on x86 and use that to implement stop_emulating() in the fpu/npx code.
Reimplement start_emulating() in the non-XEN case by using load_cr0() and
rcr0() instead of the 'lmsw' and 'smsw' instructions. Intel explicitly
discourages the use of 'lmsw' and 'smsw' on 80386 and later processors in
the description of these instructions in Volume 2 of the ADM.
Reviewed by: kib
MFC after: 1 month
switch to its vnet before calling ether_ifdetach(). Otherwise if the
second half resides in a different vnet, if_detach() silently fails
leaving a stale pointer in V_ifnet list, and the system crashes trying
to access this pointer later.
Another solution could be not to allow to destroy epair unless both
ends are in the home vnet.
Discussed with: bz
Tested by: delphij
The last 12 bits of the limit registers have to be set to 1. These
bits are not significant in bridge BARs and are 0 on read, but the
bits are valid in the swap limit register and needs to be set.
to attach to the process, it is surprising that the process is resumed
without inputting any gdb commands, however ptrace manual said:
The tracing process will see the newly-traced process stop and may
then control it as if it had been traced all along.
But the current code does not work in this way, unless traced process
received a signal later, it will continue to run as a background task.
To fix this problem, just send signal SIGSTOP to the traced process after
we resumed it, this works like that you are attaching to a running process,
it is not perfect but better than nothing.
- Add -P option to support PID file. When -a is specified /var/run/rarpd.pid
is used, and when an interface is specified /var/run/rarpd.<ifname>.pid is
used by default.
The AR93xx and later chips support two RX FIFO queues - a high and low
priority queue.
For legacy chips, just assume the queues are high priority.
This is inspired by the reference driver but is a reimplementation of
the API and code.
AR93xx receive descriptors.
This isn't entirely complete - the AR93xx and later descriptors
don't have a link/buffer pointer; the descriptor contents just
start.
implementation of RFC 3484 for this purpose for a long time and "prefer_source"
was never implemented actually. ND6_IFF_PREFER_SOURCE macro is left intact.
Pass only FEXEC (instead of FREAD|FEXEC) in fgetvp_exec. _fget has to check for
!FWRITE anyway and may as well know about FREAD.
Make _fget code a bit more readable by converting permission checking from if()
to switch(). Assert that correct permission flags are passed.
In collaboration with: kib
Approved by: trasz (mentor)
MFC after: 6 days
X-MFC: with r238220
up and running to service interrupts. This is especially important
when the firmware has bound interrupts to CPUs, like for the SGI
Altix 350. We wake up APs at SI_SUB_CPU time and they sit and spin
until we unleash them, so there's nothing fundamentally different
from a MD perspective.
While here return EBADF for descriptors opened for writing (previously it was ETXTBSY).
Add fgetvp_exec function which performs appropriate checks.
PR: kern/169651
In collaboration with: kib
Approved by: trasz (mentor)
MFC after: 1 week
setting in the igb and em driver. This was necessitated by
a shared code change that I was given late in the game, a data
type changed from bool to int, in the last update I dealt with
it by a cast, but it was pointed out (thanks jhb) that there
was a potential problem with this. John suggested this safer
approach, and it is fine with me...
MFC after:2 days (to catch the 9.1 update)
inactive queue, unless busy page is found.
Dropping the mutex often should allow the other lock acquires to
proceed without waiting for whole inactive scan to finish. On machines
with lot of physical memory scan often need to iterate a lot before it
finishes or finds a page which requires laundring, causing high
latency for other lock waiters.
Suggested and reviewed by: alc
MFC after: 3 weeks
