- Add some commented out NICs from i386 GENERIC. Most of them look like they
would work but I'm not sure if they are endian-clean and can't test. There
was a report that sk(4) works on sparc64 but it doesn't look like it would
because it doesn't use busdma.
- Improve some of the descriptions of sparc64 specific devices.
There's no functional change, i.e. no added or deleted uncommented devices or
options, in this commit.
- Chase the split of pcm(4). This unbreaks LINT compiles.
- sc(4) basically works and a lot of its options should be supported.
- Add the creator and ofw_console drivers.
- vinum(4) should work, at least its module was turned on for sparc64 a while
ago.
- Don't build sio(4). Its EBus front-end was removed a while ago and the ISA
one hardly works. Use uart(4) instead, it's not perfect yet but works much
better.
variable. If set to "true" OF_getetheraddr() will now return the unique
MAC address stored in the "local-mac-address" property of the device's
OFW node if present and the host address/system default MAC address if
the node doesn't doesn't have such a property. If set to "false" the
host address will be returned for all devices like before this change.
This brings the behaviour of device drivers for NICs with OFW support/
FCode, i.e. dc(4) for on-board DM9102A on Sun machines, gem(4) and hme(4),
regarding "local-mac-address?" in line with NetBSD and Solaris.
The man pages of the respective drivers will be updated separately to
reflect this change.
- Remove OF_getetheraddr2() which was used as a stopgap in dc(4). Its
functionality is now part of OF_getetheraddr().
subset ("compatible", "device_type", "model" and "name") of the standard
properties in drivers for devices on Open Firmware supported busses. The
standard properties "reg", "interrupts" und "address" are not covered by
this interface because they are only of interest in the respective bridge
code. There's a remaining standard property "status" which is unclear how
to support properly but which also isn't used in FreeBSD at present.
This ofw_bus kobj-interface allows to replace the various (ebus_get_node(),
ofw_pci_get_node(), etc.) and partially inconsistent (central_get_type()
vs. sbus_get_device_type(), etc.) existing IVAR ones with a common one.
This in turn allows to simplify and remove code-duplication in drivers for
devices that can hang off of more than one OFW supported bus.
- Convert the sparc64 Central, EBus, FHC, PCI and SBus bus drivers and the
drivers for their children to use the ofw_bus kobj-interface. The IVAR-
interfaces of the Central, EBus and FHC are entirely replaced by this. The
PCI bus driver used its own kobj-interface and now also uses the ofw_bus
one. The IVARs special to the SBus, e.g. for retrieving the burst size,
remain.
Beware: this causes an ABI-breakage for modules of drivers which used the
IVAR-interfaces, i.e. esp(4), hme(4), isp(4) and uart(4), which need to be
recompiled.
The style-inconsistencies introduced in some of the bus drivers will be
fixed by tmm@ in a generic clean-up of the respective drivers later (he
requested to add the changes in the "new" style).
- Convert the powerpc MacIO bus driver and the drivers for its children to
use the ofw_bus kobj-interface. This invloves removing the IVARs related
to the "reg" property which were unused and a leftover from the NetBSD
origini of the code. There's no ABI-breakage caused by this because none
of these driver are currently built as modules.
There are other powerpc bus drivers which can be converted to the ofw_bus
kobj-interface, e.g. the PCI bus driver, which should be done together
with converting powerpc to use the OFW PCI code from sparc64.
- Make the SBus and FHC front-end of zs(4) and the sparc64 eeprom(4) take
advantage of the ofw_bus kobj-interface and simplify them a bit.
Reviewed by: grehan, tmm
Approved by: re (scottl)
Discussed with: tmm
Tested with: Sun AX1105, AXe, Ultra 2, Ultra 60; PPC cross-build on i386
to allow dumping per-thread machine specific notes. On ia64 we use this
function to flush the dirty registers onto the backingstore before we
write out the PRSTATUS notes.
Tested on: alpha, amd64, i386, ia64 & sparc64
Not tested on: arm, powerpc
Implement the protection check required by the pmap_extract_and_hold()
specification.
Remove the acquisition and release of Giant from pmap_extract_and_hold() and
pmap_protect().
Many thanks to Ken Smith for resolving a sparc64-specific initialization
problem in my original patch.
Tested by: kensmith@
being defined, define and use a new MD macro, cpu_spinwait(). It only
expands to something on i386 and amd64, so the compiled code should be
identical.
Name of the macro found by: jhb
Reviewed by: jhb
their own directory and module, leaving the MD parts in the MD
area (the MD parts _are_ part of the modules). /dev/mem and /dev/io
are now loadable modules, thus taking us one step further towards
a kernel created entirely out of modules. Of course, there is nothing
preventing the kernel from having these statically compiled.
those architectures without pmap locking.
- Eliminate the acquisition and release of Giant from vm_map_protect().
(Translation: mprotect(2) runs to completion without touching Giant on
alpha, amd64, i386 and ia64.)
dereference curthread. It is called only from critical_{enter,exit}(),
which already dereferences curthread. This doesn't seem to affect SMP
performance in my benchmarks, but improves MySQL transaction throughput
by about 1% on UP on my Xeon.
Head nodding: jhb, bmilekic
the thread ID and call db_trace_thread().
Since arm has all the logic in db_stack_trace_cmd(), rename the
new DB_COMMAND function to db_stack_trace to avoid conflicts on
arm.
While here, have db_stack_trace parse its own arguments so that
we can use a more natural radix for IDs. If the ID is not a thread
ID, or more precisely when no thread exists with the ID, try if
there's a process with that ID and return the first thread in it.
This makes it easier to print stack traces from the ps output.
requested by: rwatson@
tested on: amd64, i386, ia64
pmap_protect() and pmap_remove(). In general, they require the lock in
order to modify a page's pv list or flags. In some cases, however,
pmap_protect() can avoid acquiring the lock.
Most of the changes are a direct result of adding thread awareness.
Typically, DDB_REGS is gone. All registers are taken from the
trapframe and backtraces use the PCB based contexts. DDB_REGS was
defined to be a trapframe on all platforms anyway.
