bge_newbuf_std still has a bug for handling dma map load failure
under high network load. Just reusing mbuf is not enough as driver
already unloaded the dma map of the mbuf. Graceful recovery needs
more work.
Ideally we can just update dma address part of a Rx descriptor
because the controller never overwrite the Rx descriptor. This
requires some Rx initialization code changes and it would be done
later after fixing other incorrect bus_dma(9) usages.
- VBE 3.0 says palette format resets to 6-bit mode when video mode changes.
We simply set 8-bit mode when we switch modes if the adapter supports it.
- VBE 3.0 also says if the mode is not VGA compatible, we must use VBE
function to save/restore palette. Otherwise, VGA function may be used.
Thus, reinstate the save/load palette functions only for non-VGA compatible
modes regardless of its palette format.
- Let vesa(4) set VESA modes even if vga(4) claims to support it.
- Reset default palette if VESA pixel mode is set initially.
- Fix more style nits.
- Tear down the interrupt handler before killing the worker thread.
- Do geom withering as GEOM event to avoid acquiring the GEOM topology
lock under Giant.
PR: kern/104079
Reviewed by: joerg
Approved by: trasz (mentor)
- Rework timeout handling, to make it more graceful for devices sharing
controller port (with PMP). Wait for other commands completion/timeout
before initiating recovery.
- Handle timeouts and fatal errors with port hard-reset. The rest of
recovery will be done by XPT on receiving async event. More gracefull
per-device soft-reset recovery can be implemented later.
- Handle timeouts and fatal errors with port hard-reset. The rest of
recovery will be done by XPT on receiving async event. More gracefull
per-device soft-reset recovery can be implemented later.
- Add workaround for ATI SB600/SB700 PMP probe related bug, to speedup boot.
Most of the pieces came from Marius- correct settings for channels
and resource management. The one piece missing was that you cannot
for SBus cards replace 32 bit operations with A64 operations- not
supported.
Submitted by: marius
MFC after: 3 days
reacquiring driver lock in Rx handler. re(4) drops a driver lock
before passing received frame to upper stack and reacquire the
lock. During the time window ioctl calls could be executed and if
the ioctl was interface down request, driver will stop the
controller and free allocated mbufs. After that when driver comes
back to Rx handler again it does not know what was happend so it
could access free mbufs which in turn cause panic.
Reported by: Norbert Papke < npapk <> acm dot org >
Tested by: Norbert Papke < npapk <> acm dot org >
- Don't write actual length if the actual length pointer is NULL [2]
- correct Linux Compatibility error codes for short isochronous IN transfers
and make status field signed.
Submitted by: Leunam Elebek [1], Manuel Gebele [2]
do support 64bit addresses, the current SCRIPTS code supports only 32bit
addresses causing data corruption for buffer addresses >4GB. This problem
affects 64bit machines with more than 4GB RAM or amd64 with 4GB and
memory hole remapping.
Work-around this problem with a bus_dma tag that requests bounce-buffers
for addresses >4GB. This causes some overhead, but given the maximum SCSI
bus speed of 160MB/s compared, the effect should hardly be noticeable.
The problem was reported by Mike Watters (mike at mwatters net) who also
verified that this fix cures the problem.
Since this change is a NOOP on systems with less than 4GB RAM and fixes
data corruption (in RAM and on disk) on systems with more than 4GB, I hope
that this change is accepted for 8.0.
MFC after: 3 days (pending approval)
- Remove most of direct relations between ATA(4) peripherial and controller
levels. It makes logic more transparent and is a mandatory step to wrap
ATA(4) controller level into ATA-native CAM SIM.
- Tune AHCI and SATA2 SiI drivers memory allocation a bit to allow bigger
I/O transaction sizes without additional cost.
- Don't bother to assign vb until we know we have enough space
- Add variables for sx2, sy2, dx2, dy2 so that these aren't
calculated over and over, also reduce chance of errors.
- Use switch to assign color/format
MFC after: 3 days
- We don't need to check malloc return values with M_WAITOK
- remove variables that we don't really need
- cleanup the error paths by just calling drm_sg_cleanup()
- fix drm_sg_cleanup() to be safe to call at any time
MFC after: 2 weeks
obsoleted in 1996 by ATA-2, and crashes some modern hardware like some
revisions of the Serverworks K2 SATA controller. Even very ancient
hardware seems not to require it. In the unlikely event this causes
problems, the previous behavior can be re-enabled by defining
ATA_LEGACY_SUPPORT at the top of this file.
