The adr instruction allows for an address of +-1M from the instruction.
If we replace these with an adrp and an add instruction we can generate
an address +-4G. The adrp will get an address of the 4k page the label
is within, and the add uses the :lo12: prefix to add just the low bits
to this address.
This will allow us to move things around with fewer issues than if we
needed to keep them within the +-1MB range.
Sponsored by: Innovate UK
This sysctl node can generate very verbose output, so don't trigger it
for sysctl -a or sysctl vm.pmap.
Reviewed by: markj, kib
Differential Revision: https://reviews.freebsd.org/D27504
One of the disadvantages of our current busdma code is the fact that
we process the bounced buffer in a page-by-page manner. This means that
the short (subpage) buffer allocated across page boundaries is bounced
to 2 separate pages.
This suboptimal behavior is consistent across all platforms and can be
related to (probably unimplementable or incompatible with bouncing)
BUS_DMA_KEEP_PG_OFFSET flag.
Therefore, allocate one additional page to be fully comply with this
requirement.
Discused with: markj
PR: 251018
Ability to load-balance traffic over multiple path is a must-have thing for routers.
It may be used by the servers to balance outgoing traffic over multiple default gateways.
The previous implementation, RADIX_MPATH stayed in the shadow for too long.
It was not well maintained, which lead us to a vicious circle - people were using
non-contiguous mask or firewalls to achieve similar goals. As a result, some routing
daemons implementation still don't have multipath support enabled for FreeBSD.
Turning on ROUTE_MPATH by default would fix it. It will allow to reduce networking
feature gap to other operating systems. Linux and OpenBSD enabled similar support
at least 5 years ago.
ROUTE_MPATH does not consume memory unless actually used. It enables around ~1k LOC.
It does not bring any behaviour changes for userland.
Additionally, feature is (temporarily) turned off by the net.route.multipath sysctl
defaulting to 0.
Differential Revision: https://reviews.freebsd.org/D27428
Some older PSCI implementations corrupt (or do not pass) the context_id
argument to newly started secondary cores. Although the ideal solution to this
problem is u-boot update, we can find the correct value for the argument (cpuid)
by comparing of real core mpidr register with the value stored in pcu->mpidr.
MFC after: 2 weeks
The definition was copied from amd64, but the layout of the struct
differs slightly between these platforms. This fixes spurious
`unsupported sigaction flag 0xXXXXXXXX` messages when executing some
Linux binaries on arm64.
Reviewed by: emaste
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D27460
This same check is used on other architectures. Previously this would
permit a stack frame to unwind into any arbitrary kernel address
(including unmapped addresses).
Reviewed by: andrew, markj
Obtained from: CheriBSD
Sponsored by: DARPA
Differential Revision: https://reviews.freebsd.org/D27362
We assume the boot CPU is always CPU 0 on arm64. To allow for this reserve
cpuid 0 for the boot CPU in the ACPI and FDT cases but otherwise start the
CPU as normal. We then check for the boot CPU in start_cpu and return as if
it was started.
While here extract the FDT CPU init code into a new function to simplify
cpu_mp_start and return FALSE from start_cpu when the CPU fails to start.
Reviewed by: mmel
Sponsored by: Innovate UK
Differential Revision: https://reviews.freebsd.org/D27497
- record MPIDR for all started cores in pcpu, they will be used as link
between physical locality of given core, ID in external description
(FDT or ACPI) and cupid.
- because of above, cpuid can (and should) be freely assigned, only boot
CPU must have cpuid 0. Simplify startup code according this.
Please note that pure cpuid is not sufficient instrument to hold any
information about core or cluster topology, nor to determistically iterate
over subpart of cores in CPU (iterate over all cores in single cluster for
example). Situation is more complicated by fact that PSCI can reject start
of core without reporting error (because power budget for example), or by
fact that is possible that we booted on non-first core in cluster (thus with
cpuid 0 assigned to random core).
Given cores topology should be exhibited to other parts of system
(for example to scheduler for big.little or multicluster systems) by using
smp_topo interface.
Differential Revision: https://reviews.freebsd.org/D13863
Follow-up to r353959 and r368070: do the same for other architectures.
arm32 already seems to use its own .fnstart/.fnend directives, which
appear to be ARM-specific variants of the same thing. Likewise, MIPS
uses .frame directives.
Reviewed by: arichardson
Differential Revision: https://reviews.freebsd.org/D27387
On some of the server-grade ARM64 machines the number of NUMA domains is higher
than 2. When booting GENERIC kernel on such machines the SRAT parser fails
leaving the system with a single domain. To make GENERIC kernel usable on those
server, match the parameter value with the one for amd64 arch.
