Return BUS_PROBE_LOW_PRIORITY for a successful probe. This is in
preparation of the introduction of scc(4), which is going to handle
SCCs in the near future.
mutex.
- Don't use callout_drain() to stop the toffhandle callout while holding the
fdc mutex (this could deadlock) in functions called from softclock
(callouts aren't allowed to do voluntary sleeps). Instead, use
callout_stop(). Note that since we hold the associated mutex and are now
using callout_init_mtx(), callout_stop() is just as effective as
callout_drain(). (Though callout_drain() is still needed in detach to
make sure softclock isn't contesting on our mutex before we destroy the
mutex.)
- Remove unused callout 'tohandle' from softc.
MFC after: 1 week
interrupt handlers rather than BUS_SETUP_INTR() and BUS_TEARDOWN_INTR().
Uses of the BUS_*() versions in the implementation of foo_intr methods
in bus drivers were not changed. Mostly this just means that some
drivers might start printing diagnostic messages like [FAST] when
appropriate as well as honoring mpsafenet=0.
- Fix two more of the ppbus drivers' identify routines to function
correctly in the mythical case of a machine with more than one ppbus.
processing the interrupt events. If we clear them afterwards we
can completely miss some events as the NIC can change the source
flags while we're in the handler. In order to not get another
interrupt while we're in ifp->if_input() with the driver lock
dropped we now turn off NIC interrupts while in the interrupt
handler. Previously this was meant to be achieved by clearing the
interrupt source flags after processing the interrupt events but
didn't really work as clearing these flags doesn't actually
acknowledge and re-enable the events.
This fixes the device timeouts seen with the VMware LANCE.
- Relax the watchdog timer somewhat; don't enable it until the last
packet is enqueued and if there is a TX interrupt but there are
still outstanding ones reload the timer.
Reported and tested by: Morten Rodal <morten@rodal.no>
MFC after: 3 days
The ed driver on pc98 was broken by if_edvar.h rev1.31.
Reported by: Kaho Toshikazu (kaho at elam kais kyoto-u ac jp)
Tested by: Eiji Kato (ekato at a1 mbn or jp)
MFC after: 3 days
More info regarding these nics can be found at http://www.myri.com.
Please note that the files
sys/dev/myri10ge/{mcp_gen_header.h,myri10ge_mcp.h} are internally
shared between all our drivers (solaris, macosx, windows, linux, etc).
I'd like to keep these files unchanged, so I can just import newer
versions of them when the firmware API/ABI changes. This means I'm
stuck with some of the crazy-long #define names, and possibly
non-style(9) characteristics of these files.
Many thanks to mlaier for doing firmware(9) just as I
needed it, and to scottl for his helpful review.
Reviewed by: scottl, glebius
Sponsored by: Myricom Inc.
forcing DMA alignment to default buffer size.
- Make sure DMA pointer properly aligned to avoid being truncated by caller
which causing severe underruns and random popping (especially in 32bit
playback / recording).
- Add AC97 inverted external amplifier quirk for Maxselect x710s
- http://maxselect.ru/
MFC after: 1 week
the SMI/TCO address space. Switch the bus space I/O to the
one specific for either the SMI or TCO space. Re-calibrate
the tick. Add some more device id's, 82801FBR submitted by des.
This makes it work on the platforms I've tested with.
Go ahead by: des
should fix strange link state behaviour reported for bcm5721 & bcm5704c
2) Clear bge_link flag in bge_stop()
3) Force link state check after bge_ifmedia_upd(). Otherwise we can miss link
event if PHY changes it's state fast enough.
Tested by: phk (bcm5704c)
Approved by: glebius (mentor)
MFC after: 1 week
Acknowledgement should definitly go to JMicron Technology for providing full
docs on the metadata format as the only vendor so far, big thanks from here.
- In em_attach() remove em_check_for_link(). Not needed here, since
already done in em_hardware_init().
- In em_attach() replace the printing block with call to
em_update_link_status().
- Remove modification of sc->link_state from em_hardware_init() and
from em_media_status(). This makes em_update_link_status() a
single point of change. Call em_update_link_status() where needed.
to getting rid u_int for uint and so on).
b) Turn back on 64 bit DAC support. Cheeze it a bit in that we have two
DMA callback functions- one when we have bus_addr_t > 4 bits in width and
the other which should be normal. Even Cheezier in that we turn off setting
up DMA maps to be BUS_SPACE_MAXADDR if we're in ISP_TARGET_MODE. More work
on this in a week or so.
c) Tested under amd64 and 1MB DFLTPHYS, sparc64, i386 (PAE, but insufficient
memory to really test > 4GB). LINT check under amd64.