Reviewed by: Alexander Motin <mav@freebsd.org>
* iwnfw has now been split into individual modules so autoloading of
firmware module(s) does work again.
* Changes have been made to RUN -> AUTH transition, this should fix the
issue reported by Glen and others.
* Brandon reported issues in iwn_cmd() with large commands, those have
been fixed to.
* DEAUTH is now handled correctly.
Submitted by: Bernhard Schmidt <bschmidt at techwires.net>
Have the early USB takeover enabled for i386 and amd64
by default.
This also avoids a panic on PowerPC where the resource
isn't released properly and we find a busy resource
when the USB host controller wants to allocate it...
function may not work properly if we don't. Turn off hardware cursor as
vesa_set_mode() does.
- Add VBE 3.0 specific fields in VESA mode structure and pack it. Note
the padding is 190 bytes although VBE 3.0 says 189 bytes. It must be wrong
because the size of structure becomes 255 bytes and the specification says
it must be 256 bytes in total. In fact, an example code in the spec. does
it right, though. While we are at it, fix some i386-isms.
- Remove state buffer size limitation. It is no longer necessary since
sys/compat/x86bios/x86bios.c r198251.
- Move int 0x10 vector test into vesa_bios_post() as we always do it anyway.
splitting in bce(4) instead of (ab)using ZERO_COPY_SOCKETS that was not
propagated into if_bce.c anyway. It is disabled by default.
Approved by: davidch
MFC after: 3 days
On error, freeze device queue, to allow periph driver to do proper recovery.
Freeze SIM queue only in some cases, when it is needed to protect SIM.
Implement better command timeout detection logic for non-queued commands.
This fixes false positives when command with short timeout waiting for the
long one. For example, when hald tastes CD during burning process.
Read and clear SERR register on interrupt.
instead of POSTREAD: the hardware do not touch this memory (CPU
updates it). It is already synchronized as PREWRITE after the
processing is done.
- Synchronize RX return ring memory in rx_eof. This is needed
as the deviced updates this memory when receives packets.
- Decouple the synchronization of BGE status block in the interrupt
service routine: perfrom PREREAD synchronization only all accesses
to this block are finished. This seems to be more natural.
Reviewed by: yongari, marius
MFC after: 2 weeks
has been yanked, this works around a cam recounting bug when
CAM_DEV_UNCONFIGURED is set late in the detach. In certain conditions the
reference to the XPT device would not be released which would cause the usb
explore thread to sleep forever on "simfree", preventing any new usb devices to
be found/ejected on the bus.
This is intended to be a quick workaround to the problem without touching CAM
so it can be merged to 8.0.
Suggested by: mav
MFC after: 3 days
by checking PCI config space when the NIC is not
transmitting. Previously, a h/w fault would not have been
detected if the NIC was down, or handling an RX only
workload.
the race where interrupt thread can complete the request for which
timeout has fired and while mpt_timeout has blocked on mpt_lock.
Do a best effort to keep 4.x ang Giant-locked configurartions
compiling still.
Reported by: ups
Reviewed by: scottl
- Do not map entire real mode memory (1MB). Instead, we map IVT/BDA and
ROM area separately. Most notably, ROM area is mapped as device memory
(uncacheable) as it should be. User memory is dynamically allocated and
free'ed with contigmalloc(9) and contigfree(9). Remove now redundant and
potentially dangerous x86bios_alloc.c. If this emulator ever grows to
support non-PC hardware, we may implement it with rman(9) later.
- Move all host-specific initializations from x86emu_util.c to x86bios.c and
remove now unnecessary x86emu_util.c. Currently, non-PC hardware is not
supported. We may use bus_space(9) later when the KPI is fixed.
- Replace all bzero() calls for emulated registers with more obviously named
x86bios_init_regs(). This function also initializes DS and SS properly.
- Add x86bios_get_intr(). This function checks if the interrupt vector is
available for the platform. It is not necessary for PC-compatible hardware
but it may be needed later. ;-)
- Do not try turning off monitor if DPMS does not support the state.
