- O_NONBLOCK flag has to be set, if it is not set, open(2) will wait for
another process opening the fifo for reading,
- Use O_WRONLY which implies that the file has to be opened _only_ for write.
modern dual-core systems as well.
- Parse the _CST packages for each cpu and track all the states individually,
on a per-cpu basis.
- Revert to generic FADT/P_BLK based Cx control if the _CST package
is not present on all cpus. In that case, the new driver will
still support per-cpu Cx state handling. The driver will determine the
highest Cx level that can be supported by all the cpus and configure the
available Cx state based on that.
- Fixed the case where multiple cpus in the system share the same
registers for Cx state handling. To do that, added a new flag
parameter to the acpi_PkgGas and acpi_bus_alloc_gas functions that
enable the caller to add the RF_SHAREABLE flag. This flag could also be
useful to other callers (acpi_throttle?) in the tree but this change is
not yet made.
- For Core Duo cpus, both cores seems to be taken out of C3 state when
any one of the cores need to transition out. This broke the short sleep
detection logic. It is disabled now if there is more than one cpu in
the system for now as it fixed it in my case. This quirk may need to
be re-enabled later differently.
- Added support to control cx_lowest on a per-cpu basis. There is still
a generic cx_lowest to enable changing cx_lowest for all cpus with a single
sysctl and for ease of use. Sample output for the new sysctl:
dev.cpu.0.cx_supported: C1/1 C2/1 C3/57
dev.cpu.0.cx_lowest: C3
dev.cpu.0.cx_usage: 0.00% 43.16% 56.83%
dev.cpu.1.cx_supported: C1/1 C2/1 C3/57
dev.cpu.1.cx_lowest: C3
dev.cpu.1.cx_usage: 0.00% 45.65% 54.34%
hw.acpi.cpu.cx_lowest: C3
This work was done by Stephane E. Potvin with some simple reworking by
myself. Thank you.
Submitted by: Stephane E. Potvin <sepotvin / videotron.ca>
MFC after: 2 weeks
recording enabled some programs (audio/audacity from ports) can't
correctly enumerate all /dev/dsp device.
Note: previous commit did not enable some debugging stuff, my eyes did
misread "#undef" as "#define".
Submitted by: Yuriy Tsibizov <Yuriy.Tsibizov@gfk.ru>
Now (ok it's been a while...) that FreeBSD has RLIMIT_AS too, we can use
it in the linuxolator instead of ignoring it.
This fixes a LTP test.
Submitted by: rdivacky
No need to lock prison in a case of linux_use26 because the int
setting is atomic and process cannot leave jail.
Submitted by: kib
Reviewed by: jhb
Requested by: rdivacky
Dont lock em in a case of just using em->shared->group_pid because
the group_pid never changes.
Submitted by: rdivacky
Reviewed by: kib
Glanced at by: jhb
This is quite tricky situation, because we allow to open a file with
O_RDONLY|O_TRUNC. O_TRUNC modifies a file, but we actually don't open
it for writing. EISDIR is also returned when we try to open a directory
O_RDONLY|O_TRUNC, which is correct.
POSIX says that "The result of using O_TRUNC with O_RDONLY is undefined.",
we choose to accept it (Solaris did the same), that's why "to be modified"
seems more accurate to me.
(due to an early reset or the like), remember to unlock the socket lock.
This will not occur in 7-CURRENT, but could in theory occur in 6-STABLE.
MFC after: 1 week
1. Fix small typo "retorted ." -> "retorted."
2. Remove from fortunes a story that is duplicated in fortunes2-o
3. Remove from fortunes and fortunes2-o Zippy the Pinhead quotes
that are already in the zippy file.
4. ... therefore remove zippy from fortunes.sp.ok
5. Remove a duplicate in the zippy file.
Details: As a side-effect of restoring a saved FP environment,
fesetenv() overwrites the tag word, which indicates which i387
registers are in use. Normally this isn't a problem because
the calling convention requires the register stack to be empty
on function entry and exit. However, fesetenv() is inlined, so we
need to tell gcc explicitly that the i387 registers get clobbered.
PR: 85101
do not call markvoldirty() until the mount has been flagged as read-write.
Due to the nature of the msdosfs code, this bug only seemed to appear for
FAT-16 and FAT-32.
This fixes the testcase:
#!/bin/sh
dd if=/dev/zero bs=1m count=1 oseek=119 of=image.msdos
mdconfig -a -t vnode -f image.msdos
newfs_msdos -F 16 /dev/md0 fd120m
mount_msdosfs -o ro /dev/md0 /mnt
mount | grep md0
mount -u -o rw /dev/md0; echo $?
mount | grep md0
umount /mnt
mdconfig -d -u 0
PR: 105412
Tested by: Eugene Grosbein <eugen grosbein pp ru>
revision 1.98 is NOT merged, because FreeBSD does not support this
syntax.
revision 1.99 is NOT merged, "const poisoning" part is not applicable
to FreeBSD. There is no variable shadowing, GCC can't find
this one (but there are others)
revision 1.100 is NOT merged, because it was null patch (no changes)
revision 1.101 is NOT merged, there is no BIT() macro in FreeBSD
revision 1.102 is merged
revision 1.103 is partially merged. There is no ai.ifaceh in FreeBSD
revision 1.104 is NOT merged
revision 1.105 is merged
revision 1.106 is not merged, because of rev. 1.107
revision 1.107 is a backuout of 1.106
Submitted by: Yuriy Tsibizov <Yuriy.Tsibizov@gfk.ru>
---snip---
New features:
1. Optional multichannel recording (32 channels on Live!, 64 channels
on Audigy).
