table. The 'locked' attribute is used to circumvent the regular page table
locking for some special pages, with the result that including locked pages
here causes races when updating the stats.
logic to support modifying the page table through a hypervisor. This
uses KOBJ inheritance to provide subclasses of the base 64-bit AIM MMU
class with additional methods for page table manipulation.
Many thanks to Peter Grehan for suggesting this design and implementing
the MMU KOBJ inheritance mechanism.
Passing a count of zero on i386 and amd64 for [I386|AMD64]_BUS_SPACE_MEM
causes a crash/hang since the 'loop' instruction decrements the counter
before checking if it's zero.
PR: kern/80980
Discussed with: jhb
byte-swapped versions of compile-time constants. This allows use of
bswap() and htole*() in initializers, which is required to cross-build
btxld.
Obtained from: sparc64
i.e. alignment, max_address, max_iosize and segsize (only max_address is
thought to have an negative impact regarding this issue though), after
calling ata_dmainit() either directly or indirectly so these values have
no effect or at least no effect on the DMA tags and the defaults are used
for the latter instead. So change the drivers to set these parameters
up-front and ata_dmainit() to honor them.
This file was missed in r216013.
Submitted by: nwhitehorn
DPCPU_DEFINE and VNET_DEFINE macros, as these cause problems for various
people working on the affected files. A better long-term solution is
still being considered. This reversal may give some modules empty
set_pcpu or set_vnet sections, but these are harmless.
Changes reverted:
------------------------------------------------------------------------
r215318 | dim | 2010-11-14 21:40:55 +0100 (Sun, 14 Nov 2010) | 4 lines
Instead of unconditionally emitting .globl's for the __start_set_xxx and
__stop_set_xxx symbols, only emit them when the set_vnet or set_pcpu
sections are actually defined.
------------------------------------------------------------------------
r215317 | dim | 2010-11-14 21:38:11 +0100 (Sun, 14 Nov 2010) | 3 lines
Apply the STATIC_VNET_DEFINE and STATIC_DPCPU_DEFINE macros throughout
the tree.
------------------------------------------------------------------------
r215316 | dim | 2010-11-14 21:23:02 +0100 (Sun, 14 Nov 2010) | 2 lines
Add macros to define static instances of VNET_DEFINE and DPCPU_DEFINE.
that causes AP bringup to fail if some of the Cell HID-register code
is anywhere in the instruction stream. Pending a better solution, cache
performance on SMP Cell systems running without a hypervisor will be
suboptimal.
mappings need to end up in the kernel anyway since the kernel begins
executing in OF context. Separating them adds needless complexity,
especially since the powerpc64 and mmu_oea64 code gave up on it a long
time ago.
As a side effect, the PPC ofw_machdep code is no longer AIM-specific,
so move it to powerpc/ofw.
hypervisor infrastructure support:
- Fix coexistence of multiple platform modules in the same kernel
- Allow platform modules to provide an SMP topology
- PowerPC hypervisors limit the amount of memory accessible in real mode.
Allow the platform modules to specify the maximum real-mode address,
and modify the bits of the kernel that need to allocate
real-mode-accessible buffers to respect this limits.
routines.
This unbreaks Book-E build after the recent machine/mutex.h removal.
While there move tlb_*lock() prototypes to machine/tlb.h.
Submitted by: jhb
MSR[DEEPNAP] be set, not just MSR[DEEPNAP]. Fixing this reduces the idle
temperature of my CPUs from 57 to 38 degrees and makes one-shot timer
mode work properly.
Hint from: mav
MFC after: 4 days
contents of the ones that were not empty were stale and unused.
- Now that <machine/mutex.h> no longer exists, there is no need to allow it
to override various helper macros in <sys/mutex.h>.
- Rename various helper macros for low-level operations on mutexes to live
in the _mtx_* or __mtx_* namespaces. While here, change the names to more
closely match the real API functions they are backing.
- Drop support for including <sys/mutex.h> in assembly source files.
Suggested by: bde (1, 2)
work properly with single-stepping in a kernel debugger. Specifically,
these routines have always disabled interrupts before increasing the nesting
count and restored the prior state of interrupts after decreasing the nesting
count to avoid problems with a nested interrupt not disabling interrupts
when acquiring a spin lock. However, trap interrupts for single-stepping
can still occur even when interrupts are disabled. Now the saved state of
interrupts is not saved in the thread until after interrupts have been
disabled and the nesting count has been increased. Similarly, the saved
state from the thread cannot be read once the nesting count has been
decreased to zero. To fix this, use temporary variables to store interrupt
state and shuffle it between the thread's MD area and the appropriate
registers.
In cooperation with: bde
MFC after: 1 month
only, and should be protected with an ifdef, and the no-execute bit in
32-bit set_user_sr() should be set before the comparison, not after, or
it will never match.
set_user_sr() itself caches the user segment VSID, there is no need for
cpu_switch() to do it again. This change also unifies the 32 and 64-bit
code paths for kernel faults on user pages and remaps the user SLB slot
on 64-bit systems when taking a syscall to avoid some unnecessary segment
exception traps.
concurrency bug. Since all SLB/SR entries were invalidated during an
exception, a decrementer exception could cause the user segment to be
invalidated during a copyin()/copyout() without a thread switch that
would cause it to be restored from the PCB, potentially causing the
operation to continue on invalid memory. This is now handled by explicit
restoration of segment 12 from the PCB on 32-bit systems and a check in
the Data Segment Exception handler on 64-bit.
While here, cause copyin()/copyout() to check whether the requested
user segment is already installed, saving some pipeline flushes, and
fix the synchronization primitives around the mtsr and slbmte
instructions to prevent accessing stale segments.
MFC after: 2 weeks
PowerMac7,2.
- The fcu driver lets us read and write the fan RPMs for all fans in the
PowerMac7,2. This driver is PowerMac specific.
- The ds1775 is a driver to read the temperature for the drive bay sensor.
- The max6690 is another driver to read temperatures. Here it is used to
read the inlet, the backside and the U3 heatsink temperature.
An additional driver, the ad7417, will follow later.
Thanks to nwhitehorn for guiding me through this driver development.
Approved by: nwhitehorn (mentor)
values to zero. A correct solution would involve emulating vector
operations on denormalized values, but this has little effect on accuracy
and is much less complicated for now.
MFC after: 2 weeks
Unlike actual MTRR, this only controls the mapping attributes for
subsequent mmap() of /dev/mem. Nonetheless, the support is sufficiently
MTRR-like that Xorg can use it, which translates into an enormous increase
in graphics performance on PowerPC.
MFC after: 2 weeks
and set memory attributes appropriately for mmap() calls on /dev/console.
Xorg no longer uses /dev/console to mmap the framebuffer, so framebuffer
write combining support in X will arrive in the next patch.
by just caching the mode for later use by pmap_enter(), following amd64.
While here, correct some mismerges from mmu_oea64 -> mmu_oea and clean
up some dead code found while fixing the fictitious page behavior.
The check for alignment should be made against the physical address and not
the virtual address that maps it.
Sponsored by: NetApp
Submitted by: Will McGovern (will at netapp dot com)
Reviewed by: mjacob, jhb
