controllers. There still seems to be some issues with the DRI copying code
for some adapters, at least it doesn't hang the system now. Input would be
appreciated.
PR: 32301
Obtained from: Eric Anhlot <eanholt@gladstone.uoregon.edu>, Joe <joeo@nks.net>
The reason we are required to commit to -current first is so that later
MFC's do not risk the loss of existing bug fixes. Even if this was not
strictly required in -current, it should still be fixed there too.
The reason we are required to commit to -current first is so that later
MFC's do not risk the loss of existing bug fixes. Even if this was not
strictly required in -current, it should still be fixed there too.
mbuf allocation fails, and fix (i hope) a couple of style bugs.
I believe these printf() are extremely dangerous because now they can
occur on every incoming packet and are not rate limited. They were
meant to warn the sysadmin about lack of resources, but now they
can become a nice way to panic your system under load.
Other drivers (e.g. the fxp driver) have nothing like this.
There is a pending discussion on putting this kind of warnings
elsewhere, and I hope we can fix this soon.
underlying unaligned bcopy) on incoming packets that are already
available (albeit unaligned) in a buffer.
The performance improvement varies, depending on CPU and memory
speed, but can be quite large especially on slow CPUs. I have seen
over 50% increase on forwarding speed on the sis driver for the
486/133 (embedded systems), which does exactly the same thing.
The behaviour is controlled by a sysctl variable, hw.dc_quick which
defaults to 1. Set it to 0 to restore the old behaviour.
After running a few experiments (in userland, though) I am convinced
that doing the m_devget() is detrimental to performance in almost
all cases.
Even if your CPU has degraded performance with misaligned data,
the bcopy() in the driver has the same overhead due to misaligment
as the one that you save in the uiomove(), plus you do one extra
copy and pollute the cache.
But more often than not, you do not even have to touch the payload,
e.g. when you are forwarding packets, and even in the often-cited
case of NFS, you often end up passing a pointer to the payload to
the disk controller.
In any case, you can play with the sysctl variable to toggle between
the two behaviours, and see if it makes a difference.
MFC-after: 3 days
have alignment problems.
On small boxes (e.g. the net4501 from Soekris, featuring a 486/133)
this provides huge performance benefits: the peak forwarding rate
with avg.sized packets goes up by 50-70% because of this change
alone. Faster CPUs might benefit less from this change, but in any
case the CPU has better things to do than waste time on useless
memory-to-memory copies.
Several drivers (for Tulip-like cards) might benefit from a similar
change.
Right now the new behaviour is controlled by a sysctl variable,
hw.sis_quick which defaults to 1 (on), you can set it to 0 to
reintroduce the old behaviour (and compare the results). The
variable is only there to show how much you can gain with this
change, it will go away soon.
Also, slightly simplify the code to initialize the ring buffers,
and remove a couple of dangerous printf's which could trigger on
any packet in case of mbuf shortage.
MFC-after: 3 days
idle and the driver would not detect the event, requiring userland
to cycle the interface to bring it up again.
The fix consists in adding SIS_IMR_RX_IDLE to the interrupt mask and
add a command in sis_intr() to restart the receiver when this happens.
While at it, make the test of status bits more efficient.
in the 21143, instead of giving priority to the receive unit.
This gives a 10-15% performance improvement in the forwarding rate
under heavy load.
Reviewed-by: Bill Paul
Jonathon Lemon's driver (gx) is at least as fast and has more features
and is likely to be better supported.
It is also possible that Intel might support this chipset in FreeBSD
with their own driver. Somewhat secretive and furtive rumblings from
certain Yahoo employees have indicated that this might happen soon.
I'm a little unhappy at the lack of discussion on the net list about
this, or on developers, or on hackers, or the lack of mention on
audit. This then leaves me to try and figure out the right thing
to do.
I've concluded that the right thing to do is to remove wx from FreeBSD,
as this is probably best for FreeBSD.
What the heck, the OpenBSD version will benefit.
