Also ensure dsb precedes isb in all icache maintenance routines (first
do a data sync, then stall the instruction stream until it finishes).
Submitted by: Michal Meloun
been done by U-Boot. This allows the USB to work when we load the kernel
directly.
No dma sync is performed after these operations as the data we read/write
is not used by the cpu after the calls to the maimbox driver.
Differential Revision: https://reviews.freebsd.org/D1940
Reviewed by: imp, Michal Meloun (meloun AT miracle.cz)
MFC after: 1 Week
Sponsored by: ABT Systems Ltd
both the post-filter and post-thread callbacks.
Also eliminate a completely unecessary write to INTC_ISR_CLEAR register,
which clears a software-generated interrupt that can only happen with a
write to INTC_ISR_SET (which nothing does).
uart implementations, and export them using the new linker-set mechanism.
Differential Revision: https://reviews.freebsd.org/D1993
Submitted by: Michal Meloun
PL (programmable logic) uses FCLK0..FCLK3 as a clock sources.
Normally they're configured by first stage boot loader (FSBL)
and normal user never has to touch them. These sysctls may come
useful for hardware developers
hw.fpga.fclk.N.source: clock source (IO, DDR, ARM)
hw.fpga.fclk.N.freq: requested frequency in Hz
hw.fpga.fclk.N.actual_freq: actual frequency in Hz (R/O)
hw.fgpa.level_shifters: 0/1 to enable/disable PS-PL level shifters,
normally they're enabled either by FSBL or after programming
FPGA through devcfg(4)
emulate the instructions used in function entry and exit.
For function entry ARM will use a push instruction to push up to 16
registers to the stack. While we don't expect all 16 to be used we need to
handle any combination the compiler may generate, even if it doesn't make
sense (e.g. pushing the program counter).
On function return we will either have a pop or branch instruction. The
former is similar to the push instruction, but with care to make sure we
update the stack pointer and program counter correctly in the cases they
are either in the list of registers or not. For branch we need to take the
24-bit offset, sign-extend it, and add that number of 4-byte words to the
program counter. Care needs to be taken as, due to historical reasons, the
address the branch is relative to is not the current instruction, but 8
bytes later.
This allows us to use the following probes on ARM boards:
dtrace -n 'fbt::malloc:entry { stack() }'
and
dtrace -n 'fbt:🆓return { stack() }'
Differential Revision: https://reviews.freebsd.org/D2007
Reviewed by: gnn, rpaulo
Sponsored by: ABT Systems Ltd
the translation table (this may be left over from armv5 days). It's
especially bad to do so using a cache operation that isn't coherent on
SMP systems.
Submitted by: Michal Meloun
used by other places that expect to unwind the stack, e.g. dtrace and
stack(9).
As I have written most of this code I'm changing the license to the
standard FreeBSD license. I have received approval from the other
developers who have changed any of the affected code.
Approved by: ian, imp, rpaulo, eadler (all license change)
Switch the cache line size during invalidations/flushes
to be read from CP15 cache type register.
Submitted by: Wojciech Macek <wma@semihalf.com>
Reviewed by: ian, imp
Obtained from: Semihalf
With this commit any of the GPIO pins can now be programmed to act as an
interrupt source for GPIO devices (i.e. limited to devices directly
attached to gpiobus - at least for now).
Differential Revision: https://reviews.freebsd.org/D1000
The DISP DPLL clock is slower and was making the PRU programs slower
on FreeBSD than on Linux.
Submitted by: Manuel Stuehn <freebsdnewbie at freenet.de>
MFC after: 1 week
const. On x86, even after the machine context is supposedly read into
the struct ucontext, lazy FPU state save code might only mark the FPU
data as hardware-owned. Later, set_fpcontext() needs to fetch the
state from hardware, modifying the *mcp.
The set_mcontext(9) is called from sigreturn(2) and setcontext(2)
implementations and old create_thread(2) interface, which throw the
*mcp out after the set_mcontext() call.
Reported by: dim
Discussed with: jhb
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Allocate all four, we will use them soon.
Simplificate the allocation of memory and interrupt resources with a single
bus_alloc_resources() call instead of doing them separately.
Destroy the mutex in case of errors.
With this change, it is now possible to verify the pin function and level
of reserved pins (but not set them).
The use of reserved pins on Raspberry pi can lead to short circuits and
real damage to the SoC.
While here, remove duplicated code, make use of OF_getencprop_alloc()
instead of using fixed sized variables and reduce the dmesg spam by
printing reserved pin ranges (when possible) instead of printing each pin
in the range.
string.
With this change it is not necessary redeclare the driver relations with
gpiobus and gpioc.
This also prevents redundant declarations when gpiobusvar.h is included
(which is going to happen soon).
