(mostly with Catalan characters in mind, but it probably
benefits other languages).
The new mappings are as follows:
▮ -> █
ÀÈÍÏÓÒÚ -> AEIIOOU
ŀ / Ŀ -> l / L
Reviewed by: ed
Approved by: kib (mentor)
I found this useful when trying to debug the AR9160 STA RX filter issue -
I'd get crypto reply errors but it wasn't entirely clear which TID it
was for.
their length.
Without this, an error frame mbuf would:
* have its size adjusted;
* thrown at the radiotap code;
* then since it's never consumed, the rxbuf/mbuf is then re-added to the
RX descriptor list with the small size;
* .. and the hardware ends up (sometimes) only DMA'ing part of a frame into
the small buffer, chaining RX frames together (setting the more flag).
I discovered this particular issue when doing some promiscuous radiotap
testing; I found that I'd occasionally get rs_more set in RX descriptors
w/ the first frame length being very small (sub-100 bytes.) The driver
handles 2-descriptor RX frames (but not more), so this still worked; it
was just odd.
This is suboptimal and may benefit from being replaced with caching
the m_pkthdr_len and m_len fields, then restoring them after completion.
providers and consumers will be destroyed. Before take some actions
with a geom, check that it is not destroyed at the moment.
Tested by: nwhitehorn
MFC after: 1 week
bge(4) sends BGE_FW_CMD_DRV_ALIVE command to firmware every 2
seconds. BGE_FW_CMD_DRV_ALIVE command requires 4 bytes data. This
data contains timeout value in seconds until the next
BGE_FW_CMD_DRV_ALIVE command.
Broadcom recommends driver set the value 3 times longer than the
interval that it sends BGE_FW_CMD_DRV_ALIVE. Currently bge(4) uses
3 seconds so probably we have to increase it in future and use
different ALIVE command(e.g. BGE_FW_CMD_DRV_ALIVE3).
No functional changes.
This bit(SW event 7 in publicly available data sheet) is used to
make RX CPU handle a firmware command and the bit is automatically
cleared after RX CPU completed the command.
Generally firmware command takes the following steps.
1. Write BGE_SRAM_FW_CMD_MB with a command.
2. Write BGE_SRAM_FW_CMD_LEN_MB with the length of the command in bytes.
3. Write BGE_SRAM_FW_CMD_DATA_MB with actual command data.
4. Generate BGE_RX_CPU_EVENT and let firmware handle the command.
5. Wait for the ACK of the firmware command.
No functional changes.
it no longer exists). Instead, run svnversion if we can find the binary
and test that the output looks like a version string.
Reviewed by: discussion on -current@
Tested by: rodrigc for non-svn case (thanks!)
start only one worker thread. For software crypto it will start by default
N worker threads where N is the number of available CPUs.
This is not optimal if hardware crypto is AES-NI, which uses CPU for AES
calculations.
Change that to always start one worker thread for every available CPU.
Number of worker threads per GELI provider can be easly reduced with
kern.geom.eli.threads sysctl/tunable and even for software crypto it
should be reduced when using more providers.
While here, when number of threads exceeds number of CPUs avilable don't
reduce this number, assume the user knows what he is doing.
Reported by: Yuri Karaban <dev@dev97.com>
MFC after: 3 days
- Operate on uint64_t types when doing XORing, etc. instead of uint8_t.
- Don't bzero() temporary block for every AES block. Do it once for entire
data block.
- AES-NI is available only on little endian architectures. Simplify code
that takes block number from IV.
Benchmarks:
Memory-backed md(4) device, software AES-XTS, 4kB sector:
# dd if=/dev/md0.eli bs=1m
59.61MB/s
Memory-backed md(4) device, old AES-NI AES-XTS, 4kB sector:
# dd if=/dev/md0.eli bs=1m
97.29MB/s
Memory-backed md(4) device, new AES-NI AES-XTS, 4kB sector:
# dd if=/dev/md0.eli bs=1m
221.26MB/s
127% performance improvement between old and new code.
