DDB when the interrupt button (aka the "programmer's switch") is pressed.
This isn't unfortunately an NMI, but it's a handy way to get into DDB
quickly if needed.
- Move the command timeout check from a separate repeating timeout to the
kthread since the kthread is already running periodically.
- Move printing the hardware print buffer to the kthread.
- Properly shut down the kernel thread on detach.
- Detach the child array devices on detach.
- Don't issue a controller halt command on detach. Doing so requires a PCI
reset to wake the controller back up. The driver can now be unloaded as
long as CAM support is not enabled.
similar patch has been in 4.x for a while, but is more hacky there.)
For this to work, vinum has to be loaded early (e. g. from
boot/loader), for obvious reasons. If the kernel env variable
(aka. loader variable) "vinum.autostart" is set, vinum then asks the
sysctl kern.disks for all available disks in the system, and scans
them for possible vinum headers.
For statically compiled kernels, this behaviour can be obtained even
without boot/loader by using "options VINUM_AUTOSTART" (though this is
not the recommended way).
Alternatively, the 4.x way to specify "vinum.drives" is also supported.
No further hacks (like the 4.x "vinum.root" variable) are needed,
since in 5.x, mountroot() asks back at the drivers to have them
resolve the name of the root FS into a dev_t (using the dev_clone
eventhandler).
(The MFC reminder below is for a partial MFC for vinum.autostart, the
rest is already there in 4.x.)
Timed out on: grog
MFC after: 2 weeks
we have the rc4 code already in the kernel (via wlan stuff or awi).
Add a dependency on the rc4 module so if it doesn't exist then load it.
Reviewed by: archie
1) It is already called in init_main.c:proc0_post()
2) It is called each time read_random_phony() called, because "initialized"
variable is never set to 1.
Approved by: markm
- Add hid.h
Obtained from: NetBSD
NOTE: This undoes some changes I'd made to prefix the processor name defines
with PVR_. This was due to my original decision to use MPC750 as a cpu name.
With this changed, the PVR_ change is no longer required.
Remove all the stuff that does not relate to the TSC.
Change the calibration to use DELAY(1000000) rather than trying to check
it against the CMOS RTC, this drastically increases precision:
Using 25 samples on a Athlon 700MHz UP machine I find:
stddev min max average
CMOS 22200 Hz -74980 Hz 34301 Hz 704928721 Hz
DELAY 1805 Hz -1984 Hz 2678 Hz 704937583 Hz
(The difference between the two averages is not statistically significant.)
expressed in PPM of the frequency:
stddev min max
CMOS 31.49 PPM -106.37 PPM 48.66 PPM
DELAY 2.56 PPM 2.81 PPM 3.80 PPM
This code will not be used until a followup commit to sys/isa/clock.c
and sys/pc98/pc98/clock.c which will only happen after some field testing.
MAC policy. To load a KLD, require that the subject hold Biba privilege,
and the the kernel module be marked as high integrity. To unload a
KLD, require that the subject hold Biba privilege.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
and MLS policies: as we support both an effective (single) element and
range (available) elements, require that the single be in the range if
both the single and range are defined in the update. Remove comments
suggesting that such a check might be a good idea.
Don't introduce a similar check for network interfaces; due to different
interpretations of the single and range elements, it's not clear that
it's useful to do so.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
labeling for Biba.
Rename the variable 'level' to 'type' in interface parsing and
labeling for MLS.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
uio segment is empty. In this case no dma segment is create by
bus_dmamap_load_buffer, but the calling routine clears the first flag.
Under certain combinations of addresses of the first and second mbuf/uio
buffer this leads to corrupted DMA segment descriptors. This was already
fixed by tmm in sparc64/sparc64/iommu.c.
PR: kern/47733
Reviewed by: sam
Approved by: jake (mentor)
some USB devices. (Make sure to set xfer data length when we force
a short inquiry.)
Obtained from: NetBSD(sys/dev/usb/umass_scsipi.c rev.1.8)
Original idea from: Shingo WATANABE <nabe@nabechan.org>
This is a band-aid while I fret over how much breakage removing the
restriction entirely will result in.
Please note that this is still a limit for the entire pathname
relative to the mountpoint of devfs, so the length of "/dev/fd/3"
is 4 characters.
Change the si_name of dev_t's to be a char * and put a private buffer for
holding the name at then end of the struct.
