This patch adds missing hints for ath0 (eepromaddr) and GPIO (mask & leds).
ath0 doesn't work without eeprom hints, so this commit should make wifi
works on Onion Omega.
GPIO mask is required if you want to use gpiobus and GPIO pins on your
board. Onion Omega has several leds connected to gpio pins (one on board,
one color on dock).
This commit adds mask for gpiobus and allow you to turn off/on leds via
/dev/leds/{board,blue,green,red} (on by default).
Tested on Onion Omega 1.
Reviewed by: adrian
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D9107
- em(4) igb(4) and lem(4)
- deprecate the igb device from kernel configurations
- create a symbolic link in /boot/kernel from if_em.ko to if_igb.ko
Devices tested:
- 82574L
- I218-LM
- 82546GB
- 82579LM
- I350
- I217
Please report problems to freebsd-net@freebsd.org
Partial review from jhb and suggestions on how to *not* brick folks who
originally would have lost their igbX device.
Submitted by: mmacy@nextbsd.org
MFC after: 2 weeks
Relnotes: yes
Sponsored by: Limelight Networks and Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D8299
Build and install an o32 set of libraries on mips64 suitable for
running o32 binaries via COMPAT_FREEBSD32. Enable COMPAT_FREEBSD32 in
MALTA64.
Reviewed by: jmallett, imp
Sponsored by: DARPA / AFRL
Differential Revision: https://reviews.freebsd.org/D9032
Recognize new MACHINE_ARCH names now as we have added hardfloat support.
Switch JZ4780 to mipselhf and remove all uses of TARGET_ARCH in kernel
.mk files.
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D8989
It is required to proceed full cache flush before we can use wait
instruction on multicore, so use nop instead for now.
Submitted by: kan
Sponsored by: DARPA, AFRL
X1000 systems on chips.
Imgtec CI20 and Ingenic CANNA boards supported.
Submitted by: Alexander Kabaev <kan@FreeBSD.org>
Reviewed by: Ruslan Bukin <br@FreeBSD.org>
Sponsored by: DARPA, AFRL
All devices:
- add support for rate adaptation via ieee80211_amrr(9);
- use short preamble for transmitted frames when needed;
- multi-bss support:
* for RTL8821AU: 2 VAPs at the same time;
* other: 1 any VAP + 1 sta VAP.
RTL8188CE:
- fix IQ calibration bug (reason of significant speed degradation);
- add h/w crypto acceleration support.
USB:
- A-MPDU Tx support;
- short GI support;
Other:
- add support for RTL8812AU / RTL8821AU chipsets
(a/b/g/n only; no ac yet);
- split merged code into subparts:
* bus glue (usb/*, pci/*, rtl*/usb/*, rtl*/pci/*)
* common (if_rtwn*)
* chip-specific (rtl*/*)
- various other bugfixes.
Due to code reorganization, module names / requirements were changed too:
urtwn urtwnfw -> rtwn rtwn_usb rtwnfw
rtwn rtwnfw -> rtwn rtwn_pci rtwnfw
Tested with RTL8188CE, RTL8188CUS, RTL8188EU and RTL8821AU.
Tested by: kevlo, garga,
Peter Garshtja <peter.garshtja@ambient-md.com>,
Kevin McAleavey <kevin.mcaleavey@knosproject.com>,
Ilias-Dimitrios Vrachnis <id@vrachnis.com>,
<otacilio.neto@bsd.com.br>
Relnotes: yes
As of r302092, pipe is a wrapper around pipe2 and the pipe syscall is no
longer used. It is included only with the COMPAT_FREEBSD10 kernel option.
Add the compat option to support upgrades from systems with an earlier
userland.
MFC after: 1 week
to add actions that run when a TCP frame is sent or received on a TCP
session in the ESTABLISHED state. In the base tree, this functionality is
only used for the h_ertt module, which is used by the cc_cdg, cc_chd, cc_hd,
and cc_vegas congestion control modules.
Presently, we incur overhead to check for hooks each time a TCP frame is
sent or received on an ESTABLISHED TCP session.
This change adds a new compile-time option (TCP_HHOOK) to determine whether
to include the hhook(9) framework for TCP. To retain backwards
compatibility, I added the TCP_HHOOK option to every configuration file that
already defined "options INET". (Therefore, this patch introduces no
functional change. In order to see a functional difference, you need to
compile a custom kernel without the TCP_HHOOK option.) This change will
allow users to easily exclude this functionality from their kernel, should
they wish to do so.