All channels are 16bit/48000Hz/mono, format is fixed.
Half of them are copied from sound output, another half can be
used to record any data from DSP. What should be recorded is
hardcoded in DSP code. In this version it records dummy data, but
can be used to record all DSP inputs, for example..
Because there are no support of more-than-stereo sound streams
multichannell stream is presented as one 32(64)*48000 Hz 16bit mono
stream.
Channel map:
SB Live! (4.0/5.1)
offset (words) substream
0x00 Front L
0x01 Front R
0x02 Digital Front L
0x03 Digital Front R
0x04 Digital Center
0x05 Digital Sub
0x06 Headphones L
0x07 Headphones R
0x08 Rear L
0x09 Rear R
0x0A ADC (multi-rate recording) L
0x0B ADC (multi-rate recording) R
0x0C unused
0x0D unused
0x0E unused
0x0F unused
0x10 Analog Center (Live! 5.1) / dummy (Live! 4.0)
0x11 Analog Sub (Live! 5.1) / dummy (Live! 4.0)
0x12..-0x1F dummy
Audigy / Audigy 2 / Audigy 2 Value / Audigy 4
offset (words) substream
0x00 Digital Front L
0x01 Digital Front R
0x02 Digital Center
0x03 Digital Sub
0x04 Digital Side L (7.1 cards) / Headphones L (5.1 cards)
0x05 Digital Side R (7.1 cards) / Headphones R (5.1 cards)
0x06 Digital Rear L
0x07 Digital Rear R
0x08 Front L
0x09 Front R
0x0A Center
0x0B Sub
0x0C Side L
0x0D Side R
0x0E Rear L
0x0F Rear R
0x10 output to AC97 input L (muted)
0x11 output to AC97 input R (muted)
0x12 unused
0x13 unused
0x14 unused
0x15 unused
0x16 ADC (multi-rate recording) L
0x17 ADC (multi-rate recording) R
0x18 unused
0x19 unused
0x1A unused
0x1B unused
0x1C unused
0x1D unused
0x1E unused
0x1F unused
0x20..0x3F dummy
Fixes:
1. Do not assign negative values to variables used to index emu_cards
array. This array was never accessed when index is negative, but
Alexander (netchild@) told me that Coverity does not like it.
After this change emu_cards[0] should never be used to identify
valid sound card.
2. Fix off-by-one errors in interrupt manager. Add more checks there.
3. Fixes to sound buffering code now allows driver to use large playback
buffers.
4. Fix memory allocation bug when multichannel recording is not
enabled.
5. Fix interrupt timeout when recording with low bitrate (8kHz).
Hardware:
1. Add one more known Audigy ZS card to list. Add two cards with
PCI IDs betwen old known cards and new one.
Other changes:
1. Do not use ALL CAPS in messages.
Incomplete code:
1. Automute S/PDIF when S/PDIF signal is lost.
Tested on i386 only, gcc 3.4.6 & gcc41/gcc42 (syntax only).
---snip---
This commits enables a little bit of debugging output when the driver is
loaded as a module. I did a cross-build test for amd64.
The code has some style issues, this will be addressed later.
The multichannel recording part is some work in progress to allow playing
around with it until the generic sound code is better able to handle
multichannel streams.
This is supposed to fix
CID: 171187
Found by: Coverity Prevent
Submitted by: Yuriy Tsibizov <Yuriy.Tsibizov@gfk.ru>
Bring the linux mmap code more into line with how linux (2.4.x) behaves.
Tested by: Scot Hetzel <swhetzel@gmail.com> on amd64 without PROT_EXEC
Additionally to the i386 version always use PROT_EXEC in the mapping like the
previous version of the amd64 code did. We need to examinate this further to
decide what the right thing to do is. For now this fixes several problems in
the LTP test runs and should behave regarding PROT_EXEC like before.
of max() when computing the divisor in SCHED_TICK_PRI(). This prevents
cases where rounding down would allow the quotient to exceed
SCHED_PRI_RANGE.
- Garbage collect some unused flags and fields.
- Replace TDF_HOLD with sched_pin_td()/sched_unpin_td() since it simply
duplicated this functionality.
- Re-enable the rebalancer by default and fix the sysctl so it can be
modified.
marked idle, thus breaking cpu load balancing.
- Change sched_interact_update() to fix cases where the stored history
has expanded significantly rather than handling them in the callers. This
fixes a case where sched_priority() could compute a bad value.
- Add a sysctl to disable the global load balancer for experimentation.
server.
Don't complain about a hard loop id of 0xffff- we get this in
point-to-point topologies with the 2300 and 2K Login firmware.
Up the timeout on register FC4 types commands.
- Rename confusing AGP_INTEL_I845_MCHCFG to AGP_INTEL_I845_AGPM.
- Move E7205 and E7505 from i8x5 to i8x0 family. It probably worked
because the actual offset is the same.
In fact, all three families have the bit at the exact same place. Only
differences are name and width of the registers, i.e., NBXCFG (0x50, dword),
RDCR (0x51, byte), AGPM (0x51, byte), MCHCFG (0x50, word) depending on
the family of the chipsets.
