may not be desired if you're just going to blow the kernel away again later)
and substitute one that tells the user where the new kernel build
directory actually IS, which can at least be argued to be useful information
in all cases.
Reviewed by: davidg
ypbind.c:
Make fewer assumtions about the state of the dom_alive and dom_broadcasting
flags in roc_received().
Cosmetic changes and paranoia checks:
ypbind.c:
Make fewer assumtions about the state of the dom_alive and dom_broadcasting
flags in roc_received().
If select() fails, use syslog() to report the error rather than perror().
Check that all our malloc()s succeed. Report malloc() failure in
ypbindproc_setdom_2() to callers.
yplib.c:
Use #defined constants in ypbinderr_string() rather than hard-coded values.
ypbind.c:
Make fewer assumtions about the state of the dom_alive and dom_broadcasting
flags in roc_received().
If select() fails, use syslog() to report the error rather than perror().
Check that all our malloc()s succeed. Report malloc() failure in
ypbindproc_setdom_2() to callers.
yplib.c:
Use #defined constants in ypbinderr_string() rather than hard-coded values.
Added CONTROL device that only does user-ioctl and nothing else;
Added protection so user-ioctl requires write access;
Clean up scsiconf.h a little. It needs more work.
- set TCP_NOPUSH to keep from sending short packets at each write(2) boundary
- set SO_SNDBUF to 64k so we have a reasonable amount of buffer space
- for a regular file in binary mode which is not being restarted and is
. smaller than 16 Meg, use mmap(2) and write(2) the whole file in one big
gulp
In the most common circumstances, this should dramatically reduce the
system-call load from ftpd, since the call to write() will not return until
the entire file has been written, rather than writing just a few K at a time
in a loop.
In the case where ypserv is started with the -dns flag, fall through to
the DNS lookup code only if asked to match a map with the word 'host'
in its name. This prevents failed matches on non-host maps from being
incorrectly handed off to DNS.
the lookup fails. Updated callers to deal with this. Call in_pcblookuphash
instead of in_pcblookup() in in_pcbconnect; this improves performance of
UDP output by about 17% in the standard case.
Remove bogus targets.
Allocate partition letters as follows:
lowest offset "flags & CHUNK_IS_ROOT" gets 'a',
lowest offset "subtype==FS_SWAP" gets 'b'
the rest is allocated in offset order from this sequence "defghab".
This will generally make sense.
Added rules to complain if more than one CHUNK_IS_ROOT or more than one
FS_SWAP per FreeBSD chunk.
Set CHUNK_IS_ROOT on the 'a' partition in Open_Disk.
Run Fixup_Names in Open_Disk.
Correct Makefile so that we build during all: and only install for
make install.
If /etc/sysconfig exists source it to get the flags for restarting
named with. If /etc/sysconfig says no named runs, don't try to start one.
Don't attempt to kill anything if we can not find the named.pid file.
Reviewed by: Nickolay N. Dudorov <nnd@gw.itfs.nsk.su>
space for the hash list buckets and is a little faster. The features
of tailq aren't needed. Increased the size of the object hash table
to improve performance. In the future, this will be changed so that
the table is sized dynamically.
as side-effect, removed some legacy code that was necessary
when we called vm_fault inside of vm_fault_quick instead of using
the kernel/user space byte move routines.
(2GB). If this limit is not imposed, then filesystem corruption will
ensue when files larger than 2GB are created. This is temporary,
and the underlying limitation will be removed later.
nor is it in sync with my working sources, but it leaves me less CVS hassles
to bring in the new files at this time. Still no documentation to translate
quite yet, but soon. This stuff is actually very close now.
algorithm is used on aic7770 Rev E or higher chips to improve perfomance.
This required a hardware change but we don't know exactly what (most
likely some special register to do fast SCB indexing into host memory),
and we are not at all sure that there are more than 4 SCBs on these
chips. This probe will still classify the revision of the aic7xxx, but
we now default to 4 SCBs (at least until we know more of what was done).
This also fixes a bug in the timeout routine where we cleared a flag
too soon making it imposible to enter one section of the routine.
Submitted by: Timeout bug - Dan Eischen <deischen@iworks.InterWorks.org>
interrupts to zero to start with. This is the value we return in
most cases. The sense code then outbs the apropriate value to cause
sense retrieval. The return value was uninitialized before this
change (something that was an okay thing with the old sequencer code,
but not with the semantics of the new).
This problem caused us to always retrieve sense upon recieving a non
zero status byte. This is exactly what was happening for the "target
busy" status returned by exabyte tape drives when they rewind or
power on with a tape installed. The request sense proved fatal.
This should fix the tape problems.