Thread awareness introduces the following new commands:
thread X switch to thread X (where X is the TID),
show threads list all threads.
The backtrace code has been made more flexible so that one can
create backtraces for any thread by giving the thread ID as an
argument to trace.
With this change, ia64 has support for breakpoints.
o Make debugging code conditional upon KDB instead of DDB.
o Call kdb_enter() instead of Debugger().
o Remove implementation of Debugger().
o Check kdb_active instead of db_active.
o Call kdb_trap() according to the new world order.
a PCB from a trapframe for purposes of unwinding the stack. The PCB
is used as the thread context and all but the thread that entered the
debugger has a valid PCB.
This function can also be used to create a context for the threads
running on the CPUs that have been stopped when the debugger got
entered. This however is not done at the time of this commit.
in which multiple (presumably different) debugger backends can be
configured and which provides basic services to those backends.
Besides providing services to backends, it also serves as the single
point of contact for any and all code that wants to make use of the
debugger functions, such as entering the debugger or handling of the
alternate break sequence. For this purpose, the frontend has been
made non-optional.
All debugger requests are forwarded or handed over to the current
backend, if applicable. Selection of the current backend is done by
the debug.kdb.current sysctl. A list of configured backends can be
obtained with the debug.kdb.available sysctl. One can enter the
debugger by writing to the debug.kdb.enter sysctl.
backend improves over the old GDB support in the following ways:
o Unified implementation with minimal MD code.
o A simple interface for devices to register themselves as debug
ports, ala consoles.
o Compression by using run-length encoding.
o Implements GDB threading support.
than as one-off hacks in various other parts of the kernel:
- Add a function maybe_preempt() that is called from sched_add() to
determine if a thread about to be added to a run queue should be
preempted to directly. If it is not safe to preempt or if the new
thread does not have a high enough priority, then the function returns
false and sched_add() adds the thread to the run queue. If the thread
should be preempted to but the current thread is in a nested critical
section, then the flag TDF_OWEPREEMPT is set and the thread is added
to the run queue. Otherwise, mi_switch() is called immediately and the
thread is never added to the run queue since it is switch to directly.
When exiting an outermost critical section, if TDF_OWEPREEMPT is set,
then clear it and call mi_switch() to perform the deferred preemption.
- Remove explicit preemption from ithread_schedule() as calling
setrunqueue() now does all the correct work. This also removes the
do_switch argument from ithread_schedule().
- Do not use the manual preemption code in mtx_unlock if the architecture
supports native preemption.
- Don't call mi_switch() in a loop during shutdown to give ithreads a
chance to run if the architecture supports native preemption since
the ithreads will just preempt DELAY().
- Don't call mi_switch() from the page zeroing idle thread for
architectures that support native preemption as it is unnecessary.
- Native preemption is enabled on the same archs that supported ithread
preemption, namely alpha, i386, and amd64.
This change should largely be a NOP for the default case as committed
except that we will do fewer context switches in a few cases and will
avoid the run queues completely when preempting.
Approved by: scottl (with his re@ hat)
than a a stack-limited list. This removes the artifical limit on s/g list
size.
cvs: ----------------------------------------------------------------------
Ultra2 users may want to set OFWCONS_POLL_HZ to a value of '20'.
I have left default value at '4' as higher values can consume a more
than is acceptable amount of CPU, and we don't have a consensus yet
what is an optimal value.
Submitted by: Pyun YongHyeon <yongari@kt-is.co.kr>
its primary use is for the FEPS/FAS366 SCSI found in Sun Ultra 1e and 2
machines. Once the pci front-end is ported, this driver can replace the
amd(4) driver.
The code as-is is fairly stable. I've disabled tagged-queueing until I can
figure out a corruption bug related to it. I'm importing it now so that
people with these machines can (finally) stop netbooting and report bugs
before 5.3.
mbuma is an Mbuf & Cluster allocator built on top of a number of
extensions to the UMA framework, all included herein.
Extensions to UMA worth noting:
- Better layering between slab <-> zone caches; introduce
Keg structure which splits off slab cache away from the
zone structure and allows multiple zones to be stacked
on top of a single Keg (single type of slab cache);
perhaps we should look into defining a subset API on
top of the Keg for special use by malloc(9),
for example.
- UMA_ZONE_REFCNT zones can now be added, and reference
counters automagically allocated for them within the end
of the associated slab structures. uma_find_refcnt()
does a kextract to fetch the slab struct reference from
the underlying page, and lookup the corresponding refcnt.
mbuma things worth noting:
- integrates mbuf & cluster allocations with extended UMA
and provides caches for commonly-allocated items; defines
several zones (two primary, one secondary) and two kegs.
- change up certain code paths that always used to do:
m_get() + m_clget() to instead just use m_getcl() and
try to take advantage of the newly defined secondary
Packet zone.
- netstat(1) and systat(1) quickly hacked up to do basic
stat reporting but additional stats work needs to be
done once some other details within UMA have been taken
care of and it becomes clearer to how stats will work
within the modified framework.
From the user perspective, one implication is that the
NMBCLUSTERS compile-time option is no longer used. The
maximum number of clusters is still capped off according
to maxusers, but it can be made unlimited by setting
the kern.ipc.nmbclusters boot-time tunable to zero.
Work should be done to write an appropriate sysctl
handler allowing dynamic tuning of kern.ipc.nmbclusters
at runtime.
Additional things worth noting/known issues (READ):
- One report of 'ips' (ServeRAID) driver acting really
slow in conjunction with mbuma. Need more data.
Latest report is that ips is equally sucking with
and without mbuma.
- Giant leak in NFS code sometimes occurs, can't
reproduce but currently analyzing; brueffer is
able to reproduce but THIS IS NOT an mbuma-specific
problem and currently occurs even WITHOUT mbuma.
- Issues in network locking: there is at least one
code path in the rip code where one or more locks
are acquired and we end up in m_prepend() with
M_WAITOK, which causes WITNESS to whine from within
UMA. Current temporary solution: force all UMA
allocations to be M_NOWAIT from within UMA for now
to avoid deadlocks unless WITNESS is defined and we
can determine with certainty that we're not holding
any locks when we're M_WAITOK.
