firmware versions which wedge when using the OFW test service,
so given that we don't really depend on SUNW,stop-self just nuke
it altogether instead of risking problems.
- At least Fire V880 have a small hardware glitch which causes the
reception of IDR_NACKs for CPUs we actually haven't tried to send
an IPI to, even not as part of the initial try. According to tests
this apparently can be safely ignored though, so just return if
checking for the individual IDR_NACKs indicates no outstanding
dispatch. Serializing the sending of IPIs between MD and MI code
by the combined usage of smp_ipi_mtx makes no difference to this
phenomenon. [1]
- Provide relevant debugging bits already with the initial panic
in case of problems with the IPI dispatch, which would have
allowed to diagnose the above problem without a specially built
kernel.
- In case of cheetah_ipi_selected() base the delay we wait for
other CPUs which also might want to dispatch IPIs on the total
amount of CPUs instead of just the number of CPUs we let this
CPU send IPIs to because in the worst case all CPUs also want
to IPI us at the same time.
Reported and access for extensive tests provided by: Beat Gaetzi [1]
destroy operation until the referenced clone device has
been closed by the process properly. The behavior is now
consistently with the previous release.
Reviewed by: Kip Macy
event from mii(4) may not be delivered if valid link was already
established. To address the issue, check current link state after
driving MII_TICK. This should fix a regression introduced in
r184245.
PR: kern/129647
event from mii(4) may not be delivered if valid link was already
established. To address the issue, check current link state after
driving MII_TICK. This should fix a regression introduced in
r185753 on fast ethernet controllers.
Reported by: csjp, Bruce Cran < bruce <> cran DOT org DOT uk >
Tested by: csjp, Bruce Cran (initial version)
In r185891 I removed the newlines from messages written to /dev/console,
because it made startup messages from rc-scripts harder to read. This,
unfortunately, causes the kernel message that is printed after a
non-terminated log message to be concatenated.
This could be fixed, but on short term it's better to just revert the
change.
Reported by: Jaakko Heinonen <jh saunalahti fi>
Inside ptsdrv_{in,out}wakeup() we call KNOTE_LOCKED() to wake up any
kevent(2) users. Because the kqueue handlers are executed synchronously,
we must set PTS_FINISHED before calling ptsdrv_{in,out}wakeup().
Discovered by: nork
Right now the wchan strings "ttyinp" and "ttybgw" only differ one
character from the strings we used prior to MPSAFE TTY. Just rename them
back to their pre-MPSAFE TTY counterparts.
Also rename "ttylck" to "ttymtx", which should make it more clear that a
process is blocked on the TTY mutex, not some other form of locking.
o add support for IXP435 cpu's (e.g. 64 irq's)
o add support for Cambria-specific devices: npe, led's (front panel and
octal latch), ehci, mcu, ide cf
o redo memory mapping for xscale/ixp4xx boards: previously memory
was assumed aliased to 0x10000000 but this appears to be true only
for ixp425 systems and breaks operation on others; rework so memory
is assumed to start at 0
o rework NPE configuration support to use NPE id's instead of port #'s;
these changes also rename the associated MAC's to follow the NPE's
they are attached to
o update npe firmware to latest rev (same license) and update default fw
imageid's to match; in particular this adds NPE-A and crypto support
o re-style NPE fw handling code and add a console msg identifying the
attributes of the loaded fw
o fix numerous problems with handling failures during npe setup
o fix npe rx q setup; need to spin waiting for mailbox responses during
early boot stages as qmgr interrupts are not delivered; this fixes
the problem where all 8 traffic classifications were not tied to the
rx q (and eliminates the console msg "remember to fix rx q setup")
o add DELAY to npe MII wait logic for IXP435
o strip down builtin phys->virt address translation table in resource
handling to just those resources that require it and add a console msg
to alert people when this (kludge) table needs to be extended
o purge a bunch of dead netbsd-ism's
o cleanup avila led driver
o add Cambria support to boot2 and rework code for better multi-board support
Notes:
1. NPE-A doesn't work and causes NPE-C to stop working; it is disabled
in the hints
2. USB isn't working yet; controller communicates ok but device
discovery fails
3. Cambria support must be configured separately from IXP425 boards;
multi-board support is TBD
Sponsored by: Hobnob, Gateworks (board donation)
Reviewed by: imp
o add support to byte swap EHCI descriptor contents; the IXP435
has dual-EHCI controllers integral but descriptor contents are
in big-endian format; this support is configured with the
USB_EHCI_BIG_ENDIAN_DESC option and enabled with EHCI_SCFLG_BIGEDESC
o clean up EHCI USBMODE register setup during init; add #defines for
bit values
o split debug support out into a new file and enable use through ddb
o while here remove a bunch of lingering netbsd-isms
Reviewed by: imp
of OFW access semantics, in order to allow future support for real-mode
OF access and flattened device frees. OF client interface modules are
implemented using KOBJ, in a similar way to the PPC PMAP modules.