- Allocate stable memory for VESA OEM strings instead of just holding
pointers to them. They may or may not be accessible always. Fix a memory
leak of video mode table while I am here.
- Add (experimental) BIOS POST call for vesa(4). This function calls VGA
BIOS POST code from the current VGA option ROM. Some video controllers
cannot save and restore the state properly even if it is claimed to be
supported. Usually the symptom is blank display after resuming from suspend
state. If the video mode does not match the previous mode after restoring,
we try BIOS POST and force the known good initial state. Some magic was
taken from NetBSD (and it was taken from vbetool, I believe.)
- Add a loader tunable for vgapci(4) to give a hint to dpms(4) and vesa(4)
to identify who owns the VESA BIOS. This is very useful for multi-display
adapter setup. By default, the POST video controller is automatically
probed and the tunable "hw.pci.default_vgapci_unit" is set to corresponding
vgapci unit number. You may override it from loader but it is very unlikely
to be necessary. Unfortunately only AGP/PCI/PCI-E controllers can be
matched because ISA controller does not have necessary device IDs.
- Fix a long standing bug in state save/restore function. The state buffer
pointer should be ES:BX, not ES:DI according to VBE 3.0. If it ever worked,
that's because BX was always zero. :-)
- Clean up register initializations more clearer per VBE 3.0.
- Fix a lot of style issues with vesa(4).
was major changes to initialize RF chipset and set H/W registers and
removed a lot of magic numbers on code. Details are as follows:
- uses the endpoint 0x89 to get TX status information which used to
get TX complete or retry numbers or get a beacon interrupt. It's
only valuable for RTL8187B.
- removes urtw_write[8|16|32]_i functions that it's useless now.
- uses ic->ic_updateslot to set SLOT, SIFS, DIES, EIFS, CW_VAL
registers that doesn't set these whenever the channel is changed.
- code for initializing RF chipset for RTL8187B changed a lot that
there was many problems on TX transfers so it doesn't work properly
even if just for a ping/pong. Now it becomes more stable than
before that TX throughputs using netperf(1) were about 15 ~ 17Mbps/s
though sometimes it encounters packet losses.
- removes a lot of magic numbers that in the previous all of
representing RX and TX descriptors were consisted of magic numbers
and structures. It'd be more readable rather than before.
- calculates TX duration more accurately for urtw(4) devices.
- style(9)
all host controllers at the same time, we avoid problems where the BIOS will
actually write to the USB registers of all the USB host controllers every time
we handover one of them, and consequently reset the OS programmed values.
Submitted by: avg
Reviewed by: jhb
to the lock we hold, disable interrupts, and announce to the firmware
that we are shutting down. Especially do this before disabling blocks.
This makes some types of machines with asf enabled no longer hang upon
boot, when we start configuring the interface.
PR: i386/96382, kern/100410, kern/122252, kern/116328
Reported by: erwin
Hardware provided by: TDC A/S
Reviewed by: stas
Tested by: stas
Sun Type 6 USB keyboard support added in rev 1.46 conflicted with
some scan codes used in Japanese keyboards because the scan code
conversion routine was ambiguous for the overlapped codes.
PR: ports/134005
Submitted by: YAMASHIRO Jun
This is needed by the upcoming AR9285 support.
Information on the layout gathered from Linux ath9k.
Not yet connected to the build.
Tested by: Eugeny Dzhurinsky
BGE_PCI_PRODID_ASICREV register to store the chip identifier and its revision.
- Add new grouping macro for 7575+ chips (BGE_IS_5755_PLUS).
- Add IDs for Fujitsu-branded Broadcom adapters.
PR: kern/127587
Tested by: Thomas Quinot <thomas@quinot.org> (BCM7561 A0)
MFC after: 2 weeks
Obtained from: OpenBSD
- support for the new Gen-2, BT, and LP-CR cards.
- T3 firmware 7.7.0
- shared "common code" updates.
Approved by: gnn (mentor)
Obtained from: Chelsio
MFC after: 1 month
and progif is evil. It doesn't work reliably[1] and we should honor BIOS
configuration by the user.
- If the SATA controller is enbled but combined mode is disabled, mask off
the emulated IDE channel on the legacy IDE controller.
