- Restart watchdog if we *did* processed any descriptors. [1]
- Log the watchdog event if the link is *up*. [2]
PR: kern/92948 [1]
Submitted by: Mihail Balikov <mihail.balikov interbgc.com> [1]
PR: kern/92895 [2]
Submitted by: Vladimir Ivanov <wawa yandex-team.ru> [2]
than just deleting them. Also add comments about why we do this.
Given the current behavior of delete_child, I don't think this changes
anything. It just feels cleaner.
dereferencing) since a NULL value would be a bug here.
Note: Both affected functions look very similar. A refactoring may
be beneficial.
CID: 483, 485
Found with: Coverity Prevent(tm)
Discussed with: ariff
MFC after: 5 days
needed here, except there's a bug which results in detaching the device
twice.
Move the NULL pointer check to the beginning of the function and convert
it into a KASSERT.
CID: 420
Found with: Coverity Prevent(tm)
Discussed with: ariff
MFC after: 5 days
Control) devices as console. These are microcontrollers which are either
on-board or part of an add-on card and provide terminal server, remote
power switch and monitoring functionality. For console usage these are
connected to the rest of the system via a SCC or an UART. This commit adds
support for the following variants (corresponds to what 'input-device' and
'output-device' have to be set to):
rsc found on-board in E250 and supposedly some Netra, connected
via a SAB82532, com. parameters can be determined via OFW
rsc-console RSC card found in E280R, Fire V4x0, Fire V8x0, connected
via a NS16550, hardwired to 115200 8N1
lom-console LOMlite2 card found in Netra 20/T4, connected via a NS16550,
hardwired to 9600 8N1
- Add my copyright to uart_cpu_sparc64.c as I've rewritten about one third
of that file over time.
Tested on: E250, E280R
Thanks to: dwhite@ for providing access to an E280R
OK'ed by: marcel
MFC after: 1 week
casting a structure to a uint32_t *. Many drivers in the tree do this, but
I'll not update them until these changes can be reviewed by the pedantic
standards folks.
in order to query the underlying Windows driver for the station address
and some other properties. There is a slim chance that the card may
receive a packet and indicate it up to us before ndis_attach() can call
ndis_halt_nic(). This is bad, because both the softc structure and
the ifnet structure aren't fully initialized yet: many pointers are
still NULL, so if we make it into ndis_rxeof(), we will panic.
To fix this, we need to do the following:
- Move the calls to IoAllocateWorkItem() to before the call to ndis_init_nic().
- Move the initialization of the RX DPC and status callback function pointers
to before ndis_init_nic() as well.
- Modify ndis_rxeof() to check if the IFF_DRV_RUNNING flag is set. If it
isn't, we return any supplied NDIS_PACKETs to the NIC without processing
them.
This fixes a crash than can occur when activating a wireless NIC in
close proximity to a very busy wireless network, reported by Ryan
Beasley (ryan%^$!ATgoddamnbastard-****!!!DOTorg.
MFC after: 3 days
are bus_addr_t, not bus_size_t.
In any case, turn off DAC support entirely until it is revamped to actually
work *correctly* for 64 bit platforms (not using a PAE definition and for
both initiator and target mode).
Treat SIOCADDMULTI and SIOCDELMULTI the same, since they had the same code
Remove redundant assignment to error
Convert to using the altq interface completely.
to sbus_mdvec.dv_clock as sbus_mdvec.dv_clock is meant to be specified
in MHz. While this was a bug it shouldn't have affected FreeBSD/sparc64
as sbus_mdvec.dv_clock is used to limit the clock rate of chips when
a machine isn't able to support them at maximum speed which isn't the
case for sun4u machines.
- Remove the code that checks whether the clock frequency returned by
sbus_get_clockfreq() is 0 and falls back to 25MHz if it is as that's
already done in sbus(4).
Approved by: mjacob
MFC after: 3 days
routines.
- Add or replace cpu_spinwait() with DELAY(1) to a few of the busy
loops when reading from the controller to work around firmware bugs
which can crash the controller.
with pseudo header for tcp/udp packets). This could save one in_pseudo() call
per incoming tcp/udp packet.
Approved by: glebius (mentor)
MFC after: 3 weeks
capability is present as not all devices supported by the agp_i810 driver
(such as i915) have the AGP capability. Instead, add an identify routine
to the agp_i810 driver that uses the PCI ID to determine if it should
create an agp child device.
to process. It could give us [significant?] perfomance increase if there is big
difference between RX/TX flows.
