* Shuffle some of the capability numbers around to match the
Atheros HAL capability IDs, just for consistency.
* Add some new capabilities to FreeBSD from the Atheros
HAL which will be be shortly used when new chipsets are added
(HAL SGI-20 support is for Kiwi/AR9287 support); for
TX aggregation (MBSSID aggregate support, WDS aggregation
support); CST/GTT support for carrier sense/TX timeout.
These describe FCC/Japan channel and DFS behaviour.
The AR9285 and later chips don't set these bits in the eeprom, the correct
behaviour is to just assume all five bits are enabled.
upper-level HAL.
Right now the per-chain noise floor values aren't used anywhere in
the upper-level HAL, so the driver currently has no real reference
to compare the per-chain RSSI values to.
This is needed before per-chain RSSI values (for ctl and ext radios)
are can be thrown upstairs to the net80211 code.
At least one AR5416 user has reported measurable throughput drops
with this option. For now, disable it and make it a run-time
twiddle. It won't take affect until the next radio programming
trip though (eg channel scan, channel change.)
rather than duplicating them for the v14 (ar5416+) and v4k (ar9285) codebases.
Further chipsets (eg the AR9287) have yet another EEPROM format which will use
these routines to calculate things.
The earlier way of doing debugging would evaluate the function parameters
before calling the HALDEBUG. In the case of detailed register debugging
would mean a -lot- of unneeded register IO and other stuff was going on.
This method evaluates the ath_hal_debug variable before the function
parameters are evaluated, drastically reducing the amount of overhead
enabling HAL debugging during compilation.
putting descriptors (not buffers) across a 4k page boundary can cause issues.
I've not seen it in production myself but it apparently can cause problems.
So, in preparation for addressing this workaround, (re)-expose the particular
HAL capability bit which marks whether the chipset has support for cross-4k-
boundary transactions or not.
A subsequent commit will modify the descriptor allocation to avoid allocating
descriptor entries that straddle a 4k page boundary.
The higher levels (net80211, if_ath, ath_rate) need this to make correct
choices about what MCS capabilities to advertise and what MCS rates are
able to be TXed.
In summary:
* AR5416 - 2/3 antennas, 2x2 streams
* AR9160 - 2/3 antennas, 2x2 streams
* AR9220 - 2 antennas, 2x2 sstraems
* AR9280 - 2 antennas, 2x2 streams
* AR9285 - 2 antennas but with antenna diversity, 1x1 stream
The AR9100 at least doesn't have an external serial EEPROM
attached to the MAC; it instead stores the calibration data
in the normal system flash.
I believe earlier parts can do something similar but I haven't
experienced it first-hand.
This commit introduces an eepromdata pointer into the API but
doesn't at all commit to using it. A future commit will
include the glue needed to allow the AR9100 support code
to use this data pointer as the EEPROM.
Since we now have the source code, there's no reason to hide the diag codes
from other areas.
They live in the HAL as they form part of the HAL API and should still be treate
as "potentially flexible; don't publish as a public API." But since they're
already used as a public API (see follow-up commit), we may as well use
them in place of magic constants.
o rename the new variables to comply with the naming scheme
o move the new variables to an AR5212 specific struct
o use ahp when available
o revert to previous ts_flags check
o add HAL_CAP_BSSIDMATCH to identify parts that have the support for
disabling bssid match
o honor capability for set/get rx filter
o use HAL_CAP_BSSIDMATCH in driver to decide whether to use the bssid
match disable or fall back to promisc mode
Reviewed by: rpaulo
Approved by: re (rwatson)
o add ah_configPCIE and ah_disablePCIE for drivers to configure PCIE
power save operation (modeled after ath9k, may need changes)
o add private state flag to indicate if device is PCIE (replaces private
hack in 5212 code)
o add serdes programming ini bits for 5416 and later parts and setup
for each part (5416 and 9160 logic hand-crafted from existing routines);
5212 remains open-coded but is now hooked in via ah_configPCIE
o add PCIE workaround gunk
o add ar5416AttachPCIE for iodomatic code used by 5416 and later parts
o mark phy type to indicate 1/2 or 1/4-rate operation
o use phy type instead of channel attributes to identify 1/2 and 1/4-rate
operation
o general cleanup of code including move phy constants to ah_internal.h
Eventually this code should go away and we should use the net0211 equivalents.
