Remove a lot of older cruft not needed.
Improve ISR support, but it is still unused since polling is faster
Properly initalize the speed register to get 90kb/s, not 400b/s.
Try to catch NACK
Allow 0 length read transfers to generate start/top pairs.
o Don't delay when checking the done bits. There's no gain other
than a small performance hit.
o calculate the clock divisors better (things are still way slow,
so maybe there's more here?)
o don't always fail reset. Always succeed instead.
o fix inverted logic around at91_twi_wait() return value
o remove debug code
o remove unneeded, unworking junk
o ixp425 support
o NPE network driver (requires Intel microcode)
o h/w qmgr support
o True IDE compact flash over expansion bus
o pci (ath and hifn795x parts tested)
o xscale watchdog timer
o ds1672 RTC on i2c bus
o ad7418 voltage + temp monitoring on i2c bus
o uart
Work done together with cognet, kevlo, and jmg. Parts of
the ixp425 support obtaine/derived from netbsd.
Reviewed by: cognet, imp
MFC after: 1 month
o Fix the packet statistics
o Make sure we set the FD bit when in full duplex
o Improve TX side efficency by eliminating a data copy for
unfragmented mbufs (the hardware can't do s/g).
o Minor busdma pedantry
o better comments in some places, more XXX in others
o Minor style nits.
This solves a problem I was seeing where I'd get no ethernet when not
booting with a NFS root. Well, unless I unplugged the cable and
plugged it back in first so I'd get the same up down up messages I get
for NFS root...
Thanks to sam and scottl for suggestions on making this driver more
efficient through better use of approrpiate APIs.
a lock to prevent interspersed strings written from different CPUs
at the same time.
To avoid putting a buffer on the stack or having to malloc one,
space is incorporated in the per-cpu structure. The buffer
size if 128 bytes; chosen because it's the next power of 2 size
up from 80 characters.
String writes to the console are buffered up the end of the line
or until the buffer fills. Then the buffer is flushed to all
console devices.
Existing low level console output via cnputc() is unaffected by
this change. ithread calls to log() are also unaffected to avoid
blocking those threads.
A minor change to the behaviour in a panic situation is that
console output will still be buffered, but won't be written to
a tty as before. This should prevent interspersed panic output
as a number of CPUs panic before we end up single threaded
running ddb.
Reviewed by: scottl, jhb
MFC after: 2 weeks
The 'nooption' kernel config entry has to be used to turn KSE off now.
This isn't my preferred way of dealing with this, but I'll defer to
scottl's experience with the io/mem kernel option change and the grief
experienced over that.
Submitted by: scottl@
syscalls using __syscall but only actually returning 32bits, such as mmap(),
specially : they set the return value in td->td_retval[0], but the userland
functions will expect this in r1, and not in r0 as it is normally done, as it
is the LSB. So add a special case for all these syscalls (all except lseek,
which truly returns 64bits).
Many thanks to Peter Grehan for his patience while explaining me the issue.
This interface also appears in the AT91SAM9260 and '61 as well as the
AVR32 based micros from Atmel. We don't yet support write protect or
hot-swap in this bridge driver.
Submitted by:
Reviewed by:
Approved by:
Obtained from:
MFC after:
Security:
Move the relocation definitions to the common elf header so that DTrace
can use them on one architecture targeted to a different one.
Add the additional ELF types defines in Sun's "Linker and Libraries"
manual.
KERNBASE and VM_MAXUSER_ADDRESS.
Remove the useless include of opt_global.h, as noticed by netchild@ (the one
in arm/elf_trampoline.c is legit, because this file is compiled outside the
kernel, and doesn't use the standard CFLAGS).
whole the physical memory, cached, using 1MB section mappings. This reduces
the address space available for user processes a bit, but given the amount of
memory a typical arm machine has, it is not (yet) a big issue.
It then provides a uma_small_alloc() that works as it does for architectures
which have a direct mapping.
Originally, I had adopted sparc64's name, pmap_clear_write(), for the
function that is now pmap_remove_write(). However, this function is more
like pmap_remove_all() than like pmap_clear_modify() or
pmap_clear_reference(), hence, the name change.
The higher-level rationale behind this change is described in
src/sys/amd64/amd64/pmap.c revision 1.567. The short version is that I'm
trying to clean up and fix our support for execute access.
Reviewed by: marcel@ (ia64)
mark system calls as being MPSAFE:
- Stop conditionally acquiring Giant around system call invocations.
- Remove all of the 'M' prefixes from the master system call files.
- Remove support for the 'M' prefix from the script that generates the
syscall-related files from the master system call files.
- Don't explicitly set SYF_MPSAFE when registering nfssvc.
implementations and adjust some of the checks while I'm here:
- Add a new check to make sure we don't return from a syscall in a critical
section.
- Add a new explicit check before userret() to make sure we don't return
with any locks held. The advantage here is that we can include the
syscall number and name in syscall() whereas that info is not available
in userret().
- Drop the mtx_assert()'s of sched_lock and Giant. They are replaced by
the more general checks just added.