Submitted by: Mihail Balikov <mihail.balikov AT interbgc DOT com>
Approved by: glebius (mentor)
MFC after: 3 days
synchronized on every call of bge_poll_locked().
Suggested by: Mihail Balikov <mihail.balikov AT interbgc DOT com>
Approved by: glebius (mentor)
MFC after: 3 days
2) add missing bus_dmamap_sync() call in bge_intr()
Tested by: Husnu Demir <hdemir AT metu DOT edu DOT tr>
Approved by: glebius (mentor)
MFC after: 3 days
try to use the registrant for numbers in this file, not the OEM that
put their label on it. Use PNY's real number 0x154b. Add another PNY
atachmate with quirks from a PR filed a while ago, but that I can't
seem to find now...
from NetBSD. This driver actually can replace lnc(4). Advantages over
lnc(4) are:
- Cleaner and more flexible regarding MD needs.
- Endian-clean and MPSAFE.
- Supports ALTQ, VLAN_MTU, ifmedia.
- Uses 32bit DMA for the PCI variants.
This commit includes front-ends for the dma(4) pseudo-bus found on SBus-
based sparc64 machines (thus supports the on-board LANCE in Sun Ultra 1)
and PCI. In order to actually replace lnc(4), the front-ends for ISA and
the PC98 CBUS would have to be added but for which I don't have hardware
to test.
Reviewed and some improvements by: yongari
Tested on: i386, sparc64
support. Which reminds me that I'm not even sure if this works on _any_
laptop at all. :-o
PR: kern/90607
Submitted by: "Wojciech A. Koszek" <dunstan -at- freebsd.czest.pl>
MFC after: 3 days
This is supposed to fix some Coverity Prevent errors (Ariff didn't
looked at the CID's (ENOTIME), I just told him that there are some problems
in function dsp_ioctl()).
CID: 215-218
Found with: Coverity Prevent(tm)
Submitted by: ariff
MFC after: 5 days
o Change MEM_READ_1/MEM_READ_4 into macros (move them to if_iwireg.h)
o Add support for association LED
o Silently discard f/w notifications that are unknown (fixes spurious
"unknown notification 15" in logs with latest firmware)
o Fix scanning of 5GHz channels
into the card's memory.
# this eliminates a more of the ifdef soup in if_ed and if_edvar
# I've fixed the cbus drivers, but can't test them all easily.
If I've broken anything, please let me know.
to properly configure the right interface to use.
Also call the mediachg function when we set flags UP and are already
running. If this were a pure ifmedia driver, we'd not need to do this
since we'd be ignoring the linkX flags.
This reduces the number of ifdefs to support sub-devices a little as a
nice side effect. It also reduces the number of hpp interfaces
exposed by 33%.
man page that the ifconfig option link2 is used to disable the AUI
transceiver on the 3com boards (should also say HP PC Lan+). This
makes the connection clearer.
Add a note about why we set this flag prior to attaching the device.
We never set or clear the flag later, only test it. There can be no
races here, but this might be asthetically displeasing to some. Also
note that we may no longer need to have this knob at all as we may be
able to do it with the more sophisticated rc.d scripts we have today I
think the only reason it is there is because we didn't used to allow
its proper setting when configured to get the IP address via DHCP.
I'll note that this would be better handled by using ifmedia for all
ed cards, not just those with a miibus...
This is important with MegaLib, when issuing a GET_REBUILD_PROG since
it returns an error if the drive is not in rebuild state.
This will be MFC'ed shortly.
Submitted by: ps
Reviewed by: scottl
Found by: ambrisko
system LED on or off. Unlike the EBus LED AUXIO register where the
remaining bits are unused the upper bits of the SBus AUXIO register
are used to control other things like the link test enable pin of
the on-board NIC which we don't want to change as a side-effect.
- Remove the superfluous bzero()'ing of the softc obtained from
device_get_softc().
Reviewed by: yongari
MFC after: 3 days
Linux LSI MegaRaid tools can run on FreeBSD until Linux emulation.
Add in the Linux IOCTL shim and create the megadev0 device so
Linux LSI MegaRaid tools can run on FreeBSD until Linux emulation.
Add glue to build the modules but don't tie it into the build
yet until I test it from the CVS repo. via the mirror on an
amd64 machine.
Tie this into the Linux32 emulation on amd64 so the tools can
run on amd64 kernel.