Reviewed by: allanjude
Differential Revision: https://reviews.freebsd.org/D27368
Sponsored by: Ampere Computing
Submitted by: Klara, Inc.
Since EDK2 commit d8e36289cef7bde628b023219cd65fa8e8d4562a, the Graphical console may
completely hide SPCR, causing panics later when locating timers.
As such simply rely on the ACPI Root pointer presence.
Submitted by: dan.kotowski@a9development.com
Reviewed by: andrew, mw
Differential Revision: https://reviews.freebsd.org/D27306
When there is no ACPI redistributor sub-table in the MADT we need to
fall back to use the GICR base address from the GIC CPU interface
structure.
Handle this fallback when adding memory to the device and when counting
the number of redistributors.
PR: 251171
Reported by: Andrey Fesenko <f0andrey_gmail.com>
Sponsored by: Innovate UK
Differential Revision: https://reviews.freebsd.org/D27247
The former tries to dereference memory allocated by the latter. If counting
the redistributor fails it may try to dereference memory that was never
allocated.
Sponsored by: Innovate UK
The same driver works on both, allow the driver to attach to a GICv4
controller with the ACPI attachment.
Reported by: Andrey Fesenko <f0andrey_gmail.com>
Sponsored by: Innovate UK
This adds an arm64 iommu interface and a driver for Arm System Memory
Management Unit version 3.2 (ARM SMMU v3.2) specified in ARM IHI 0070C
document.
Hardware overview is provided in the header of smmu.c file.
The support is disabled by default. To enable add 'options IOMMU' to your
kernel configuration file.
The support was developed on Arm Neoverse N1 System Development Platform
(ARM N1SDP), kindly provided by ARM Ltd.
Currently, PCI-based devices and ACPI platforms are supported only.
The support was tested on IOMMU-enabled Marvell SATA controller,
Realtek Ethernet controller and a TI xHCI USB controller with a low to
medium load only.
Many thanks to Konstantin Belousov for help forming the generic IOMMU
framework that is vital for this project; to Andrew Turner for adding
IOMMU support to MSI interrupt code; to Mark Johnston for help with SMMU
page management; to John Baldwin for explaining various IOMMU bits.
Reviewed by: mmel
Relnotes: yes
Sponsored by: DARPA / AFRL
Sponsored by: Innovate UK (Digital Security by Design programme)
Differential Revision: https://reviews.freebsd.org/D24618
In r367327 generic_bs_sr_<n> were derived from mips. Given we are calling
generic_bs_w_<n> and no write directly, we do not have to do the address
calculations ourselves as eneric_bs_w_<n> will do a str val [bsh, offset].
All we actually have to do is increment offset.
MFC after: 3 days
Memory allocated by bus_dmamem_alloc will take into account any alignment
requirements of the CPU it's running on. Stop trying to bounce in this case
as there is no bounce zone allocated.
Reported by: manu, tuexen
Tested by: manu
Sponsored by: Innovate UK
Implement the bs_sr_<N> generic functions based on the generic
mips implementation calling the generic bs_w_<N> functions in a loop.
ral(4) (rt2860.c) panics in RAL_SET_REGION_4() because bs_sr_4()
is NULL. It seems ral(4) and ti(4) might be the only consumers of
these functions I could find quickly so keeping them in C rather than asm.
Reported by: Steve Wheeler (https://redmine.pfsense.org/issues/11021)
Reviewed by: mmel
MFC after: 3 days
The stage 2 arm64 page tables may need to start at a lower level. This
is because we may only be able to map a limited IPA range and trying
to use a full 4 levels will cause the CPU to fault in an unrecoverable
way.
To simplify the code we still allocate the full 4 levels, however level 0
will only ever be used to find the level 1 table used as the base. Handle
this by creating a dummy entry in the level 0 table to point to the level 1
table.
Sponsored by: Innovate UK
Differential Revision: https://reviews.freebsd.org/D26066
VM_ALLOC_WAITOK and vm_page_unwire_noq(), have eliminated the need for
many of the #includes.
Reviewed by: kib, markj
Differential Revision: https://reviews.freebsd.org/D27052
The multipage alignment requirements is incompatible with many aspects
of actual busdma code. Multi-page alignment requests are incompatible
with many aspects of current busdma code. Mainly with partially bounced
buffer segments and per-page loop in bus_dmamap_load_buffer(). Because
proper implementation would be a major restructuring of the code, add
the fix only for already known uses and do KASSERT for all other cases.