1. Add wx_txint_delay as a tunable (defaults to 5000 now, or ~5ms) and switch
to using delayed TXDW interrupts. Since the chip continues to reload the
TIDV with this value for each descriptor written back, this allows continued
deferral of the actual interrupt until the last packet completes (assuming
that 5ms between multiple packets transmitting is reasonable).
2. Add two other SYSCTL entities:
hw.wx.dump_stats
hw.wx.clear_stats
to be used, hackey hackey, to get the watchdog routine to dump/clear
the current softc statistics.
Usage would be:
sysctl -w hw.wx.dump_stats=UNIT
to cause the current stats to be dumped for UNIT.
3. Attempt to clean up wx_detach routine so we don't panic. Well, things
still panic, but given that the code is just like other NIC drivers,
I suspect it's actually something elsewhere, like e1000phy, that's actually
blowing up.
4. Skip the entire test for runt packets- after doing somet thinking
and experimenting, I believe that the chip only doesn't like it if
the whole frame to xmit is < 16 bytes- each TFD can be some fragment
of that. This should improve performance a chunk because of all of the
(14 byte ETHERHEADER + DATA) mbuf chains.
5. Keep track of total frame length. Try not to xmit an odd byte frame-
this is supposed to get around some dumb Cisco switch problems.
6. On the last packet, also set Interrupt Delay && Report Packet Sent
(see #1 above)
7. Attempt to do xmit garbage collection *first* in order to avoid setting
IFF_OACTIVE if at all possible.
MFC after: 1 week
We only support the size of frame we are currently allocating, which
is MCLBYTES - sizeof (struct ether_header) usable, so don't set an
MTU that would go over this.
it now really gets in the way.
This allows us to fix several problems- not least of which was problems
of ordering about when you'd have a device softc for an miibus child
available or not. Move some steps of things around.
Put the ifnet/arpcom structure at the head of the softc (PR 29249).
Don't do tx gc in the interrupt service routine- that seems to make
things a bit more efficient.
Enable jumbo support by default- but this version of 'jumbo' is broken
because it really is just using multiple tfd/rfd's to match a packet,
which will never be > CLSIZE anyway.
This should begin the first steps toward cleaning this driver up.
PR: 29249
MFC after: 1 week
seems to set up memory spaces correctly. This change actually did work for
me using -STABLE, XFree86 4.0.3 ~ some snapshot of DRI awhile back. I sent
mail to dfr to no avail, perhaps someone else would like to test it with
DRI.
Anyway, people have been nagging me about this change for awhile, so here's
the commit.
amdpm(4) and smb(4).
This device can be used with userland programs such as sysutils/lmmon
to retrieve sensor information from the motherboard.
PR: kern/23989
Obtained from: Matthew C. Forman <mcf@dmu.ac.uk>
Based on: alpm(4)
Note ALL MODULES MUST BE RECOMPILED
make the kernel aware that there are smaller units of scheduling than the
process. (but only allow one thread per process at this time).
This is functionally equivalent to teh previousl -current except
that there is a thread associated with each process.
Sorry john! (your next MFC will be a doosie!)
Reviewed by: peter@freebsd.org, dillon@freebsd.org
X-MFC after: ha ha ha ha
laptops with this chip should test this and report back as I don't have
access to this hardware myself. People with -stable systems should try
the patch at:
http://www.freebsd.org/~wpaul/conexant.patch.gz
Submitted by: Phil Kernick <Phil@Kernick.org>
dual function card. It needs pretty much the same flags as the 656C,
except that it seems to need both the INVERT_MII_PWR and INVERT_LED_PWR
flags set. Tested with cardbus in -current as of today.
Also added support for the 3c656, which looks to be the same as
the 656B, except it doesn't need the EEPROM_8BIT flag. I think. This
one is untested, but the added support should not break any of the
other cards.
prevent/workaround TX lockups in this driver. The secret seems to be to
not let the TX DMA queue become too full. If we have too many packets
in the queue, we should wait for them to drain a bit before trying to
queue more. This should prevent the lockup from occurring, and if it
does occur, there is special code in sf_start() to kick the NIC in the
head and get it going again.
