- Update struct link_settings and associated shared code.
- Add tunables to control FEC and autonegotiation. All ports inherit
these values as their initial settings.
hw.cxgbe.fec
hw.cxgbe.autoneg
- Add per-port sysctls to control FEC and autonegotiation. These can be
modified at any time.
dev.<port>.<n>.fec
dev.<port>.<n>.autoneg
MFC after: 3 days
Sponsored by: Chelsio Communications
come up as 't6nex' nexus devices with 'cc' ports hanging off them.
The T6 firmware and configuration files will be added as soon as they
are released. For now the driver will try to work with whatever
firmware and configuration is on the card's flash.
Sponsored by: Chelsio Communications
The cxgbev/cxlv driver supports Virtual Function devices for Chelsio
T4 and T4 adapters. The VF devices share most of their code with the
existing PF4 driver (cxgbe/cxl) and as such the VF device driver
currently depends on the PF4 driver.
Similar to the cxgbe/cxl drivers, the VF driver includes a t4vf/t5vf
PCI device driver that attaches to the VF device. It then creates
child cxgbev/cxlv devices representing ports assigned to the VF.
By default, the PF driver assigns a single port to each VF.
t4vf_hw.c contains VF-specific routines from the shared code used to
fetch VF-specific parameters from the firmware.
t4_vf.c contains the VF-specific PCI device driver and includes its
own attach routine.
VF devices are required to use a different firmware request when
transmitting packets (which in turn requires a different CPL message
to encapsulate messages). This alternate firmware request does not
permit chaining multiple packets in a single message, so each packet
results in a firmware request. In addition, the different CPL message
requires more detailed information when enabling hardware checksums,
so parse_pkt() on VF devices must examine L2 and L3 headers for all
packets (not just TSO packets) for VF devices. Finally, L2 checksums
on non-UDP/non-TCP packets do not work reliably (the firmware trashes
the IPv4 fragment field), so IPv4 checksums for such packets are
calculated in software.
Most of the other changes in the non-VF-specific code are to expose
various variables and functions private to the PF driver so that they
can be used by the VF driver.
Note that a limited subset of cxgbetool functions are supported on VF
devices including register dumps, scheduler classes, and clearing of
statistics. In addition, TOE is not supported on VF devices, only for
the PF interfaces.
Reviewed by: np
MFC after: 2 months
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7599
routines available in t4_tom to manage the iSCSI DDP page pod region.
This adds the ability to use multiple DDP page sizes to the iSCSI
driver, among other improvements.
Sponsored by: Chelsio Communications
This permits a single early return for VF devices in the routines that
add sysctl nodes.
Reviewed by: np
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7512
- Add handling of VF register sets to t4_get_regs_len() and t4_get_regs().
- While here, use t4_get_regs_len() in the ioctl handler for regdump
instead of inlining it.
Reviewed by: np
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7484
Add fields to hold the SGE control register and free list buffer sizes to
the sge_params structure. Populate these new fields in
t4_init_sge_params() for PF devices and change t4_read_chip_settings() to
pull these values out of the params structure instead of reading
registers directly. This will permit t4_read_chip_settings() to be reused
for VF devices which cannot read SGE registers directly.
While here, move the call to t4_init_sge_params() to
get_params__post_init(). The VF driver will populate the SGE parameters
structure via a different method before calling t4_read_chip_settings().
Reviewed by: np
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7476
Chelsio T4/T5 adapters are multifunction cards. The main driver uses
physical function 4 (PF4). However, VF devices for SR-IOV are only
supported on physical functions 0 through 3, where PF0 creates VFs tied
to port 0, etc. The t4iov/t5iov driver was previously added to
create VF devices for ports that are present on each adapter. This
change uses the recently added pci_iov_attach_name() function to
name the character device in /dev/iov after the associated port on
the card (e.g. /dev/iov/cxl0 is used to create VFs that share the
cxl0 port). With this in place, mark the t4iov/t5iov devices quiet
to prevent them from cluttering dmesg.
Reviewed by: rstone
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7402
VF devices use a different register layout than PF devices. Storing
the offset in a value in the softc allows code to be shared between the
PF and VF drivers.
Reviewed by: np
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7389
- Remove null open/close methods.
- Don't set d_flags to 0 explicitly.
- Remove t5_cdevsw as the .d_name member isn't really used and doesn't
warrant a separate cdevsw just for the name.
