Kernel pointer values are used as opaque unique identifiers, which are then
used to reconstruct references between various providers, classes, etc., inside
libgeom from the source XML. Unfortunately, they're converted to pointer-width
integers (in the form of pointers) to do this, and 32-bit userland pointers
cannot hold sensible representations (however opaque) of 64-bit kernel pointers
on all systems.
In the case where the leading bits are zero and 32 distinct bits of pointer can
be identified, this will happen to work. On systems where the upper 32-bits of
kernel pointers are non-zero and the same for all kernel pointers, this will
result in double frees and all kinds of bizarre crashes and linkage between
objects inside libgeom.
To mitigate this problem, treat the opaque identifiers in the XML as C strings
instead, and internalize them to give unique and consistent per-object pointer
values in userland for each identifier in the XML. This allows us to keep the
libgeom logic the same with only minor changes to initial setup and parsing.
It might be more sensible for speed reasons to treat the identifiers as numbers
of a large size (uintmax_t, say) rather than strings, but strings seem fine for
now.
(As an added side-effect, this makes it slightly easier to identify unresolved
references, but nothing has been added to inform the user of those.)
This makes our naming scheme more closely match other systems and the
expectations of much third-party software. MIPS builds which are little-endian
should require and exhibit no changes. Big-endian TARGET_ARCHes must be
changed:
From: To:
mipseb mips
mipsn32eb mipsn32
mips64eb mips64
An entry has been added to UPDATING and some foot-shooting protection (complete
with warnings which should become errors in the near future) to the top-level
base system Makefile.
While we have a snapshot vnode unlocked to avoid a deadlock with another
inode in the same inode block being updated, the filesystem containing
it may be forcibly unmounted. When that happens the snapshot vnode is
revoked. We need to check for that condition and fail appropriately.
This change will be included along with 232351 when it is MFC'ed to 9.
Spotted by: kib
Reviewed by: kib
New kernel events can be added at various location for sampling or counting.
This will for example allow easy system profiling whatever the processor is
with known tools like pmcstat(8).
Simultaneous usage of software PMC and hardware PMC is possible, for example
looking at the lock acquire failure, page fault while sampling on
instructions.
Sponsored by: NETASQ
MFC after: 1 month
to enable the collection of counts of synchronous and asynchronous
reads and writes for its associated filesystem. The counts are
displayed using `mount -v'.
Ensure that buffers used for paging indicate the vnode from
which they are operating so that counts of paging I/O operations
from the filesystem are collected.
This checkin only adds the setting of the mount point for the
UFS/FFS filesystem, but it would be trivial to add the setting
and clearing of the mount point at filesystem mount/unmount
time for other filesystems too.
Reviewed by: kib
are are not mapped during ranged operations and reduce the scope of the
tlbie lock only to the actual tlbie instruction instead of the entire
sequence. There are a few more optimization possibilities here as well.
Revert r233555 and apply a fix for the reference counting regressions.
Tested by: andreast, lme, nwhitehorn,
Sevan / Venture37 (venture37 at gmail dot com)
Submitted by: Robert Moore (robert dot moore at intel dot com)
In case of multiple level of inlining all the locations are flattened.
Require recent binutils/addr2line (head works or binutils from ports
with the right $PATH order).
- Multiple fixes in the calltree output (recursion case, ...)
- Fix the calltree top view that previously hide some shared nodes.
Tested with Kcachegrind(kdesdk4)/qcachegrind(head).
Sponsored by: NETASQ
violation should be activated unless the system is cold-booted
after updating EEPROM.
The PCI protocol violation happens only when established link is
10Mbps so the workaround should be updated whenever link state
change is detected. Previously the workaround was activated only
when user checks current media status with ifconfig(8).
whether the checksum of EEPROM is valid or not. Because driver
heavily relies on EEPROM information when it selectively enables
features/workarounds, it would be helpful to know whether driver
sees valid EEPROM.
While I'm here remove all other EEPROM accesses since the entire
EEPROM is loaded at device attach time.
MFC after: 2 weeks
for 82550C. For 82550 controllers this change restores CPUSaver
microcode loading. Due to silicon bug on 82550 and 82550C with
server extension, these controllers seem to require CPUSaver
microcode to receive fragmented UDP datagrams. However the
microcode shouldn't be used on client featured 82550C as it locks
up the controller. In addition, client featured 82550C does not
have the silicon bug. Also clear temporary memory used for
microcode loading since the same memory area is used for other
commands.
While I'm here use 82550C in probe message instead of generic
82550.
Reported by: Andreas Longwitz <longwitz <> incore de>
Tested by: Andreas Longwitz <longwitz <> incore de>
MFC after: 2 weeks
- Make INITAFTERSUSPEND flag independent of HOOKRESUME flag.
- Automatically set INITAFTERSUSPEND flag when ALPS GlidePoint is detected.
- Always probe Synaptics Touchpad. Allow MOUSE_SYN_GETHWINFO ioctl and
automatically set INITAFTERSUSPEND flag when a supported device is detected,
regardless of "hw.psm.synaptics_support" tunable setting.
- Update psm(4) to reflect the above changes.
- Remove long-time defunct SYNCHACK flag while I am in the neighborhood.
MFC after: 1 month
The 'make depend' rules have to use custom -I paths for the special compat
includes for the opensolaris/zfs headers.
This option will pull in the couple of files that are shared with dtrace,
but they appear to correctly use the MODULE_VERSION/MODULE_DEPEND rules
so loader should do the right thing, as should kldload.
Reviewed by: pjd (glanced at)
- Do not cover error returned by pmc_core_initialize with the
result of pmc_uncore_initialize, fail right away.
- Give a user something to report instead failing silently
Reported by: Alexandr Kovalenko <never@nevermind.kiev.ua>
The on-chip SD slots do not have PCI BARs corresponding to them, so
this has to be handled in the custom SoC memory allocation.
Provide memory resource for rids corresponding to BAR 0 and 1 in
the custom allocation code.
The XLP on-chip devices have PCI configuration headers, but some of the
devices need custom resource allocation code.
- devices with no MEM/IO BARs with registers in PCIe extended reg
space have to be handled in memory resource allocation
- devices without INTPIN/INTLINE in PCI header can be supported
by having these faked with a shadow register.
- Some devices does not allow 8/16 bit access to the register space,
he default bus space cannot be used for these.
Subclass pci and override attach and resource allocation methods to
take care of this.
Remove earlier code which did this partially.