Harddisk, raw speed:
# dd if=/dev/ada0 bs=1m
137.63MB/s
Harddisk, software AES-XTS, 4kB sector:
# dd if=/dev/ada0.eli bs=1m
47.83MB/s (34% of raw disk speed)
Harddisk, old AES-NI AES-XTS, 4kB sector:
# dd if=/dev/ada0.eli bs=1m
68.33MB/s (49% of raw disk speed)
Harddisk, new AES-NI AES-XTS, 4kB sector:
# dd if=/dev/ada0.eli bs=1m
108.35MB/s (78% of raw disk speed)
58% performance improvement between old and new code.
As a side-note, GELI with AES-NI using AES-CBC can achive native disk speed.
MFC after: 3 days
thing when changing the debugging options as part of head becoming a new
stable branch. It may also help people who for one reason or another want
to run head but don't want it slowed down by the debugging support.
Reviewed by: kib
more general VM system interfaces. So, their implementation can now
reside in kern_malloc.c alongside the other functions that are declared
in malloc.h.
about the various driver events like load, unload, reset, suspend,
restart, and ioctl operations.
Define driver's event rather than using hard-coded values. We don't
still send suspend/resume event to firmware.
Previously bge(4) used BGE_SDI_STATUS to send events. Because driver
has to access firmware mail box to inform current state, using
BGE_SDI_STATUS register was wrong. The end result was the same as
BGE_SDI_STATUS is 0x0C04.
No functional changes.
- add support for volumes above 2TiB with Promise metadata format;
- enforse and document other limitations:
- Intel and Promise metadata formats do not support disks above 2TiB;
- NVIDIA metadata format does not support volumes above 2TiB.
Sponsored by: iXsystems, Inc.
MFC after: 2 weeks
The origin of GENCOMM seems to come from Alteon Tigon Host/NIC
interface definition where it defines general communications region
which is active when firmware is loaded and running. This region
was used in communication between the host and processor internal
to the Tigon chip.
Broadcom data sheet also defines the region as 'Software Gencomm'
in NetXtreme memory map but lacks detailed description of its
interface so it was hard to know which ones are used for which
interface.
This change shall slightly enhance readability.
No functional changes.
larger than 4KB in size. However the maximum DMA segment size
created in DMA tag is 4KB, so we wouldn't encounter the issue here.
Just record this issue such that let developers not to create a DMA
segment that is larger than 4KB for BCM5719. It's possible to split
a DMA segment into multiple smaller ones in run time but I believe
it's not worth to implement that.
o Protect bge(4) status block access and register dump with driver lock.
o Add missing bus_dmamap_sync() before dumping status block.
o Use minimum status block size, 32 bytes, for status block dump on most
controllers except BCM5700 AX/BX.
While I'm here, make the handler show 5717 Plus in hardware flags.
* preserve AR_TxIntrReq on every descriptor in an aggregate chain,
not just the first descriptor;
* always blank out the descriptor in ar5416ChainTxDesc() when forming
aggregates - the way I'm using this in the 11n branch is to first
chain aggregates together, then use the other HAL calls to fill in
the details.
* Add the TID field in the TX status descriptor;
* Add in the 11n first/middle/last functions for fiddling
with the descriptors. These are from the Linux and the
reference driver, but I'm not (currently) using them.
* Add further AR_ISR_S5 register definitions.
Obtained from: Linux ath9k, Atheros
interfere with traffic, as the NF load can take quite a while and poking the
AGC every 10uS is just a bit silly.
Instead, just leave the baseband NF calibration where it is and just read it
back next time a longcal interval happens.
and constants related to the BIOS Enhanced Disk Drive Specification.
- Use this header instead of magic numbers and various duplicate structure
definitions for doing I/O.
- Use an actual structure for the request to fetch drive parameters in
drvsize() rather than a gross hack of a char array with some magic
size. While here, change drvsize() to only pass the 1.1 version of
the structure and not request device path information. If we want
device path information you have to set the length of the device
path information as an input (along with probably checking the actual
EDD version to see which size one should use as the device path
information is variable-length). This fixes data smashing problems
from passing an EDD 3 structure to BIOSes supporting EDD 4.
Reviewed by: avg
Tested by: Dennis Koegel dk neveragain.de
MFC after: 1 week
controller.
AX88772B data sheet does not show detailed information about
checksum offloading related things. It seems the controller has
lots of options to support checksum offloading but I failed to
understand why this feature requires so much complex controller
configuration and status bits.