- I've seen at least one weird socketbuffer empty-but-
mbuf-still-attached panic. I don't believe this
to be related to mbuma but please keep your eyes
open, turn on debugging, and capture crash dumps.
This change removes more code than it adds.
A paper is available detailing the change and considering
various performance issues, it was presented at BSDCan2004:
http://www.unixdaemons.com/~bmilekic/netbuf_bmilekic.pdf
Please read the paper for Future Work and implementation
details, as well as credits.
Testing and Debugging:
rwatson,
brueffer,
Ketrien I. Saihr-Kesenchedra,
...
Reviewed by: Lots of people (for different parts)
struct vmspace is freed from cpu_sched_exit() to pmap_release().
This has the advantage of being able to rely on MI code to decide
when a free should occur, instead of having to inspect the reference
count ourselves.
At the same time, turn the per-CPU vmspace pointer into a pmap pointer,
so that pmap_release() can deal with pmaps exclusively.
Reviewed (and embrassing bug spotted) by: jake
to <sys/gmon.h>. Cleaned them up a little by not attempting to ifdef
for incomplete and out of date support for GUPROF in userland, as in
the sparc64 version.
elf_reloc() backends for two reasons. First, to support the possibility
of there being two elf linkers in the kernel (eg: amd64), and second, to
pass the relocbase explicitly (for relocating .o format kld files).
"options OFW_NEWPCI").
This is a bit overdue, the new sparc64 OFW PCI code which is
meant to replace the old one is in place for 10 months and
enabled by default in GENERIC for 8 months. FreeBSD 5.2 and
5.2.1 also shipped with the new code enabled by default.
- Some minor clean-up, e.g. remove functions that encapsulated
the #ifdefs for OFW_NEWPCI, remove unused resp. no longer
required includes, etc.
Approved by: tmm, no objections on freebsd-sparc64
and type for printing info about the device that didn't probe from child, not
parent.
This fixes a panic on systems where not yet supported devices hang off of the
nexus, e.g. on E450.
Reported by: joerg
- Remove second license, the first was not that different and should be
fine.
- Add nexus_attach(), and do not perform its task in nexus_probe() any
more.
- Remove nexus_write_ivar(), since it was quite pointless.
- Remove superfluous devinfo members.
- Clean up some comments, minor style issues and prototypes.
bridges, the EBus bridge has resource ranges it claims exclusively to
map its children into in its BARs. Hence, we need to allocate these
completely and manage them for the children, instead of just passing
allocations through to the PCI layer as we did before.
While being there, split ebus_probe(), which did also contain code
normally belonging into the attach method, into ebus_probe() and
ebus_attach(), and perform some minor cleanups.
- Fix some comments; remove numerous superfluous or outdated ones.
- Correctly pass on the requesting device when handing requests up
to the parent bus.
- Use the complete device name, including unit number, to build the
IOMMU instance name.
- Inline a function that was only used once, and was trivial.
phandle_t. Since both are typedefed to unsigned int, this is more
or less cosmetic.
- Fix the code that determines whether a creator instance was used
for firmware output (and should not be blanked on initialization).
Since r1.2 of dev/fb/creator.c, this consisted comparing a handle of
an instance of a package with a handle of the package itself.
Use the test from r1.1, which utilizes OF_instance_to_package().
Submitted by: Marius Strobl <marius@alchemy.franken.de>
iommu_dvma_vallocseg(), which I botched in r1.32. This bug could
cause an endless loop when a map was loaded and DVMA was scarce,
or that map had a stringent alignment or boundary.
Report and additional testing: Marius Strobl <marius@alchemy.franken.de>
in cpu_fork(). This prevents the stack tracer from running past the
end of the stack (only the pc is checked in that case), which became
fatal when db_print_backtrace() was introduced and called outside
of ddb.
Additional testing: kris
implementation could be characterized as a hybrid of the amd64 and i386
implementations. Specifically, the direct virtual-to-physical mapping is
used if possible and sf_buf_alloc() is used if the direct map cannot.
level of abstraction for any and all CPU mask and CPU bitmap variables
so that platforms have the ability to break free from the hard limit
of 32 CPUs, simply because we don't have more bits in an u_int. Note
that the type is not supposed to solve massive parallelism, where
the number of CPUs can be larger than the width of the widest integral
type. As such, cpumask_t is not supposed to be a compound type. If
such would be necessary in the future, we can deal with the issues
then and there. For now, it can be assumed that the type is integral
and unsigned.
With this commit, all MD definitions start off as u_int. This allows
us to phase-in cpumask_t at our leasure without breaking anything.
Once cpumask_t is used consistently, platforms can switch to wider
(or smaller) types if such would be beneficial (or not; whatever :-)
Compile-tested on: i386
dependent function by the same name and a machine-independent function,
sf_buf_mext(). Aside from the virtue of making more of the code machine-
independent, this change also makes the interface more logical. Before,
sf_buf_free() did more than simply undo an sf_buf_alloc(); it also
unwired and if necessary freed the page. That is now the purpose of
sf_buf_mext(). Thus, sf_buf_alloc() and sf_buf_free() can now be used
as a general-purpose emphemeral map cache.
only. This is a MAJOR incompatible change for the sparc64 platform,
but will not effect FreeBSD on other architectures.
Reviewed by: imp for UPDATING, freebsd-sparc for the change itself.
ever since alpha/alpha/pmap.c revision 1.81 introduced the list allpmaps,
there has been no reason for having this function on Alpha. Briefly,
when pmap_growkernel() relied upon the list of all processes to find and
update the various pmaps to reflect a growth in the kernel's valid
address space, pmap_init2() served to avoid a race between pmap
initialization and pmap_growkernel(). Specifically, pmap_pinit2() was
responsible for initializing the kernel portions of the pmap and
pmap_pinit2() was called after the process structure contained a pointer
to the new pmap for use by pmap_growkernel(). Thus, an update to the
kernel's address space might be applied to the new pmap unnecessarily,
but an update would never be lost.
Introduce d_version field in struct cdevsw, this must always be
initialized to D_VERSION.