Note that any users who use a custom kernel configuration and use one of the
congestion control modules listed above will need to add the TCP_HHOOK
option to their kernel configuration.
Reviewed by: rrs, lstewart, hiren (previous version), sjg (makefiles only)
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D8185
This patch adds driver implementation for BHND USB core. Driver has been
imported from ZRouter project with small adaptions for FreeBSD 11.
Also it's enabled for BroadCom MIPS74k boards by default. It's fully tested
on Asus boards (RT-N16: external USB, RT-N53: USB bus between SoC and WiFi
chips).
Reviewed by: adrian (mentor), ray
Approved by: adrian (mentor)
Obtained from: ZRouter
Differential Revision: https://reviews.freebsd.org/D7781
This adds support for EARLY_PRINTF via the CFE console; the aim is to
provide a fix for the otherwise cyclic dependency between PMU discovery
and console printf/DELAY:
- We need to parse the bhnd(4) core table to determine the address (and
type) of the PMU/PLL registers and calculate the CPU clock frequency.
- The core table parsing code will emit a printf() if a parse error is
hit.
- Safely calling printf() without EARLY_PRINTF requires a working
DELAY+cninit, which means we need the PMU.
Errors in core table parsing shouldn't happen, but lack of EARLY_PRINTF
makes debugging more difficult.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7498
- Added a generic bhnd_nvram_parser API, with support for the TLV format
used on WGT634U devices, the standard BCM NVRAM format used on most
modern devices, and the "board text file" format used on some hardware
to supply external NVRAM data at runtime (e.g. via an EFI variable).
- Extended the bhnd_bus_if and bhnd_nvram_if interfaces to support both
string-based and primitive data type variable access, required for
common behavior across both SPROM and NVRAM data sources.
- Extended the existing SPROM implementation to support the new
string-based NVRAM APIs.
- Added an abstract bhnd_nvram driver, implementing the bhnd_nvram_if
atop the bhnd_nvram_parser API.
- Added a CFE-based bhnd_nvram driver to provide read-only access to
NVRAM data on MIPS SoCs, pending implementation of a flash-aware
bhnd_nvram driver.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7489
Relying on the boot loader console configuration allows us to use a
common set of device hints for all SENTRY5 devices.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7376
The delta between SENTRY5 and BCM was already small due to BCM being
derived from SENTRY5; re-integrating the two avoids the maintenance
overhead of keeping them both in sync with bhnd(4) changes.
- Re-integrate minor SENTRY5 deltas in bcm_machdep.c
- Modify uart_cpu_chipc to allow specifying UART debug/console flags via
kenv and device hints.
- Switch SENTRY5 to std.broadcom
- Enabled CFI flash support for SENTRY5
Reviewed by: Michael Zhilin <mizkha@gmail.com> (Broadcom MIPS support)
Approved by: re (gjb), adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D6897
Now that bhnd(4) provides feature parity with the previous siba/mips
implementation, we can switch sentry5 over and begin lifting common
support code out for use across bhnd(4) embedded targets.
Changes:
- Fixed enumeration of siba(4) per-core address maps, required for
discovery of memory mapped chipc flash region on siba(4) devices.
- Simplified bhnd kernel configuration (dropped 'bhndbus' option).
- Replaced files.broadcom's direct file references with their
corresponding standard kernel options.
- Lifted out common bcma/siba nexus support, inheriting from the new
generic bhnd_nexus driver.
- Dropped now-unused sentry5 siba code.
- Re-integrated BCM into the universe build now that it actually compiles.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D6712
Etherswitch support is built by default on all SoCs except RT3662/RT3883
as they have no built-in switch and their configurations with external
switches are not yet supported.
Sponsored by: Smartcom - Bulgaria AD
Relies on BHND(4) driver.
There files contains machine-dependent code for Broadcom MIPS processor and
provide UART driver.
This is a work in progress; it and the current bhnd code is enough to boot
on the ASUS RT-N16 and RT-N53 platforms.
Submitted by: Michael Zhilin <mizhka@gmail.com>
Differential Revision: https://reviews.freebsd.org/D6251
legacy siba sentry5 cpu glue.
