o Increased number of Rx/Tx descriptors to 256 for 8169 GigEs
because it's hard to push the hardware to the limit with default
64 descriptors.
TSO requires large number of Tx descriptors to pass a full sized
TCP segment(65535 bytes IP packet) to hardware. Previously it
consumed 32 Tx descriptors, assuming MCLBYTES DMA segment size,
to send the TCP segment which means re(4) couldn't queue more
than two full sized IP packets.
For 8139C+ it still uses 64 Rx/Tx descriptors due to its hardware
limitations. With this changes there are (very) small waste of
memory for 8139C+ users but I don't think it would affect 8139C+
users for most cases.
o Various bus_dma(9) fixes.
- The hardware supports DAC so allow 64bit DMA operations.
- Removed BUS_DMA_ALLOC_NOW flag.
- Increased DMA segment size to 4096 from MCLBYTES because TSO
consumes too many descriptors with MCLBYTES DMA segment size.
- Tx/Rx side bus_dmamap_load_mbuf_sg(9) support. With these
changes the code is more readable than previous one and got a
(slightly) better performance as it doesn't need to pass/
decode arguments to/from callback function.
- Removed unnecessary callback function re_dmamap_desc() and
nuked rl_dmaload_arg structure which was used in the callback.
- Additional protection for DMA map load failure. In case of
failure reuse current map instead of returning a bogus DMA
map.
- Deferred DMA map unloading/sync operation for maximum
performance until we really need to load new DMA map. If we
happen to reuse current map(e.g. input error) there is no need
to sync/unload/load again.
- The number of allowable Tx DMA segments for a mbuf chains are
now 32 instead of magic nseg value. If the number of available
Tx descriptors are short enough to send highly fragmented mbuf
chains an optimized re_defrag() is called to collapse mbuf
chains which is supposed to be much faster than m_defrag(9).
re_defrag() was borrowed from ath(4).
- Separated Rx/Tx DMA tag from a common DMA tag such that Rx DMA
tag correctly uses DMA maps that were created with DMA alignment
restriction(8bytes alignments). Tx DMA tag does not have such
alignment limitation.
- Added additional sanity checks for DMA ring map load failure.
- Added additional spare Rx DMA map for graceful handling of Rx
DMA map load failure.
- Fixed misused bus_dmamap_sync(9) and added missing
bus_dmamap_sync(9) in re_encap()/re_txeof()/re_rxeof().
o Enabled TSO again as re(4) have reasonable number of Tx
descriptors.
o Don't touch DMA address of a Tx descriptor in re_txeof(). It's
not needed.
o Fix incorrect update of if_ierrors counter. For Rx buffer
shortage it should update if_qdrops as the buffer is reused.
o Added checks for unsupported H/W revisions and return ENXIO for
these hardwares. This is required to remove resource allocation
code in re_probe as other drivers do in device probe routine.
o Modified descriptor index manipulation macros as it's now possible
to have different number of descriptors for Rx/Tx.
o In re_start, to save a lock operation, use IFQ_DRV_IS_EMPTY before
trying to invoke IFQ_DRV_DEQUEUE. Also don't blindly call re_encap
since we already know the number of available Tx descriptors in
advance.
o Removed RL_TX_DESC_THLD which was used to reserve RL_TX_DESC_THLD
descriptors in Tx path. There is no such a limitation mentioned in
8139C+/8169/8110/8168/8101/8111 datasheet and it seems to work ok
without reserving RL_TX_DESC_THLD descriptors.
o Fix a comment for RL_GTXSTART. The register is 8bits register.
o Added comments for 8169/8139C+ hardware restrictions on descriptors.
o Removed forward declaration for "struct rl_softc", it's not needed.
o Added a new structure rl_txdesc for Tx descriptor managements and
a structure rl_rxdesc for Rx descriptor managements.
o Removed unused member variable rl_intlock in driver softc. There are
still several unused member variables which are supposed to be used
to access hardware statistics counters. But it seems that accessing
hardware counters were not implemented yet.
Ethernet Controller. Multicast filtering wasn't tested and needs more
expore. While I'm here change complex if statements with switch
statement which would improve readability.
Reported by: Abdullah Ibn Hamad Al-Marri < wearabnet AT yahoo DOT ca >
Tested by: Abdullah Ibn Hamad Al-Marri < wearabnet AT yahoo DOT ca >
bumped to 800004 to note the change though userland apps should not be
affected since they use <sys/agpio.h> rather than the headers in
sys/dev/agp.
Discussed with: anholt
Repocopy by: simon
/dev/agpgart and agp_free_res() frees resources like the BAR for the
aperture. Splitting this up lets chipset-specific detach routines
manipulate the aperture during their detach routines without panicing.
MFC after: 1 week
Reviewed by: anholt
VR_STICKHW register would result in unexpected results on these
hardwares. wpaul said the following for the issue.