Flip sense of D_NOGIANT flag to D_NEEDGIANT, this involves removing
four D_NOGIANT flags and adding 145 D_NEEDGIANT flags.
at it, use the ANSI C generic pointer type for the second argument,
thus matching the documentation.
Remove the now extraneous (and now conflicting) function declarations
in various libc sources. Remove now unnecessary casts.
Reviewed by: bde
MAC address in the EEPROM, and we need to get it from OpenFirmware.
This isn't very pretty but time is lacking to do this in a better
way this near 5.2-RELEASE. This is a RELENG_5_2 candidate.
Original version by: Marius Strobl <marius@alchemy.franken.de>
Tested by: Pete Bentley <pete@sorted.org>
Reviewed by: jake
is useless for threaded programs, multiple threads can not share same
stack.
The alternative signal stack is private for thread, no lock is needed,
the orignal P_ALTSTACK is now moved into td_pflags and renamed to
TDP_ALTSTACK.
For single thread or Linux clone() based threaded program, there is no
semantic changed, because those programs only have one kernel thread
in every process.
Reviewed by: deischen, dfr
1) mp_maxid is a valid FreeBSD CPU ID in the range 0 .. MAXCPU - 1.
2) For all active CPUs in the system, PCPU_GET(cpuid) <= mp_maxid.
Approved by: re (scottl)
Tested on: i386, amd64, alpha
very early (SI_SUB_TUNABLES - 1) and is responsible for setting mp_maxid.
cpu_mp_probe() is now called at SI_SUB_CPU and determines if SMP is
actually present and sets mp_ncpus and all_cpus. Splitting these up
allows an architecture to probe CPUs later than SI_SUB_TUNABLES by just
setting mp_maxid to MAXCPU in cpu_mp_setmaxid(). This could allow the
CPU probing code to live in a module, for example, since modules
sysinit's in modules cannot be invoked prior to SI_SUB_KLD. This is
needed to re-enable the ACPI module on i386.
- For the alpha SMP probing code, use LOCATE_PCS() instead of duplicating
its contents in a few places. Also, add a smp_cpu_enabled() function
to avoid duplicating some code. There is room for further code
reduction later since much of this code is also present in cpu_mp_start().
- All archs besides i386 still set mp_maxid to the same values they set it
to before this change. i386 now sets mp_maxid to MAXCPU.
Tested on: alpha, amd64, i386, ia64, sparc64
Approved by: re (scottl)
physical mapping.
- Move the sf_buf API to its own header file; make struct sf_buf's
definition machine dependent. In this commit, we remove an
unnecessary field from struct sf_buf on the alpha, amd64, and ia64.
Ultimately, we may eliminate struct sf_buf on those architecures
except as an opaque pointer that references a vm page.
cache after a data access error we must discard all cache lines. When
disabled existing cache lines are not invalidated by stores to memory, so
we risk reading stale data that was cached before the data access error if
we don't flush them. This is especially fatal when the memory involved
is the active part of the kernel or user stack. For good measure we also
flush the instruction cache.
This fixes random crashes when the X server probes the PCI bus through
/dev/pci.
Since all callers either passed 0 or 1 for clear_ret, define bit 0 in
the flags for use as clear_ret. Reserve bits 1, 2 and 3 for use by MI
code for possible (but unlikely) future use. The remaining bits are for
use by MD code.
This change is triggered by a need on ia64 to have another knob for
get_mcontext().
A small helper function pmap_is_prefaultable() is added. This function
encapsulate the few lines of pmap_prefault() that actually vary from
machine to machine. Note: pmap_is_prefaultable() and pmap_mincore() have
much in common. Going forward, it's worth considering their merger.
quantities on every other architecture.) This change is required in order
to move pmap_prefault() out of the pmap and into the machine-independent
layer.
evaluating them at compile time rather than at run time. As for x86
and amd64, this requires GCC and it's enabled only if __OPTIMIZE__ is
defined (ie, if at least -O is used).
Reviewed by: jake
systems where the data/stack/etc limits are too big for a 32 bit process.
Move the 5 or so identical instances of ELF_RTLD_ADDR() into imgact_elf.c.
Supply an ia32_fixlimits function. Export the clip/default values to
sysctl under the compat.ia32 heirarchy.
Have mmap(0, ...) respect the current p->p_limits[RLIMIT_DATA].rlim_max
value rather than the sysctl tweakable variable. This allows mmap to
place mappings at sensible locations when limits have been reduced.
Have the imgact_elf.c ld-elf.so.1 placement algorithm use the same
method as mmap(0, ...) now does.
Note that we cannot remove all references to the sysctl tweakable
maxdsiz etc variables because /etc/login.conf specifies a datasize
of 'unlimited'. And that causes exec etc to fail since it can no
longer find space to mmap things.
atomically extracts and holds the physical page that is associated with the
given pmap and virtual address. Such a function is needed to make the
memory mapping optimizations used by, for example, pipes and raw disk I/O
MP-safe.
Reviewed by: tegge
rl(4) driver and put it in a new re(4) driver. The re(4) driver shares
the if_rlreg.h file with rl(4) but is a separate module. (Ultimately
I may change this. For now, it's convenient.)
rl(4) has been modified so that it will never attach to an 8139C+
chip, leaving it to re(4) instead. Only re(4) has the PCI IDs to
match the 8169/8169S/8110S gigE chips. if_re.c contains the same
basic code that was originally bolted onto if_rl.c, with the
following updates:
- Added support for jumbo frames. Currently, there seems to be
a limit of approximately 6200 bytes for jumbo frames on transmit.
(This was determined via experimentation.) The 8169S/8110S chips
apparently are limited to 7.5K frames on transmit. This may require
some more work, though the framework to handle jumbo frames on RX
is in place: the re_rxeof() routine will gather up frames than span
multiple 2K clusters into a single mbuf list.
- Fixed bug in re_txeof(): if we reap some of the TX buffers,
but there are still some pending, re-arm the timer before exiting
re_txeof() so that another timeout interrupt will be generated, just
in case re_start() doesn't do it for us.
