exhaustion is encountered. There was a fix made previously for this
problem but the solution (breaking out of the receive loop) does not
seem to work. mbuf reuse strategy is already adopted by other drivers
such as if_bge. The problem was recreated and the patch is also
verified in the same test environment.
sparc64 GENERIC and the sound device drivers known working on sparc64
to use bus_get_dma_tag() to obtain the parent DMA tag so we can get rid
of the sparc64_root_dma_tag kludge eventually. Except for ath(4), sk(4),
stge(4) and ti(4) these changes are runtime tested (unless I booted up
the wrong kernels again...).
will fix a problem where you boot w/ the default of autoselect, but then
set the speed to 100/full, the switch will keep the autoselect/100/full
negotiation... This will continue to work till someone resets the switch
or unplugs the cable resulting in the switch failing to autoneg and falling
back to 100/half, causing a hard to track down duplex mismatch..
Submitted by: nCircle Network Security, Inc.
MFC after: 1 week
ifm_status and ifm_active. IFM_10_T gets set in the ifm_active field,
not in the ifm_status field, as far as I can tell.
Note: this was to enable a workaround that's rarely enabled. I don't know
how to corrupt my eeprom to test it, and would rather not know...
rather than in ifindex_table[]; all (except one) accesses are
through ifp anyway. IF_LLADDR() works faster, and all (except
one) ifaddr_byindex() users were converted to use ifp->if_addr.
- Stop storing a (pointer to) Ethernet address in "struct arpcom",
and drop the IFP2ENADDR() macro; all users have been converted
to use IF_LLADDR() instead.
opt_device_polling.h
- Include opt_device_polling.h into appropriate files.
- Embrace with HAVE_KERNEL_OPTION_HEADERS the include in the files that
can be compiled as loadable modules.
Reviewed by: bde
o Axe poll in trap.
o Axe IFF_POLLING flag from if_flags.
o Rework revision 1.21 (Giant removal), in such a way that
poll_mtx is not dropped during call to polling handler.
This fixes problem with idle polling.
o Make registration and deregistration from polling in a
functional way, insted of next tick/interrupt.
o Obsolete kern.polling.enable. Polling is turned on/off
with ifconfig.
Detailed kern_poll.c changes:
- Remove polling handler flags, introduced in 1.21. The are not
needed now.
- Forget and do not check if_flags, if_capenable and if_drv_flags.
- Call all registered polling handlers unconditionally.
- Do not drop poll_mtx, when entering polling handlers.
- In ether_poll() NET_LOCK_GIANT prior to locking poll_mtx.
- In netisr_poll() axe the block, where polling code asks drivers
to unregister.
- In netisr_poll() and ether_poll() do polling always, if any
handlers are present.
- In ether_poll_[de]register() remove a lot of error hiding code. Assert
that arguments are correct, instead.
- In ether_poll_[de]register() use standard return values in case of
error or success.
- Introduce poll_switch() that is a sysctl handler for kern.polling.enable.
poll_switch() goes through interface list and enabled/disables polling.
A message that kern.polling.enable is deprecated is printed.
Detailed driver changes:
- On attach driver announces IFCAP_POLLING in if_capabilities, but
not in if_capenable.
- On detach driver calls ether_poll_deregister() if polling is enabled.
- In polling handler driver obtains its lock and checks IFF_DRV_RUNNING
flag. If there is no, then unlocks and returns.
- In ioctl handler driver checks for IFCAP_POLLING flag requested to
be set or cleared. Driver first calls ether_poll_[de]register(), then
obtains driver lock and [dis/en]ables interrupts.
- In interrupt handler driver checks IFCAP_POLLING flag in if_capenable.
If present, then returns.This is important to protect from spurious
interrupts.
Reviewed by: ru, sam, jhb
The FXP_SCR_FLOWCONTROL registers is at offset 0x19, but 2 bytes wide.
It cannot be read as a word without causing a panic on architectures
that enforce strict alignment.
MFC after: 3 days
that if softclock is running on another CPU and is blocked on our driver
lock, we will wait until it has acquired the lock, seen that it was
cancelled, dropped the lock, and awakened us so that we can safely destroy
the mutex.
MFC after: 3 days
IFF_DRV_RUNNING, as well as the move from ifnet.if_flags to
ifnet.if_drv_flags. Device drivers are now responsible for
synchronizing access to these flags, as they are in if_drv_flags. This
helps prevent races between the network stack and device driver in
maintaining the interface flags field.
Many __FreeBSD__ and __FreeBSD_version checks maintained and continued;
some less so.
Reviewed by: pjd, bz
MFC after: 7 days
the timeout routine.
- Fix locking in detach.
- Add locking in shutdown.
- Don't mess with the PCI command register in resume, the PCI bus driver
already does this for us.
- Add locking to the non-serial ifmedia routines.
- Fix locking in ioctl.
- Remove spls and support for 4.x.