Cleaned up by: ps (amr_linux.c)
side effect that legacy ATA controllers at irq14 and irq15 cannot share
interrupts with anything else without major problems.
This fixes the ATAPI DMA problems some systems/devices have seen.
(1) Fix DMA alignment, based on bytes per sample.
feeder_rate.c:
Handle strayed bytes (mostly caused by #1) better.
This DMA alignment issues are extremely hard to reproduce unless
the user happen to have a 32bit capable soundcards (ATI IXP) and
knowledgeable enough to force it to operate under pure 32bit
operations on both record and play directions.
up to date. Principle changes for this reelase is to support 2K Port Login
firmware. This allows us to support the 2322 (and 2422 4Gb) cards which only
come with the 2K Port Login firmware. The 2322 should now work- but we don't
have firmware sets for it in ispfw (as the change to load 2K Port Login f/w
hasn't been made- that f/w is so big it has to be loaded in more than one
chunk).
Other changes are the beginnings of cleaning up some long standing target
mode issues. The next changes here will incorporate a lot of bug fixes
from others.
Finally, some copyright cleanup and attempts to make the parts of the
driver that are FreeBSD specific start conforming more to FreeBSD style.
MFC after: 1 month
feeder.h:
feeder.c:
- Implement scoring mechanisme to select best format for conversion.
This is actually part of newer format chaining procedures which
will be commited someday. Confusion during chaining process solved
by this scoring since it will try to reduce list of from/to formats
to a single, best format.
Related PR: kern/91683
channel.c:
- Simplify feeder building process since we have smarter format
chaining.
feeder_fmt.c:
- Add few more sign conversion feeders for 24 and 32 bit format.
feeder_rate.c:
- Force buffer / bytes allignment. Unaligned buffer may cause
panics during recording on pure 32bit sample format if it
involves feeder_rate as part of feeders chain.
Tested on: ATI IXP, force 32bit recording.
MFC after: 5 days
o fix contention window
o silently discard received frames that are too short
o simplify lookup of 802.11a channels (we know they exist)
o fix short preamble support
o add short slot support
o fix eifs settings
o many consistency tweaks
share devclass pointers, a mistake I've encouraged in the past) and
move the declaration of the pci_driver kobj class from cardbus.c to
pci_private.h so that other drivers can inherit from pci_driver.
hacking:
- Remove all spaces at eol.
- Improve style(9) in most frequently edited functions.
- In em_encap() push variables for 82544 workaround in the block
where they are only used.
- In em_get_buf() remove unused variable.
as input/output interface errors.
- Keep values of rx/tx discards & tx collisions inside struct bge_softc.
So we can keep statistic across ifconfig down/up runs (cause bringing
bge up will reset chip).
Approved by: glebius (mentor)
MFC after: 1 week
ATI EHCI controllers exhibit simmilar stall issues and require
this dropped interrupts workaround. Be verbose about it.
ehci.c:
ehcivar.h:
Slight change in comments to note about issues surrounding both
VIA and ATI EHCI controllers.
Approved by: iedowse
an interrupt appears to occur before the transfer has been marked
as completed. This caused umass transfers to get stuck, especially
when writing large files. The workaround sets up a timer that
rechecks for missed completed transfers if some operations are still
pending. Other suggested workarounds, such as performing a PCI read
immediately after acknowledging the interrupts, do not appear to
help.
Obtained from: OpenBSD
same behavior to be controlled by the sysctls, hw.syscons.kbd_kbdkey
and hw.syscons.kbd_reboot respectively.
Apologies to the submitter for taking so long to commit this simple
change.
PR: kern/72728
Submitted by: Luca Morettoni <morettoni at libero dot it>
MFC After: 3 days
taskqueue_start_threads(struct taskqueue **, int count, int pri,
const char *name, ...);
This allows the creation of 1 or more threads that will service a single
taskqueue. Also rework the taskqueue_create() API to remove the API change
that was introduced a while back. Creating a taskqueue doesn't rely on
the presence of a process structure, and the proc mechanics are much better
encapsulated in taskqueue_start_threads(). Also clean up the
taskqueue_terminate() and taskqueue_free() functions to safely drain
pending tasks and remove all associated threads.
The TASKQUEUE_DEFINE and TASKQUEUE_DEFINE_THREAD macros have been changed
to use the new API, but drivers compiled against the old definitions will
still work. Thus, recompiling drivers is not a strict requirement.