- Handle the 'link state changed' interrupt
- Fix a detach bug. If re(4) is loaded as a module, and you do
tcpdump -i re0, then you do 'kldunload if_re,' the system will
panic after a few seconds. This happens because ether_ifdetach()
ends up calling the BPF detach code, which notices the interface
is in promiscuous mode and tries to switch promisc mode off while
detaching the BPF listner. This ultimately results in a call
to re_ioctl() (due to SIOCSIFFLAGS), which in turn calls re_init()
to handle the IFF_PROMISC flag change. Unfortunately, calling re_init()
here turns the chip back on and restarts the 1-second timeout loop
that drives re_tick(). By the time the timeout fires, if_re.ko
has been unloaded, which results in a call to invalid code and
blows up the system.
To fix this, I cleared the IFF_UP flag before calling ether_ifdetach(),
which stops the ioctl routine from trying to reset the chip.
- Modified comments in re_rxeof() relating to the difference in
RX descriptor status bit layout between the 8139C+ and the gigE
chips. The layout is different because the frame length field
was expanded from 12 bits to 13, and they got rid of one of the
status bits to make room.
- Add diagnostic code (re_diag()) to test for the case where a user
has installed a broken 32-bit 8169 PCI NIC in a 64-bit slot. Some
NICs have the REQ64# and ACK64# lines connected even though the
board is 32-bit only (in this case, they should be pulled high).
This fools the chip into doing 64-bit DMA transfers even though
there is no 64-bit data path. To detect this, re_diag() puts the
chip into digital loopback mode and sets the receiver to promiscuous
mode, then initiates a single 64-byte packet transmission. The
frame is echoed back to the host, and if the frame contents are
intact, we know DMA is working correctly, otherwise we complain
loudly on the console and abort the device attach. (At the moment,
I don't know of any way to work around the problem other than
physically modifying the board, so until/unless I can think of a
software workaround, this will have do to.)
- Created re(4) man page
- Modified rlphy.c to allow re(4) to attach as well as rl(4).
Note that this code works for the sample 8169/Marvell 88E1000 NIC
that I have, but probably won't work for the 8169S/8110S chips.
RealTek has sent me some sample NICs, but they haven't arrived yet.
I will probably need to add an rlgphy driver to handle the on-board
PHY in the 8169S/8110S (it needs special DSP initialization).
a correctable DMA error. Failing to do so can cause the error interrupt
to be triggered over and over again.
- Clean up the comments for UEAFSR_* constants, fix a typo (UEAFSR_BLK is
(1 << 23), not (1 << 22)), and add two more. Also, add similar constants
for the CE AFSR bits.
address of the device identified by its phandle_t by traversing OFW's
device tree. The space and address returned by this function can
subsequently be passed to sparc64_fake_bustag() to construct a valid
tag and handle for use by the newbus I/O functions.
Use of this function is expected to be limited to pre-newbus access to
devices, such as consoles and keyboards.
Partially obtained from: tmm
Reviewed by: jake, jmg, tmm
SBus testing made possible by: jake
Tested with: LINT
sockets into machine-dependent files. The rationale for this
migration is illustrated by the modified amd64 allocator. It uses the
amd64's direct map to avoid emphemeral mappings in the kernel's
address space. On an SMP, the emphemeral mappings result in an IPI
for TLB shootdown for each transmitted page. Yuck.
Maintainers of other 64-bit platforms with direct maps should be able
to use the amd64 allocator as a reference implementation.
bus tag is to allow bus space accesses prior to having newbus
fully initialized, such as would be the case for console drivers.
Since barriers are a fundamental part of bus space accesses, not
allowing them on fake tags would defeat the purpose of these tags.
We use the barrier function normally associated with nexus. This
is the barrier used when subordinates haven't defined a barrier
themselves.
These are fixed resolution and operate only in pixel mode so they present
a challenge to syscons (square peg, round hole, etc, etc). The driver
provides a video driver interface for syscons and a separate character
device for X to mmap. Wherever possible the creator's accelarated graphics
functions are used so text mode is very fast.
Based roughly on the openbsd driver.
that caused a 3-4 times slow down in performance.
(the primary Sparc64 developers are all using OFW_NEWPCI already, so it is
the best code path for users)
prototypes of cpu_halt(), cpu_reset() and swi_vm() from md_var.h to
cpu.h. This affects db_command.c and kern_shutdown.c.
ia64: move all MD prototypes from cpu.h to md_var.h. This affects
madt.c, interrupt.c and mp_machdep.c. Remove is_physical_memory().
It's not used (vm_machdep.c).
alpha: the MD prototypes have been left in cpu.h with a comment
that they should be there. Moving them is left for later. It was
expected that the impact would be significant enough to be done in
a seperate commit.
powerpc: MD prototypes left in cpu.h. Comment added.
Suggested by: bde
Tested with: make universe (pc98 incomplete)
set in cpu_critical_fork_exit() anymore.
- As far as I can tell, cpu_thread_link() has never been used, not even
when it was originally added, so remove it.
tsb_foreach(), 0 signals to terminate the tsb traversal, so when
tsb_foreach() was used in pmap_protect() (which only happens when
the area to be protected is larger than PMAP_TSB_THRESH = 16MB), only
the first tsb entry in the specified range would be protected.
Reported by: Andrew Belashov <bel@orel.ru>
memory in bus_dmamem_alloc(). This is possible now that
contigmalloc() supports the M_ZERO flag.
- Remove the locking of Giant around calls to contigmalloc() since
contigmalloc() now grabs Giant itself.
code from i386. The code has a slight bogon that interrupts are counted
twice. Once on the ithread dispatch and once on the dispatch for the vector
vmstat -i and systat -vm now contains interrupt counts.
Reviewed by: jake
without Giant held.
A quick outline of the locking strategy:
Since all IOMMUs are synchronized, there is a single lock, iommu_mtx,
which protects the hardware registers (where needed) and the global and
per-IOMMU software states. As soon as the IOMMUs are divorced, each struct
iommu_state will have its own mutex (and the remaining global state
will be moved into the struct).