Pointed out by: mav[1]
interface is fairly simple WRT dealing with flow control, but
needed 2 new RX buffer functions with "get-char-from-buf" separated
from "advance-buf-pointer" so that the pointer could be advanced
only when ttydisc_rint() succeeded.
MFC after: 1 week
The EHCI HW can use the qtd_next field instead of qtd_altnext when a short
packet is received. This contradicts what is stated in the EHCI datasheet.
Also the total-bytes field in the status field of the following TD gets
corrupted upon reception of a short packet! We work this around in software by
not queueing more than one job/TD at a time of up to 16Kbytes! The bug has been
seen on multiple INTEL based EHCI chips. Other vendors have not been tested
yet.
- Applications using /dev/usb/X.Y.Z, where Z is non-zero are affected, but not
applications using LibUSB v0.1, v1.2 and v2.0.
- Mass Storage (umass) is affected.
Submitted by: Hans Petter Selasky
MFC after: 3 days
Also, the previous commit to sys/dev/if_ndis/if_ndis.c also included the
removal of a call to ndis_setstate_80211 that is no longer needed.
Submitted by: sam
MFC after: 3 days
sysctl lock. The 'video' lock now protects the 'bus' of video output
devices attached to a graphics adapter. It is used when iterating over
the list of outputs, etc. The 'video_output' lock is used to lock the
output-specific data similar to a driver lock for the individual video
outputs.
MFC after: 2 weeks
1) Restore the PCI Express control register after a watchdog
reset. This is required because the device will come out
of watchdog reset with the pectl reg at its default state,
and important BIOS configuration (like max payload size)
could be lost.
2) Call mxge_start_locked() for every tx queue before dropping
the lock in the watchdog handler. This is required, as
the queue's buf ring may have filled during the reset.
perform 802.11 operations directly on the ndis0 interface before the
first VAP (wlan0) had been created. This would lead to a NULL-pointer
dereference in the kernel.
Submitted by: Paul B. Mahol <onemda@gmail.com>
MFC after: 3 days
capability to mii(4). Even though AR8132 uses the same model/
revision number of F1 gigabit PHY, the PHY has no ability to
establish 1000baseT link. I have no idea why Atheros use the same
device/model id for this PHY.
With this change atphy(4) does not report 1000baseT media
capability and manual 1000baseT configuration is also disabled
which is more desirable behavior for 10/100Mbps PHY.
Unlike most other PHYs there is no easy way to know which media
type the PHY supports on Marvell PHYs. MIIF_HAVEFIBER flags is now
passed via bus-specific instance variable of a device. While I'm
here add 88E1112 specific work around to set SIGDET polarity low.
Many thanks "Eugene Perevyazko <john <> dnepro dot net>" who kindly
gave remote access to system with DGE-560SX.
offloading. Datasheet said nothing about the limitation of 82559ER
except WOL. Explicitly disable Rx checksum offloading for
controllers that is known to lack the capability.
PR: kern/138135
Tested by: Gooderum, Mark < mgooderum <> websense dot com >
- Add quirk for ATI SB600 and SB700 to free SMB controller
- Correct schedule sleep time to 10us on the VIA ehci controller
Reported by: Dorian B<FC>ttner, Andriy Gapon
Submitted by: Hans Petter Selasky
- clean up USB detach logic. There seems to be some problems detaching multiple
USB HUBs connected in series from the root.
- after this patch the rule is:
1) Always use device_detach() on the USB HUB first.
2) Never just device_delete_child() on the USB HUB, because that function
will traverse to all the device leaves and free them first, and then the USB
stack will free the devices twice which doesn't work very well.
- make sure the did DMA delay gets set after the timeout has elapsed to make
logic more clear. There is no functional difference.
Submitted by: Hans Petter Selasky
Right now if applications want to use the mouse on the command line,
they use sysmouse(4) and install a signal handler in the kernel to
deliver signals when mouse events arrive. This conflicts with my plan to
change to TERM=xterm, so implement proper VT200-style mouse input.
Because mouse input is now streamed through the TTY, it means you can
now SSH to another system on the console and use the mouse there as
well. The disadvantage of the VT200 mouse protocol, is that it doesn't
seem to generate events when moving the cursor. Only when pressing and
releasing mouse buttons.
There are different protocols as well, but this one seems to be most
commonly supported.