One of major difference between AX88772B and its predecessor is
AX88772B uses a new RX header format when RX checksum offloading is
enabled. It also requires the received length of a frame should be
multiple of 4. Controller will pad necessary bytes to make the
length of received frame to be multiple of 4. It is driver's
responsibility to offset this pad bytes.
Note, AX88772B could be configured to get partial checksum value in
in RX header. This mode uses different RX header format and
currently we don't use that fature.
This change makes axe(4) use driver specific MII attach handler to
override uether(9)'s default MII attach and announce flow-control
capability for AX88178/AX88772A/AX88772B to PHY drivers. It seems
original AX88772 also supports flow-control but I didn't enable it
due to lack of test/access to the controller. The flow-control
threshold parameter is loaded from EEPROM and there is no way to
override this value without reprogramming EEPROM. For AX88772B,
TX/RX IP/TCP/UDP checksum offloading is announced to network stack.
IPv6 and PPPoE checksum offloading is also supported by controller
but we have no way to take advantage of these features.
Driver already knows PHY address so make PHY driver know that
information and remove unnecessary PHY address check used in
miibus_readreg/miibus_writereg callbacks. Also announce AX88178,
AX88772A and AX88772B support VLAN over-sized frame.
While I'm here clean up headers and remove axe_start() in
axe_init() because the link wouldn't be available right after media
change.
common cases that can be handled in constant time. The insight being
that a page's parent in the vm object's tree is very often its
predecessor or successor in the vm object's ordered memq.
Tested by: jhb
MFC after: 10 days
with older FreeBSD versions:
- Add -V option to 'geli init' to specify version number. If no -V is given
the most recent version is used.
- If -V is given don't allow to use features not supported by this version.
- Print version in 'geli list' output.
- Update manual page and add table describing which GELI version is
supported by which FreeBSD version, so one can use it when preparing GELI
device for older FreeBSD version.
Inspired by: Garrett Cooper <yanegomi@gmail.com>
MFC after: 3 days
of the CDDL licence explicitly requires every Contributor to add
a copyright notice.
This also reflects the copyright notices for the changes recently
added by Illumos.
MFC after: 3 days
interfaces. A host route has a NULL mask so check for that condition.
I have also been told by developers who customize the packet output
path with direct manipulation of the route entry (or the outgoing
interface to be specific). This patch checks for the route mask
explicitly to make sure custom code will not panic.
PR: kern/161805
MFC after: 3 days
masked out when adding a prefix route through the "route" command.
However, when deleting the route, simply changing the command keyword
from "add" to "delete" does not work. The failoure is observed in
both IPv4 and IPv6 route insertion. The patch makes the route command
behavior consistent between the "add" and the "delete" operation.
MFC after: 1 week
handler such that driver can announce interface capabilities and
can do its own MII attach. Currently all USB ethernet controllers
have no way to establish a link with pause capabilities. Lack of
checksum offloading support also was one of reason to bring this
change in.
This change adds a couple of wrappers to USB ethernet drivers
(uether_ifmedia_upd, uether_init and uether_start). All exported
functions in uether has prefix uether_ so I think it's more
consistent to have wrappers that follow the convention.
This change preserves ABI/KPI so it should be safe to merge this
change to stable/8.
While I'm here add missing __FBSDID and clean up headers.
Reviewed by: hselasky
controller which is found on ULi M1563 South Bridge & M1689 Bridge.
These controllers look like a tulip clone.
M5263 controller does not support MII bitbang so use DC_ROM
register to access MII registers. Like other tulip variants, ULi
controller uses a setup frame to configure RX filter and uses new
setup frame format. It's not clear to me whether the controller
supports a hash based multicast filtering so this patch uses 14
perfect multicast filter to filter multicast frames. If number of
multicast addresses is greater than 14, controller is put into a
mode that receives all multicast frames.
Due to lack of access to M5261, this change was not tested with
M5261 but it probably works. Many thanks to Marco who provided
remote access to M5263.
Tested by: Marco Steinbach <coco <> executive-computing dot de>,
Martin MATO <martin.mato <> orange dot fr>
link such that calling dc_setcfg() right after media change would
be meaningless unless controller in question is not Davicom DM9102.