The dvma rman has its own internal mutex; the TSB slots may only be
accessed by the owner of the corresponding resource, so neither needs
extra protection.
Since there is a second access path to maps via LRU queues, the consumer-
provided locking is not sufficient; therefore, each map which is on a
queue is additionally protected by iommu_mtx (in part, there is one
member which only the map owner may access). Each map on a queue may
be accessed and removed from or repositioned in a queue in any context as
long as the lock is held; only the owner may insert a map.
To reduce lock contention, some bus_dma functions remove the map from
the queue temporarily (on behalf of the map owner) for some operations and
reinsert it when they are done. Shorter operations and operations which are
not done on behalf of the lock owner are completely covered by the lock.
To facilitate the locking, reorganize the streaming buffer handling;
while being there, fix an old oversight which would cause the streaming
buffer to always be flushed, regardless of whether streaming was enabled
in the TSB entry. The streaming buffer is still disabled for now, since
there are a number of drivers which lack critical bus_dmamp_sync() calls.
Additional testing by: jake
order to avoid the overhead of later page faults. In general, it
implements two cases: one for vnode-backed objects and one for
device-backed objects. Only the device-backed case is really
machine-dependent, belonging in the pmap.
This commit moves the vnode-backed case into the (relatively) new
function vm_map_pmap_enter(). On amd64 and i386, this commit only
amounts to code rearrangement. On alpha and ia64, the new machine
independent (MI) implementation of the vnode case is smaller and more
efficient than their pmap-based implementations. (The MI
implementation takes advantage of the fact that objects in -CURRENT
are ordered collections of pages.) On sparc64, pmap_object_init_pt()
hadn't (yet) been implemented.
Add two new arguments to bus_dma_tag_create(): lockfunc and lockfuncarg.
Lockfunc allows a driver to provide a function for managing its locking
semantics while using busdma. At the moment, this is used for the
asynchronous busdma_swi and callback mechanism. Two lockfunc implementations
are provided: busdma_lock_mutex() performs standard mutex operations on the
mutex that is specified from lockfuncarg. dftl_lock() is a panic
implementation and is defaulted to when NULL, NULL are passed to
bus_dma_tag_create(). The only time that NULL, NULL should ever be used is
when the driver ensures that bus_dmamap_load() will not be deferred.
Drivers that do not provide their own locking can pass
busdma_lock_mutex,&Giant args in order to preserve the former behaviour.
sparc64 and powerpc do not provide real busdma_swi functions, so this is
largely a noop on those platforms. The busdma_swi on is64 is not properly
locked yet, so warnings will be emitted on this platform when busdma
callback deferrals happen.
If anyone gets panics or warnings from dflt_lock() being called, please
let me know right away.
Reviewed by: tmm, gibbs
with a comment describing it's advantages and the implication of
changing it. While being there, fix a typo in NOTES.
The option is not enabled in NOTES for now since large portions of code
are conditional on it being disabled, too.
for now. It introduces a OFW PCI bus driver and a generic OFW PCI-PCI
bridge driver. By utilizing these, the PCI handling is much more elegant
now.
The advantages of the new approach are:
- Device enumeration should hopefully be more like on Solaris now,
so unit numbers should match what's printed on the box more
closely.
- Real interrupt routing is implemented now, so cardbus bridges
etc. have at least a chance to work.
- The quirk tables are gone and have been replaced by (hopefully
sufficient) heuristics.
- Much cleaner code.
There was also a report that previously bogus interrupt assignments
are fixed now, which can be attributed to the new heuristics.
A pitfall, and the reason why this is not the default yet, is that
it changes device enumeration, as mentioned above, which can make
it necessary to change the system configuration if more than one
unit of a device type is present (on a system with two hme cars,
for example, it is possible that hme0 becomes hme1 and vice versa
after enabling the option). Systems with multiple disk controllers
may need to be booted into single user (and require manual specification
of the root file system on boot) to adjust the fstab.
Nevertheless, I would like to encourage users to use this option,
so that it can be made the default soon.
In detail, the changes are:
- Introduce an OFW PCI bus driver; it inherits most methods from the
generic PCI bus driver, but uses the firmware for enumeration,
performs additional initialization for devices and firmware-specific
interrupt routing. It also implements an OFW-specific method to allow
child devices to get their firmware nodes.
- Introduce an OFW PCI-PCI bridge driver; again, it inherits most
of the generic PCI-PCI bridge driver; it has it's own method for
interrupt routing, as well as some sparc64-specific methods (one to
get the node again, and one to adjust the bridge bus range, since
we need to reenumerate all PCI buses).
- Convert the apb driver to the new way of handling things.
- Provide a common framework for OFW bridge drivers, used be the two
drivers above.
- Provide a small common framework for interrupt routing (for all
bridge types).
- Convert the psycho driver to the new framework; this gets rid of a
bunch of old kludges in pci_read_config(), and the whole
preinitialization (ofw_pci_init()).
- Convert the ISA MD part and the EBus driver to the new way
interrupts and nodes are handled.
- Introduce types for firmware interrupt properties.
- Rename the old sparcbus_if to ofw_pci_if by repo copy (it is only
required for PCI), and move it to a more correct location (new
support methodsx were also added, and an old one was deprecated).
- Fix a bunch of minor bugs, perform some cleanups.
In some cases, I introduced some minor code duplication to keep the
new code clean, in hopes that the old code will be unifdef'ed soon.
Reviewed in part by: imp
Tested by: jake, Marius Strobl <marius@alchemy.franken.de>,
Sergey Mokryshev <mokr@mokr.net>,
Chris Jackman <cjackNOSPAM@klatsch.org>
Info on u30 firmware provided by: kris
implementation of a largely MI pmap_object_init_pt() for vnode-backed
objects. pmap_enter_quick() is implemented via pmap_enter() on sparc64
and powerpc.
- Correct a mismatch between pmap_object_init_pt()'s prototype and its
various implementations. (I plan to keep pmap_object_init_pt() as
the MD hook for device-backed objects on i386 and amd64.)
