In r304435, ip_output() was changed to use the result of the route
lookup to decide whether the outgoing packet was a broadcast or
not. This introduced a regression on interfaces where
IFF_BROADCAST was not set (e.g. point-to-point links), as the
algorithm could incorrectly treat the destination address as a
broadcast address, and ip_output() would subsequently drop the
packet as broadcasting on a non-IFF_BROADCAST interface is not
allowed.
Differential Revision: https://reviews.freebsd.org/D8303
Reviewed by: jtl
Reported by: ambrisko
MFC after: 2 weeks
X-MFC-With: r304435
Sponsored by: Dell EMC Isilon
- Make !KDB config buildable.
- Simplify interface to nmi_handle_intr() by evaluating panic_on_nmi
in one place, namely nmi_call_kdb(). This allows to remove do_panic
argument from the functions, and to remove i386/amd64 duplication of
the variable and sysctl definitions. Note that now NMI causes
panic(9) instead of trap_fatal() reporting and then panic(9),
consistently for NMIs delivered while CPU operated in ring 0 and 3.
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
environment variable to allow conditional compilation based on EFI
being present or not. Provide efi-setenv, efi-getenv, and
efi-unsetenv, though those need improvement. Move the efi definition
to libefi (but include a reference so they get included).
Push-Pull Two Wire interface is a almost compatible iic like bus used
in sun6i SoC. It's only use is to communicate with the power management IC.
Reviewed by: jmcneill
MFC after: 1 week
Relnotes: yes
contiguous regions in an mbuf chain.
If the payload of an mbuf ends at a page boundary count_mbuf_nsegs would
incorrectly consider the next mbuf's payload physically contiguous based
solely on a KVA comparison.
MFC after: 1 week
Sponsored by: Chelsio Communications
On several Intel chipsets, diagnostic NMIs sent from BMC or NMIs
reporting hardware errors are broadcasted to all CPUs.
When kernel is configured to enter kdb on NMI, the outcome is
problematic, because each CPU tries to enter kdb. All CPUs are
executing NMI handlers, which set the latches disabling the nested NMI
delivery; this means that stop_cpus_hard(), used by kdb_enter() to
stop other cpus by broadcasting IPI_STOP_HARD NMI, cannot work. One
indication of this is the harmless but annoying diagnostic "timeout
stopping cpus".
Much more harming behaviour is that because all CPUs try to enter kdb,
and if ddb is used as debugger, all CPUs issue prompt on console and
race for the input, not to mention the simultaneous use of the ddb
shared state.
Try to fix this by introducing a pseudo-lock for simultaneous attempts
to handle NMIs. If one core happens to enter NMI trap handler, other
cores see it and simulate reception of the IPI_STOP_HARD. More,
generic_stop_cpus() avoids sending IPI_STOP_HARD and avoids waiting
for the acknowledgement, relying on the nmi handler on other cores
suspending and then restarting the CPU.
Since it is impossible to detect at runtime whether some stray NMI is
broadcast or unicast, add a knob for administrator (really developer)
to configure debugging NMI handling mode.
The updated patch was debugged with the help from Andrey Gapon (avg)
and discussed with him.
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D8249
The feature flags chek is missing the corner case where we have valid pool
version, but feature flags are not enabled - as for example plain v28 pool.
This update does fix the boot support for such pools.
Reviewed by: avg, allanjude
Approved by: allanjude (mentor)
Differential Revision: https://reviews.freebsd.org/D8331
Link status check is much more lightweight than network change detection.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8311
This will not happen in real world, since TX consumption of the vmbus
TX bufring is limitted. Better safe than sorry.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8309
All RNDIS control messages have used SG list for a while. This makes
the send context suitable for further refactoring.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8308
prevent overheating.
When sensor 0's alarm interrupt is fired, set a throttle flag. Further
requests to set CPU frequency will be rejected until sensor 0's temperature
returns to a level below the hot temperature threshold.
Relnotes: yes
native fueword64(9) still, use proper type for local where fuword64()
result is stored.
Note that fueword64() is unused in the tree.
Submitted by: Chunhui He <hchunhui@mail.ustc.edu.cn>
PR: 212520
MFC after: 1 week
- Use ums lock as evdev lock
- Do not cap axes values to sysmouse limits for evdev reports
- Do not map T-axis events to buttons for evdev reports
- Use shortcuts for event reporting
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
MFC after: 1 week
Add wrappers around generic evdev_push_event for specific event types:
EV_KEY/EV_REL/EV_ABS etc...
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
The driver currently supports chips that are fully compliant with the
JEDEC SPD / EEPROM / TS standard (JEDEC Standard 21-C,
TSE2002 Specification, frequenlty referred to as JEDEC JC 42.4).
Additionally some chips from STMicroelectronics are supported as well.
They are compliant except for their Device ID pattern.
Given the continued lack of any common sensor infrastructure, the driver
uses an ad-hoc sysctl to report the temperature.
Reviewed by: wblock (documentation)
MFC after: 2 weeks
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D8174
If the device tree doesn't contain a cpu-handle field in any bman-portal or
qman-portal, it will exit without setting up the devinfo, leaving it
uninitialized. This will lead to attempts to free random memory, and ultimately
panic.
Summary:
The Freescale e500v2 PowerPC core does not use a standard FPU.
Instead, it uses a Signal Processing Engine (SPE)--a DSP-style vector processor
unit, which doubles as a FPU. The PowerPC SPE ABI is incompatible with the
stock powerpc ABI, so a new MACHINE_ARCH was created to deal with this.
Additionaly, the SPE opcodes overlap with Altivec, so these are mutually
exclusive. Taking advantage of this fact, a new file, powerpc/booke/spe.c, was
created with the same function set as in powerpc/powerpc/altivec.c, so it
becomes effectively a drop-in replacement. setjmp/longjmp were modified to save
the upper 32-bits of the now-64-bit GPRs (upper 32-bits are only accessible by
the SPE).
Note: This does _not_ support the SPE in the e500v1, as the e500v1 SPE does not
support double-precision floating point.
Also, without a new MACHINE_ARCH it would be impossible to provide binary
packages which utilize the SPE.
Additionally, no work has been done to support ports, work is needed for this.
This also means no newer gcc can yet be used. However, gcc's powerpc support
has been refactored which would make adding a powerpcspe-freebsd target very
easy.
Test Plan:
This was lightly tested on a RouterBoard RB800 and an AmigaOne A1222
(P1022-based) board, compiled against the new ABI. Base system utilities
(/bin/sh, /bin/ls, etc) still function appropriately, the system is able to boot
multiuser.
Reviewed By: bdrewery, imp
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D5683
libc++'s stddef.h includes an existing definition of max_align_t for
C++11, but it is only defined for C++, not for C. In addition, GCC and
clang both define an alternate version of max_align_t that uses a
union of multiple types rather than a plain long double as in libc++.
This adds a __max_align_t to <sys/_types.h> that matches the GCC and
clang definition that is mapped to max_align_t in <stddef.h>.
PR: 210890
Reviewed by: dim
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D8194
In sendit(), if mp->msg_control is present, then in sockargs() we are
allocating mbuf to store mp->msg_control. Later in kern_sendit(), call
to getsock_cap(), will check validity of file pointer passed, if this
fails EBADF is returned but mbuf allocated in sockargs() is not freed.
Made code changes to free the same.
Since freeing control mbuf in sendit() after checking (control != NULL)
may lead to double freeing of control mbuf in sendit(), we can free
control mbuf in kern_sendit() if there are any errors in the routine.
Submitted by: Lohith Bellad <lohith.bellad@me.com>
Reviewed by: glebius
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D8152