Reported by: Paul B. Mahol <onemda gmail com>
Tested with: vim(1)
It is quite inconvenient that if an application for xterm uses 256 color
mode, text suddenly starts to blink (because of ;5; in the middle).
We'd better just implement 256 color mode and add a conversion routine
from 256 to 8 color mode, which doesn't seem to be too bad in practice.
Remapping colors is done quite simple. If one of the channels is most
actively represented, primary colors are used. If two channels are most
actively represented, secondary colors are used. If all three channels
are equal (gray), it picks between black and white.
Reported by: Paul B. Mahol <onemda gmail com>
devices that we also support, just not by default (thus only LINT or
module builds by default).
While currently there is only "/dev/full" [2], we are planning to see more
in the future. We may decide to change the module/dependency logic in the
future should the list grow too long.
This is not part of linux.ko as also non-linux binaries like kFreeBSD
userland or ports can make use of this as well.
Suggested by: rwatson [1] (name)
Submitted by: ed [2]
Discussed with: markm, ed, rwatson, kib (weeks ago)
Reviewed by: rwatson, brueffer (prev. version)
PR: kern/68961
MFC after: 6 weeks
- Clear all registers before calling real mode interrupt handlers as we did
for dpms and vesa and re-enable the function as it should be fixed by this.
- Tidy up register access. For example, when we call INT 0x15, AH=0xc0,
we used to initialize AX=0xc000 to clear AL at the same time but it is
very confusing. We don't have to do this any more because we are explicitly
clearing all registers now.
- Check size of system configuration table although it is almost always 8.
This is to make sure we are not reading some random low physical memory.
Hopefully it is just zero in that case. :-)
- Fix some style nits and add more comments.
Submitted by: paradox (ddkprog yahoo com)[1]
memory to support them. Some adapters have expansible memory slots but
video mode table is static. In this case, unusable modes may be reported.
Submitted by: paradox (ddkprog yahoo com) (initial patch)
Also align setup descriptor on 32 bytes boundary. Tx buffer have no
alignment limitation so create dmamap without alignment
restriction[1]. Rx buffer still seems to require 4 bytes alignment
limitation but we can simply use MCLBYTES for size to map the
buffer instead of TULIP_DATA_PER_DESC as the buffer is allocated
with m_getcl(9).
de(4) supports up to TULIP_MAX_TXSEG segments for Tx buffers,
increase maximum dma segment size to TULIP_MAX_TXSEG * MCLBYTES.
While I'm here remove TULIP_DATA_PER_DESC as it is not used anymore.
This should fix de(4) breakage introduced after r176206.
Submitted by: jhb [1]
Reported by: WATANABE Kazuhiro < CQG00620 <> nifty dot ne dot jp >
Tested by: WATANABE Kazuhiro < CQG00620 <> nifty dot ne dot jp >,
Takahashi Yoshihiro < nyan <> jp dot freebsd dot org >
o introduce PCIE_REGMAX and use it instead of ad-hoc constant
o where 'reg' parameter/variable is not already unsigned, cast it to
unsigned before comparison with maximum value to cut off negative
values
o use PCI_SLOTMAX in several places where 31 or 32 were explicitly used
o drop redundant check of 'bytes' in i386 pciereg_cfgread() - valid
values are already checked in the subsequent switch
Reviewed by: jhb
MFC after: 1 week
save/clear/restore flags but emulated flags have no effect on the host.
I believe BIOS writers never meant to run their code in emulated
environment with interrupt enabled. :-)
- Use memcpy(3) instead of copying individual members. I believe struct
x86regs was intentionally copied from the first half of struct x86emu_regs
for this very purpose.
- Fix some style nits and consistencies.
Reviewed by: delphij, paradox (ddkprog yahoo com)
startup and genericize it so it can be reused to map other tables as well:
- Add a routine to walk a list of ACPI subtables such as those used in the
APIC and SRAT tables in the MI acpi(4) driver.
- Move the routines for mapping and unmapping an ACPI table as well as
mapping the RSDT or XSDT and searching for a table with a given signature
out into acpica_machdep.c for both amd64 and i386.
than references to objects. In that case, simply use the Package directly.
I think a recent change to ACPI-CA is causing the interpreter to
automatically expand these references.