Special thanks to Glen Neff for helping me test this fix.
night of testing before merging to -stable.
Also added to code to detect TX underruns and automatically increase the
TX threshold to avoid them. Carefully placed diagnostig printf() about
this under #ifdef DIAGNOSTIC to avoid getting any panicky e-mails from
confused users, like I always do with the xl and dc drivers.
calling vtophys() and contigmalloc()/contigfree() directly. Hopefully,
I have shaken out all of the problems with busdma on the alpha now.
(Everything seems to work as expected.)
Also, change the max RX DMA limit to 1024 bytes instead of "unlimited,"
as the latter seems not to work correctly on the alpha that I tested.
(At 100Mbps, all attempts to receive frames yield RX errors.)
common_attach is wrong as common attach initialize some fileds used by
mediainit routine. This was hard to notify because loading driver as kld
lead to mediainit routine being called after common_attach, though probe_phy
is called before.
MFC after: 1 week
never completed" message. The RX reset takes longer complete than it
used to, a lot longer in fact than xl_wait() is prepared to wait.
When we do the RX reset in xl_reset(), this cases xl_wait() to time out
and whine. We wait a little extra time now after the RX reset, which
should silence the warning.
Thanks to obrien for finally getting me a box with a NIC that
causes this problem for me to tinker with.
a bunch of frames. In this case, the dc_link flag is cleared, and dc_start()
stops draining the if_snd send queue, which results in lots of 'no buffers
available' errors being reported to applications. The whole idea behind
not draining the send queue until the link comes up was to avoid having
the gratuitous ARP being lost while we're waiting for autoneg to complete
after the interface is first brought up. As an optimization, change the
test in dc_start() so that we only bail if dc_link is not set _and_ there
are less than 10 packets in the send queue. If the queue has many frames
in it, we need to drain them. If the queue has a small number of frames
in it, we can hold off on sending them until the link comes up.
MFC after: 1 week
something: offset into the first mbuf of the target chain before copying
the source data over.
Make drivers using m_devget() with a first argument "data - ETHER_ALIGN"
to use the offset argument to pass ETHER_ALIGN in. The way it was previously
done is potentially dangerous if the source data was at the top of a page
and the offset caused the previous page to be copied (if the
previous page has not yet been appropriately mapped).
The old `offset' argument in m_devget() is not used anywhere (it's always
0) and dates back to ~1995 (and earlier?) when support for ethernet trailers
existed. With that support gone, it was merely collecting dust.
Tested on alpha by: jlemon
Partially submitted by: jlemon
Reviewed by: jlemon
MFC after: 3 weeks
412: warning: long unsigned int format, unsigned int arg (arg 3)
418: warning: long unsigned int format, unsigned int arg (arg 3)
424: warning: long unsigned int format, unsigned int arg (arg 3)
PCN_BCR_CLRBIT(sc, PCN_BCR_MIICTL, PCN_MIICTL_DANAS);
should be:
PCN_BCR_SETBIT(sc, PCN_BCR_MIICTL, PCN_MIICTL_DANAS);
Turning this bit on is what disables MII autoneg, not turning it off.
Without this, manually setting the media doesn't work.
Noticed by: Jim Browne <jbrowne@jbrowne.com>
setting the 'max packet size' register in window 3. This only
works for cards based on the cyclone or newer chipsets (i.e. it
won't work with the original 3c905/boomerang cards).
There is a trick which will work with the boomerang, which is to turn
on the 'large packets ok' bit in the MAC control register, however this
lets the chip accept any frame up to 4K in length, which is larger than
the mbuf cluster buffers we use to receive frames. If somebody sends us
such a frame and the chip DMAs it to us, it could write past the end
of the cluster buffer and clobber something.
