for the 8169S, according to my sample board. The RealTek Linux driver
mentions 0x00800000. I'm assigning this to the 8110S until I get
more info on it. (The (preliminary) RealTek docs only say that 8169S/8110S
chips will have some combination of those two bits set, but doesn't say
exactly what bit combination goes with which chip variant.)
rl(4) driver and put it in a new re(4) driver. The re(4) driver shares
the if_rlreg.h file with rl(4) but is a separate module. (Ultimately
I may change this. For now, it's convenient.)
rl(4) has been modified so that it will never attach to an 8139C+
chip, leaving it to re(4) instead. Only re(4) has the PCI IDs to
match the 8169/8169S/8110S gigE chips. if_re.c contains the same
basic code that was originally bolted onto if_rl.c, with the
following updates:
- Added support for jumbo frames. Currently, there seems to be
a limit of approximately 6200 bytes for jumbo frames on transmit.
(This was determined via experimentation.) The 8169S/8110S chips
apparently are limited to 7.5K frames on transmit. This may require
some more work, though the framework to handle jumbo frames on RX
is in place: the re_rxeof() routine will gather up frames than span
multiple 2K clusters into a single mbuf list.
- Fixed bug in re_txeof(): if we reap some of the TX buffers,
but there are still some pending, re-arm the timer before exiting
re_txeof() so that another timeout interrupt will be generated, just
in case re_start() doesn't do it for us.
- Handle the 'link state changed' interrupt
- Fix a detach bug. If re(4) is loaded as a module, and you do
tcpdump -i re0, then you do 'kldunload if_re,' the system will
panic after a few seconds. This happens because ether_ifdetach()
ends up calling the BPF detach code, which notices the interface
is in promiscuous mode and tries to switch promisc mode off while
detaching the BPF listner. This ultimately results in a call
to re_ioctl() (due to SIOCSIFFLAGS), which in turn calls re_init()
to handle the IFF_PROMISC flag change. Unfortunately, calling re_init()
here turns the chip back on and restarts the 1-second timeout loop
that drives re_tick(). By the time the timeout fires, if_re.ko
has been unloaded, which results in a call to invalid code and
blows up the system.
To fix this, I cleared the IFF_UP flag before calling ether_ifdetach(),
which stops the ioctl routine from trying to reset the chip.
- Modified comments in re_rxeof() relating to the difference in
RX descriptor status bit layout between the 8139C+ and the gigE
chips. The layout is different because the frame length field
was expanded from 12 bits to 13, and they got rid of one of the
status bits to make room.
- Add diagnostic code (re_diag()) to test for the case where a user
has installed a broken 32-bit 8169 PCI NIC in a 64-bit slot. Some
NICs have the REQ64# and ACK64# lines connected even though the
board is 32-bit only (in this case, they should be pulled high).
This fools the chip into doing 64-bit DMA transfers even though
there is no 64-bit data path. To detect this, re_diag() puts the
chip into digital loopback mode and sets the receiver to promiscuous
mode, then initiates a single 64-byte packet transmission. The
frame is echoed back to the host, and if the frame contents are
intact, we know DMA is working correctly, otherwise we complain
loudly on the console and abort the device attach. (At the moment,
I don't know of any way to work around the problem other than
physically modifying the board, so until/unless I can think of a
software workaround, this will have do to.)
- Created re(4) man page
- Modified rlphy.c to allow re(4) to attach as well as rl(4).
Note that this code works for the sample 8169/Marvell 88E1000 NIC
that I have, but probably won't work for the 8169S/8110S chips.
RealTek has sent me some sample NICs, but they haven't arrived yet.
I will probably need to add an rlgphy driver to handle the on-board
PHY in the 8169S/8110S (it needs special DSP initialization).
we actually use. Originally, the code reserved 0x8000 to 0x80ff inclusive
which on my hardware conflicts with the acpi timer. This broke the amdpm
driver since it was actually given ports 0x800c to 0x810b (which should
not have happened, IMHO).
This also allows us to considerably simplify the handling of the nForce
smb driver, removing the need for a separate nfpm driver. With this, SMB
accesses appear to work on my Tyan Tiger MP board. Your mileage may vary.
In particular, the nForce changes have not been tested.
We can't update the device description in attach (why not ?), so
we device_print() what we find.
Conditionalize the short cable fix on this being older than rev 16A.
Call device_printf() when we apply short cable fix.
Include interrupt hold-off setting for rev 16+ under "#ifdef notyet"
The device_printf()'s will go under bootverbose once the various
issues have settled a bit.
METEORSSIGNAL ioctl. Applications use this ioctl with the value
METEOR_SIG_MODE_MASK (0xFFFF0000, -65536) to reset signal delivery,
but revision 1.126 caused the driver to return EINVAL in this case.
Interestingly, the same METEORSSIGNAL ioctl in the meteor driver uses
0 to reset signal delivery.