Reported by: Olivier Smedts olivier gid0 org
MFC after: 3 days
decoding "took". Other OS's that I checked do not do this and it breaks
some amdpm(4) devices. Prior to 7.2 we did not honor the error returned
when this failed anyway, so this in effect restores previous behavior.
PR: kern/137668
Tested by: Aurelien Mere aurelien.mere amc-os.com
MFC after: 3 days
the work area was totally unsynchronized which means this driver only
had a chance of working on x86 when no bounce buffers were involved,
which isn't that likely given that support for 64-bit DMA is currently
broken throughout ata(4).
- Add necessary little-endian conversion of accesses to the work area,
making this driver work on big-endian hosts. While at it, use the
alignment-agnostic byte order encoders in order to be on the safe side.
- Clear the reserved member of the SG list entries in order to be on the
safe side. [1]
Submitted by: yongari [1]
Reviewed by: yongari
MFC after: 3 days
30-bit like the reset of the controllers supported by this driver.
Actually ALi M5451 can be setup up to generate 32-bit addresses by
setting the 31st bit via the accompanying ISA bridge, which allows
it to work in sparc64 machines whose IOMMU require at least 32-bit
DMA. Even though other architectures would also benefit from 32-bit
DMA, enabling this bit is limited to sparc64 as bus_dma(9) doesn't
generally guarantee that a low address of BUS_SPACE_MAXADDR_32BIT
results in a buffer in the 32-bit range.
- According to Tatsuo YOKOGAWA's ali(4), the the DMA transfer size of
ALi M5451 is fixed to 64k and in fact using the default size of 4k
- The 4DWAVE DX and NX require the recording buffer to be 8-byte
aligned so adjust the bus_dma_tag_create(9) accordingly.
- Unlike the rest of the controllers supported by this driver, the
ALi M5451 only has 32 hardware channels instead of 64 so limit the
loop in tr_intr() accordingly. [1]
Submitted by: yongari [1]
Reviewed by: yongari (superset of what is committed)
MFC after: 3 days
It seems Clang breaks when checking for SPCLKEY, which is now
0x80000000. Using an unsigned integer fixes this. This is also
consistent with other pieces of kbd/syscons code, because these also use
u_int.
Submitted by: rdivacky
- Mark the link as down, so if watchdog reset fails, link watching
failover software can notice it
- Don't send MXGEFW_CMD_ETHERNET_DOWN if the NIC has been reset, it is
not needed, and will fail on a freshly reset NIC.
- Ensure the transmit routines aren't attempting to PIO write to doorbells
while the NIC is being reset.
- Download the correct f/w, rather than using the EEPROM f/w after reset.
- Export a count of the number of watchdog resets via sysctl
- Zero all f/w stats at reset. This will lead to less confusing
diagnostic output when investigating NIC failures.
MFC after: 3 days
instead of SI_SUB_KLD. Note that we don't believe that there is any
consumers of x86bios that would be triggered in the early stage of boot,
so this is more or less just a safebelt.
Submitted by: swell.k at gmail.com
x86emu to this new module.
This changeset also brings a fix for bugs introduced with the initial
x86emu commit, which prevents the user from using some display mode or
cause instant reboots during mode switch.
Submitted by: paradox <ddkprog yahoo com>
Add a maximum response length for FCP RSPNS IUs.
Clarify some of the FC option words for setting parameters
and try and disable automatic PRLI when in target mode- this
should correct some cases of N-port topologies with 23XX cards
where we put out an illegal PRLI (in target mode only we're
not supposed to put out a PRLI).
Just take keyent_t to use an u_int to store the Unicode codepoints.
Unfortunately the keymap is now too big to be loaded using an ioctl
argument, so change the ioctl to pick a pointer.
This change breaks kbdcontrol ABI. It doesn't break X11, because X11
doesn't do anything with syscons keymaps. It just switches the device
out of K_XLATE.
Obtained from: //depot/user/ed/newcons/...
This code seems to do exactly the same as ttydisc_rint_simple() does
nowadays. Just remove it.
Obtained from: //depot/user/ed/newcons/sys/dev/syscons/syscons.c
- Implement MSI support (MSIX support was already there)
- Use a table to drive MSI/MSIX exceptions
- Pre-calculate the command address instead of wasting cycles doing the
calculation on every i/o.
number of MSIX interrupts that are needed, and don't strictly check for 4.