- Correct an error in ia64's pmap_enter_quick() and adjust its interface
to match the other versions. Discussed with: marcel
1.) Handle maximum segment sizes which are smaller than the IOMMU page
size by splitting up pages across multiple segments if needed; this case
was previously unimplemented, and would cause panics.
2.) KASSERT that the physical address is in range; remove a KASSERT that
has become pointless.
3.) Add a comment describing what remains to be fixed in the IOMMU code;
I plan to address these issues soon.
Desired by: dwhite (1)
data access errors when trying to read/write to non-existant PCI devices.
fix the psycho bridge to use peek for probing devices. This no longer
fakes it if the OFW node doesn't exist (and the reg == 0).
Reviewed by: jake, tmm
- Don't require all receivers of ipis to wait for all other receivers,
only that the sender wait for all receivers. This should reduce the
amount of time spent with interrupts disabled, which may be a cause
of ipi timeouts.
Discussed with: tmm
- Move prototypes for sparc64-specific helper functions from bus.h to
bus_private.h
- Move the method pointers from struct bus_dma_tag into a separate
structure; this saves some memory, and allows to use a single method
table for each busdma backend, so that the bus drivers need no longer
be changed if the methods tables need to be modified.
- Remove the hierarchical tag method lookup. It was never really useful,
since the layering is fixed, and the current implementations do not
need to call into parent implementations anyway. Each tag inherits
its method table pointer and cookie from the parent (or the root tag)
now, and the method wrapper macros directly use the method table
of the tag.
- Add a method table to the non-IOMMU backend, remove unnecessary
prototypes, remove the extra parent tag argument.
- Rename sparc64_dmamem_alloc_map() and sparc64_dmamem_free_map() to
sparc64_dma_alloc_map() and sparc64_dma_free_map(), move them to a
better place and use them for all map allocations and deallocations.
- Add a method table to the iommu backend, and staticize functions,
remove the extra parent tag argument.
- Change the psycho and sbus drivers to just set cookie and method table
in the root tag.
- Miscellaneous small fixes.
- Add vm page queue locking in certain places that are only needed on
sparc64.
This should make pmap_qenter and pmap_qremove MP-safe.
Discussed with: alc
to the machine-independent parts of the VM. At the same time, this
introduces vm object locking for the non-i386 platforms.
Two details:
1. KSTACK_GUARD has been removed in favor of KSTACK_GUARD_PAGES. The
different machine-dependent implementations used various combinations
of KSTACK_GUARD and KSTACK_GUARD_PAGES. To disable guard page, set
KSTACK_GUARD_PAGES to 0.
2. Remove the (unnecessary) clearing of PG_ZERO in vm_thread_new. In
5.x, (but not 4.x,) PG_ZERO can only be set if VM_ALLOC_ZERO is passed
to vm_page_alloc() or vm_page_grab().
we were passing in a void* representing the PCB of the parent thread.
Now we pass a pointer to the parent thread itself.
The prime reason for this change is to allow cpu_set_upcall() to copy
(parts of) the trapframe instead of having it done in MI code in each
caller of cpu_set_upcall(). Copying the trapframe cannot always be
done with a simply bcopy() or may not always be optimal that way. On
ia64 specifically the trapframe contains information that is specific
to an entry into the kernel and can only be used by the corresponding
exit from the kernel. A trapframe copied verbatim from another frame
is in most cases useless without some additional normalization.
Note that this change removes the assignment to td->td_frame in some
implementations of cpu_set_upcall(). The assignment is redundant.
A previous call to cpu_thread_setup() already did the exact same
assignment. An added benefit of removing the redundant assignment is
that we can now change td_pcb without nasty side-effects.
This change officially marks the ability on ia64 for 1:1 threading.
Not tested on: amd64, powerpc
Compile & boot tested on: alpha, sparc64
Functionally tested on: i386, ia64
This machine uses a non-standard scheme to specify the interrupts to
be assigned for devices in PCI slots; instead of giving the INO
or full interrupt number (which is done for the other devices in this
box), the firmware interrupt properties contain intpin numbers, which
have to be swizzled as usual on PCI-PCI bridges; however, the PCI host
bridge nodes have no interrupt map, so we need to guess the
correct INO by slot number of the device or the closest PCI-PCI
bridge leading to it, and the intpin.
To do this, this fix makes the following changes:
- Add a newbus method for sparc64 PCI host bridges to guess
the INO, and glue code in ofw_pci_orb_callback() to invoke it based
on a new quirk entry. The guessing is only done for interrupt numbers
too low to contain any IGN found on e450s.
- Create another new quirk entry was created to prevent mapping of EBus
interrupts at PCI level; the e450 has full INOs in the interrupt
properties of EBus devices, so trying to remap them could cause
problems.
- Set both quirk entries for e450s; remove the no-swizzle entry.
- Determine the psycho half (bus A or B) a driver instance manages
in psycho_attach()
- Implement the new guessing method for psycho, using the slot number,
psycho half and property value (intpin).
Thanks go to the testers, especially Brian Denehy, who tested many kernels
for me until I had found the right workaround.
Tested by: Brian Denehy <B.Denehy@90east.com>, jake, fenner,
Marius Strobl <marius@alchemy.franken.de>,
Marian Dobre <mari@onix.ro>
Approved by: re (scottl)
The current name is confusing, because it indicates to
the client that a bus_dmamap_sync() operation is not
necessary when the flag is specified, which is wrong.
The main purpose of this flag is to hint the underlying
architecture that DMA memory should be mapped in a coherent
way, but the architecture can ignore it. But if the
architecture does supports coherent mapping of memory, then
it makes bus_dmamap_sync() calls cheap.
This flag is the same as the one in NetBSD's Bus DMA.
Reviewed by: gibbs, scottl, des (implicitly)
Approved by: re@ (jhb)
value to be written into tick_compare in tick_hardclock(). While
we were taking care that the value to be written was at least TICK_GRACE
ticks in the future, a vector interrupt could happen between calculating
the value and writing it. If it took longer than TICK_GRACE to complete
(which is doubtful for a single device-triggered vector interrupt, but
quite likely for some IPIs), the value written would be in the past
and tick interrupts (which drive hardclock and statclock) would stop
until %tick wraps around, which takes a long time.