This commit allows METEOR_SIG_MODE_MASK as a synonym for 0 in the
bktr driver, and restructures the code a bit so that it is otherwise
identical between the bktr and meteor drivers.
case, a "Vortex86" mini PC), the PCI device ID value in the EEPROM (0x8100)
does not agree with the PCI device ID returned by pci_get_device() (0x8139).
This means that while rl_probe() matches the device, rl_attach() doesn't.
Work around this by adding an entry to the rl_devs table for the 8100 with
a device ID of 0x8100.
Also, get rid of extra instance of __FBSDID(). One is enough.
multi-fragment transmission. I'm not sure if this is a bug or a requirement
that I overlooked with going through the documentation, but the sample
8169 NIC that I have seems to require it at least some of the time or
else it botches TCP checksums on segments that span multiple descriptors.
ioctls.
In the particular case of ptrace(), this commit more-or-less reverts
revision 1.53 of sys_process.c, which appears to have been erroneous.
Reviewed by: iedowse, jhb
word between the 8139C+ and the 8169. The 8139C+ has a 'frame alignment
error bit' (bit 27) but the 8169 does not. Rather than simply mark this
bit as reserved, RealTek removed it completely and shifted the remaining
status bits one space to the left. This was causing rl_rxeofcplus()
to misparse the error and checksum bits.
To workaround this, rl_rxeofcplus() now shifts the rxstat word one
bit to the right before testing any of the status bits (but after
the frame length has been extracted).
note the existence of the 8169S and 8110S components. (The 8169
is just a MAC, the 8169S and 8110S contain both a MAC and PHY.)
- Properly handle list and buffer addresses as 64-bit. The RX and
TX DMA list addresses should be bus_addr_t's. Added RL_ADDR_HI()
and RL_ADDR_LO() macros to obtain values for writing into chip
registers.
- Set a slightly different TIMERINT value for 8169 NICs for improved
performance.
- Change left out of previous commit log: added some additional
hardware rev codes for other 10/100 chips and for the 8169S/8110S
'rev C' gigE MACs.
- Fix a bug in rl_dma_map_desc(): set the 'end of ring' bit in the
right descriptor (DESC_CNT - 1, not DESC_CNT). The 8139C+ is limited
to 64 descriptors and automatically wraps at 64 descriptors even
if the EOR bit isn't set, but the 8169 NIC can have up to 1024
descriptors per ring, so we must set the wrap point in the right
place.
- RealTek moved the RL_TIMERINT register from offset 0x54 to 0x58 in
the 8169 -- account for this.
- Added rl_gmii_readreg() and rl_gmii_writereg() routines.
- Fix rl_probe() to deal with the case where the base type is
not RL_8139.
The next step is to add jumbo buffer support.
Tested with the Xterasys XN-152 NIC (hard to beat $29 for a gigE NIC).
mainly to quiet a warning emitted by GCC 3.3 about comparing
a variable to a value which is larger than the former can hold.
The value was checked to make sure the `np->squeue' array is
not accessed behind its boundary.
This worked due to possibly accidental truncation when
(np->squeueput + 1) was larger than or equal to MAX_START (256)
when it was assigned to `qidx'.
`qidx' is used to hold the next position in the start queue
for an insertion. The new type was chosen because some other
code in the function ncr_freeze_devq() also uses plain integers
to hold those indices.
Wrapped the line after the closing parenthesis of an `if'
condition.
sis_ioctl() was called, so one had to use ifconfig each time the cable got
plugged in to be able to use the connection.
Do it a better way now, add a "in_tick" field in the softc structure,
call timeout() in sis_tick() and don't call it in sis_init() if in_tick is
non-zero.
Reported by: Landmark Networks
Pointy hat to: cognet
Some of the calls to bus_dmamap_sync() were syncing the DMA descriptor
ring maps using the mbuf tag, when they should have been using the
descriptor ring tag instead.
series, the 8139C+ has a descriptor-based DMA mechanism, and its
performance is actually pretty respectable. Note: the 8139D chip does
not support C+ mode. Only the 8139C+ and 8169 gigE chips support C+ mode.
Supported features:
- RX and TX checksum offload
- hardware VLAN tag insertion/extraction
- TX interrupt moderation using the 8139's on-board timer
Everything should be properly busdma'ed and endian-independent, so
things should work ok on non-x86 platforms. Unfortunately, my call
for testers on this code was met with deafening silence, and I don't
have access to any non-x86 FreeBSD boxes at the moment, so this is
speculation.
The device detection code has been cleaned up a little as well
(thanks to Michal Mertl) for the patches.
There are also updates to the rl(4) man page (which I accidentally
checked in before when I updated the dc(4) man page. Oops.)
