explicitly rather than relying on name space pollution to pull it in
for us.
NB: The usage of INT_MIN is somewhat bogus and suspect to my eye, but this
commit doesn't address that issue.
the specific semantics of ockmgr aren't required: update UFS1 extended
attributes to protect its data structures using an sx lock.
While here, update comments on lock granularity.
MFC after: 2 weeks
The most important point is that -f option(s) are never copied from
.Ev MAKEFILE to .Va .MAKEFILE by make(1), which is consistent with
handling the command line. (-f silently sit in .Ev MAKEFILE and go
to make's children unless overwritten via .Va .MAKEFILE)
Bump .Dd.
however if current thread is executing cancellation handler, signal
SIGCANCEL may have already been blocked, this is unexpected, unblock the
signal in new thread if this happens.
MFC after: 1 week
The kernel config file is KERNCONF=MPC85XX, so the usual procedure applies:
1. make buildworld TARGET_ARCH=powerpc
2. make buildkernel TARGET_ARCH=powerpc TARGET_CPUTYPE=e500 KERNCONF=MPC85XX
This default config uses kernel-level FPU emulation. For the soft-float world
approach:
1. make buildworld TARGET_ARCH=powerpc TARGET_CPUTYPE=e500
2. disable FPU_EMU option in sys/powerpc/conf/MPC85XX
3. make buildkernel TARGET_ARCH=powerpc TARGET_CPUTYPE=e500 KERNCONF=MPC85XX
Approved by: cognet (mentor)
MFp4: e500
TSEC is the MAC engine offering 10, 100 or 1000 Mbps speed and is found on
different Freescale parts (MPC83xx, MPC85xx). Depending on the silicon version
there are up to four TSEC units integrated on the chip.
This driver also works with the enhanced version of the controller (eTSEC),
which is backwards compatible, but doesn't take advantage of its additional
features (various off-loading mechanisms) at the moment.
Approved by: cognet (mentor)
Obtained from: Semihalf
MFp4: e500
The QUICC engine is found on various Freescale parts including MPC85xx, and
provides multiple generic time-division serial channel resources, which are in
turn muxed/demuxed by the Serial Communications Controller (SCC).
Along with core QUICC/SCC functionality a uart(4)-compliant device driver is
provided which allows for serial ports over QUICC/SCC.
Approved by: cognet (mentor)
Obtained from: Juniper
MFp4: e500
The PQ3 is a high performance integrated communications processing system
based on the e500 core, which is an embedded RISC processor that implements
the 32-bit Book E definition of the PowerPC architecture. For details refer
to: http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=MPC8555E
This port was tested and successfully run on the following members of the PQ3
family: MPC8533, MPC8541, MPC8548, MPC8555.
The following major integrated peripherals are supported:
* On-chip peripherals bus
* OpenPIC interrupt controller
* UART
* Ethernet (TSEC)
* Host/PCI bridge
* QUICC engine (SCC functionality)
This commit brings the main functionality and will be followed by individual
drivers that are logically separate from this base.
Approved by: cognet (mentor)
Obtained from: Juniper, Semihalf
MFp4: e500
native extended attributes. This didn't interfere with the operation of
UFS2 extended attributes, but the code shouldn't be running for UFS2.
MFC after: 2 weeks
a queue entry field, just copy out the unsigned int that is the trigger
message. In practice, auditd always requested sizeof(unsigned int), so
the extra bytes were ignored, but copying them out was not the intent.
MFC after: 1 month