The vr_attach() routine unconditionally does this for all supported
chips:
/*
* Windows may put the chip in suspend mode when it
* shuts down. Be sure to kick it in the head to wake it
* up again.
*/
VR_CLRBIT(sc, VR_STICKHW, (VR_STICKHW_DS0|VR_STICKHW_DS1));
The problem is, the VR_STICKHW register is not valid on all Rhine
devices. The VT86C100A chip, which is present on the D-Link DFE-530TX
boards, doesn't support power management, and its register space is
only 128 bytes wide. The VR_STICKHW register offset falls outside this
range. This may go unnoticed in most scenarios, but if you happen to have
another PCI device in your system which is assigned the register
space immediately after that of the Rhine, the vr(4) driver will
incorrectly stomp it. In my case, the BIOS on my test board decided
to put the register space for my PRO/100 ethernet board right next
to the Rhine, and the Rhine driver ended up clobbering the IMR register
of the PRO/100 device. (Long story short: the board kept locking up on
boot. Took me the better part of the morning suss out why.)
The strictly correct thing to do would be to check the PCI config space
to make sure the device supports the power management capability and only
write to the VR_STICKHW register if it does.
Instead of inspecting chip revision numbers for the availability of
VR_STICKHW register, check the existence of power management capability
of the hardware as wpaul suggested.
Reported by: wpaul
Suggested by: wpaul
OK'ed by: jhb
previously conditionally acquired Giant based on debug.mpsafenet. As that
has now been removed, they are no longer required. Removing them
significantly simplifies error-handling in the socket layer, eliminated
quite a bit of unwinding of locking in error cases.
While here clean up the now unneeded opt_net.h, which previously was used
for the NET_WITH_GIANT kernel option. Clean up some related gotos for
consistency.
Reviewed by: bz, csjp
Tested by: kris
Approved by: re (kensmith)
Ever since switching to adaptive polling re(4) occasionally spews
watchdog timeouts on systems with MSI capability. This change is
minimal one for supporting MSI and re(4) also needs MSIX support
for RTL8111C in future. Because softc structure of re(4) is shared
with rl(4), rl(4) was touched to use the modified softc.
Reported by: cnst
Tested by: cnst
Approved by: re (kensmith)
This adds a function to agp.c to set the aperture resource ID if it's
not the usual AGP_APBASE. Previously, agp.c had been assuming
AGP_APBASE, which resulted in incorrect agp_info, and contortions by
agp_i810.c to work around it.
This also adds functions to agp.c for default AGP_GET_APERTURE() and
AGP_SET_APERTURE(), which return the aperture resource size and disallow
aperture size changes. Moving to these for our AGP drivers will likely
result in stability improvements. This should fix 855-class aperture
size detection.
Additionally, refuse to attach agp_i810 when some RAM is above 4GB and
the GART can't reference memory that high. This should be very rare.
The correct solution would be bus_dma conversion for agp, which is
beyond the scope of this change. Other AGP drivers could likely use
this change as well.
G33/Q35/Q33 AGP support is also included, but disconnected by default
due to lack of testing.
PR: kern/109724 (855 aperture issue)
Submitted by: FUJIMOTO Kou<fujimoto@j.dendai.ac.jp>
Approved by: re (hrs)
would be 93C46(1Kbit) or 93C56(2Kbit). One of differences between them
is number of address lines required to access the EEPROM. For example,
93C56 EEPROM needs 8 address lines to read/write data. If 93C56
recevied premature end of required number of serial clock(CLK) to set
OP code/address of EEPROM, the result would be unexpected behavior.
Previously it tried to detect 93C46, which requires 6 address lines,
and then assumed it would be 93C56 if read data was not expected
value. However, this approach didn't work in some models/situations
as 93C56 requries 8 address lines to access its data. In order to fix
it, change EEPROM probing order such that 93C56 is detected reliably.
While I'm here change hard-coded address line numbers with defined
constant to enhance readability.
PR: 112710
Approved by: re (mux)
now takes a device_t to be the parent of the bus that is being created.
Most SIMs have been updated with a reasonable argument, but a few exceptions
just pass NULL for now. This argument isn't used yet and the newbus
integration likely won't be ready until after 7.0-RELEASE.
Previously whenever PROMISC mode turned on/off link renegotiation
occurs and it could resulted in network unavailability for serveral
seconds.(Depending on switch STP settings it could last several tens
seconds.)
Reported by: Prokofiev S.P. < proks AT logos DOT uptel DOT net >
Tested by: Prokofiev S.P. < proks AT logos DOT uptel DOT net >
The 6105M and 6102 does not have the DWORD alignment problem, so
don't m_defrag() every packet in the transmit path for those.
More stringent usage of tx-descriptor ring and its flags.
Tested on 6102 and 6105M, other chips may also be able to run
without the m_defrag() but I have neither hardware nor docs to
find out.