Initialize si_name to point to the private buffer.
Put a KASSERT in geom_disk to prevent overrun on the fake dev_t we still
have to generate for the disk_drivers.
prevent the compiler from optimizing assignments into byte-copy
operations which might make access to the individual fields non-atomic.
Use the individual fields throughout, and don't bother locking them with
Giant: it is no longer needed.
Inspired by: tjr
statclock based on profhz when profiling is enabled MD, since most platforms
don't use this anyway. This removes the need for statclock_process, whose
only purpose was to subdivide profhz, and gets the profiling clock running
outside of sched_lock on platforms that implement suswintr.
Also changed the interface for starting and stopping the profiling clock to
do just that, instead of changing the rate of statclock, since they can now
be separate.
Reviewed by: jhb, tmm
Tested on: i386, sparc64
this will cause volume labels to be exposed in /dev/vol/<volname>. Currently,
there is no conflict resolution if more than one FS has the same volume name.
Reviewed by: phk
of knowing data size transformations of feeder chain and in some cases
this means too much data is pulled through chain, eg converting input
stream from 16bits to 8bits on 16bit only h/w.
PR: kern/37831
Submitted by: Harti Brandt <brandt@fokus.fraunhofer.de>
at 0 as designed. Its BSD adaptation tries to fight it by mapping 0 to
2147483647 after calculation, but this method not works since 2147483647
seed returns to 0 again on the next interation. Instead of after calculation
mapping, map 0 to another value _before_ calculation, so it never stucks.
- Fix overwrite problem of freed buffers. It was rare but could happen
when fwohci_arcv() is called before fwohci_txd() is called for
the transcation.
- Drain AT queues and pend AR queues on SID receive rather than BUS reset to
make sure DMA actually stops.
- Do agent reset in sbp_timeout().
have some negative effect on interactivity but it yields great perf. gains.
This also brings the conditions under which ULE context switches inline
with SCHED_4BSD.
- Define some new kseq_* functions for manipulating the run queue.
- Add a new kseq member ksq_rslices and ksq_bload. rslices is the sum of
the slices of runnable kses. This will be used for push load balance
decisions. bload is the number of threads blocked waiting on IO.
likely not present under the simulator. If multiple partitions are
present on the virtual disk, then the 'a' partition would be the
most logical choice. Nowadays partitions are GPT based, which would
make the assumption of a disklabel even more questionable. Given
all the possible scenarios, assuming a raw "device" seems best.
- Use atomic subtract to update the global wired pages count. (See
also vm/vm_page.c revision 1.233.)
- Assert that the page queue lock is held in pmap_remove_entry().
- Implement TX power control with hints to code in Linux driver
by Douglas S. J. De Couto <decouto@lcs.mit.edu>
- Update ifmedia support to use ieee80211_rate2media and
ieee80211_media2rate. Note doesn't work with stock ifconfig
since there seems to be an issue with the setmedia code.
"ancontrol -t" works now, before it did nothing.
- Fix spelling error in header.
Rename functions bctv_* to bctv2_* and macros BCTV_* to BCTV2_* for
coexistance of BCTV2 and BCTV3.
Rename CARD_IO_GV to CARD_TO_BCTV2.
Add auto recognition of BCTV3/PCI.
PR: i386/43879
Submitted by: MOROHOSHI Akihiko <moro@remus.dti.ne.jp>
Approved by: roger
MFC after: 6 days
saving and restoring ia32 specific registers when switching
context and ia32 support has not been compiled-in. The primary
reason for this change is that one of the ia32 registers (ar.fcr)
is wrongly marked as invalid by the simulator. Now that we avoid
using the register when possible, usability is improved. The
secundary reason is that it saves us 7 loads and stores.
Note that the PCB will continue to have room for these registers,
irrespective of the IA32 option. There are no benefits that make
it worthwhile.
and instead add platform, firmware and EFI stubs to the loader.
The net effect of this change is that besides a special console and
disk driver, the kernel has no knowledge of the simulator. This has
the following advantages:
o Simulator support is much harder to break,
o It's easier to make use of more feature complete simulators.
This would only need a change in the simulator specific loader,
o Running SMP kernels within the simulator. Note that ski at this
time does not simulate IPIs, so there's no way to start APs.
