"fatal firmware error" happens. Previously it was neccessary to reset
it manually, using "/etc/rc.d/netif restart".
Approved by: adrian@
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
"fatal firmware error" happens. Previously it was neccessary to reset
it manually, using "/etc/rc.d/netif restart".
Approved by: adrian@
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
direction isochronous transfers.
- Remove setting of fields which does not belong to the respective
TRBs. These fields are currently set as zero and this is more a
cosmetic change.
MFC after: 3 days
Submitted by: Horse Ma <HMa@wyse.com>
- Make sure TX/RX lists don't leak and are only allocated once.
- Fix off-by one transfer index computation.
- Give firmware loading more time.
MFC after: 3 days
be a race when using a single active queue for all transmit types.
- Last argument of usb_pause_mtx() is ticks and not milliseconds.
- Remove unused watchdog.
- Remove some unused fields from the RSU softc structure.
- Workaround usbd_transfer_start() recursion from inside of completion
callback.
MFC after: 3 days
- Need to set the pre-fetch memory address when reading the host memory.
- We currently assume that no endianness conversion is needed.
Sponsored by: DARPA, AFRL
ismt(4) supports the SMBus Message Transport controller found on Intel
C2000 series (Avoton) and S1200 series (Briarwood) Atom SoCs.
Sponsored by: Intel
Intel 40G Ethernet Controller XL710 Family. This is
the core driver, a VF driver called i40evf, will be
following soon. Questions or comments to myself or
my co-developer Eric Joyner. Cheers!
- Implement support for interrupt filters in the DWC OTG driver, to
reduce the amount of CPU task switching when only feeding the FIFOs.
- Add common spinlock to the USB bus structure.
MFC after: 2 weeks
platform code, it is expected these will be merged in the future when the
ARM code is more complete.
Until more boards can be tested only use this with the Raspberry Pi and
rrename the functions on the other SoCs.
Reviewed by: ian@
it doesn't leak through when the command structure is reused for a user
command without a data buffer.
PR: amd64/189668
Tested by: Pete Long <pete@nrth.org>
MFC after: 1 week
Previously only TX IP checksum offloading was disabled but it's
reported that TX checksum offloading for UDP datagrams with IP
options also generates corrupted frames. Reporter's controller is
RTL8168CP but I guess RTL8168C also have the same issue since it
shall share the same core.
Reported and tested by: tuexen
the main processing queue, clear the NAK counter for any associated
BULK or CONTROL transfers and poll the endpoint(s) for 1 millisecond
at 125us rate interval, before going into slow, 10ms, NAK polling mode
again. This has the effect that typical ping-ping protocols respond
quicker when initiated from the USB host.
MFC after: 2 weeks
The last obstacle to switching PowerPC entirely to vt is that the Playstation 3
framebuffer driver needs to be ported over. This only applies for powerpc64,
however.
on my G4 iBook by more than half. Still 10% slower than syscons, but that's
much better than a factor of 2.
The slowness had to do with pathological write performance on 8-bit
framebuffers, which are almost universally used on Open Firmware systems.
Writing 1 byte at a time, potentially nonconsecutively, resulted in many
extra PCI write cycles. This patch, in the common case where it's writing
one or several characters in an 8x8 font, gangs the writes together into
a set of 32-bit writes. This is a port of r143830 to vt(4).
The EFI framebuffer is also extremely slow, probably for the same reason,
and the same patch will likely help there.
This driver supports the low and high precision models (9 and 11 bits) and
it will auto-detect the both variants.
The driver expose the temperature registers (actual temperature, shutdown
and hysteresys temperature) and also the configuration register.
It was tested on FDT systems: RPi, BBB and on non-FDT systems: AR71xx, with
both, hardware i2c controllers (when available) and gpioiic(4).
This provides a simple and cheap way for verifying the i2c bus on embedded
systems.
- For non-periodic traffic we only need to wait two SOFs before
disabling the channel.
- Make sure we release the TX FIFO tracking level after the host
channel is disabled.
- Make sure the host channel state gets reset/disabled initially.
- Two minor code style changes.
MFC after: 2 weeks
