was introduced. If you have a bus, say cardbus, that is derived from
a base-bus (say PCI), then ordinarily all PCI drivers would attach to
cardbus devices. However, there had been one exception: kldload
wouldn't work.
The problem is in devclass_add_driver. In this routine, all we did
was call to the pci device's BUS_DRIVER_ADDED routine. However, since
cardbus bus instances had a different devclass, none of them were
called.
The solution is to call all subclass devclasses, recursively down the
tree, of the class that was loaded. Since we don't have a 'children
class' pointer, we search the whole list of devclasses for a class
whose parent matches. Since just done a kldload time, this isn't as
bad as it sounds. In addition, we short-circuit the whole process by
marking those classes with subclasses with a flag. We'll likely have
to reevaluate this method the number of devclasses with subclasses
gets large.
This means we can remove the "cardbus" lines from all the PCI drivers
since we have no cardbus specific attach device attachments in the
tree.
# Also: minor tweak to an error message
unlikely but not impossible given modern thread counts) wrap-around,
and the compiler was padding it out to an int (at least) anyway.
MFC after: 3 days (but confirm ABI impact)
system call entry path and i386 IP checksum generation: we now assume
all code is MPSAFE unless explicitly marked otherwise. Remove XXX
Giant comments along similar lines: the code by the comments either
doesn't need or doesn't want Giant (especially the NMI handler).
MFC after: 3 days
not there is an audit record hung off of td_ar on the current thread.
Test this flag instead of td_ar when auditing syscall arguments or
checking for an audit record to commit on syscall return. Under
these circumstances, td_pflags is much more likely to be in the cache
(especially if there is no auditing of the current system call), so
this should help reduce cache misses in the system call return path.
MFC after: 1 week
Reported by: kris
Obtained from: TrustedBSD Project
get default next page configuration. While I'm here explicitly set
IP1000PHY_ANAR_CSMA bit. This bit is read-only and always set
by hardware so setting it has no effect but it would clear the
intention. With this change controllers that couldn't establish
1000baseT link should work.
PR: kern/130846
mapping. The tunable is OFF for all controllers except RTL8169SC
family. RTL8169SC seems to require more magic to use memory
register mapping. r187483 added a fix for RTL8169SCe controller but
it does not looke like fix other variants of RTL8169SC.
Tested by: Gavin Stone-Tolcher g.stone-tolcher <> its dot uq dot edu dot au
o correct dBm<->mW conversion logic
o set net80211 TXPMGT capability only if driver reports it is capable
PR: kern/132342
Submitted by: "Paul B. Mahol" <onemda@gmail.com>
Fix bugs and improve HID parsing.
- fix possible memory leak found
- fix possible NULL pointer access
- fix possible invalid memory read
- parsing improvements
- reset item data position when a new report ID is detected.
Submitted by: Hans Petter Selasky
query functions in the kernel, as these effectively serialize
parallel calls to the gettimeofday(2) system call, as well as
other kernel services that use timestamps.
Use the NetBSD version of the fix (kern_tc.c:1.32 by ad@) as
they have picked up our timecounter code and also ran into the
same problem.
Reported by: kris
Obtained from: NetBSD
MFC after: 3 days
locks: a global list/counter/generation counter protected by a new
mutex unp_list_lock, and a global linkage rwlock, unp_global_rwlock,
which protects the connections between UNIX domain sockets.
This eliminates conditional lock acquisition that was previously a
property of the global lock being held over sonewconn() leading to a
call to uipc_attach(), which also required the global lock, but
couldn't rely on it as other paths existed to uipc_attach() that
didn't hold it: now uipc_attach() uses only the list lock, which
follows the linkage lock in the lock order. It may also reduce
contention on the global lock for some workloads.
Add global UNIX domain socket locks to hard-coded witness lock
order.
MFC after: 1 week
Discussed with: kris
A difference between the old and the new TTY layer is that the new
implementation does not perform any post-processing before returning
data back to userspace when calling read().
sh(1)'s read turns the TTY into a raw mode before calling select(). This
means that the first character will not receive any ICRNL processing.
Inherit this flag from the original terminal attributes.
Even though this issue is not present on RELENG_*, I'm MFCing it to make
sh(1) in jails behave better.
PR: bin/129566
MFC after: 2 weeks
directory of a vnode to find a dirent with a matching file number. The
name from that dirent is then used to provide the component name.
Note: if the initial vnode argument is not a directory itself, then
the default VOP_VPTOCNP(9) implementation still returns ENOENT.
Reviewed by: kib
Approved by: kib
Tested by: pho
extended attribute get/set; in the case of get an uninitialized user
buffer was passed before the EA was retrieved, making it of relatively
little use; the latter was simply unused by any policies.
Obtained from: TrustedBSD Project
Sponsored by: Google, Inc.
naming by renaming certain "proc" entry points to "cred" entry points,
reflecting their manipulation of credentials. For some entry points,
the process was passed into the framework but not into policies; in
these cases, stop passing in the process since we don't need it.
mac_proc_check_setaudit -> mac_cred_check_setaudit
mac_proc_check_setaudit_addr -> mac_cred_check_setaudit_addr
mac_proc_check_setauid -> mac_cred_check_setauid
mac_proc_check_setegid -> mac_cred_check_setegid
mac_proc_check_seteuid -> mac_cred_check_seteuid
mac_proc_check_setgid -> mac_cred_check_setgid
mac_proc_check_setgroups -> mac_cred_ceck_setgroups
mac_proc_check_setregid -> mac_cred_check_setregid
mac_proc_check_setresgid -> mac_cred_check_setresgid
mac_proc_check_setresuid -> mac_cred_check_setresuid
mac_proc_check_setreuid -> mac_cred_check_setreuid
mac_proc_check_setuid -> mac_cred_check_setuid
Obtained from: TrustedBSD Project
Sponsored by: Google, Inc.
Translate getdate.y into C for portability. Make the get_date()
function easier to test as well:
* Have it accept a time_t "now" to use as a reference so that test
code can verify relative time specifications against known starting
points.
* Set up default date after parsing the string so that we
can use the specified timezone (if any) instead of the local
default. Otherwise, local DST makes it almost impossible to
reliably test time specifications such as "sunday UTC"