PR: kern/27742
vm_mtx does not recurse and is required for most low level
vm operations.
faults can not be taken without holding Giant.
Memory subsystems can now call the base page allocators safely.
Almost all atomic ops were removed as they are covered under the
vm mutex.
Alpha and ia64 now need to catch up to i386's trap handlers.
FFS and NFS have been tested, other filesystems will need minor
changes (grabbing the vm lock when twiddling page properties).
Reviewed (partially) by: jake, jhb
of the pcic class of devices. Go ahead and move it to the "usual"
place. I say "usual" in quotes since it isn't exactly right (not in
dev/blah), but it is closer than before.
much more often that expected and negatively impact performance when
running at 100mbps. I need to figure out if there's a better way to
handle this, but for now this shouldn't hurt anything.
use TAILQ macros. The sk_attach_xmac() routine calls sk_init_xmac()
before doing the transceiver probe, but *before* ether_ifattach()
is called. This causes sk_init_xmac() to call sk_setmulti(), which
tries to do a TAILQ_FOREACH(), which it can't do because ether_ifattach()
hasn't done a TAILQ_INIT() yet. This causes a NULL pointer dereference
and panic in sk_setmulti() at driver load/initialization time.
Fixed by calling ether_ifattach() before the MII probe.
The code in RELENG_4 still uses the old way of enumerating the
multicast list and doesn't have this problem. Yet.
The constant I was using was correct, but I mislabeled it as 256K when
it should have been 512K. This doesn't actually change the code, but
it clarifies things somewhat.
Submitted by: Chuck Cranor <chuck@research.att.com>
parts. This is based on the newcard code that turns it off :-). We
can now reboot after NEWCARD or Windows and have OLDCARD work. Add
support for the RL5C466 while I'm at it.
Treat TI1031 the same as the CLPD6832. It doesn't work yet, but sucks
less than it did before.
Also add a few #defines for other changes in the pipe.
1. Pick up MII/PHY support for Livengood copper part (10/100/1000) from
Parag Patel. It was a fairly complete but not quite platform independent
job.
2. Finish silly offset differences that LIVENGOOD vs. WISEMAN registers
have (so the !)$*!)$*!$ fiber LIVENGOOD now works too).
3. Ansify the source.
So- we now suppor tthe PRO1000F and PRO1000T adapters.
1. The offsets for some registers change in LIVENGOOD. Gratuitously.
2. Define LIVENGOOD and LIVENGOOD_CU part numbers. Add some more
specific LIVENGOOD defaults.
3. Add definitions for PHY support for the copper LIVENGOOD part
(10/100/1000).
interface on this chip is compatable with the PIIX4. The catch is that
this interferes with isab0 which wants to attach to the same PCI node.
It seems to work, but we only tested it on systems with no ISA cards.
in vr_init(). The VIA Rhine chip happens to be able to automatically
read its station address from the EEPROM automatically when reset,
so you don't need to program the filter if you want to keep using the
factory default address, but if you want to change it with "ifconfig vr0
ether xx:xx:xx:xx:xx:xx" then we need to manually set it in the init
routine.
in VMware reports 0x00000000 in the PCI subsystem ID register, but
0x10001000 when you read the mirror registers in I/O space. This causes
pcn_probe() to think it's found a card in 32-bit mode, and performing
a 32-bit I/O access makes on a 16-bit port makes VMware go boom. Special
case the 0x10001000 value until somebody at VMware grows a clue.
Finally discovered by: Andrew Gallatin
- Use pci_get_powerstate()/pci_set_powerstate() in all the other drivers
that need them so we don't have to fiddle with the PCI power management
registers directly.
- Use pci_enable_busmaster()/pci_enable_io() to turn on busmastering and
PIO/memory mapped accesses.
- Add support to the RealTek driver for the D-Link DFE-530TX+ which has
a RealTek 8139 with its own PCI ID. (Submitted by Jason Wright)
- Have the SiS 900/National DP83815 driver be sure to disable PME
mode in sis_reset(). This apparently fixes a problem on some
motherboards where the DP83815 chip fails to receive packets.
