required by video card drivers. Specifically, this change introduces
vm_cache_mode_t with an appropriate VM_CACHE_DEFAULT definition on all
architectures. In addition, this changes adds a vm_cache_mode_t parameter
to kmem_alloc_contig() and vm_phys_alloc_contig(). These will be the
interfaces for allocating mapped kernel memory and physical memory,
respectively, with non-default cache modes.
In collaboration with: jhb
in Freescale system-on-chip devices.
The following algorithms and schemes are currently supported:
- 3DES, AES, DES
- MD5, SHA1, SHA256, SHA384, SHA512
Reviewed by: philip
Obtained from: Freescale, Semihalf
- make mftb() shared, rewrite in C, provide complementary mttb()
- adjust SMP startup per the above, additional comments, minor naming
changes
- eliminate redundant TB defines, other minor cosmetics
Reviewed by: marcel, nwhitehorn
Obtained from: Freescale, Semihalf
new platform module. These are probed in early boot, and have the
responsibility of determining the layout of physical memory, determining
the CPU timebase frequency, and handling the zoo of SMP mechanisms
found on PowerPC.
Reviewed by: marcel, raj
Book-E parts by: raj
controller in the VIA southbridge functional in the CDS
(Configurable Development System) for MPC85XX.
The embedded USB controllers look operational but the
interrupt steering is still wrong.
a fair number of static data structures, making this an unlikely
option to try to change without also changing source code. [1]
Change default cache line size on ia64, sparc64, and sun4v to 128
bytes, as this was what rtld-elf was already using on those
platforms. [2]
Suggested by: bde [1], jhb [2]
MFC after: 2 weeks
CACHE_LINE_SIZE constant. These constants are intended to
over-estimate the cache line size, and be used at compile-time
when a run-time tuning alternative isn't appropriate or
available.
Defaults for all architectures are 64 bytes, except powerpc
where it is 128 bytes (used on G5 systems).
MFC after: 2 weeks
Discussed on: arch@
replace magic numbers with constants to keep this from happening again.
Without this fix, some programs would occasionally get SIGTRAP instead
of SIGILL on an illegal instruction. This affected Altivec detection
in pixman, and possibly other software.
Reported by: Andreas Tobler
MFC after: 1 week
CPUs known to use 128 byte cache lines and defaulting to 32, use the dcbz
instruction to measure it. Also make dcbz behave the way you would
expect on PPC 970.
on a generic dumper that creates an ELF core file and
uses PMAP functions to scan and iterate over memory
chunks, as well as handle memory mappings used during
dumping.
the PMAP layer can choose to return physical memory
chunks or virtual memory chunks. For minidumps, the
chunks should be virtual.
The default MMU I/F implementation for the scan_md()
method returns NULL. Thus, when a PMAP implementation
does not implement the required methods, an empty
core file is created. Here, empty means having an ELF
header only.
Obtained from: Juniper Networks
provided, for example, on the PowerPC 970 (G5), as well as on related CPUs
like the POWER3 and POWER4.
This also adds support for various built-in hardware found on Apple G5
hardware (e.g. the IBM CPC925 northbridge).
Reviewed by: grehan
to the full path of the image that is being executed.
Increase AT_COUNT.
Remove no longer true comment about types used in Linux ELF binaries,
listed types contain FreeBSD-specific entries.
Reviewed by: kan
Previously, DBCR0 flags were set "globally", but this leads to problems
because Book-E fine grained debug settings work only in conjuction with the
debug master enable bit in MSR: in scenarios when the DBCR0 was set with
intention to debug one process, but another one with MSR[DE] set got
scheduled, the latter would immediately cause debug exceptions to occur upon
execution of its own code instructions (and not the one intended for
debugging).
To avoid such problems and properly handle debugging context, DBCR0 state
should be managed individually per process.
Submitted by: Grzegorz Bernacki gjb ! semihalf dot com
Reviewed by: marcel
o Eliminate tlb0[] (a s/w copy of TLB0)
- The table contents cannot be maintained reliably in multiple MMU
environments, where asynchronous events (invalidations from other cores)
can change our local TLB0 contents underneath.
- Simplify and optimize TLB flushing: system wide invalidations are
performed using tlbivax instruction (propagates to other cores), for
local MMU invalidations a new optimized routine (assembly) is introduced.
o Improve and simplify TID allocation and management.
- Let each core keep track of its TID allocations.
- Simplify TID recycling, eliminate dead code.
- Drop the now unused powerpc/booke/support.S file.
o Improve page tables management logic.
o Simplify TLB1 manipulation routines.
o Other improvements and polishing.
Obtained from: Freescale, Semihalf
of OFW access semantics, in order to allow future support for real-mode
OF access and flattened device frees. OF client interface modules are
implemented using KOBJ, in a similar way to the PPC PMAP modules.
Because we need Open Firmware to be available before mutexes can be used on
sparc64, changes are also included to allow KOBJ to be used very early in
the boot process by only using the mutex once we know it has been initialized.
Reviewed by: marius, grehan
the code for parsing interrupt maps) to PowerPC and reflect their new MI
status by moving them to the shared dev/ofw directory.
This commit also modifies the OFW PCI enumeration procedure on PowerPC to
allow the bus to find non-firmware-enumerated devices that Apple likes to add,
and adds some useful Open Firmware properties (compat and name) to the pnpinfo
string of children on OFW SBus, EBus, PCI, and MacIO links. Because of the
change to PCI enumeration on PowerPC, X has started working again on PPC
machines with Grackle hostbridges.
Reviewed by: marius
Obtained from: sparc64
and ifnet functions
- add memory barriers to <machine/atomic.h>
- update drivers to only conditionally define their own
- add lockless producer / consumer ring buffer
- remove ring buffer implementation from cxgb and update its callers
- add if_transmit(struct ifnet *ifp, struct mbuf *m) to ifnet to
allow drivers to efficiently manage multiple hardware queues
(i.e. not serialize all packets through one ifq)
- expose if_qflush to allow drivers to flush any driver managed queues
This work was supported by Bitgravity Inc. and Chelsio Inc.
simplifies certain device attachments (Kauai ATA, for instance), and makes
possible others on new hardware.
On G5 systems, there are several otherwise standard PCI devices
(Serverworks SATA) that will not allow their interrupt properties to be
written, so this information must be supplied directly from Open Firmware.
Obtained from: sparc64
all to date and the latter also is only used in ia64 and powerpc
code which no longer serves a real purpose after bring-up and just
can be removed as well. Note that architectures like sun4u also
provide no means of implementing IPI'ing a CPU itself natively
in the first place.
Suggested by: jhb
Reviewed by: arch, grehan, jhb
volatile so that the compiler won't perform CSE. For SMP,
this may result in us accessing the wrong PCPU and as such
results in a bogus curthread value.
Note that getting curthread is not quite MP-safe in the sense
that it requires two instructions that aren't performed
atomically. The first instruction gets the address of the PCPU
structure and the second instruction dereferences that pointer
to get curthread. If a thread is switched-out in between these
instructions and switched-in on a different CPU, we still get
the wrong curthread.