MFC after: 2 weeks
The core uart code expects the receive method to actually puts the
characters read into its buffers. For AT91, it's done in the ipend routine,
so also check if we have the alternate break sequence here.
MFC after: 3 days
Introduce framework to configure the multiplexed pins on boot.
Since the USART supprots RS-485 multidrop mode, it allows the
TX pins to float. However, for RS-232 operations, we don't
want these pins to float. Instead, they should be pulled up
to avoid mismatches. Linux does something similar when it
configures the TX lines. This implies that we also allow the
RX lines to float rather than be in the state they are left in
by the boot loader. Since they are input pins, I think that
this is the right thing to do.
Plus minor for our board.
install custom pager functions didn't actually happen in practice (they
all just used the simple pager and passed in a local quit pointer). So,
just hardcode the simple pager as the only pager and make it set a global
db_pager_quit flag that db commands can check when the user hits 'q' (or a
suitable variant) at the pager prompt. Also, now that it's easy to do so,
enable paging by default for all ddb commands. Any command that wishes to
honor the quit flag can do so by checking db_pager_quit. Note that the
pager can also be effectively disabled by setting $lines to 0.
Other fixes:
- 'show idt' on i386 and pc98 now actually checks the quit flag and
terminates early.
- 'show intr' now actually checks the quit flag and terminates early.
address is in the userland address space. The proper thing is either to choose
a virtual address in the kernel address space beyond the KVA, or to use
pmap_mapdev().
we're unable to allocate the memory for a PTE, we'll wait until we can. If not,
we'll just return.
Use M_NOWAIT|M_USE_RESERVE to allocate PTEs, it is less aggressive than
M_NOWAIT alone.
Suggested by: alc
Make serial ports more robust and reliable. Make non-console ports
work. This might have broken skyeye stuff.
o Introduce ping-pong receive buffers.
o Use DMA to copy characters directly into memory.
o Support baud rates other than 115200
o Use 1 stop bit when 1 stop bit is requested (otherwise 2 were used,
which caused dropped characters when received in bursts).
o Use 1.5 stop bits for 5-bit bytes, and 2 stop bits otherwise when 2
stop bits were requested.
o Actually update line parameters.
o Fix comments
o Move init into attach
o Tweaks to TX interrupt registers to get them reliable and non-storming.
o harvest data in ipend since the latency between it and the callback
was too long. This likely is how it should be, I don't know why I deferred
things to the callback before.
o disable all interrupts in console init. We don't want interrupts until
we turn on an ISR.
o cosmetic tweaks
o Automatically detect of the TIMEOUT interrupt is supported. If so, use
it so we get better CPU utilization. Otherwise do a character at a time
RX. Good news here is that it seems we have enough CPU and low enough
fast interrupt latency to do this reliably.
o Don't read USART_CR. It is a write-only register.
o start to implement bus_ioctl. Do BAUD now...
number of banks, rows and columns the SDRAMC is programmed to access
to determine the RAM size for the board, rather than hard-wiring it to
be 32MB. My company's board with 64MB now probes correctly, as does
the KB9202 with only 32MB. This means that to detect the right memory
size, our boot loader must correctly initialize these values. This is
a fairly safe assumption because the boot loader has to initialize
SDRAM already, and it isn't really possible to change this register
after we've accessed SDRAM.
The boot loader is supposed to leave this bit set to the right value
for the board. If this bit was set at attach time, use it to init the
config register correctly.
Note: this means the boot loader has to properly initialize it.
an explicit comment that it's needed for the linuxolator. This is not the
case anymore. For all other architectures there was only a "KEEP THIS".
I'm (and other people too) running a COMPAT_43-less kernel since it's not
necessary anymore for the linuxolator. Roman is running such a kernel for a
for longer time. No problems so far. And I doubt other (newer than ia32
or alpha) architectures really depend on it.
This may result in a small performance increase for some workloads.
If the removal of COMPAT_43 results in a not working program, please
recompile it and all dependencies and try again before reporting a
problem.
The only place where COMPAT_43 is needed (as in: does not compile without
it) is in the (outdated/not usable since too old) svr4 code.
Note: this does not remove the COMPAT_43TTY option.
Nagging by: rdivacky
There is a race with the current locking scheme and removing
it should have no measurable performance impact.
This fixes page faults leading to panics in pmap_enter_quick_locked()
on amd64/i386.
Reviewed by: alc,jhb,peter,ps
- Try hard to calculate a safe sp, so that the stack doesn't get smashed
while uncompressing or relocating the kernel.
- Bring in code needed to calculate the cacheline size etc, needed for
arm9_idcache_wbinv_all.
current interface with the machine-independent layer. Without this change,
the page daemon would only have been awakened the first time that the
number of pv entries went above the high water mark, not each time.
the first and last cache line in PREREAD, and just invalidate the cache
lines in POSTREAD, instead of write-back/invalidating in POSTREAD, which
could lead to stale data overriding what has been transfered by DMA.
enabled. It has been commented out for a reason I forgot but I suspect
does not apply anymore.
Technically speaking it's not required to do it, has the data and the
instruction cache have been disabled in _start(). However, it may change
in the future, so I don't want to rely on this behavior.
Submitted by: kevlo