Sponsored by: Soekris Engineering
use to synchornize and protect all data objects that are used for that
SIM. Drivers that are not yet MPSAFE register Giant and operate as
usual. RIght now, no drivers are MPSAFE, though a few will be changed
in the coming week as this work settles down.
The driver API has changed, so all CAM drivers will need to be recompiled.
The userland API has not changed, so tools like camcontrol do not need to
be recompiled.
sparc64 GENERIC and the sound device drivers known working on sparc64
to use bus_get_dma_tag() to obtain the parent DMA tag so we can get rid
of the sparc64_root_dma_tag kludge eventually. Except for ath(4), sk(4),
stge(4) and ti(4) these changes are runtime tested (unless I booted up
the wrong kernels again...).
operation as it ran out of free descriptors or if there are too many
segments in the first place, call bus_dmamap_unload() in order to
unload the already loaded segments.
For trying to map the defragmented mbuf (chain) in re_encap() this
introduces re_dma_map_desc() setting arg.rl_maxsegs to 0 as a new
failure mode. Previously we just ignored this case, corrupting our
view of the TX ring.
o In re_txeof():
- Don't clear IFF_DRV_OACTIVE unless there are at least 4 free TX
descriptors. Further down the road re_encap() will bail if there
aren't at least 4 free TX descriptors, causing re_start() to
abort and prepend the dequeued mbuf again so it makes no sense
to pretend we could process mbufs again when in fact we won't.
While at it replace this magic 4 with a macro RL_TX_DESC_THLD
throughout this driver.
- Don't cancel the watchdog timeout as soon as there's at least one
free TX descriptor but instead only if all descriptors have been
handled. It's perfectly normal, especially in the DEVICE_POLLING
case, that re_txeof() is called when only a part of the enqueued
TX descriptors have been handled, causing the watchdog to be
disarmed prematurely.
o In re_encap():
- If m_defrag() fails just drop the packet like other NIC drivers
do. This should only happen when there's a mbuf shortage, in which
case it was possible to end up with an IFQ full of packets which
couldn't be processed as they couldn't be defragmented as they
were taking up all the mbufs themselves. This includes adjusting
re_start() to not trying to prepend the mbuf (chain) if re_encap()
has freed it.
- Remove dupe initialization of members of struct rl_dmaload_arg to
values that didn't change since trying to process the fragmented
mbuf chain.
While at it remove an unused member from struct rl_dmaload_arg.
o In re_start() remove a abandoned, banal comment. The corresponding
code was moved to re_attach() some time ago.
With these changes re(4) now survives one day (until stopped) of
hammering out packets here.
Reviewed by: yongari
MFC after: 2 weeks
only support external PHYs (besides not connectable internal ones
which respond at the usual addresses, but which don't hurt if we
let them show up) and don't wedge when isolating PHYs. Actually,
this change special cases limiting PHYs to Am79C97{3,5,8}, for
which this driver doesn't implement swiching between the internal
and external PHYs, yet, and Am79C971, where isolating the external
PHY (at least in case it's a DP83840A) wedges the chip. Together
with sys/dev/mii/acphy.c rev. 1.21 this adds support for the
100baseFX port of AT-2700 series adaptors, which use two AC101,
one for the copper and one for the fibre port (there might be
variants which only use one PHY though).
- Fix a bug in the previous revision that prevented the address of
the used (external) PHY to be actually recorded.
- Don't bother to set if_mtu to ETHERMTU, ether_ifattach() does that.
MFC after: 1 week
- Use printf() and device_printf() instead of log() in ichsmb(4).
- Create the mutex sooner during ichsmb(4) attach.
- Attach the interrupt handler later during ichsmb(4) attach to avoid
races.
- Don't try to set PCIM_CMD_PORTEN in ichsmb(4) attach as the PCI bus
driver does this already.
- Add locking to alpm(4), amdpm(4), amdsmb(4), intsmb(4), nfsmb(4), and
viapm(4).
- Axe ALPM_SMBIO_BASE_ADDR, it's not really safe to write arbitrary values
into BARs, and the PCI bus layer will allocate resources now if needed.
- Merge intpm(4) and intsmb(4) into just intsmb(4). Previously, intpm(4)
attached to the PCI device and created an intsmb(4) child. Now,
intsmb(4) just attaches to PCI directly.
- Change several intsmb functions to take a softc instead of a device_t
to make things simpler.
- Rename confusing AGP_INTEL_I845_MCHCFG to AGP_INTEL_I845_AGPM.
- Move E7205 and E7505 from i8x5 to i8x0 family. It probably worked
because the actual offset is the same.
In fact, all three families have the bit at the exact same place. Only
differences are name and width of the registers, i.e., NBXCFG (0x50, dword),
RDCR (0x51, byte), AGPM (0x51, byte), MCHCFG (0x50, word) depending on
the family of the chipsets.