The siba_cc code is the hard-coded chipcommon bits for the sentry s5,
which will eventually be replaced with the more flexible bhnd sipa/cc
code.
bwn, etc uses siba_bwn, which doesn't use siba or siba_cc to do anything.
Only compile what each SoC needs and get rid of MEDIATEK generic config.
Approved by: adrian (mentor)
Sponsored by: Smartcom - Bulgaria AD
Differential Revision: https://reviews.freebsd.org/D5996
Revision 298068 changed MIPS_INTRNG and ARM_INTRNG to simply INTRNG.
MEDIATEK_BASE config was missed by this revision, so we change
MIPS_INTRNG to INTRNG here.
Approved by: adrian (mentor)
Sponsored by: Smartcom - Bulgaria AD
Differential Revision: https://reviews.freebsd.org/D5978
the following:
1. Give the appropriate board dts file to be used by either:
1.1. edit the SoC kernel config required (e.g., MT7620A_FDT) and include
the required FDT_DTS_FILE makeoption; or
1.2. simply supply FDT_DTS_FILE="xx.dts" on the command line when building
the kernel
Of course, the user can also create a completely new kernel config to
match the desired board and include the SoC kernel config from within
it.
If required, edit the MEDIATEK config file, which includes optional
drivers and comment out the unneeded ones.
2.1. this would only make sense if kernel size is a concern. Even if we
build the kernel with all drivers, if we lzma it and package it as a uImage,
its size is still around 1.1MiB.
The user will have to choose a dts file (or create a new one) from
sys/gnu/dts/mips , where all Mediatek/Ralink dts files will be imported via
a later revision.
Approved by: adrian (mentor)
Sponsored by: Smartcom - Bulgaria AD
Differential Revision: https://reviews.freebsd.org/D5966
This revision does the following renames:
CPU_MIPS24KC -> CPU_MIPS24K
CPU_MIPS74KC -> CPU_MIPS74K
CPU_MIPS1004KC -> CPU_MIPS1004K
It also adds the following new CPU_MIPSxxx options:
CPU_MIPS24KE, CPU_MIPS34K, CPU_MIPS1074K, CPU_INTERAPTIV, CPU_PROAPTIV
CPU_MIPSxxxxKC is limiting and possibly misleading as it implies the
MIPSxxxxK CPU has no FPU.
It would be better if the CPUs are named after their standard functionalities
only and the presence or absence of FPU can then be controlled via the
CPU_HAVEFPU option.
I will send out another dependent revision that moves MIPS 32 r2 and r3
CPUs to use the EHB instruction for clearing hazards instead of NOP/SSNOP.
Submitted by: Stanislav Galabov <sgalabov@gmail.com>
Reviewed by: imp
Differential Revision: https://reviews.freebsd.org/D5077
These are all works in progress. Notably - no wifi support just yet!
I've booted the MT7620 on a TP-Link Archer C2 via tftpboot.
Submitted by: Stanislav Galabov <sgalabov@gmail.com>
for the AP143.
Wifi doesn't work on the QCA9533 board, but basic ethernet/ethernet
and ethernet switch support does work.
The AP143 has 32MB RAM and 4MB flash, so this was tested with a USB
rootfs.
Tested:
* QCA9533v2, AP143 reference design board.
Small $25 IoT device, 400mhz Atheros cpu, Atheros WiFi and Ethernet
18 GPIOs, and support for Relay, Servo, and OLED expansion
https://onion.io/omega/
Reviewed by: adrian
Approved by: bapt (mentor)
Relnotes: yes
Sponsored by: ScaleEngine Inc.
Differential Revision: https://reviews.freebsd.org/D4188
This is an AR9331 part based on the AP121 reference design but with
32MB RAM. Yes, it has 4MB flash and it has no USB, so clever hacks
are required to get it up and working.
But boot/work it does.
The ERL is a fairly cheap (~$100 USD) and readily available dual core
MIPS64 device so it makes a useful MIPS reference platform.
This is based in part on the kernel config generated by the mkerlimage
script from http://rtfm.net/FreeBSD/ERL/.
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3884
* Shuffle the kernel to be at the beginning
* Give the kernel 2mb, the rootfs 6mb, and 'mib0' the rest
* put the cfg parition just before the ART calibration data for the
wifi part in the SoC
* .. and make sure ART points to the right 64k region.