- Add support for adjusting the fan speed if the fan control mode is manual
Documentation for the relevant embedded controller register was obtained from
http://www.thinkwiki.org/wiki/Patch_for_controlling_fan_speed
Tested on: R51 by Fabian Keil
T41p by markus
Requested by: many
Approved by: philip
MFC after: 1 week
2) use more robust way of link state handling for BCM5700 rev.B2 chip
3) workaround bug of some BCM570x chips which cause spurious "link up" messages
4) fix bug: some BCM570x chips was unable to detect link state changes after
ifconfig down/up sequence until any 'non-link related' interrupt generated.
(this happened due to pending internal link state attention which blocked
interrupt generation)
Approved by: glebius (mentor)
MFC after: 1 week
the the interface has been configured. I'm not sure how this could ever
have worked before, but it should be fixed now. Also break out the interrupt
degresitration function into it's own step.
before. The symptom is that the battery inform us its charge and discharge
at the same time...
* fix bst.rate to correctly output the (dis)charging rate. We'll use
the current average over one minute command and not the at_rate command.
Note that this method is not correct if the capacity_mode is set, but
since we don't set it ourself, it is not a problem.
The at_rate do not give the actual rate but is used to compute the
estimated time for (dis)charging a battery. We should actually
write an estimation of the actual rate using at_rate cmd and then
perform a read to the various estimators.
Approved by: njl
MFC after: 2 days
The minimum / maximum speed was way too low / high!
minspeed = 2000 - is this for real ?
maxspeed = 767999 - is this for real ?????
Wrap everything into 8000 - 48000 boundary, just to be safe.
MFC after: 3 days
- Mark MPSAFE since most of the locking procedures already implemented.
- Turn on inverted external amplifier sense flag for selected boards.
Tested by: bland
MFC after: 1 week
- Only update the rx ring consumer pointer after running through the rx loop,
not with each iteration through the loop.
- If possible, use a fast interupt handler instead of an ithread handler. Use
the interrupt handler to check and squelch the interrupt, then schedule a
taskqueue to do the actual work. This has three benefits:
- Eliminates the 'interrupt aliasing' problem found in many chipsets by
allowing the driver to mask the interrupt in the NIC instead of the
OS masking the interrupt in the APIC.
- Allows the driver to control the amount of work done in the interrupt
handler. This results in what I call 'adaptive polling', where you get
the latency benefits of a quick response to interrupts with the
interrupt mitigation and work partitioning of polling. Polling is still
an option in the driver, but I consider it orthogonal to this work.
- Don't hold the driver lock in the RX handler. The handler and all data
associated is effectively serialized already. This eliminates the cost of
dropping and reaquiring the lock for every receieved packet. The result
is much lower contention for the driver lock, resulting in lower CPU usage
and lower latency for interactive workloads.
The amount of work done in the taskqueue is controlled by the sysctl
dev.em.N.rx_processing_limit
and tunable
hw.em.rx_process_limit
Setting these to -1 effectively removes the limit.
The fast interrupt and taskqueue can be disabled by defining NO_EM_FASTINTR.
This work has been shown to increase fast-forwarding from ~570 kpps to
~750 kpps (note that the same NIC hardware seems unable to transmit more than
800 kpps, so this increase appears to be limited almost solely by the
hardware). Gains have been shown in other workloads, ranging from better
performance to elimination of over-saturation livelocks.
Thanks to Andre Opperman for his time and resources from his network
performance project in performing much of the testing. Thanks to Gleb
Smirnoff and Danny Braniss for their help in testing also.
Instead of dragging the entire ICH4/82801DB into this mess, select
only few boards based on pci subdevice / subvendor.
Tested by: Daisuke Orikasa <luxury-acura-3.5rl at nifty.com>
MFC after: 3 days
This is based on MCPC USB mobile phone guide line (MCPC-GL005)
Some other 3G system or so will work with this driver.
Kyocera PHS terminal (a.k.a. Kyopon) is known to work, which
is now supported by umodem(4) driver.
o record tsf in tx+rx frames
o switch from raw rssi to dbm for signal data and record both
signal and noise floor data (hacked for now to assume a fixed
noise floor; is correct with new hal)
o add monpass sysctl to control which rx'd frames are passed
up with errors; especially useful to see frames with CRC errors
o mark 'd packets w/ a CRC error with radiotap's BADFCS flag
Also add placeholder code for calibrating the noise floor when
using newer hals.