Ideally dc_setcfg() should be called when speed/duplex is resolved
otherwise it would reprogram controller with wrong speed/duplex
information. Because MII status change callback already calls
dc_setcfg() I think calling dc_setcfg() in dc_init_locked() is
wrong. For instance, it would take some time to establish a link
after mii_mediachg(), so blindly calling dc_setcfg() right after
mii_mediachg() will always yield wrong media configuration.
Extend dc_ifmedia_upd() to handle media change and still allow
21143 and Davidcom controllers program speed/duplex regardless of
current resolved speed/duplex of link. In theory 21143 may not need
to call dc_setcfg() right after media change, but leave it as it is
because there are too many variants to test that change. Probably
dc(4) shall need a PHY reset in dc_ifmedia_upd() but it's hard to
verify correctness of the change.
This change reliably makes ULi M5263 establish a link.
While I'm here correctly report media change result. Previously it
always reported a success.
failure (the getnewvnode cannot return an error). In this case, the
null_insmntque_dtr() already unlocked the reclaimed vnode, so VOP_UNLOCK()
in the nullfs_mount() after null_nodeget() failure is wrong.
Tested by: pho
MFC after: 1 week
- for the legacy PCI ATA channels move channel number out of the device
description, same as it is for ahci(4), siis(4) and mvs(4);
- add device description for the ISA ATA channels.
where the driver assumed that BA resources are still available due to
net80211 saying so.
PR: 161407, 159768
Tested by: cperciva, rene
MFC after: 3 days
It is possible for file systems with 'mountpoint' preperty set to 'legacy'
or 'none' - we don't have to change mount directory for them.
Currently such file systems are unmounted on rename and not even mounted back.
This introduces layering violation, as we need to update 'f_mntfromname'
field in statfs structure related to mountpoint (for the dataset we are
renaming and all its children).
In my opinion it is worth it, as it allow to update FreeBSD in even cleaner
way - in ZFS-only configuration root file system is ZFS file system with
'mountpoint' property set to 'legacy'. If root dataset is named system/rootfs,
we can snapshot it (system/rootfs@upgrade), clone it (system/oldrootfs),
update FreeBSD and if it doesn't boot we can boot back from system/oldrootfs
and rename it back to system/rootfs while it is mounted as /. Before it was
not possible, because unmounting / was not possible.
MFC after: 2 weeks
This restores the previous behaviour. While here, match '?' and '.'
inputs exactly and improve the error message.
Requested by: avg@
Derived from a patch by: Arnaud Lacombe <lacombar@gmail.com>
of scheduling next run pfsync_bulk_update(), pfsync_bulk_fail()
was scheduled.
This lead to instant 100% state leak after first bulk update
request.
- After above fix, it appeared that pfsync_bulk_update() lacks
locking. To fix this, sc_bulk_tmo callout was converted to an
mtx one. Eventually, all pf/pfsync callouts should be converted
to mtx version, since it isn't possible to stop or drain a
non-mtx callout without risk of race.
- Add comment that callout_stop() in pfsync_clone_destroy() lacks
locking. Since pfsync0 can't be destroyed (yet), let it be here.
The root of problem is re-locking at the end of pfsync_sendout().
Several functions are calling pfsync_sendout() holding pointers
to pf data on stack, and these functions expect this data to be
consistent.
To fix this, the following approach was taken:
- The pfsync_sendout() doesn't call ip_output() directly, but
enqueues the mbuf on sc->sc_ifp's interfaces queue, that
is currently unused. Then pfsync netisr is scheduled. PF_LOCK
isn't dropped in pfsync_sendout().
- The netisr runs through queue and ip_output()s packets
on it.
Apart from fixing race, this also decouples stack, fixing
potential issues, that may happen, when sending pfsync(4)
packets on input path.
Reviewed by: eri (a quick review)
o Detect when Boot Camp is enabled (i.e. the MBR mirrors the GPT).
o When Boot Camp is enabled, update the MBR whenever we write the GPT.
o Creation of a Boot Camp enabled GPT is not supported.
o Automatically disable Boot Camp when the GPT has been changed so that
there's either no EFI partition or no HFS+ partition.
o The first 4 partitions (by index) get mirrored in the MBR.
Requested by, discussed with and tested by: kris@pcbsd.org
MFC after: 1 week