For this reason, bus_dmamap_load_buffer () should take the memory allocated
by bus_dmam_alloc () as one segment bypassing per page segmentation. We can
do this because it is guaranteed that the memory is physically continuous.
Reviewed by: bz
Tested by: imp, mv, daniel.engberg.lists_pyret.net, kjopek_gmail.com
Differential Revision: https://reviews.freebsd.org/D26735
function checks that the mutex lock is owned.
This fixes 'devctl disable re0' operation.
Sponsored by: Innovate DSbD
Differential Revision: https://reviews.freebsd.org/D26904
PCPU_GET(curpmap) expands to multiple instructions on arm64, and if the
current thread is migrated in between execution of those instructions, a
stale value may be used in the assertion condition.
Diagnosed by: mmel
Reported by: mmel, Bob Prohaska <fbsd@www.zefox.net>
Submitted by: alc
MFC after: 1 week
Linux execve() gets audited as AUE_EXECVE as well, we should also interpret
the return from this correctly for the same reasoning as in r367002.
MFC with: r367002
pagezero(). Ultimately, they use the same method for bulk zeroing, but
the generality of bzero() requires size and alignment checks that
pagezero() does not.
Eliminate an unnecessary #include.
Reviewed by: emaste, markj
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D26876
Use ELR register value instead of LR for PMC_TRAPFRAME_TO_PC macro since
it's the former that indicates PC if the interrupted execution thread.
This fixes a bug where pmcstat lost the leaf function of the call chain
and started with the second function in the chain.
Although this change is an improvement over the previous logic there is still
posibility for incomplete data: if the leaf function does not have stack
variables and does not call any other functions compiler would not generate
a stack frame for it and the FP value would point to the caller's frame, so
instead of the actual "caller1 -> caller2 -> leaf" chain only
"caller1 -> leaf" would be captured.
Sponsored by: Ampere Computing
Submitted by: Klara, Inc.
In the functions that copy between userspace and kernel space we check the
user space address is valid before performing the copy. These are mostly
identical within each type of function so create two macros to perform the
check.
Obtained from: CheriBSD
Sponsored by: Innovate UK
These were missed in the previous pass. The extensions (partially)
supported by this change are:
- ARMv8.2-FHM, Floating-point multiplication variant
- ARMv8.4-LSE, Large System Extensions
- ARMv8.4-DIT, Data Independent Timing instructions
Reviewed by: andrew, markj
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D26707
This brings these definitions in sync with the ARMv8.6 version of the
architecture reference manual.
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D26706
Hiding this feature behind RB_VERBOSE is gratuitous. The tunable is enough
to limit its use to only those who explicitly request it.
Suggested by: kevans
Ampere Altra in a dual socket configuration has 12 ITSes for the
12 PCIe root complexes. The NIRQ interrupts are statically split
between each child of the gic bus, so here we increase that
value. 16k is enough for
(#cpus * #its * max_pcie_bifurcation) LPIs + (#SPIs and #PPIs)
Reviewed by: jhb
Approved by: scottl (implicit)
MFC after: 1 week
Sponsored by: Ampere Computing
Differential Revision: https://reviews.freebsd.org/D26766
Move dump_avail[] extern declaration and inlines into a new header
vm/vm_dumpset.h. This fixes default gcc build for mips.
Reviewed by: alc, scottph
Tested by: kevans (previous version)
Sponsored by: The FreeBSD Foundation
Differential revision: https://reviews.freebsd.org/D26741
These already use the load variant that simulates userspace access.
Remove the macros that enable normal loads and stores from userspace
as they are unneeded.
Sponsored by: Innovate UK
When trapping on a wrote access to a buffer the kernel has mapped as write
only we should only pass the VM_PROT_WRITE flag. Previously the call to
vm_fault_trap as the VM_PROT_READ flag was unexpected.
Reported by: manu
Sponsored by: Innovate UK
This patch has the driver for 10Gigabit Ethernet controller in AMD
SoC. This driver is written compatible to the Iflib framework. The
existing driver is for the old version of hardware. The submitted
driver here is for the recent versions of the hardware where the Ethernet
controller is PCI-E based.