(Submitted by Chuck McCrobie <mccrobie@cablespeed.com>)
case there is nothing to do. This happens normally when the card shares
the interrupt line with other devices.
This code saves a couple of microseconds per interrupt even on a
fast CPU. You normally would not care, except under heavy tinygram
traffic where you can have some 50-100.000 interrupts per second...
On passing, correct a spelling error.
mtx_enter(lock, type) becomes:
mtx_lock(lock) for sleep locks (MTX_DEF-initialized locks)
mtx_lock_spin(lock) for spin locks (MTX_SPIN-initialized)
similarily, for releasing a lock, we now have:
mtx_unlock(lock) for MTX_DEF and mtx_unlock_spin(lock) for MTX_SPIN.
We change the caller interface for the two different types of locks
because the semantics are entirely different for each case, and this
makes it explicitly clear and, at the same time, it rids us of the
extra `type' argument.
The enter->lock and exit->unlock change has been made with the idea
that we're "locking data" and not "entering locked code" in mind.
Further, remove all additional "flags" previously passed to the
lock acquire/release routines with the exception of two:
MTX_QUIET and MTX_NOSWITCH
The functionality of these flags is preserved and they can be passed
to the lock/unlock routines by calling the corresponding wrappers:
mtx_{lock, unlock}_flags(lock, flag(s)) and
mtx_{lock, unlock}_spin_flags(lock, flag(s)) for MTX_DEF and MTX_SPIN
locks, respectively.
Re-inline some lock acq/rel code; in the sleep lock case, we only
inline the _obtain_lock()s in order to ensure that the inlined code
fits into a cache line. In the spin lock case, we inline recursion and
actually only perform a function call if we need to spin. This change
has been made with the idea that we generally tend to avoid spin locks
and that also the spin locks that we do have and are heavily used
(i.e. sched_lock) do recurse, and therefore in an effort to reduce
function call overhead for some architectures (such as alpha), we
inline recursion for this case.
Create a new malloc type for the witness code and retire from using
the M_DEV type. The new type is called M_WITNESS and is only declared
if WITNESS is enabled.
Begin cleaning up some machdep/mutex.h code - specifically updated the
"optimized" inlined code in alpha/mutex.h and wrote MTX_LOCK_SPIN
and MTX_UNLOCK_SPIN asm macros for the i386/mutex.h as we presently
need those.
Finally, caught up to the interface changes in all sys code.
Contributors: jake, jhb, jasone (in no particular order)
chipset. The MAC address is stored in the APC CMOS RAM and we have to
commit trememdous evil in order to read it. The code to do this is only
activated on the i386 platform. Thanks to Cameron Grant for providing
access to a test box for me to tinker with.
This will fix the problem where the sis driver ends up with a station
address of 00:00:00:00:00:00 on boards that use the 630E chipset.
an override as a loader settable variable (fxp_iomap). fxp_iomap is
a bitmap of fxp units that should be configured to use PCI I/O space
in stead of PCI Memory space.
Reviewed by: Kees Jan Koster <dutchman@tccn.cs.kun.nl>, dg@freebsd.org
MFC'ed i due time. I can't test it under current right now because
netgraph seems to do unethical things with mutexes.
musycc:
Add status per channel.
Reduce printf chattyness
Keep error counters line if_mn does.
Increase descriptor count.
if_mn:
Support experimental unframed E1 lines.
These two drivers should share more code relating to framed channelized
TDM media in general (T1/E1/E3/T3, Sonet). Anyone interested email me.
if_vr: handle the case where vr_encap() returns failure: bust out of the
packet sending loop instead of panicking. Also add some missing
newlines to some printf()s.
if_dc: The miibus_read and miibus_write methods keep swapping in and
out of MII mode by fiddling with CSR6 for cards with MII PHYs.