I've updated the freebsd-wifi-build wiki the instructions on using this.
If someone has an AP135 with 8MB SPI flash then this won't work; everything
minus the big mib0 partition is just a bit over 8MB. Come see me if this
ever happens (you'll likely just have to shrink the rootfs and the kernel
a little in order to make it fit.)
Tested:
* AP135 reference board.
The SoC, the flash, the ethernet ports and ethernet switch all work.
The USB works.
The 11ac PCIe NIC internally is at least seen by the PCIE RC, but
I haven't tried using it yet. There's no driver and I haven't
yet swapped it out for a non-11ac chip.
The on-chip 2GHz wifi works, but there are some data errors that
get thrown up in STA mode when scanning. I have a feeling I have
to finish the DDR flush code out and have it run correctly on the
shared interrupts; that'll take a bit of time to get right.
But if you're after an updated piece of hardware, the Archer C7 v2
is certainly there, and you can replace the 11ac NIC with a 3x3
Atheros PCIe device (eg AR9380, AR9390, AR9580, etc) and it'll
"just work".
Tested:
* TP-Link archer c7v2.
The Tp-link Archer-C7v2 unit has a QCA9558 internally but hangs the
QCA988x 11ac PCIe NIC off of PCI RC #1, not #0.
So I actually finally /do/ have a board to verify whether PCIe is working.
Grr.
Tested:
* TP-Link Archer-C7v2.
* GENERAL
- Update copyright.
- Make kernel options for RANDOM_YARROW and RANDOM_DUMMY. Set
neither to ON, which means we want Fortuna
- If there is no 'device random' in the kernel, there will be NO
random(4) device in the kernel, and the KERN_ARND sysctl will
return nothing. With RANDOM_DUMMY there will be a random(4) that
always blocks.
- Repair kern.arandom (KERN_ARND sysctl). The old version went
through arc4random(9) and was a bit weird.
- Adjust arc4random stirring a bit - the existing code looks a little
suspect.
- Fix the nasty pre- and post-read overloading by providing explictit
functions to do these tasks.
- Redo read_random(9) so as to duplicate random(4)'s read internals.
This makes it a first-class citizen rather than a hack.
- Move stuff out of locked regions when it does not need to be
there.
- Trim RANDOM_DEBUG printfs. Some are excess to requirement, some
behind boot verbose.
- Use SYSINIT to sequence the startup.
- Fix init/deinit sysctl stuff.
- Make relevant sysctls also tunables.
- Add different harvesting "styles" to allow for different requirements
(direct, queue, fast).
- Add harvesting of FFS atime events. This needs to be checked for
weighing down the FS code.
- Add harvesting of slab allocator events. This needs to be checked for
weighing down the allocator code.
- Fix the random(9) manpage.
- Loadable modules are not present for now. These will be re-engineered
when the dust settles.
- Use macros for locks.
- Fix comments.
* src/share/man/...
- Update the man pages.
* src/etc/...
- The startup/shutdown work is done in D2924.
* src/UPDATING
- Add UPDATING announcement.
* src/sys/dev/random/build.sh
- Add copyright.
- Add libz for unit tests.
* src/sys/dev/random/dummy.c
- Remove; no longer needed. Functionality incorporated into randomdev.*.
* live_entropy_sources.c live_entropy_sources.h
- Remove; content moved.
- move content to randomdev.[ch] and optimise.
* src/sys/dev/random/random_adaptors.c src/sys/dev/random/random_adaptors.h
- Remove; plugability is no longer used. Compile-time algorithm
selection is the way to go.
* src/sys/dev/random/random_harvestq.c src/sys/dev/random/random_harvestq.h
- Add early (re)boot-time randomness caching.
* src/sys/dev/random/randomdev_soft.c src/sys/dev/random/randomdev_soft.h
- Remove; no longer needed.
* src/sys/dev/random/uint128.h
- Provide a fake uint128_t; if a real one ever arrived, we can use
that instead. All that is needed here is N=0, N++, N==0, and some
localised trickery is used to manufacture a 128-bit 0ULLL.
* src/sys/dev/random/unit_test.c src/sys/dev/random/unit_test.h
- Improve unit tests; previously the testing human needed clairvoyance;
now the test will do a basic check of compressibility. Clairvoyant
talent is still a good idea.
