handlers, some of which had to do awkward things to get a large enough
FIXEDLEN buffer.
Note that some sysctl handlers were explicitly outputting a trailing NUL
byte. This behaviour was preserved, though it should not be necessary.
Reviewed by: phk
PCI status register to map its current name.
- Use PCIM_* rather than PCIR_* for constants for fields in various AER
registers. I got about half of them right in the previous commit.
MFC after: 1 week
K2 SATA controllers. The chip's status register must be read first, and
as a long, for other registers to be correctly updated after a command, and
this includes the command sequence in device detection as well as the
previously handled case after interrupts. While here, clean up some
previous hacks related to this controller.
Reported by: many
Reviewed by: mav
MFC after: 3 weeks
PCI-express. I used PCIZ_* for ID constants (plain capability IDs use
PCIY_*).
- Add register definitions for the Advanced Error Reporting, Virtual
Channels, and Device Serial Number extended capabilities.
- Teach pciconf -c to list extended as well as plain capabilities. Adds
more detailed parsing for AER, VC, and device serial numbers.
MFC after: 2 weeks
are still bound to BSP. It confuses timer management logic in per-CPU mode
and may cause timer not being reloaded. Check such cases on interrupt
arival and reload timer to give system some more time to manage proper
binding.
discrepencies from the igb version which was the target.
Change the message when neither MSI or MSIX are enabled
and a fallback to Legacy interrupts happen, the existing
message was confusing.
- add identify method to create driver's own device_t
- successfully probe only driver's own device_t instead of any device_t
- (ab)use device order to hopefully be probed/attached after acpi_wmi
PR: kern/147858
Tested by: Maciej Suszko <maciej@suszko.eu>
MFC after: 1 week
- Add special check for case when time expires before being programmed.
This fixes interrupt loss and respectively timer death on attempt to
program very short interval. Increase minimal supported period to more
realistic value.
- Add support for hint.hpet.X.allowed_irqs tunable, allowing manually
specify which interrupts driver allowed to use. Unluckily, many BIOSes
program wrong allowed interrupts mask, so driver tries to stay on safe
side by not using unshareable ISA IRQs. This option gives control over
this limitation, allowing more per-CPU timers to be provided, when FSB
interrupts are not supported. Value of this tunable is bitmask.
- Do not use regular interrupts on virtual machines. QEMU and VirtualBox
do not support them properly, that may cause problems. Stay safe by default.
Same time both QEMU and VirtualBox work fine in legacy_route mode.
VirtualBox also works fine if manually specify allowed ISA IRQs with above.
Both deadline and current_time are time_seconds (+ utc_offset())
casted to unsigned long long. No need to cast to or print as pointers.
MFC after: 4 days
to pad with 0xFF when it encounter short frames. According to RFC
1042 the pad bytes should be 0x00.
Because manual padding consumes extra CPU cycles, introduce a new
tunable which controls the padding behavior. Turning this tunable
on will have driver pad manually but it's disabled by default. Users
can enable software padding by setting the following tunable to
non-zero value.
dev.sis.%d.manual_pad="1"
PR: kern/35422 (patch not used)
prevented driver from working on big-endian machines. Also rewrite
station address programming to make it work on strict-alignment
architectures. With this change, sis(4) now works on sparc64 and
performance number looks good even though sis(4) have to apply
fixup code to align received frames on 2 bytes boundary on sparc64.
response to DMA activate FIS under certain circumstances. This is
recommended fix from chip datasheet. If triggered, this bug most likely
cause write command timeout.
MFC after: 2 weeks
value 0xff. On hot-plug this value confuses ata_generic_reset() device
presence detection logic. As soon as we already know drive presence from
SATA hard reset, hint ata_generic_reset() to wait for device signature
until success or full timeout.
greater than 65535 bytes then the CDC driver might not work as expected, which
is not likely with the existing USB speeds.
Submitted by: Hans Petter Selasky
allmulti is toggled. Controller does not require reinitialization.
This removes unnecessary controller reinitialization whenever
tcpdump is used.
While I'm here remove unnecessary variable reinitialization.
configured TX/RX MACs before getting a valid link. After that, when
link state change callback is called, it called device
initialization again to reconfigure TX/RX MACs depending on
resolved link state. This hack created several bad side effects and
it required more hacks to not collide with sis_tick callback as
well as disabling switching to currently selected media in device
initialization. Also it seems sis(4) was used to be a template
driver for long time so other drivers which was modeled after
sis(4) also should be changed.
TX/RX MACs are now reconfigured after getting a valid link. Fix for
short cable error is also applied after getting a link because it's
only valid when the resolved speed is 100Mbps.
While I'm here slightly reorganize interrupt handler such that
sis(4) always read SIS_ISR register to see whether the interrupt is
ours or not. This change removes another hack and make it possible
to nuke sis_stopped variable in softc.
o Enforce TX/RX descriptor ring alignment. NS data sheet says the
controller needs 4 bytes alignment but use 16 to cover both SiS
and NS controllers. I don't have SiS data sheet so I'm not sure
what is alignment restriction of SiS controller but 16 would be
enough because it's larger than the size of a TX/RX descriptor.
Previously sis(4) ignored the alignment restriction.
o Enforce RX buffer alignment, 4.
Previously sis(4) ignored RX buffer alignment restriction.
o Limit number of TX DMA segment to be used to 16. It seems
controller has no restriction on number of DMA segments but
using more than 16 looks resource waste.
o Collapse long mbuf chains with m_collapse(9) instead of calling
expensive m_defrag(9).
o TX/RX side bus_dmamap_load_mbuf_sg(9) support and remove
unnecessary callbacks.
o Initial endianness support.
o Prefer local alignment fixup code to m_devget(9).
o Pre-allocate TX/RX mbuf DMA maps instead of creating/destroying
these maps in fast TX/RX path. On non-x86 architectures, this is
very expensive operation and there is no need to do that.
o Add missing bus_dmamap_sync(9) in TX/RX path.
o watchdog is now unarmed only when there are no pending frames
on controller. Previously sis(4) blindly unarmed watchdog
without checking the number of queued frames.
o For efficiency, loaded DMA map is reused for error frames.
o DMA map loading failure is now gracefully handled. Previously
sis(4) ignored any DMA map loading errors.
o Nuke unused macros which are not appropriate for endianness
operation.
o Stop embedding driver maintained structures into descriptor
rings. Because TX/RX descriptor structures are shared between
host and controller, frequent bus_dmamap_sync(9) operations are
required in fast path. Embedding driver structures will increase
the size of DMA map which in turn will slow down performance.