This is a hack to support the original Macronix 98713 card which
has built-in NWAY that uses an MII-like management interface
even though it uses serial transceivers. Conditionalize this
so that we only do this on 98713 chips, since it does bad things
to genuine tulip chips (and maybe other clones).
All calls to mtx_init() for mutexes that recurse must now include
the MTX_RECURSE bit in the flag argument variable. This change is in
preparation for an upcoming (further) mutex API cleanup.
The witness code will call panic() if a lock is found to recurse but
the MTX_RECURSE bit was not set during the lock's initialization.
The old MTX_RECURSE "state" bit (in mtx_lock) has been renamed to
MTX_RECURSED, which is more appropriate given its meaning.
The following locks have been made "recursive," thus far:
eventhandler, Giant, callout, sched_lock, possibly some others declared
in the architecture-specific code, all of the network card driver locks
in pci/, as well as some other locks in dev/ stuff that I've found to
be recursive.
Reviewed by: jhb
This version is functional and is aproaching solid..
notice I said APROACHING. There are many node types I cannot test
I have tested: echo hole ppp socket vjc iface tee bpf async tty
The rest compile and "Look" right. More changes to follow.
DEBUGGING is enabled in this code to help if people have problems.
This is because calls with M_WAIT (now M_TRYWAIT) may not wait
forever when nothing is available for allocation, and may end up
returning NULL. Hopefully we now communicate more of the right thing
to developers and make it very clear that it's necessary to check whether
calls with M_(TRY)WAIT also resulted in a failed allocation.
M_TRYWAIT basically means "try harder, block if necessary, but don't
necessarily wait forever." The time spent blocking is tunable with
the kern.ipc.mbuf_wait sysctl.
M_WAIT is now deprecated but still defined for the next little while.
* Fix a typo in a comment in mbuf.h
* Fix some code that was actually passing the mbuf subsystem's M_WAIT to
malloc(). Made it pass M_WAITOK instead. If we were ever to redefine the
value of the M_WAIT flag, this could have became a big problem.
claimed that their Intel NIC is comatose after a warm boot from Windoze.
This is most likely due to the card getting put in the D3 state. This
should bring it back to life.
PCI code. This saves each driver from having to grovel around looking
for the right registers to twiddle.
I should eventually convert the other PCI drivers to do this; for now,
these three are ones which I know need power state handling.
format version number. (userland programs should not need to be
recompiled when the netgraph kernel internal ABI is changed.
Also fix modules that don;t handle the fact that a caller may not supply
a return message pointer. (benign at the moment because the calling code
checks, but that will change)
- Break out the /dev/pci driver into a separate file.
- Kill the COMPAT_OLDPCI support.
- Make the EISA bridge attach a bit more like the old code; explicitly
check for the existence of eisa0/isa0 and only attach if they don't
already exist. Only make one bus_generic_attach() pass over the
bridge, once both busses are attached. Note that the stupid Intel
bridge's class is entirely unpredictable.
- Add prototypes and re-layout the core PCI modules in line with
current coding standards (not a major whitespace change, just moving
the module data to the top of the file).
- Remove redundant type-2 bridge support from the core PCI code; the
PCI-CardBus code does this itself internally. Remove the now
entirely redundant header-class-specific support, as well as the
secondary and subordinate bus number fields. These are bridge
attributes now.
- Add support for PCI Extended Capabilities.
- Add support for PCI Power Management. The interface currently
allows a driver to query and set the power state of a device.
- Add helper functions to allow drivers to enable/disable busmastering
and the decoding of I/O and memory ranges.
- Use PCI_SLOTMAX and PCI_FUNCMAX rather than magic numbers in some
places.
- Make the PCI-PCI bridge code a little more paranoid about valid
I/O and memory decodes.
- Add some more PCI register definitions for the command and status
registers. Correct another bogus definition for type-1 bridges.
This clears out my outstanding netgraph changes.
There is a netgraph change of design in the offing and this is to some
extent a superset of soem of the new functionality and some of the old
functionality that may be removed.