- This is still a long way off a proper unit test.
* src/sys/dev/random/fortuna.c src/sys/dev/random/fortuna.h
- Improve messy union to just uint128_t.
- Remove unneeded 'static struct fortuna_start_cache'.
- Tighten up up arithmetic.
- Provide a method to allow eternal junk to be introduced; harden
it against blatant by compress/hashing.
- Assert that locks are held correctly.
- Fix the nasty pre- and post-read overloading by providing explictit
functions to do these tasks.
- Turn into self-sufficient module (no longer requires randomdev_soft.[ch])
* src/sys/dev/random/yarrow.c src/sys/dev/random/yarrow.h
- Improve messy union to just uint128_t.
- Remove unneeded 'staic struct start_cache'.
- Tighten up up arithmetic.
- Provide a method to allow eternal junk to be introduced; harden
it against blatant by compress/hashing.
- Assert that locks are held correctly.
- Fix the nasty pre- and post-read overloading by providing explictit
functions to do these tasks.
- Turn into self-sufficient module (no longer requires randomdev_soft.[ch])
- Fix some magic numbers elsewhere used as FAST and SLOW.
Differential Revision: https://reviews.freebsd.org/D2025
Reviewed by: vsevolod,delphij,rwatson,trasz,jmg
Approved by: so (delphij)
This makes the TP-Link WDR3600 routers more useful
Differential Revision: https://reviews.freebsd.org/D2780
Approved by: adrian
Sponsored by: ScaleEngine Inc.
* Change mips24k -> mips74k for hwpmc, but leave it disabled for now.
* don't build pci by default.
* build pci and qca955x_pci for AP135, as theres a PCIe NIC.
* don't build a hwpmc module, it doesn't really work out well
for the mips boards at the moment.
* add ipfw and DEFAULT_TO_ACCEPT.
The carambola2 exposes all the gpio pins, but some are reserved for
core functions (eg usb, ethernet, etc.) Others are configured by default
to be available as normal GPIO pins to do interesting things with.
GPIO 18->23 is the I2S, SLIC and SPDIF device pins, but none of those
are currently used. So, just allow those to show up.
Tested:
* AR9344, Carambola 2
* (.. bitbang SPI to an Adafruit LCD via libgpio, because FreeBSD could
do with more shiny output devices that aren't network interfaces.)
TODO:
There are some other pins aren't currently included here, but should be.
The LED pins are for the internal switch inside the AR9344.
* GPIO 0+1 are "LED0 + LED1", but they're tied to high for bootstrapping.
* GPIO 13-17 are "LED2..7", but they're tied (H, L, L, L, H) for bootstrapping.
* GPIO 11 and 12 are UART RTS/CTS or I2S; but GPIO 12 is tied L for bootstrap.
The MAC addresses were totally wrong. They're like the DIR-625C1 - at
0x1ffe0004 and 0x1ffe0018. They're however stored as text strings.
The ath0 MAC address is also not set, even though the calibration
partition is valid.
So, pick the board address / first MAC as the ath0 MAC, and derive
arge0/arge1 from that. That way they're hopefully unique enough
for people with multiple devices.
Tested:
* DIR-655A1
TODO:
* Do the same for the DIR-625A1 and DIR-625C1.
This allows the TL-WDR3600 to use the correct MAC address for ath0, ath1
and arge0. arge1 isn't used; until I disable it entirely it'll just
show up with a randomly generated MAC.
Without this the autotuning fails for small amounts of RAM (32mb),
which all the AR91xx shipping products seemed to have.
Thanks to gjb for reminding me to re-test this stuff.
Tested:
* AR91xx, TP-Link TL-WR1043nd v1
This is based on the AP135 design - QCA9558 SoC, 3x3 2GHz wifi, but no
5GHz (11n or 11ac) chip is available.
It however still has 128MiB of RAM, 16MiB of NOR flash and the AR8327N
gigabit switch - so it's quite a beefy router device.
Tested:
* Well, a unit, naturally
Obtained from: Completely messing up an amazon.com order and getting this instead, and asking "hey, wonder if I could.."
* add ipfw
* delete ath / ath_ahb for now, until I can have Warner beat me
with the clue stick about putting in conditional build things into
the ath Makefile so the module builds can just have the HAL bits
that are relevant for a particular target.