MFC after: 1 week
over iteration of their multicast address lists when synchronizing the
hardware address filter with the network stack-maintained list.
Problem reported by: Ed Maste (emaste at phaedrus dot sandvine dot ca>
MFC after: 1 week
struct ifnet or the layer 2 common structure it was embedded in have
been replaced with a struct ifnet pointer to be filled by a call to the
new function, if_alloc(). The layer 2 common structure is also allocated
via if_alloc() based on the interface type. It is hung off the new
struct ifnet member, if_l2com.
This change removes the size of these structures from the kernel ABI and
will allow us to better manage them as interfaces come and go.
Other changes of note:
- Struct arpcom is no longer referenced in normal interface code.
Instead the Ethernet address is accessed via the IFP2ENADDR() macro.
To enforce this ac_enaddr has been renamed to _ac_enaddr.
- The second argument to ether_ifattach is now always the mac address
from driver private storage rather than sometimes being ac_enaddr.
Reviewed by: sobomax, sam
latest 82550 and 82551 chipsets (revision IDs 0x0e, 0x0f and 0x10).
We were only enabling it for revisions 0x0c and 0x0d, now it's
enabled for any 8255x NIC with a revision ID bigger than 0x0c. It
should be safe, and this is what Intel does in their open source
driver.
MFC after: 2 weeks
Tested by: Pavel Lobach lobach_pavel at mail dot ru
from an mbuf into the fxp_encap() function, as done in other drivers.
- Don't waste time calling bus_dmamap_load_mbuf() if we know the mbuf
chain is too long to fit in a TX descriptor, call m_defrag() first.
- Convert fxp(4) to use bus_dmamap_load_mbuf_sg().
a vlan interface attached to a fxp(4) card when it has not been
initialized yet. We now set the links from our internel TX descriptor
structure to the TX command blocks at attach time rather than at init
time. While I'm here, slightly improve the style in fxp_attach().
PR: kern/78112
Reported by: Gavin Atkinson <gavin.atkinson@ury.york.ac.uk> and others
Tested by: flz, Gavin Atkinson <gavin.atkinson@ury.york.ac.uk>
MFC after: 1 week
testing it to know whether we should enable the 82503 serial mode...
Move code to the right location and disallow the use of the 82503
serial mode if the sc->revision field is 0 again. This makes fxp(4)
work correctly with ATMEL 350 93C46 cards (3 port 82559 based with a
82555 PHY), as well as with the older ATMEL 220 93C46 (same flavour)
and with the even older 10Mbps-only 82557 cards with the 82503 serial
interface.
Tested by: Andre Albsmeier <andrer@albsmeier.net>, krion
MFC after: 2 weeks
interface as well. This is not an expected revision id per the
datasheet, but unfortunately there are such cards out there with
a 82557 chipset, and they want to use the 82503.
PR: kern/75739
Reported by: Andre Albsmeier <andre.albsmeier@siemens.com>
datasheet says it is only valid for such chipsets and shouldn't be used
with others. This fixes some 82559 based cards which otherwise only
work at 10Mbit.
MFC after: 5 days
Tested by: krion
following drivers: bfe(4), em(4), fxp(4), lnc(4), tun(4), de(4) rl(4),
sis(4) and xl(4)
More patches are pending on: http://peoples.freebsd.org/~mlaier/ Please take
a look and tell me if "your" driver is missing, so I can fix this.
Tested-by: many
No-objection: -current, -net
sysctls were global (hw.fxp_rnr and hw.fxp_noflow), all of them are
now per-device. Sample output of "sysctl dev.fxp0" with this patch,
with the standard %foo nodes removed :
dev.fxp0.int_delay: 1000
dev.fxp0.bundle_max: 6
dev.fxp0.rnr: 0
dev.fxp0.noflow: 0
In particular, disabling it was likely to break configurations
involving ng_vlan(4) since the latter couldn't control
the parent's VLAN_MTU in the way vlan(4) did.
Pointed out by: ru
this problem put these lines back in. While they should be
unnecessary, they appear to be sometimes necessary.
Reviewed in concept: dfr
Approved by: re (scottl@)
to the pci attachment. Cardbus is a derived class of pci so all pci
drivers are automatically available for matching against cardbus devices.
Reviewed by: imp
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.
This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.
Approved By: re (in principle)
Reviewed By: njl, imp
Tested On: i386, amd64, sparc64
Obtained From: NetBSD (if_xname)
However, they are presently necessary due to bigger bogusness in the
pci bus layer not doing the right thing on suspend/resume or on
initial device probe. This is exactly the sort of thing that the
BURN_BRIDGES option was invented for. Mark all of them as
BURN_BRIDGES. As soon as I have the powerstate stuff properly
integrated into the pci bus code, I intend to remove all these
workarounds.
Add two new arguments to bus_dma_tag_create(): lockfunc and lockfuncarg.