Reviewed by: avatar
MFC after: 1 week
better, I discovered sn doing too many pointer dereferences. This
driver would do silly things like:
sn_foo(struct ifnet *ifp)
{
struct sn_softc *sc = ifp->if_softc;
sc->ifp->mumble
/* Other stuff */
}
while /* other stuff */ usually needed sc, the extra deref isn't
needed. Eliminate a few dozen of them.
modules would have overlapping names.
- Only create /dev/si_control for unit 0.
Tested by: Joerg Lehners Joerg dot Lehners at informatik dot
uni-oldenburg dot de (on 6.x)
MFC after: 1 week
various pcib drivers to use their own private devclass_t variables for
their modules.
- Use the DEFINE_CLASS_0() macro to declare drivers for the various pcib
drivers while I'm here.
doesn't have any actual interrupts is listed in a _PRT entry, only print
a warning rather than panic'ing when we walk the _PRT's to build up count
of entries that reference a given link (the counts are used as weights so
that we can attempt to balance the load across IRQs used by link devices).
Instead, only panic if we attempt to use the _PRT entry to route an
interrupt for a device.
PR: i386/89545
Tested by: anders
- MPSAFE
- Fix / reorganize attach routine. Device specific initialization must
be done after generic bus / DMA setup. At last, Virtual Channels
(vchan) works as expected.
Note: Recent commit / fix against this driver proves that major enhancements
on the generic sound layer does indeed help to expose flaw within
device specific code. There are probably other drivers that need to
be addressed as well.
Tested by: barner
MFC after: 1 week
ifm_status and ifm_active. IFM_10_T gets set in the ifm_active field,
not in the ifm_status field, as far as I can tell.
Note: this was to enable a workaround that's rarely enabled. I don't know
how to corrupt my eeprom to test it, and would rather not know...
signal is received during the msleep, the msleep is retried
indefinitely as it just keeps returning ERESTART because of
the pending signal.
Instead, just don't PCATCH - the signal can wait.
Sponsored by: Sophos/ActiveState
requiried to keep consistent softc state before/after callback function
invocation and supposed to be sligntly faster than previous one as it
wouldn't incur callback overhead. With this change callback function
was gone.
- Decrease TI_MAXTXSEGS to 32 from 128. It seems that most mbuf chain
length is less than 32 and it would be re-packed with m_defrag(9) if
its chain length is larger than TI_MAXTXSEGS. This would protect ti(4)
against possible kernel stack overflow when txsegs[] is put on stack.
Alternatively, we can embed the txsegs[] into softc. However, that
would waste memory and make Tx/Rx speration hard when we want to
sperate Tx/Rx handlers to optimize locking.
- Fix dma map tracking used in Tx path. Previously it used the dma map
of the last mbuf chain in ti_txeof() which was incorrect as ti(4)
used dma map of the first mbuf chain when it loads a mbuf chain with
bus_dmamap_load_mbuf(9). Correct the bug by introducing queues that
keep track of active/inactive dma maps/mbuf chain.
- Use ti_txcnt to check whether driver need to set watchdog timer instead
of blidnly clearing the timer in ti_txeof().
- Remove the 3rd arg. of ti_encap(). Since ti(4) now caches the last
descriptor index(ti_tx_saved_prodidx) used in Tx there is no need to
pass it as a fuction arg.
- Change data type of producer/consumer index to int from u_int16_t in
order to remove implicit type conversions in Tx/Rx handlers.
- Check interface queue before getting a mbuf chain to reduce locking
overhead.
- Check number of available Tx descriptores to be 16 or higher in
ti_start(). This wouldn't protect Tx descriptor shortage but it would
reduce number of bus_dmamap_unload(9) calls in ti_encap() when we are
about to running out of Tx descriptors.
- Command NIC to send packets ony when the driver really has packets
enqueued. Previously it always set TI_MB_SENDPROD_IDX which would
command NIC to DMA Tx descriptors into NIC local memory regardless
of Tx descriptor changes.
Reviewed by: scottl
allocating a resource that's in the card itself.
Remove more now-redundant resource_list_add, and now-redunant code
that lives in the pci layer.
# This fixes the atheros card that I have which had its CIS in one of
# the BARs. Don't know yet if this fixes the amd64 issues reported.
USB HID device that allows to plug two PS2 controllers. This specific
device doesn't work yet but will as soon as we support devices with
multiple report IDs.