Todo: finish support for the 8169 gigabit ethernet chip. This
mainly requires writing an rlgphy driver to handle the 8169's built-in
PHY. This will have to wait until I actually get my hands on an 8169
card for testing though. (I still can't find a source for one in the
U.S. Suggestions/pointers welcome.)
- MN-110 10/100 USB ethernet (ADMtek Pegasus II, if_aue)
- MN-120 10/100 cardbus (ADMtek Centaur-C, if_dc)
- MN-130 10/100 PCI (ADMtek Centaur-P, if_dc)
Also update dc(4) man page to mention support for MN-120 and MN-130.
register, present only on 3c90xB and later NICs. This meant that you could
not use a 1500 byte MTU with VLANs on original 3c905/3c900 cards (boomerang
chipset). The boomerang chip does support large frames though, just not
in the same way: you can set the 'allow large frames' bit in the MAC
control register to receive frames up to 4K in size.
Changes:
- Set the 'allow large frames' bit for boomerang chips and increase
the packet size register for cyclone and later chips. This allows
us to use IFCAP_VLAN_MTU on all supported xl(4) NICs.
- Actually set the IFCAP_VLAN_MTU flag in the capabilities word
in xl_attach().
- Change the method used to detect older boomerang chips. My 3c575C
cardbus NIC was being incorrectly identified as 3c90x chip instead
of 3c90xB because the capabilities word in its EEPROM reports
a bizzare value. In addition to checking for the supportsNoTxLength
bit, also check for the absence of the supportsLargePackets bit.
Both of these cases denote a 3c90xB chip.
- Make RX and TX checksums configurable via the SIOCSIFCAP ioctl.
- Avoid an unecessary le32toh() in xl_rxeof(): we already have the
received frame size in the lower 16 bits of rxstat, no need to
read it again.
Tested with 3c905-TX, 3c900-TPO, 3c980C and 3c575C NICs.
to have this driver working on sparc64. It still needs to be made
endian-clean before it can work there.
Special thanks to dragonk@evilcode.net for sending me a dc(4) card so
that I was able to do this work.
Many cheers to all the people that tested this change, thanks to them,
this change shouldn't break anything :-).
Tested by: marcel (i386 and ia64), ru (i386), wilko (alpha),
mbr (i386), wpaul (i386) and
Will Saxon <WillS@housing.ufl.edu> (i386)
BUS_DMA_NOWAIT flag, since the code can't handle this.
- Use NULL, NULL for the lockfunc and lockfuncarg parameters of
bus_dma_tag_create() since deferred loads can't happen now.
forced to do slightly bogus power state manipulation. However, this
is one of those features that is preventing further progress, so mark
them as BURN_BIRDGES like I did for the drivers in sys/dev/...
This, like the other change, are a no-op unless you have BURN_BRIDGES
in your kernel.
Add two new arguments to bus_dma_tag_create(): lockfunc and lockfuncarg.
Lockfunc allows a driver to provide a function for managing its locking
semantics while using busdma. At the moment, this is used for the
asynchronous busdma_swi and callback mechanism. Two lockfunc implementations
are provided: busdma_lock_mutex() performs standard mutex operations on the
mutex that is specified from lockfuncarg. dftl_lock() is a panic
implementation and is defaulted to when NULL, NULL are passed to
bus_dma_tag_create(). The only time that NULL, NULL should ever be used is
when the driver ensures that bus_dmamap_load() will not be deferred.
Drivers that do not provide their own locking can pass
busdma_lock_mutex,&Giant args in order to preserve the former behaviour.
sparc64 and powerpc do not provide real busdma_swi functions, so this is
largely a noop on those platforms. The busdma_swi on is64 is not properly
locked yet, so warnings will be emitted on this platform when busdma
callback deferrals happen.
If anyone gets panics or warnings from dflt_lock() being called, please
let me know right away.
Reviewed by: tmm, gibbs
bit in the EEPROM mode register on. Also, the address must be written
in two 32-bit register accesses instead of 6 8-bit accesses.
Tested with my 8139B cardbus NIC.
PR: kern/35900
Submitted by: Mark Kettenis <kettenis@chello.nl>
mapped I/O mode, we pause for .1 seconds after issuing the reset command
before trying to poll the 'command busy' bit in the status register.
With my 3c575C cardbus NIC, my Sony Picturebook locks up when it tries
to read the status register immediately after the reset. This appears
to be a problem only with certain NICs on certain hardware, but the
added delay should not hurt cards that already work.
This bug seems to have been brought to light by the fact that the xl
driver now defaults to memory mapped I/O mode instead of programmed
I/O mode like it used to. With PIO mode, the delay isn't needed and
everything works (which is why this NIC worked with 5.0-RELEASE but
not 5.1). I suspect that what's happening is that when the chip is
reset, it takes a little while for the memory-mapped decoding logic
to recover. Trying to access the chip's registers during this period
causes an error condition of some kind that wedges the system.