Enable enough interrupt mask bits so that the controller will generate
interrupts in PERFORMANT mode. This fixes the hang-on-boot issues that
people were seeing with newer controllers.
we at least don't panic.
We don't really support dual role mode (INITIATOR/TARGET) any more. We
should but it's broken and will take a fair amount of effort to fix
and correctly manage both initiator and target roles sharing the port
database. So, for now, disallow it.
For some vague reason, it may be possible that scp->cursor_pos exceeds
scp->ysize * scp->xsize. This means that teken_set_cursor() may get
called with an invalid position. Just ignore the old cursor position in
this case.
Reported by: Paul B. Mahol <onemda gmail com>
MFC after: 1 month
- Improve newer AMD processor support (Family 0Fh Revision F and later).
- Adjust offset if DiodeOffet is set and valid. Note it is experimental
but it seems to give us more realistic temperatures. Newer Linux driver
blindly adds 21C for Family 0Fh desktop processors, however.
- Always populate dev.cpu and dev.amdtemp sysctl trees regardless of probe
order for consistency. Previously, dev.cpu.N.temperature was not populated
if amdtemp was loaded later than ACPI CPU driver and temperatures were not
accessible from dev.amdtemp.N.sensor0 tree for Family 10h/11h processors.
- Read the CPUID from PCI register instead of CPUID instruction to prevent
possible revision mismatches on multi-socket system.
- Change macros and variables to make them closer to AMD documents.
- Fix style(9) nits and improve comments.
Different sub-kinds of PCI buses may have different rules and
thus it is up for the bus backends to do proper input checks.
For example, PCIe allows configuration register numbers < 0x1000,
while for PCI proper the limit is 0x100.
And, in fact, the buses already do the checks.
Reviewed by: jhb
MFC after: 1 week
X-ToDo: add check for negative value to bus backends
X-ToDo: use named constant for maximum PCIe register
"set vesa mode" and higher 16bits of the flag would be the desired mode.
One can now set, for instance, hint.sc.0.flags=0x01680180, which means
that the system should set VESA mode 0x168 upon boot.
Submitted by: paradox <ddkprog yahoo com>, swell k at gmail.com with
some minor changes.
| grep <modname>' can be used instead.
Put a message behind bootverbose as
ichwd0: <Intel ICH6M watchdog timer> on isa0
ichwd0: Intel ICH6M watchdog timer (ICH6 or equivalent)
does not make a lot of sense.
MFC after: 1 week
where we figure out the hostname length under the lock, malloc the buffer
with the lock dropped, then recheck the length under the lock and loop again
if the buffer is now too small.
Tested by: Norbert Koch nkoch demig de
MFC after: 3 days
- Add vesa kernel options for amd64.
- Connect libvgl library and splash kernel modules to amd64 build.
- Connect manual page dpms(4) to amd64 build.
- Remove old vesa/dpms files.
Submitted by: paradox <ddkprog yahoo com> [1], swell k at gmail.com
(with some minor tweaks)
them from the old place. This commit necessary so that the tree would not
enter a broken state.
sys/i386/isa/vesa.c -> dev/fb/vesa.c
sys/i386/include/pc/vesa.h -> dev/fb/vesa.h
sys/i386/isa/dpms.c -> dev/dpms/dpms.c
"COMMAND 0x........ TIMEOUT AFTER .. SECONDS" messages. Any commands
that get truly stuck will still trigger the warning and the hardware
health check, just a little bit later.
# My reading of the docs suggests this can only happen on 10Base5 and
# 10Base2 setups (and maybe only the former), which I can't test
# adequately since I have nothing but 10BaseT, etc here.
requirements. It is busdma task, to manage proper alignment by loading
data to bounce buffers.
PR: kern/127316
Reviewed by: current@
Tested by: Ryan Rogers
Now that pty(4) is a loadable kernel module, I'd better move /dev/ptmx
in there as well. This means that pty(4) now provides almost all
pseudo-terminal compatibility code. This means it's very easy to test
whether applications use the proper library interfaces when allocating
pseudo-terminals (namely posix_openpt and openpty).
sure when this became necessary and might be caused by some missing
code to do auto-configuration of DWDS usage
Noticed by: Felix Feng <unixwind@gmail.com>