This code works as before, but allows some new features that I want to
work with and evaluate. It is the basis for a version of netgraph
with integral locking for SMP use.
This is running on my test machine with no new problems :-)
- Move PCI core code to dev/pci.
- Split bridge code out into separate modules.
- Remove the descriptive strings from the bridge drivers. If you
want to know what a device is, use pciconf. Add support for
broadly identifying devices based on class/subclass, and for
parsing a preloaded device identification database so that if
you want to waste the memory, you can identify *anything* we know
about.
- Remove machine-dependant code from the core PCI code. APIC interrupt
mapping is performed by shadowing the intline register in machine-
dependant code.
- Bring interrupt routing support to the Alpha
(although many platforms don't yet support routing or mapping
interrupts entirely correctly). This resulted in spamming
<sys/bus.h> into more places than it really should have gone.
- Put sys/dev on the kernel/modules include path. This avoids
having to change *all* the pci*.h includes.
place the LOCKing macros within the areas within if_wxvar.h that
is set aside for them. Put any platform specific data also in those
areas.
For ease of maintenance purposes, merge in the OpenBSD version codebase here.
on. So stop failing the attach if the IRQ is unassigned. With this
patch, I can now boot with PNP-OS YES in my BIOS no differently than
PNP-OS NO (which is a good thing since Windows hangs with PNP-OS NO).
Obtained from: msmith
like the args to the config space accessors these functions replaced.
This reduces the likelyhood of overflow when the args are used in
macros on the alpha. This prevents memory management faults when
probing the pci bus on sables, multias and nonames.
Approved by: dfr
Tested by: Bernd Walter <ticso@cicely8.cicely.de>
the interface to use callout_* instead of timeout(). Also add an
IS_MPSAFE #define (currently off) which will mark the driver as mpsafe
to the upper layers.
before adding/removing packets from the queue. Also, the if_obytes and
if_omcasts fields should only be manipulated under protection of the mutex.
IF_ENQUEUE, IF_PREPEND, and IF_DEQUEUE perform all necessary locking on
the queue. An IF_LOCK macro is provided, as well as the old (mutex-less)
versions of the macros in the form _IF_ENQUEUE, _IF_QFULL, for code which
needs them, but their use is discouraged.
Two new macros are introduced: IF_DRAIN() to drain a queue, and IF_HANDOFF,
which takes care of locking/enqueue, and also statistics updating/start
if necessary.
(identified by the IO map being 256 bytes long instead of 128)
This chip works very unreliably on my Lanner embedded PC with the rl driver.
Lots of watchdog timeouts or poor performance.
Forcing the media type to 10 Meg (ifconfig rl0 media 10baseT/UTP) is a good
workaround.
This looks very similar to the problem reported in PR kern/18790
It is interesting to note that the linux driver has lots of special
case code for this chip.
is already in 32-bit mode, we need to be able to detect this and still
read the chip ID code. Detecting 32-bit mode is actually a little
tricky, since we want to avoid turning it on accidentally. The easiest
way to do it is to just try and read the PCI subsystem ID from the
bus control registers using 16-bit accesses and compare that with the
value read from PCI config space. If they match, then we know we're in
16-bit mode, otherwise we assume 32-bit mode.
16-bit mode. Technically, pcn_probe() is destructive because once the
chip goes into 32-bit mode, the only way to get it out again is a
hardware reset. And once the device is in 32-bit mode, the lnc driver
won't be able to talk to it. So if pcn_probe() is called before the
lnc probe routine, and pcn_probe() rejects the chip as one it doesn't
support, the lnc driver will be SOL.
I don't like this. I think it's a design flaw that you can't switch
the chip out of 32-bit mode once it's selected. The only 'right'
solution is for the pcn driver to support all of the PCI devices
in 32-bit mode, however I don't have samples of all the PCnet series
cards for testing.
pollution in <sys/mutex.h>. This was half fixed in rev.1.3 of
midwayreg.h. The pollution exposed the bug that this driver was using
toy versions of the bus space macros under FreeBSD. Disabling the
toy versions made this driver compile but dependent on the pollution.