Because we need Open Firmware to be available before mutexes can be used on
sparc64, changes are also included to allow KOBJ to be used very early in
the boot process by only using the mutex once we know it has been initialized.
Reviewed by: marius, grehan
This commit is slightly different from the original patch in the PR:
1. EM_ALPHA keeps the old value for compatibility reason.
2. Non-standard SHT_NUM is not added.
3. Style.
PR: kern/118540
Submitted by: "Pedro F. Giffuni" <giffunip[at]tutopia.com>
Intel 855 chips present the same pci id for both heads. This prevents
us from attaching to the dummy second head. All other chips that I
am aware of either only present a single pci id, or different ids
for each head so that we only match on the correct head.
Approved by: kib@
MFC after: 2 weeks
storage class. This check was lost. It is not important for the most cases,
but as it was reported on current@, it does important for sis driver and
surely inportant for AHCI driver. So restore it there.
Submitted by: Toshikazu ICHINOSEKI, Andrey V. Elsukov
Discussed on: current@
ati pci gart to use bus_dma to handle the allocations. This fixes
a garbled screen issue on at least some radeons (X1400 tested). It is
also likely that this is the correct fix for PR# 119324, though that
is not confirmed yet.
Reviewed by: jhb@ (mentor, prior version)
Approved by: kib@
MFC after: 2 weeks
be fatal so just inform about this instead of panicing.
- Ensure we use the right softc in case the interrupt of a child is
is routed to the companion PBM instead. This hasn't been seen in the
wild so far but given that it's the case for the Schizo interrupts,
handling this situation also for child interrupts as a precaution
seemed a good idea.
- Deal with broken firmware versions which miss child entries in the
ino-bitmap as seen on V880 by belatedly registering as interrupt
controller in schizo_setup_intr(). [1]
- Add missing '\n' when printing the warning regarding Schizo Errata
I-13.
Reported and tested by: Beat Gaetzi [1]
- Make LBC resources management self-contained: introduce explicit LBC
resources definition (much like the OCP), provide dedicated rman for LB mem
space.
- Full configuration of an LB chip select device: program LAW and BR/OR, map
into KVA, handle all LB attributes (bus width, machine select, ecc,
write protect etc).
- Factor out LAW manipulation routines into shared code, adjust OCP area
accordingly.
- Other LBC fixes and clean-ups.
Obtained from: Semihalf
NULL pointer to struct mount if the looked up vnode is reclaimed. Also,
these syscalls only mnt_ref() the mp, still allowing it to be unmounted;
only struct mount memory is kept from being reused.
Lock the vnode when doing name lookup, then reference its mount point,
unlock the vnode and vfs_busy the mountpoint. This sequence shall take
care of both races.
Reported and tested by: pho
Discussed with: attilio
MFC after: 1 month
payload length in TSO case. Leaving unused TBD also seem to cause
SCB timeouts under certain conditions when TSO/non-TSO traffics
are active at the same time.
Add code to the Chelsio driver so that it can recognize different
module types which may be plugged into it, including SR, LR lasers
and TWINAX copper cables.
Obtained from: Chelsio Inc.
MFC after: 1 week
it running under a virtual environment. This also introduces a globally
accessible variable vm_guest that can be used where appropriate in the
kernel to inspect this environment.
To make it easier for the long run, an enum VM_GUEST is also introduced,
which could possibly be factored out in a header somewhere (but the
question is where - vm/vm_param.h? sys/param.h?) so it eventually becomes
a part of the standard KPI. In any case, it's a start.
The purpose of all this isn't to absolutely detect that the OS is running
under a virtual environment (cf. "redpill") but to allow the parts of the
kernel and the userland that care about this particular aspect and can do
something useful depending on it to have a standardised interface. Reducing
kern.hz is one example but there are other things that could be done like
avoiding context switches, not using CPU instructions that are known to be
slow in emulation, possibly different strategies in VM (memory) allocation,
CPU scheduling, etc.
It isn't clear if the JAILS/VIMAGE functionality should also be exposed
by this particular mechanism (probably not since they're not "full"
virtual hardware environments). Sometime in the future another sysctl and
a variable could be introduced to reflect if the kernel supports any kind
of virtual hosting (e.g. VMWare VMI, Xen dom0).
Reviewed by: silence from src-commiters@, virtualization@, kmacy@
Approved by: gnn (mentor)
Security: Obscurity doesn't help.
- split bootstrap code into more modular routines, which will also be used for
the non-booting cores
- clean up registers usage
- improve comments to better reflect reality
- eliminate dead or redundant code
- other minor fixes
This refactoring is a preliminary step before importing dual-core (MPC8572)
support.
Obtained from: Freescale, Semihalf
had been the only flag with random usage patterns.
Switch inc_flags to be used as a real bit field by using
INC_ISIPV6 with bitops to check for the 'isipv6' condition.