MFC after: 3 days
broken report descriptor. While I'm here, make all the other report
descriptors const to match the newly added one.
Obtained from: NetBSD
MFC after: 1 week
lack a report descriptor and don't use the standard interface class.
This patch works around these deficiencies so that the uhid(4) driver
can recognize and use those broken devices.
PR: usb/90141
Submitted by: Ed Schouten <ed@fxq.nl> (with minor mods from me)
MFC after: 1 week
force allocation of unallocated BARs (cardbus uses this to preallocate
everything). Add a prefetchmask to allow for busses that get prefetch
hints to set them. Addjust pci_add_map and pci_ata_maps to take a new
force flag which pci_add_resources will pass in. Implement 'force' in
pci_add_map. Write new value of allocated resource into the bar, if
the allocation succeeded (we should have done this before, but with
the new force the bug was very obvious).
This should reduce huge playback / recording latency for
applications that try to act smarter and manage their own
buffering (XMMS, Skype, etc.).
Note to Skype + via8xxx users: Remove previous hackish
"hint.pcm.<unit>.via_dxs_disabled" from kernel hint and see
whether this changes cure all those annoying sound issues.
try very hard to be perfect. However, these attempts broke down when
there were large numbers of resources. We'd not be able to map them all.
Instead, accept that we might pass more range to thse subbus than
might be optimal be able to compute. However, there's little harm in
this and it allows us to pass greater resources through.
# it has been suggested that we allocate a fixed amount of resources
# on attach and give it out upon request. This might not be a bad idea...
cardbus_cis.c to this file, some code was not merged and thus resource
list entries were invalid. They didn't have a resources attached to
them.
However, the problem was masked for some time later, because newer
resources list entries were added to the head of the list, and
resource_list_find() always returned the first matching resource list
entry. Usually the underlying driver allocated a valid resource and
added it to the head of the list, and invalid one wasn't used.
In rev. 1.174 of subr_bus.c the sorting of resource list entries was
reversed demasking the problem in cardbus_alloc_resources().
This commit fixes the problem returning back some code from
cardbus_cis.c, pre-1.49 revisions.
PR: kern/87114
PR: kern/90441
Hardware provided by: Vasily Olekhov <olekhov yandex.ru>
Reviewed by: imp
. remove unnecessay header files after Scott's bus_dma(9) commit.
. remove global variable tis which was introduced at the time of
zero_copy(9) changes. The variable tis was not used at all. The
same applyes to ti_links in softc so axe it.
. deregister variables.
. axe ti_vhandle and switch to use explicit register access for
accessing NIC local memory. Creates three variants of ti_mem to
read/write NIC local memory(ti_mem_read, ti_mem_write) and clearing
NIC local memory(ti_mem_zero). This greatly enhances code
readability and have ti(4) drop using shared memory scheme for
Tigon 1. As Tigon 1 switched to use explicit register access for Tx,
axe ti_tx_ring_nic/ti_cmd_ring in softc.(Tigon 2 used to host ring
scheme which means there is no need to access NIC local memory via
register access for Tx and NIC would DMA the modified Tx rings into
its local memory.) [1]
. introduce new macro TI_EVENT_*/TI_CMD_* to handle NIC envent/command.
Instead of using bit fields assginment for accessing the event, use
shift operations to set/get it. [1]
. add additional check for valid DMA tags in ti_free_dmamaps().
. add missing bus_dmamap_sync/bus_dmamap_unload in ti_free_*_ring_*.
. fix locking nits(MTX_RECURSE mutex) and make ti(4) MPSAFE.
. change data type of ti_rdata_phys to bus_addr_t and don't blindly
cast to uint32_t.
. rearrange detach path and make ti(4) survive during device detach.
. for Tigon 1, use explicit register access for checking Tx descriptors
in ti_encap()/ti_txeof(). [1]
. properly call bus_dmamap_sync(9) for updating statistics.
. remove extra semicolon in ti_encap()
. rewrite loading MAC address to work on strict-alignment architectures.
. move TI_RD_OFF macro to if_tireg.h
. axe ETHER_ALIGN as it's already defined in <net/ethernet.h>.
. make macros immuine from expansion by adding parenthesis and do-while.
. remove alpha specific hack as vtophys(9) is no longer used in ti(4)
after Scott's bus_dma(9) fix.
Reviewed by: scottl
Obtained from: OpenBSD [1]