Also, increase TICK_GRACE from 1000 to 10000 for good measure.
Reported by: kris
Reviewed by: jake
Approved by: re (scottl)
BUS_DMASYNC_ definitions remain as before. The does not change the ABI,
and reverts the API to be a bit more compatible and flexible. This has
survived a full 'make universe'.
Approved by: re (bmah)
- Fix visibilty test for LONG_BIT and WORD_BIT. `#if defined(__FOO_VISIBLE)'
is alays wrong because __FOO_VISIBLE is always defined (to 0 for
invisibility).
sys/<arch>/include/limits.h
sys/<arch>/include/_limits.h:
- Style fixes.
Submitted by: bde
Reviewed by: bsdmike
Approved by: re (scottl)
- Move struct sigacts out of the u-area and malloc() it using the
M_SUBPROC malloc bucket.
- Add a small sigacts_*() API for managing sigacts structures: sigacts_alloc(),
sigacts_free(), sigacts_copy(), sigacts_share(), and sigacts_shared().
- Remove the p_sigignore, p_sigacts, and p_sigcatch macros.
- Add a mutex to struct sigacts that protects all the members of the struct.
- Add sigacts locking.
- Remove Giant from nosys(), kill(), killpg(), and kern_sigaction() now
that sigacts is locked.
- Several in-kernel functions such as psignal(), tdsignal(), trapsignal(),
and thread_stopped() are now MP safe.
Reviewed by: arch@
Approved by: re (rwatson)
Remove DBL_DIG, DBL_MIN, DBL_MAX and their FLT_ counterparts, they
were marked for deprecation ever since SUSv1 at least.
Only define ULLONG_MIN/MAX and LLONG_MAX if long long type is
supported.
Restore a lost comment in MI _limits.h file and remove it from
sys/limits.h where it does not belong.
quite excessive, and caused the available space to be used up too
easily. The new limit should be a better estimation of how much the
caller will need at most.
- Double the IOTSB size 64kB, for a DVMA area size of 64MB.
This should fix DMA problems on e450s and other large machines due
to DVMA space exhaustion, which were introduced in my last IOMMU
code revision in January.
Reported and tested by: fenner
that were added to sparc64 and later powerpc, really should have been in
the MI area. But changing that now with insufficient preperation will
just cause too much pain.
Move MD_FETCH() to the MI sys/linker.h file to avoid another two copies
of it.
syscall return values should be cleared. The system calls
getcontext() and swapcontext() want to return 0 on success
but these contexts can be switched to at a later time so
the return values need to be cleared in the saved register
sets. Other callers of get_mcontext() would normally want
the context without clearing the return values.
Remove the i386-specific context saving from the KSE code.
get_mcontext() is not i386-specific any more.
Fix a bad pointer in the alpha get_mcontext() code. The
context was being bcopy()'d from &td->tf_frame, but tf_frame
is itself a pointer, so the thread was being copied instead.
Spotted by jake.
Glanced at by: jake
Reviewed by: bde (months ago)
to get actual constant values. This is in preparation for machine/limits.h
retirement.
Discussed on: standards@
Submitted by: Craig Rodrigues <rodrigc@attbi.com> (*)
Modified by: kan
ethernet controller. The driver has been tested with the LinkSys
USB200M adapter. I know for a fact that there are other devices out
there with this chip but don't have all the USB vendor/device IDs.
Note: I'm not sure if this will force the driver to end up in the
install kernel image or not. Special magic needs to be done to exclude
it to keep the boot floppies from bloating again, someone please
advise.
the cpu dependent files. It will need to be done differently for USIII.
- Simplify the logic for detecting context rollovers. Instead of dealing
with it when the next context switch would cause the context numbers to
rollover, deal with it when they actually do rollover.
- Move some things around in cpu_switch so that we only do 1 membar #Sync
when switching address space, instead of 2.
- Detect kernel threads by comparing the new vm space to vmspace0, instead
if checking if the tlb context is 0.
- Removed some debug code.
enum to an int and redefine the BUS_DMASYNC_* constants as
flags. This allows us to specify several operations in one
call to bus_dmamap_sync() as in NetBSD.
of asserting that an mbuf has a packet header. Use it instead of hand-
rolled versions wherever applicable.
Submitted by: Hiten Pandya <hiten@unixdaemons.com>
These are called through function pointers so that different implementations
can be provided for cheetah, where the block load instructions may or may
not be a win, and so they can be disabled with the machdep.use_vis tunable.
In terms of raw bandwidth the integer versions are faster, but not allocating
lines in the L2 cache for useless data gives a measurable improvement in user
time for the benchmarks I tested (mostly buildworld with -j8).
As far as I can tell the instructions used are implemented on everything
back to UltraSPARC I, so there should not be a problem with different cpu
types.
to take care of the KAME IPv6 code which needs ovbcopy() because NetBSD's
bcopy() doesn't handle overlap like ours.
Remove all implementations of ovbcopy().
Previously, bzero was a function pointer on i386, to save a jmp to
bzero_vector. Get rid of this microoptimization as it only confuses
things, adds machine-dependent code to an MD header, and doesn't really
save all that much.
This commit does not add my pagezero() / pagecopy() code.
can do 64 bytes at a time and don't allocate lines in the L2 cache. These
assume that everything is 64 byte aligned, and that there's more than 128
bytes of data (best for whole pages). The block load and store instructions
don't follow normal memory ordering rules and require either a memory barrier
or move between registers before the data can actually be used. This
implementation correctly shuffles around 3 out of the 4 sets of registers
in order to avoid memory barriers expect for the last 2 blocks.
will be saved if we context switch as a result of an interrupt which occured
while using the floating point registers in the kernel (which actually can't
happen right now). This allows fp disabled traps in the kernel, which
normally shouldn't happen, so make sure the trapping code is what we expect
it is.
used to support block copy and zero operations in the kernel which use the
floating point registers.
- While I'm changing the size, improve the layout of struct pcb, sort by size,
then alphabetical etc.
- Add some assertions to validate assumptions made about how the pcb is
allocated.