The platform, firmware and EFI stubs describe the following hardware:
o 4 CPU Itanium,
o 128 MB RAM within the 4GB address space,
o 64 MB RAM above the 4GB address space.
NOTE: The stubs in the skiloader describe a machine that should in
parts be defined by the simulator. Things like processor interrupt
block and AP wakeup vector cannot be choosen at random because they
require interpretation by the simulator. Currently the simulator is
ignorant of this.
This change introduces an unofficial SSC call SSC_SAL_SET_VECTORS
which is ignored by the simulator.
Tested with: ski (version 0.943 for linux)
I'm not convinced there is anything major wrong with the patch but
them's the rules..
I am using my "David's mentor" hat to revert this as he's
offline for a while.
- remove dead code and fix warnings in pmap_zero_page/zero_page_area
- implement
pmap_clear_reference
pmap_ts_referenced
pmap_page_exists_quick
pmap_remove_all
- align pmap_qenter/qremove closer with i386 code
- fix vm_page locking in pmap_new_thread (from benno)
- add new parameter to pmap_clear_bit to return original
pte value
Approved by: benno
using the Rhine's internal shift registers which are designed
for the job. This reduces the amount of time we wait around shifting
bits, and seems to work better with some chips.
Also, provide a workaround for some newer cards which report fake PHYs
at multiple addresses. (As more cards are ID'd, I'm sure this part
of the code will have to be expanded to cover more cases.)
Submitted by: Thomas Nystrom <thn@saeab.se>
MFC after: 1 week
than having change_dir() release the vnode lock on success, hold the
lock so that we can use it later when invoking MAC checks and
VOP_ACCESS() in the chroot() code. Update the comment to reflect
this calling convention. Update callers to unlock the vnode
lock. Correct a typo regarding vnode naming in the MAC case that
crept in via the previous patch applied.
cases: we might multiply vrele() a vnode when certain classes of
failures occur. This appears to stem from earlier Giant/file
descriptor lock pushdown and restructuring.
Submitted by: maxim
under load.
This patch has been tested by Thomas and other for more than a month now,
and all (known) hangs seem to be solved.
Thomas's explanation of the patch:
* Fix the problem with the printing of the RX-error.
* Code from if_fet do better deal with the RX-recovery including a
timeout of the RX-turnoff.
* The call to vr_rxeof before vr_rxeoc have been moved to a point
where the RX-part of the chip is turned off. Otherwise there is a
window where new data could have been written to the buffer chain
before the RX-part is turned off. If this happens the chip will see
a busy rx-buffer. I have no evidence that this have occured but
god knows what the chip will do in this case!
* I have added a timeout of the TX-turnoff. I have checked and in
my 900 MHz system the flags for turnoff (both RX & TX) is seen at
the first check in the loop.
* I could see that I got the VR_ISR_DROPPED interrupt sometimes and
started to thinking about this. I then realized that no recovery is
needed for this case and therefore I only count it as an rxerror
(which was not done before).
* Finally I have changed the FIFO RX threshhold to 128 bytes. When I
did this the VR_ISR_DROPPED interrupt went away. Theory: The chip
will receive a complete frame before it tries to write it out to
memory then the RX threshold is set to store'n'forward. IF the frame
is large AND the next rx frame also is large AND the bus is busy
transfering a TX frame to the TX fifo THEN the second received
frame wont fit in the FIFO and is then dropped. By having the RX
threshold set to 128 the RX fifo is emptied faster.
MFC after: 5 days
Make passing the methods in a cdevsw structure optional.
Move "CANFREE" and "NOGIANT" flags into struct disk instead of the
cdevsw which may or may not be there.
Rename CANFREE to CANDELETE to match BIO_DELETE operation.
Add "OPEN" flag so drivers don't have to provide open/close methods
just to maintain such a flag.
Add temporary stopgap include of <sys/conf.h> to <sys/disk.h> until
the files which have them in the other order are fixed.
Add KASSERTS to make sure we don't get fed too many NULL pointers.
Clear our geom's softc pointer before we wither.
between any pair of values in range 4-96kHz. Thanks to Ken Marks for
discovering there were problems with the previous version.
o Use a non-recursive gcd routine.
interface was left in an active, but not connected, state, which resulted
in data being sent to it and the transmit queue filling up. This happened
because the driver never informed sppp that it shoulkd clean up the
connection. This fix informs sppp that it should clean things up.
