programmed on the BSP during (early) boot. This makes sure
that the APs get configured the same as the BSP, irrspective
of how FreeBSD was loaded.
2. Make sure to flush the dcache after writing the TLB1 entries
to the boot page. The APs aren't part of the coherency domain
just yet.
3. Set pmap_bootstrapped after calling pmap_bootstrap(). The
FDT code now maps the devices (like OF), and this resulted
in a panic.
4. Since we pre-wire the CCSR, make sure not to map chunks of
it in pmap_mapdev().
Note that setting the PTE_MODIFIED bit based on whether write is possible
is incorrect. We should set PTE_MODIFIED based on whether the access
is a write operation.
implementation specific vs. the common architecture definition.
Bring PPC4XX defines (PSL, SPR, TLB). Note the new definitions under
BOOKE_PPC4XX are not used in the code yet.
This change set is not supposed to affect existing E500 support, it's just
another reorg step before bringing support for E500mc, E5500 and PPC465.
Obtained from: AppliedMicro, Freescale, Semihalf
for variables that live in the boot page.
o Add bp_trace (yes, it's in the boot page) that gets zeroed before we
try to wake a core and to which the core being woken can write markers
so that we know where the core was in case it doesn't wake up. The
boot code does not yet write markers (too follow).
o Disable the boot page translation to allow the last 4K page to be used
for whatever we please. It would get mapped otherwise.
o Fix kernstart in the case of SMP. The start argument is typically page
aligned due to the alignment requirements that come with having a boot
page. The point of using trunc_page is that we get the actual load
address given that the entry point is immediately following the ELF
headers. In the SMP case this ended up exactly 4K after the load
address. Hence subtracting 1 from start.
According to the open firmware standard, finddevice call has to return
a phandle with value of -1 in case of error.
This commit is to:
- Fix the FDT implementation of this interface (ofw_fdt_finddevice) to
return (phandle_t)-1 in case of error, instead of 0 as it does now.
- Fix up the callers of OF_finddevice() to compare the return value with
-1 instead of 0 to check for errors.
- Since phandle_t is unsigned, the return value of OF_finddevice should
be checked with '== -1' rather than '<= 0' or '> 0', fix up these cases
as well.
Reported by: nwhitehorn
Reviewed by: raj
Approved by: raj, nwhitehorn
protected the dirty mask updates. The dirty mask updates are handled
by atomics after the r225840.
Submitted by: alc
Tested by: flo (sparc64)
MFC after: 2 weeks
flags field. Updates to the atomic flags are performed using the atomic
ops on the containing word, do not require any vm lock to be held, and
are non-blocking. The vm_page_aflag_set(9) and vm_page_aflag_clear(9)
functions are provided to modify afalgs.
Document the changes to flags field to only require the page lock.
Introduce vm_page_reference(9) function to provide a stable KPI and
KBI for filesystems like tmpfs and zfs which need to mark a page as
referenced.
Reviewed by: alc, attilio
Tested by: marius, flo (sparc64); andreast (powerpc, powerpc64)
Approved by: re (bz)
to VPO_UNMANAGED (and also making the flag protected by the vm object
lock, instead of vm page queue lock).
- Mark the fake pages with both PG_FICTITIOUS (as it is now) and
VPO_UNMANAGED. As a consequence, pmap code now can use use just
VPO_UNMANAGED to decide whether the page is unmanaged.
Reviewed by: alc
Tested by: pho (x86, previous version), marius (sparc64),
marcel (arm, ia64, powerpc), ray (mips)
Sponsored by: The FreeBSD Foundation
Approved by: re (bz)
o Fix awkward use of braces in combination with mis-indentation.
A mistake, that happened to yield the right behaviour?
o Fix typo in comment.
No functional change.
Approved by: re (blanket)
Juniper's loader is that Juniper's loader maps all of the kernel and
preloaded modules at the right virtual address before jumping into the
kernel. FreeBSD's loader simply maps 16MB using the physical address
and expects the kernel to jump through hoops to relocate itself to
it's virtual address. The problem with the FreeBSD loader's approach is
that it typically maps too much or too little. There's no harm if it's
too much (other than wasting space), but if it's too little then the
kernel will simply not boot, because the first thing the kernel needs
is the bootinfo structure, which is never mapped in that case. The page
fault that early is fatal.
The changes constitute:
1. Do not remap the kernel in locore.S. We're mapped where we need to
be so we can pretty much call into C code after setting up the
stack.
2. With kernload and kernload_ap not set in locore.S, we need to set
them in pmap.c: kernload gets defined when we preserve the TLB1.
Here we also determine the size of the kernel mapped. kernload_ap
is set first thing in the pmap_bootstrap() method.
3. Fix tlb1_map_region() and its use to properly externd the mapped
kernel size to include low-level data structures.