Lockfunc allows a driver to provide a function for managing its locking
semantics while using busdma. At the moment, this is used for the
asynchronous busdma_swi and callback mechanism. Two lockfunc implementations
are provided: busdma_lock_mutex() performs standard mutex operations on the
mutex that is specified from lockfuncarg. dftl_lock() is a panic
implementation and is defaulted to when NULL, NULL are passed to
bus_dma_tag_create(). The only time that NULL, NULL should ever be used is
when the driver ensures that bus_dmamap_load() will not be deferred.
Drivers that do not provide their own locking can pass
busdma_lock_mutex,&Giant args in order to preserve the former behaviour.
sparc64 and powerpc do not provide real busdma_swi functions, so this is
largely a noop on those platforms. The busdma_swi on is64 is not properly
locked yet, so warnings will be emitted on this platform when busdma
callback deferrals happen.
If anyone gets panics or warnings from dflt_lock() being called, please
let me know right away.
Reviewed by: tmm, gibbs
in the netisr case. This would result in a lock reversal. This
fixes the net.isr.enable=1 case. Better performance might be
obtained by chaining all packets received, dropping the lock, and
then calling if_input() on each one.
Reported by: hmp
structure, which is new to the 82550 and 82551, is used to transmit
a packet. This appears to fix the packet truncation problem that was
observed when using 82550-based fxp cards to transmit ICMP or fragmented
UDP packets of certain lengths which only had one to three bytes in the
second and final mbuf of the packet. This matches a note in the "Intel
8255x 10/100 Mbps Ethernet Controller Family Open Source Software Developer
Manual", which says that the hardware parse bit should be set when sending
these types of packets.
There have also been unconfirmed reports of similar problems when
transmitting TCP packets, which should not be affected by the above
mentioned change because the hardware parse bit was already being set
if the stack requested hardware checksumming of the packet. If the
problem remains, the use of the IPCB structure can be disabled to
cause the driver to fall back to using the older 82559 interface with
82550-based cards by setting
hint.fxp.UNIT_NUMBER.ipcbxmit_disable
to a non-zero value at boot time, or using kenv to set this variable
before using kldload to load the fxp driver.
Approved by: re (jhb)
on if_fxp cards. When flow control is enabled, if the operating system
doesn't acknowledge the packet buffer filling, the card will begin to
generate ethernet quench packets, but appears to get into a feedback
loop of some sort, hosing local switches. This is a temporary workaround
for 5.1: the ability to configure flow control should probably be
exposed by some or another management interface on ethernet link layer
devices.
Approved by: re (bmah)
Reviewed by: mux
by using a __packed keyword for the fxp_rfa structure. The Intel
guys who designed this structure with unaligned fields deserve
to be shot.
Tested by: kris
Approved by: re@ (jhb)
Check for suspend before the device polling, rather than after it.
Check to see if the current thread owns the lock in ioctl and return
EBUSY if it does.
This advances the locking to the point that I can eject my fxp card 10
times in a row, but I agree with Jeff Hsu that we need to get the
network layer locking finished before chasing more of the races here
(actually, he doesn't think this set is worth it even). There's a
number of races between FXP_LOCK in detach and all other users of
FXP_LOCK, and this gets back to the 'device with sleepers being
forcibly detached' problem as well...
1) always call fxp_stop in fxp_detach. Since we don't read from
the card, there's no need to carefully look at things with
bus_child_present.
2) Call FXP_UNLOCK() before calling bus_teardown_intr to avoid
a possible deadlock reported by jhb.
3) add gone to the softc. Set it to true in detach.
4) Return immediately if gone is true in fxp_ioctl
5) Return immediately if gone is true in fxp_intr
- Add fxp_start_body() and change fxp_start() to just acquire locks and
then call fxp_start_body(). Places that would call fxp_start() with
locks held (mutex recursion) now call fxp_start_body() directly.
Remove MTX_RECURSE flag from sc_mtx. [gallatin]
- Change fxp_attach() to work without the softc lock, saving interrupt
hooking until the head of fxp_attach().
- Call ether_ifattach() before overriding ifp parameters. This reverts
part of 1.155.
- Remove multiple error paths in fxp_attach().
- Teardown interrupt in fxp_detach() before unlocking the softc.
- Make sure mutex is not held in fxp_release()
- Delete the miibus instance and/or self in fxp_release(), not in
fxp_detach(). This can happen if attach fails partway through.
- Move ifmedia_removeall to fxp_release() since attach may fail after
media have been allocated.
- Add locking to fxp_suspend, fxp_resume, fxp_start, fxp_intr,
fxp_poll, fxp_tick, fxp_ioctl, fxp_watchdog.
- Pass in ifp to fxp_intr_body since its callers sometimes already use
it.
- Add compatibility define for INTR_MPSAFE for 4.x. [gallatin]
- You don't need to bzero softc.
Ideas from: gallatin, mux
Tested by: >400M packets of dd/ssh, NFS, ping on i386 UP