There was still a toy version of bus_space_read_1() in unreachable code.
and nobroadcast bits in the mode register and call it both from
pcn_init() and pcn_ioctl(). Sometimes we need to force the state
of the nobroadcast bit after switching out of promisc mode.
them. If we leave garbage in them, the dc_apply_fixup() routine may
try to follow bogus pointers when applying the reset fixup.
Noticed by: Andrew Gallatin
- Add DRIVER_MODULE() declaration to make this driver a
child of cardbus
- Handle different width EEPROMs
The CIS parser still barfs when scanning this card, but it seems to
probe/attach correctly anyway. I can't do a traffic test just yet
since I don't have a proper crossover cable handy.
the offending inline function (BUF_KERNPROC) on it being #included
already.
I'm not sure BUF_KERNPROC() is even the right thing to do or in the
right place or implemented the right way (inline vs normal function).
Remove consequently unneeded #includes of <sys/proc.h>
command register is too aggressive. Revert to the previous behaviour, but
leave the new behaviour available as an undocumented option. It's not
clear what the Right, Right Thing is to do here, but the more conservative
approach is safer.
a RealTek 8139 cardbus device. Unfortunately it doesn't quite work yet
because the CIS parser barfs on it.
Submitted by msmith, with some small tweaks by me.
because it only takes a struct tag which makes it impossible to
use unions, typedefs etc.
Define __offsetof() in <machine/ansi.h>
Define offsetof() in terms of __offsetof() in <stddef.h> and <sys/types.h>
Remove myriad of local offsetof() definitions.
Remove includes of <stddef.h> in kernel code.
NB: Kernelcode should *never* include from /usr/include !
Make <sys/queue.h> include <machine/ansi.h> to avoid polluting the API.
Deprecate <struct.h> with a warning. The warning turns into an error on
01-12-2000 and the file gets removed entirely on 01-01-2001.
Paritials reviews by: various.
Significant brucifications by: bde
the PCI latency timer value to 0x80. Davicom's Linux driver does this,
and it drastically reduces the number of TX underruns in my tests. (Note:
this is done only for the Davicom chips. I'm not sure it's a good idea to
do it for all of them.)
Again, still waiting on confirmation before merging to stable.
DM9100/DM9102 chips. Do not set DC_TX_ONE. The DC_TX_USE_TX_INTR flag
causes dc_encap() to set the 'interrupt on TX completion' bit only
once every 64 packets. This is an attempt to reduce the number
of interrupts generated by the chip. You're supposed to get a 'no more
TX buffers left' interrupt once you hit the last packet whether you
ask for one or not, however it seems the Davicom chip doesn't generate
this interrupt, or at least it doesn't generate it under the same
circumstances. The result is that if you transmit n packets, where
n is less than 64, and then wait 5 seconds, you'll get a watchdog
timeout whether you want one or not. The DC_TX_INTR_ALWAYS causes
dc_encap() to request an interrupt for every frame.
I'm still waiting on confirmation from a couple of users to see if this
fixes their problems with the Davicom DM9102 before I merge this into
-stable, but this fixed the problem for me in my own testing so I'm
willing to make the change to -current right away.
Have if_ti stop "hiding" the softc pointer in the buffer region. Rather,
use the available void * passed to the free routine and pass the softc
pointer through there.
To note: in MEXTADD(), TI_JUMBO_FRAMELEN should probably be TI_JLEN. I left it
unchanged, because this way I'm sure to not damage anything in this respect...
This commit adds support for Xircom X3201 based cardbus cards.
Support for the TDK 78Q2120 MII is also added.
IBM Etherjet, Intel and Xircom cards uses these chips.
Note that as a result of this commit, some Intel/DEC 21143 based cardbus
cards will also attach, but not get link. That is being looked at.