Approved by: re (blanket)
Obtained from: Juniper Networks, Inc
sintrcnt/sintrnames which are symbols containing the size of the 2
tables.
- For amd64/i386 remove the storage of intr* stuff from assembly files.
This area can be widely improved by applying the same to other
architectures and likely finding an unified approach among them and
move the whole code to be MI. More work in this area is expected to
happen fairly soon.
No MFC is previewed for this patch.
Tested by: pluknet
Reviewed by: jhb
Approved by: re (kib)
instead of a PCPU field for curthread. This averts a race on SMP systems
with a high interrupt rate where the thread looking up the value of
curthread could be preempted and migrated between obtaining the PCPU
pointer and reading the value of pc_curthread, resulting in curthread being
observed to be the current thread on the thread's original CPU. This played
merry havoc with the system, in particular with mutexes. Many thanks to
jhb for helping me work this one out.
Note that Book-E is in principle susceptible to the same problem, but has
not been modified yet due to lack of Book-E hardware.
MFC after: 2 weeks
be brought up in the order they are enumerated in the device tree (in
particular, that thread 0 on each core be brought up first). The SLIST
through which we loop to start the CPUs has all of its entries added with
SLIST_INSERT_HEAD(), which means it is in reverse order of enumeration
and so AP startup would always fail in such situations (causing a machine
check or RTAS failure). Fix this by changing the SLIST into an STAILQ,
and inserting new CPUs at the end.
Reviewed by: jhb
o In bare_probe(), change the logic that determines the maximum
number of processors/cores into a switch statement and take
advantage of the fact that bit 3 of the SVR value indicates
whether we're running on a security enabled version. Since we
don't care about that here, mask the bit. All -E versions
are taken care of automatically.
from U-Boot, the kernel is passed a standard argc/argv pair.
The Juniper loader passes the metadata pointer as the second
argument and passes 0 in the first. The FreeBSD loader passes
the metadata pointer in the first argument.
As such, have locore preserve the first 2 arguments in registers
r30 & r31. Change e500_init() to accept these arguments. Don't
pass global offsets (i.e. kernel_text and _end) as arguments to
e500_init(). We can reference those directly.
Rename e500_init() to booke_init() now that we're changing the
prototype.
In booke_init(), "decode" arg1 and arg2 to obtain the metadata
pointer correctly. For the U-Boot case, clear SBSS and BSS and
bank on having a static FDT for now. This allows loading the
ELF kernel and jumping to the entry point without trampoline.
a tendency to grow unwieldy so we may want to revisit this in due
time.
o Simplify the CPU reset function by writing to the reset control
register irrespective of whether the CPU has one and automatically
falling back to the debug control register if we didn't reset the
CPU. The side-effect is that we now properly reset future processors
without first having to add the system version to the list.
U-Boot as found on the P1020RDB doesn't like it when we use entry 1
(for some reason) whereas an older U-Boot doesn't mind if we use entry
0. If anything else, this simplifies the code a bit.
sf buf allocation, use wakeup() instead of wakeup_one() to notify sf
buffer waiters about free buffer.
sf_buf_alloc() calls msleep(PCATCH) when SFB_CATCH flag was given,
and for simultaneous wakeup and signal delivery, msleep() returns
EINTR/ERESTART despite the thread was selected for wakeup_one(). As
result, we loose a wakeup, and some other waiter will not be woken up.
Reported and tested by: az
Reviewed by: alc, jhb
MFC after: 1 week
1. Allow embedding the FDT into the kernel, just like PowerPC/book-E.
2. If the loader passes us a pointer to the bootinfo structure, save
it and use it to fill in the gaps (e.g. bus frequencies, etc).
DPCPU_DEFINE and VNET_DEFINE macros, as these cause problems for various
people working on the affected files. A better long-term solution is
still being considered. This reversal may give some modules empty
set_pcpu or set_vnet sections, but these are harmless.
Changes reverted:
------------------------------------------------------------------------
r215318 | dim | 2010-11-14 21:40:55 +0100 (Sun, 14 Nov 2010) | 4 lines
Instead of unconditionally emitting .globl's for the __start_set_xxx and
__stop_set_xxx symbols, only emit them when the set_vnet or set_pcpu
sections are actually defined.
------------------------------------------------------------------------
r215317 | dim | 2010-11-14 21:38:11 +0100 (Sun, 14 Nov 2010) | 3 lines
Apply the STATIC_VNET_DEFINE and STATIC_DPCPU_DEFINE macros throughout
the tree.
------------------------------------------------------------------------
r215316 | dim | 2010-11-14 21:23:02 +0100 (Sun, 14 Nov 2010) | 2 lines
Add macros to define static instances of VNET_DEFINE and DPCPU_DEFINE.