MFC after: 1 month
automatically both SATA and SAS drives. The async SAS event handling we catch
but ignore at present (so automagic attach/detach isn't hooked up yet).
Do 64 bit PCI support- we can now work on systems with > 4GB of memory.
Do large transfer support- we now can support up to reported chain depth, or
the length of our request area. We simply allocate additional request elements
when we would run out of room for chain lists.
Tested on Ultra320, FC and SAS controllers on AMD64 and i386 platforms.
There were no RAID cards available for me to regression test.
The error recovery for this driver still is pretty bad.
to work with ipmitools. It works with other tools that have an OpenIPMI
driver interface. The port will need to get updated to used this.
I have not implemented the IPMB mode yet so ioctl's for that don't
really do much otherwise it should work like the OpenIPMI version.
The ipmi.h definitions was derived from the ipmitool header file.
The bus attachments are done for smbios and pci/smbios. Differences
in bus probe order for modules/static are delt with. ACPI attachment
should be done.
This drivers registers with the watchdod(4) interface
Work to do:
- BT interface
- IPMB mode
This has been tested on Dell PE2850, PE2650 & PE850 with i386 & amd64
kernel.
I will link this into the build on next week.
Tom Rhodes, helped me with the man page.
Sponsored by: IronPort Systems Inc.
Inspired from: ipmitool & Linux
o add dfs+radar hooks; DFS is presently disabled in the hal
o channel and mode handling changes
o various api changes
o be more aggressive about iq calibration settling so ap mode
operation is better immediately after startup
o rfkill/rfsilent sysctl support
o tpc ack/cts sysctl support
MFC after: 2 weeks
o assume all data frames have been classified so there's no need
to check if QoS is being used, just fetch the wme priority from
the mbuf
o fix double counting of noack frames
o fix nearby comment
MFC after: 2 weeks
o pull nexttbtt forward in adhoc mode too
o resync beacon timers on joining a bss or ibss as the tstamp we
collected while scanning is almost certainly out of date
Note we may need to refine the ibss mode check in ath_recv_mgmt.
Reviewed by: avatar, dyoung
Obtained from: atheros
MFC after: 2 weeks
frame and if we get a beacon miss interrupt ignore it if we've received
a frame within the beacon miss interval. This should never trigger
and the handling at the net80211 layer should likewise deal with this
but it doesn't hurt and can suppress extranous probe request frames.
Note that we can legtimately get a bmiss when under heavy load.
MFC after: 2 weeks
- Restart watchdog if we *did* processed any descriptors. [1]
- Log the watchdog event if the link is *up*. [2]
PR: kern/92948 [1]
Submitted by: Mihail Balikov <mihail.balikov interbgc.com> [1]
PR: kern/92895 [2]
Submitted by: Vladimir Ivanov <wawa yandex-team.ru> [2]
than just deleting them. Also add comments about why we do this.
Given the current behavior of delete_child, I don't think this changes
anything. It just feels cleaner.
dereferencing) since a NULL value would be a bug here.
Note: Both affected functions look very similar. A refactoring may
be beneficial.
CID: 483, 485
Found with: Coverity Prevent(tm)
Discussed with: ariff
MFC after: 5 days
needed here, except there's a bug which results in detaching the device
twice.
Move the NULL pointer check to the beginning of the function and convert
it into a KASSERT.
CID: 420
Found with: Coverity Prevent(tm)
Discussed with: ariff
MFC after: 5 days
Control) devices as console. These are microcontrollers which are either
on-board or part of an add-on card and provide terminal server, remote
power switch and monitoring functionality. For console usage these are
connected to the rest of the system via a SCC or an UART. This commit adds
support for the following variants (corresponds to what 'input-device' and
'output-device' have to be set to):
rsc found on-board in E250 and supposedly some Netra, connected
via a SAB82532, com. parameters can be determined via OFW
rsc-console RSC card found in E280R, Fire V4x0, Fire V8x0, connected
via a NS16550, hardwired to 115200 8N1
lom-console LOMlite2 card found in Netra 20/T4, connected via a NS16550,
hardwired to 9600 8N1
- Add my copyright to uart_cpu_sparc64.c as I've rewritten about one third
of that file over time.
Tested on: E250, E280R
Thanks to: dwhite@ for providing access to an E280R
OK'ed by: marcel
MFC after: 1 week
casting a structure to a uint32_t *. Many drivers in the tree do this, but
I'll not update them until these changes can be reviewed by the pedantic
standards folks.