o remove HAL_CHANNEL; convert the hal to use net80211 channels; this
mostly involves mechanical changes to variable names and channel
attribute macros
o gut HAL_CHANNEL_PRIVATE as most of the contents are now redundant
with the net80211 channel available
o change api for ath_hal_init_channels: no more reglass id's, no more outdoor
indication (was a noop), anM contents
o add ath_hal_getchannels to have the hal construct a channel list without
altering runtime state; this is used to retrieve the calibration list for
the device in ath_getradiocaps
o add ath_hal_set_channels to take a channel list and regulatory data from
above and construct internal state to match (maps frequencies for 900MHz
cards, setup for CTL lookups, etc)
o compact the private channel table: we keep one private channel
per frequency instead of one per HAL_CHANNEL; this gives a big
space savings and potentially improves ani and calibration by
sharing state (to be seen; didn't see anything in testing); a new config
option AH_MAXCHAN controls the table size (default to 96 which
was chosen to be ~3x the largest expected size)
o shrink ani state and change to mirror private channel table (one entry per
frequency indexed by ic_devdata)
o move ani state flags to private channel state
o remove country codes; use net80211 definitions instead
o remove GSM regulatory support; it's no longer needed now that we
pass in channel lists from above
o consolidate ADHOC_NO_11A attribute with DISALLOW_ADHOC_11A
o simplify initial channel list construction based on the EEPROM contents;
we preserve country code support for now but may want to just fallback
to a WWR sku and dispatch the discovered country code up to user space
so the channel list can be constructed using the master regdomain tables
o defer to net80211 for max antenna gain
o eliminate sorting of internal channel table; now that we use ic_devdata
as an index, table lookups are O(1)
o remove internal copy of the country code; the public one is sufficient
o remove AH_SUPPORT_11D conditional compilation; we always support 11d
o remove ath_hal_ispublicsafetysku; not needed any more
o remove ath_hal_isgsmsku; no more GSM stuff
o move Conformance Test Limit (CTL) state from private channel to a lookup
using per-band pointers cached in the private state block
o remove regulatory class id support; was unused and belongs in net80211
o fix channel list construction to set IEEE80211_CHAN_NOADHOC,
IEEE80211_CHAN_NOHOSTAP, and IEEE80211_CHAN_4MSXMIT
o remove private channel flags CHANNEL_DFS and CHANNEL_4MS_LIMIT; these are
now set in the constructed net80211 channel
o store CHANNEL_NFCREQUIRED (Noise Floor Required) channel attribute in one
of the driver-private flag bits of the net80211 channel
o move 900MHz frequency mapping into the hal; the mapped frequency is stored
in the private channel and used throughout the hal (no more mapping in the
driver and/or net80211)
o remove ath_hal_mhz2ieee; it's no longer needed as net80211 does the
calculation and available in the net80211 channel
o change noise floor calibration logic to work with compacted private channel
table setup; this may require revisiting as we no longer can distinguish
channel attributes (e.g. 11b vs 11g vs turbo) but since the data is used
only to calculate status data we can live with it for now
o change ah_getChipPowerLimits internal method to operate on a single channel
instead of all channels in the private channel table
o add ath_hal_gethwchannel to map a net80211 channel to a h/w frequency
(always the same except for 900MHz channels)
o add HAL_EEBADREG and HAL_EEBADCC status codes to better identify regulatory
problems
o remove CTRY_DEBUG and CTRY_DEFAULT enum's; these come from net80211 now
o change ath_hal_getwirelessmodes to really return wireless modes supported
by the hardware (was previously applying regulatory constraints)
o return channel interference status with IEEE80211_CHANSTATE_CWINT (should
change to a callback so hal api's can take const pointers)
o remove some #define's no longer needed with the inclusion of
<net80211/_ieee80211.h>
Sponsored by: Carlson Wireless