- Use ENOTTY as the error value for an unknown ioctl request.
- Use make_dev_s() to close race with setting si_drv1.
Sponsored by: Chelsio Communications
AIO write requests for a TOE socket on a Chelsio T4+ adapter can now
DMA directly from the user-supplied buffer. This is implemented by
wiring the pages backing the user-supplied buffer and queueing special
mbufs backed by raw VM pages to the socket buffer. The TOE code
recognizes these special mbufs and builds a sglist from the VM page
array associated with the mbuf when queueing a work request to the TOE.
Because these mbufs do not have an associated virtual address, m_data
is not valid. Thus, the AIO handler does not invoke sosend() directly
for these mbufs but instead inlines portions of sosend_generic() and
tcp_usr_send().
An aiotx_buffer structure is used to describe the user buffer (e.g.
it holds the array of VM pages and a reference to the AIO job). The
special mbufs reference this structure via m_ext. Note that a single
job might be split across multiple mbufs (e.g. if it is larger than
the socket buffer size). The 'ext_arg2' member of each mbuf gives an
offset relative to the backing aiotx_buffer. The AIO job associated
with an aiotx_buffer structure is completed when the last reference to
the structure is released.
Zero-copy aio_write()'s for connections associated with a given
adapter can be enabled/disabled at runtime via the
'dev.t[45]nex.N.toe.tx_zcopy' sysctl.
MFC after: 1 month
Relnotes: yes
Sponsored by: Chelsio Communications
returning EAGAIN if they aren't available when the user tries to program
a filter. Do this after validating the filter so that the driver
doesn't bring up the queues if it doesn't have to.
Chelsio NICs are a bit unique compared to some other NICs in that they
expose different functionality on different physical functions. In
particular, PF4 is used to manage the NIC interfaces ('t4nex' and 't5nex').
However, PF4 is not able to create VF devices. Instead, VFs are only
supported by physical functions 0 through 3. This commit adds 't4iov'
and 't5iov' drivers that attach to PF0-3.
One extra wrinkle is that the iov devices cannot enable SR-IOV until the
firwmare has been initialized by the main PF4 driver. To handle this
case, a new t4_if kobj interface has been added to permit cross-calls
between the PF drivers. The PF4 driver notifies sibling drivers when it
is fully attached. It also requests sibling drivers to detach before it
detaches. Sibling drivers query the PF4 driver during their attach
routine to see if it is attached. If not, the sibling drivers defer
their attach actions until the PF4 driver informs them it is attached.
VF devices are associated with a single port on the NIC. VF devices
created from PF0 are associated with the first port on the NIC, VFs
from PF1 are associated with the second port, etc. VF devices can
only be created from a PF device that has an associated port. Thus,
on a 2-port card, VFs are only supported on PF0 and PF1.
Reviewed by: np (earlier versions)
MFC after: 1 month
Sponsored by: Chelsio Communications
related to "shared" CPLs.
a) Combine t4_set_tcb_field and t4_set_tcb_field_rpl into a single
function. Allow callers to direct the response to any iq. Tidy up
set_ulp_mode_iscsi while there to use names from t4_tcb.h instead of
magic constants.
b) Remove all CPL handler tables from struct adapter. This reduces its
size by around 2KB. All handlers are now registered at MOD_LOAD instead
of attach or some kind of initialization/activation. The registration
functions do not need an adapter parameter any more.
c) Add per-iq handlers to deal with CPLs whose destination cannot be
determined solely from the opcode. There are 2 such CPLs in use right
now: SET_TCB_RPL and L2T_WRITE_RPL. The base driver continues to send
filter and L2T_WRITEs over the mgmtq and solicits the reply on fwq.
t4_tom (including the DDP code) now uses the port's ctrlq to send
L2T_WRITEs and SET_TCB_FIELDs and solicits the reply on an ofld_rxq.
fwq and ofld_rxq have different handlers that know what kind of tid to
expect in the reply. Update t4_write_l2e and callers to to support any
wrq/iq combination.
Approved by: re@ (kib@)
Sponsored by: Chelsio Communications
The interface's queues are functional after VI_INIT_DONE (which is short
of interface-up) and that's all that's needed for t4_tom to communicate
with the chip.