While here fix a place or two where in case of v4 inc_flags
were not properly initialized before.[1]
Found by: rwatson during review [1]
Discussed with: rwatson
Reviewed by: rwatson
MFC after: 4 weeks
command whenever Tx completion interrupt is raised. The Tx poll
bit is cleared when all packets waiting to be transferred have been
processed. This means the second Tx poll command can be silently
ignored as the Tx poll bit could be still active while processing
of previous Tx poll command is in progress.
To address the issue re(4) used to invoke the Tx poll command in Tx
completion handler whenever it detects there are pending packets in
TxQ. However that still does not seem to completely eliminate
watchdog timeouts seen on RealTek PCIe controllers. To fix the
issue kick Tx poll command only after Tx completion interrupt is
raised as this would indicate Tx is now idle state such that it can
accept new Tx poll command again. While here apply this workaround
for PCIe based controllers as other controllers does not seem to
have this limitation.
Tested by: Victor Balada Diaz < victor <> bsdes DOT net >
out of sleep mode prior to accessing to PHY. This should fix device
attach failure seen on these controllers. Also enable the sleep
mode when device is put into sleep state.
PR: kern/123123, kern/123053
* Remove trailing whitespace (added in r186162)
* Reduce indentation by rephrasing test
Submitted by: Christopher Mallon (christoph dot mallon at gmx dot de)
- threadA runs vfs_rel(mp1)
- threadB does unmount the mp1 fs, sets MNTK_UNMOUNT and drop MNT_ILOCK()
- threadA runs vfs_busy(mp1) and, as long as, MNTK_UNMOUNT is set, sleeps
waiting for threadB to complete the unmount
- threadB, in vfs_mount_destroy(), finds mnt_lock > 0 and sleeps waiting
for the refcount to expire.
Fix the deadlock by adding a flag called MNTK_REFEXPIRE which signals the
unmounter is waiting for mnt_ref to expire.
The vfs_busy contenders got awake, fails, and if they retry the
MNTK_REFEXPIRE won't allow them to sleep again.
2) Simplify significantly the code of vfs_mount_destroy() trimming
unnecessary codes:
- as long as any reference exited, it is no-more possible to have
write-op (primarty and secondary) in progress.
- it is no needed to drop and reacquire the mount lock.
- filling the structures with dummy values is unuseful as long as
it is going to be freed.
Tested by: pho, Andrea Barberio <insomniac at slackware dot it>
Discussed with: kib
anything other than 0. Make it so. This fixes
"panic: VOP_STRATEGY failed bp=0xc320dd90 vp=0xc3b9f648",
encountered when writing to an orphaned filesystem. Reason
for the panic was the following assert:
KASSERT(i == 0, ("VOP_STRATEGY failed bp=%p vp=%p", bp, bp->b_vp));
at vfs_bio:bufstrategy().
Reviewed by: scottl, phk
Approved by: rwatson (mentor)
Sponsored by: FreeBSD Foundation
result in panic:
mdconfig -af blah.img -o force
mount /dev/md0 /mnt
mdconfig -du 0
Reviewed by: scottl
Approved by: rwatson (mentor)
Sponsored by: FreeBSD Foundation
o Add support for compiling elf64 for this file (the rest of the changes are
coming later)
o Fill in some misssing relocation types. We need to support these in
elf_machdep.c's relocation routines eventually, but that's future work
too.
the device, which means refcount on periph drivers never drops,
which means cam_sim_free() never returns, which results in umass
sleeping there ad infinitum.
Submitted by: pjd
Reviewed by: scottl, pjd
Approved by: rwatson (mentor)
Sponsored by: FreeBSD Foundation
unregistration, and execution:
- Add some brackets for clarity and trim a bit of vertical whitespace.
- Remove comments that may not contribute to clarity, such as "Lock"
before acquiring a lock and "Get memory" before allocating memory.
- During hook registration, don't drop pfil_list_lock between checking
for a duplicate and registering the hook, as this leaves a race
condition by failing to enforce the "no duplicate hooks" invariant.
- Don't lock the hook during registration, since it's not yet in use.
- Document assumption that hooks will be quiesced before being
unregistered.
- Don't write-lock hooks during removal because they are assumed
quiesced.
- Rename "done" label to "locked_error" to be clear that it's an error
path on the way out of hook execution.
MFC after: pretty soon
does - in DragonFly, it's cam_sim_release() what actually frees the
SIM; cam_sim_free does nothing more than calling cam_sim_release().
Here, we drain in cam_sim_free, waiting for refcount to drop to zero.
We cannot do the same think DragonFly does, because after cam_sim_free
returns, client would destroy the sim->mtx, and CAM would trip over
an initialized mutex.
Reviewed by: scottl
Approved by: rwatson (mentor)
Sponsored by: FreeBSD Foundation
to actually use it would panic on mtx operation, as dead_sim doesn't
have a proper mutex. Even if it had a properly initialized mutex,
it wouldn't have properly locked and owned one.
Reviewed by: scottl
Approved by: rwatson (mentor)
Sponsored by: FreeBSD Foundation
