not change interrupt vector if it is not pointing the ROM itself. Actually,
we just fail shadowing altogether if that is the case because the shadowed
copy will be useless for sure and POST may not be relocatable or useful.
While I'm here, fix a debugging message under bootverbose, really. r211829
fixed one case but broke another. Mea Culpa.
or not by comparing reported TX consumer index with saved index. So
remove unnecessary check done after freeing transmitted mbufs.
While I'm here nuke unnecessary variable initializations.
tag. All controllers that are not BCM5755 or higher have 4GB
boundary DMA bug. Previously bge(4) used 32bit DMA address to
workaround the bug(r199670). However this caused the use of bounce
buffers such that it resulted in poor performance for systems which
have more than 4GB memory. Because bus_dma(9) honors boundary
restriction requirement of DMA tag for dynamic buffers, having a
separate TX/RX mbuf DMA tag will greatly reduce the possibility of
using bounce buffers. For DMA buffers allocated with
bus_dmamem_alloc(9), now bge(4) explicitly checks whether the
requested memory region crossed the boundary or not.
With this change, only the DMA buffer that crossed the boundary
will use 32bit DMA address. Other DMA buffers are not affected as
separate DMA tag is created for each DMA buffer.
Even if 32bit DMA address space is used for a buffer, the chance to
use bounce buffer is still very low as the size of buffer is small.
This change should eliminate most usage of bounce buffers on
systems that have more than 4GB memory.
More correct fix would be teaching bus_dma(9) to honor boundary
restriction for buffers created with bus_dmamem_alloc(9) but it
seems that is not easy.
While I'm here cleanup bge_dma_map_addr() and remove unnecessary
member variables in bge_dmamap_arg structure.
Tested by: marcel
heavy I/O load.
Many thanks to LSI for continuing to support FreeBSD.
PR: kern/149968
Submitted by: LSI (Tom Couch)
Reported by: Kai Kockro <kkockro web de>
Tested by: Kai Kockro, jpaetzel
MFC after: 7 days
configuration function. For failed memory allocations, em(4)/lem(4)
called panic(9) which is not acceptable on production box.
igb(4)/ixgb(4)/ix(4) allocated the required memory in stack which
consumed 768 bytes of stack memory which looks too big.
To address these issues, allocate multicast array memory in device
attach time and make multicast configuration success under any
conditions. This change also removes the excessive use of memory in
stack.
Reviewed by: jfv
Just showing some buffer allocation error is more appropriate
action for drivers. This should fix occasional panic reported on
em(4) when driver encountered resource shortage.
Reviewed by: jfv
supported by many BIOSes to improve performance of VESA BIOS calls for real
mode OSes but it is not our intention here. However, this may help some
platforms where the video ROMs are inaccessible after suspend, for example.
Note it may consume up to 64K bytes of contiguous memory depending on video
controller model when it is enabled. This feature can be disabled by
setting zero to 'debug.vesa.shadow_rom' loader tunable via loader(8) or
loader.conf(5). The default is 1 (enabled), for now.
ID, plus the ability to force '16-bit mode' which really means NE-2000
mode. Other open source drivers suggest that the Holtek misbehaves if
you allow the 8-bit probe. Also, all of the PCI chips emulate
NE-2000ish cards, so always force 16-bit mode for memory transfers.
PR: 84202 (patch not used)
I'm not sure whether adding this logical id is correct or not
because Compex RL2000 is in the list of supported hardware list.
I guess the Compex RL2000 could be PCI variant while the controller
in question is ISA controller. It seems PNP compat id didn't match
or it had multiple compat ids so isa_pnp_probe() seemed to return
ENOENT.
PR: kern/80853
support WOL. Some controllers require additional 3-wire auxiliary
remote wakeup connector to draw power. More recent xl(4)
controllers may not need the wakeup connector though.
initialize controller from a known good state. Previously driver
used to issue controller reset while TX/RX DMA are in progress.
I guess resetting controller in active TX/RX DMA cycle is to ensure
stopping I/Os in xl_shutdown(). I remember some buggy controllers
didn't respond with stop command if controller is under high
network load at the time of shutdown so resetting controller was
the only safe way to stop the I/Os. However, from my experiments,
controller always responded with stop command under high network
load so I think it's okay to remove the xl_reset() in
device_shutdown handler.
Resetting controller also will clear configured RX filter which
in turn will make WOL support hard because driver have to reprogram
RX filter in WOL handler as well as setting station address.
datagrams with checksum value 0 when TX UDP checksum offloading is
enabled. Generating UDP checksum value 0 is RFC 768 violation.
Even though the probability of generating such UDP datagrams is
low, I don't want to see FreeBSD boxes to inject such datagrams
into network so disable UDP checksum offloading by default. Users
still override this behavior by setting a sysctl variable or loader
tunable, dev.bge.%d.forced_udpcsum.
I have no idea why this issue was not reported so far given that
bge(4) is one of the most commonly used controller on high-end
server class systems. Thanks to andre@ who passed the PR to me.
PR: kern/104826
Makefiles or *.mk files, use ${CC:T:Mfoo} instead, so only the basename
of the compiler command (excluding any arguments) is considered.
This allows you to use, for example, CC="/nondefault/path/clang -xxx",
and still have the various tests in bsd.*.mk identify your compiler as
clang correctly.
ICC if cases were also changed.
Submitted by: Dimitry Andric <dimitry at andric.com>
method is used by the PCI bus driver to query the power management system
to determine the proper device state to be used for a device during suspend
and resume. For the ACPI PCI bridge drivers this calls
acpi_device_pwr_for_sleep(). This removes ACPI-specific knowledge from
the PCI and PCI-PCI bridge drivers.
Reviewed by: jkim