Approved by: re@ (gjb@)
Sponsored by: Chelsio Communications
vcxgbe/vcxl interfaces and retire the 'n' interfaces. The main
cxgbe/cxl interfaces and tunables related to them are not affected by
any of this and will continue to operate as usual.
The driver used to create an additional 'n' interface for every
cxgbe/cxl interface if "device netmap" was in the kernel. The 'n'
interface shared the wire with the main interface but was otherwise
autonomous (with its own MAC address, etc.). It did not have normal
tx/rx but had a specialized netmap-only data path. r291665 added
another set of virtual interfaces (the 'v' interfaces) to the driver.
These had normal tx/rx but no netmap support.
This revision consolidates the features of both the interfaces into the
'v' interface which now has a normal data path, TOE support, and native
netmap support. The 'v' interfaces need to be created explicitly with
the hw.cxgbe.num_vis tunable. This means "device netmap" will not
result in the automatic creation of any virtual interfaces.
The following tunables can be used to override the default number of
queues allocated for each 'v' interface. nofld* = 0 will disable TOE on
the virtual interface and nnm* = 0 to will disable native netmap
support.
# number of normal NIC queues
hw.cxgbe.ntxq_vi
hw.cxgbe.nrxq_vi
# number of TOE queues
hw.cxgbe.nofldtxq_vi
hw.cxgbe.nofldrxq_vi
# number of netmap queues
hw.cxgbe.nnmtxq_vi
hw.cxgbe.nnmrxq_vi
hw.cxgbe.nnm{t,r}xq{10,1}g tunables have been removed.
--- tl;dr version ---
The workflow for netmap on cxgbe starting with FreeBSD 11 is:
1) "device netmap" in the kernel config.
2) "hw.cxgbe.num_vis=2" in loader.conf. num_vis > 2 is ok too, you'll
end up with multiple autonomous netmap-capable interfaces for every
port.
3) "dmesg | grep vcxl | grep netmap" to verify that the interface has
netmap queues.
4) Use any of the 'v' interfaces for netmap. pkt-gen -i vcxl<n>... .
One major improvement is that the netmap interface has a normal data
path as expected.
5) Just ignore the cxl interfaces if you want to use netmap only. No
need to bring them up. The vcxl interfaces are completely independent
and everything should just work.
---------------------
Approved by: re@ (gjb@)
Relnotes: Yes
Sponsored by: Chelsio Communications
- Validate the scheduling class against the actual limit (which is chip
specific) instead of a magic number.
- Return an error if an attempt is made to manipulate the tx queues of a
VI that hasn't been initialized.
Sponsored by: Chelsio Communications
Chelsio's TCP offload engine supports direct DMA of received TCP payload
into wired user buffers. This feature is known as Direct-Data Placement.
However, to scale well the adapter needs to prepare buffers for DDP
before data arrives. aio_read() is more amenable to this requirement than
read() as applications often call read() only after data is available in
the socket buffer.
When DDP is enabled, TOE sockets use the recently added pru_aio_queue
protocol hook to claim aio_read(2) requests instead of letting them use
the default AIO socket logic. The DDP feature supports scheduling DMA
to two buffers at a time so that the second buffer is ready for use
after the first buffer is filled. The aio/DDP code optimizes the case
of an application ping-ponging between two buffers (similar to the
zero-copy bpf(4) code) by keeping the two most recently used AIO buffers
wired. If a buffer is reused, the aio/DDP code is able to reuse the
vm_page_t array as well as page pod mappings (a kind of MMU mapping the
Chelsio NIC uses to describe user buffers). The generation of the
vmspace of the calling process is used in conjunction with the user
buffer's address and length to determine if a user buffer matches a
previously used buffer. If an application queues a buffer for AIO that
does not match a previously used buffer then the least recently used
buffer is unwired before the new buffer is wired. This ensures that no
more than two user buffers per socket are ever wired.
Note that this feature is best suited to applications sending a steady
stream of data vs short bursts of traffic.
Discussed with: np
Relnotes: yes
Sponsored by: Chelsio Communications
Figure out if the chip is counting PAUSE frames in the "normal" stats
and take them out if it is. This fixes a bug in the tx stats because
the default hardware behavior is different for Tx and Rx but the driver
was treating both the same way. The result was that OPACKETS, OBYTES,
and OMCASTS were under-reported (if tx_pause > 0) before this change.
Note that the mac_stats sysctl still gives you the raw value of these
statistics straight from the device registers.
