM9260-based boards almost booting with
current in multi pass. The MCI driver is broken, but it is equally
broken before multi-pass.
By Richard Earnshaw at ARM
>
>GCC has for a number of years provides a set of pre-defined macros for
>use with determining the ISA and features of the target during
>pre-processing. However, the design was always somewhat cumbersome in
>that each new architecture revision created a new define and then
>removed the previous one. This meant that it was necessary to keep
>updating the support code simply to recognise a new architecture being
>added.
>
>The ACLE specification (ARM C Language Extentions)
>(http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.set.swdev/index.html)
>provides a much more suitable interface and GCC has supported this
>since gcc-4.8.
>
>This patch makes use of the ACLE pre-defines to map to the internal
>feature definitions. To support older versions of GCC a compatibility
>header is provided that maps the traditional pre-defines onto the new
>ACLE ones.
Stop using __FreeBSD_ARCH_armv6__ and switch to __ARM_ARCH >= 6 in the
couple of places in tree. clang already implements ACLE. Add a define
that says we implement version 1.1, even though the implementation
isn't quite complete.
mapping size (currently unused). The flags includes the fault access
bits, wired flag as PMAP_ENTER_WIRED, and a new flag
PMAP_ENTER_NOSLEEP to indicate that pmap should not sleep.
For powerpc aim both 32 and 64 bit, fix implementation to ensure that
the requested mapping is created when PMAP_ENTER_NOSLEEP is not
specified, in particular, wait for the available memory required to
proceed.
In collaboration with: alc
Tested by: nwhitehorn (ppc aim32 and booke)
Sponsored by: The FreeBSD Foundation and EMC / Isilon Storage Division
MFC after: 2 weeks
