numbers and handle types in rational way. This will better protect from
(unwittingly) dealing with stale handles/commands.
Fix the watchdog timeout code to better protect itself from mistakes.
If we run an abort on a putatively timed out command, the command
may in fact get completed, so check to make sure the command we're
timing it out is still around. If the abort succeeds, btw, the command
should get returned via a different path.
TNT5004 IC. This involved a major rewrite of a number of things, as
this chip no longer supports the NAT7210 legacy mode but requires the
host to use the (more modern) FIFO mode.
In theory, this also ought to work on the older TNT4882C chip. I'll
probably add this as optional support (perhaps by a device.hints flag)
later on. By now, FIFO mode is *only* activates iff a TNT5004 chip
has been detected (where the old code didn't work at all), while
everything else is supposed to use the old code.
MFC after: 2 weeks
no effect. Make sure to clear error bits by writing 1. [1]
While I'm here use predefined value instead of hardcodig magic
vlaue.
Submitted by: msaitoh at NetBSD [1]
lagg and vlan the vlan attach/detach event is not being
handed down to em, this caused some init code not to run,
and thus VLANs did not work. Ultimately having the event
get propagated would be nice, but for now the solution is
to have HWFILTER off by default, when this is the case
VLANs will work, ifconfig can be used to turn it on and
then get HW tag filtering.
available today.
This card is a low power 802.11bgn that only does 11n rates up to MCS 7
(that's 65 Mbps in 20Mhz mode and 135 in 40Mhz mode).
802.11n is not yet supported, but will be in the future.
The driver still has a problem regarding to the setting of txpower on
the card, so don't expect good performance yet. After fixing this
problem, an MFC is possible.
Special thanks to iXsystems and S Smirnov <tonve at yandex.ru> for help
with the purchase of a netbook with this card.
Sponsored by: iXsystems, Inc.
- Unify bus reset/probe sequence. Whenever bus attached at boot or later,
CAM will automatically reset and scan it. It allows to remove duplicate
code from many drivers.
- Any bus, attached before CAM completed it's boot-time initialization,
will equally join to the process, delaying boot if needed.
- New kern.cam.boot_delay loader tunable should help controllers that
are still unable to register their buses in time (such as slow USB/
PCCard/ CardBus devices), by adding one more event to wait on boot.
- To allow synchronization between different CAM levels, concept of
requests priorities was extended. Priorities now split between several
"run levels". Device can be freezed at specified level, allowing higher
priority requests to pass. For example, no payload requests allowed,
until PMP driver enable port. ATA XPT negotiate transfer parameters,
periph driver configure caching and so on.
- Frozen requests are no more counted by request allocation scheduler.
It fixes deadlocks, when frozen low priority payload requests occupying
slots, required by higher levels to manage theit execution.
- Two last changes were holding proper ATA reinitialization and error
recovery implementation. Now it is done: SATA controllers and Port
Multipliers now implement automatic hot-plug and should correctly
recover from timeouts and bus resets.
- Improve SCSI error recovery for devices on buses without automatic sense
reporting, such as ATAPI or USB. For example, it allows CAM to wait, while
CD drive loads disk, instead of immediately return error status.
- Decapitalize diagnostic messages and make them more readable and sensible.
- Teach PMP driver to limit maximum speed on fan-out ports.
- Make boot wait for PMP scan completes, and make rescan more reliable.
- Fix pass driver, to return CCB to user level in case of error.
- Increase number of retries in cd driver, as device may return several UAs.