The fix was actually developed and tested under -stable, so a short MFC
period seems appropriate, say 2 days.
Contributed by: Ari Suutari <ari.suutari@syncrontech.com>
point of not even compiling for a very long time.
Any effort spent unbreaking them would be better spent perfecting
the ata drivers for PC98, should any issues remain there.
I belive it got here by copy&paste and I see no signs in the source
code that BIO_DELETE was dealt with correctly and can only wonder
what kind of trouble this may have caused.
- Store the OpenFirmware "reg" property in the macio ivars.
- Use a struct to define the structure of a "reg" property entry.
- Discover all memory ranges, not just the first.
- In ata_macio, manage our own range and hand out our own allocations using
bus_space_subregion.
- Fix bus_space_subregion to handle subregions of sparse maps.
ipsec4_process_packet; they happen when a packet is dropped because
an SA acquire is initiated
Submitted by: Doug Ambrisko <ambrisko@verniernetworks.com>
you still don't want to use the two together, but it's ok to have
them in the same kernel (the problem that initiated this bandaid
has long since been fixed)
This should fix the IR(and maybe IT) problem when
the host becames the bus manager.
- rename fw_noderesolve() to fw_noderesolve_eui64() and add
fw_noderesolve_nodeid().
This implicitly removes the need for major numbers, but a number of
drivers still know things they shouldn't need to, and we need to
consider if there are applications which cache major(+minor) gleaned
from stat(2) and rely on it being constant over reboots before we
start assigning random majors.
counterparts to bus_dmamem_alloc() and bus_dmamem_free(). This allows
the caller to specify the size of the allocation instead of it defaulting
to the max_size field of the busdma tag.
This is intended to aid in converting drivers to busdma. Lots of
hardware cannot understand scatter/gather lists, which forces the
driver to copy the i/o buffers to a single contiguous region
before sending it to the hardware. Without these new methods, this
would require a new busdma tag for each operation, or a complex
internal allocator/cache for each driver.
Allocations greater than PAGE_SIZE are rounded up to the next
PAGE_SIZE by contigmalloc(), so this is not suitable for multiple
static allocations that would be better served by a single
fixed-length subdivided allocation.
Reviewed by: jake (sparc64)
sched_runnable() et all.
- Remove some dead code in sched_clock().
- Define two macros KSEQ_SELF() and KSEQ_CPU() for getting the kseq of the
current cpu or some alternate cpu.
- Start introducing kseq_() functions, such as kseq_choose() and kseq_setup().
initialized until after a syncookie was generated. As a result,
all connections resulting from a returned cookie would end up using
a MSS of ~512 bytes. Now larger packets will be used where possible.
MFC after: 5 days
on 900B and 635(A).
Re-add the enhanced PHY access register method again for older chipsets,
they do not seem to work with all old chips.
Reviewed by: phk
MFC after: 7 days
run queue for each cpu.
- Introduce kse stealing into the sched_choose() code. This helps balance
cpus better in cases where process turnover is high. This implementation
is fairly trivial and will likely be only a temporary measure until
something more sophisticated has been written.
kind of pseudofs-based filesystem. Fixes (at least) one problem where
when procfs is mounted mupltiple times, trying to unmount one will often
cause the wrong one to get unmounted, and other problem where mounting
one procfs on top of another caused the kernel to lock up.
Reviewed by: des
- Honor the previous behavior of maxfragpackets = 0 or -1
- Take a better stab at fragment statistics
- Move / correct a comment
Suggested by: maxim@
MFC after: 7 days
the sabtty device to create its description so that they will be
unique for machines with multiple sab chips.
This fixes a panic on machines with an rsc card.
Tested by: obrien (e250)
Properly handle the newer Promise SuperSwap 1000 enclosures.
Print out what kind of enclosure was found in the probe.
Misc cleanups in the enclosure handling code.
Sponsored by: Advanis Inc.
devices.
We use the md_pad[] array and if there are more units than its size the
last returned unit number will be -1, but the number of units returned
is correct.
name of the device that it creates. Update /etc/ttys accordingly.
An alias is created for the old name so that old /etc/ttys will continue to
work, but due to aliases being implemented as symlinks in devfs you cannot
login as root when using the alias device.
Discussed with: grehan