Submitted by: Rajesh Kumar <rajesh1.kumar@amd.com>
MFC after: 1 month
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D25793
Push the root seed version to userspace through the VDSO page, if
the RANDOM_FENESTRASX algorithm is enabled. Otherwise, there is no
functional change. The mechanism can be disabled with
debug.fxrng_vdso_enable=0.
arc4random(3) obtains a pointer to the root seed version published by
the kernel in the shared page at allocation time. Like arc4random(9),
it maintains its own per-process copy of the seed version corresponding
to the root seed version at the time it last rekeyed. On read requests,
the process seed version is compared with the version published in the
shared page; if they do not match, arc4random(3) reseeds from the
kernel before providing generated output.
This change does not implement the FenestrasX concept of PCPU userspace
generators seeded from a per-process base generator. That change is
left for future discussion/work.
Reviewed by: kib (previous version)
Approved by: csprng (me -- only touching FXRNG here)
Differential Revision: https://reviews.freebsd.org/D22839
Now that config(8) has supported include for 19 years, transition to
including the NOTES files. include support didn't exist at the time,
nor did the envvar stuff recently added. Now that it does, eliminate
the building of LINT files by just including everything you need.
Note: This may cause conflicts with updating in some cases.
find sys -name LINT\* -rm
is suggested across this commit to remove the generated LINT
files.
Reviewed by: kevans
Differential Revision: https://reviews.freebsd.org/D26540
The boot metadata (also referred to as modinfo, or preload metadata)
provides information about the size and location of the kernel,
pre-loaded modules, and other metadata (e.g. the EFI framebuffer) to be
consumed during by the kernel during early boot. It is encoded as a
series of type-length-value entries and is usually constructed by
loader(8) and passed to the kernel. It is also faked on some
architectures when booted by other means.
Although much of the module information is available via kldstat(8),
there is no easy way to debug the metadata in its entirety. Add some
routines to parse this data and allow it to be printed to the console
during early boot or output via a sysctl.
Since the output can be lengthly, printing to the console is gated
behind the debug.dump_modinfo_at_boot kenv variable as well as the
BOOTVERBOSE flag. The sysctl to print the metadata is named
debug.dump_modinfo.
Reviewed by: tsoome
Sponsored by: NetApp, Inc.
Sponsored by: Klara, Inc.
Differential Revision: https://reviews.freebsd.org/D26687
It is unlikely, but possible, that an unrecognized or unsupported
relocation type is encountered while trying to load a kernel module. If
this occurs we should offer the symbol index as a hint to the user.
While here, fix some small style issues.
Reviewed by: markj, kib (amd64 part, in D26701)
Sponsored by: NetApp, Inc.
Sponsored by: Klara, Inc.
This appears to be a typo. The AdvSIMD field encodes support for
half-precision floating point SIMD instructions, which corresponds to
HWCAP_ASIMDHP, not HWCAP_ASIMDDP.
MFC after: 3 days
Sponsored by: The FreeBSD Foundation
Use address of the pointer passed to kernel to determine whether the pointer
is a FDT block (physical address) or a module pointer (virtual kernel address).
This fragment was supposed to be committed before r366196, but I accidentally
skipped it in a patch series.
Reported by: bz
It was removed in r355289 but forgot to return it back when new u-boot booti
support was committed. Although booti is not the preferred method of
booting the kernel, it is very useful for the initial phase of porting
FreeBSD to a new platform or booting the kernel on various embedded boards
in an industrial environment.
Don't map same physical memory multiple times with different cache attributes.
This is explicitly stated as architectural undefined behavior, leading to
coherency issues sooner or later.
- We can exit the loop as soon as the filter check passes.
- The alignment check has already passed so there is no need to also run
it here.
Sponsored by: Innovate UK
We need to use a bounce buffer when the memory we are operating on is not
aligned to a cacheline, and not aligned to the maps alignment.
The former is to stop other threads from dirtying the cacheline while we
are performing DMA operations with it. The latter is to check memory
passed in by a driver is correctly aligned for the device.
Reviewed by: mmel
Sponsored by: Innovate UK
Differential Revision: https://reviews.freebsd.org/D26496
This will ensure nothing modifies the cacheline while DMA is in progress
so we won't need to bounce the data.
Reviewed by: mmel
Sponsored by: Innovate UK
Differential Revision: https://reviews.freebsd.org/D26495
Use it to decide if we can skip cache management.
While here remove the DMAMAP_COULD_BOUNCE flag as it's unneeded.
Reviewed by: mmel
Sponsored by: Innovate UK
Differential Revision: https://reviews.freebsd.org/D26494
Add helper functions to the arm64 busdma for common cases of checking if
we may need to bounce, and if we must bounce for a given address.
These will be expanded later as we handle cache-misaligned memory.
Reported by: mmel
Sponsored by: Innovate UK
Differential Revision: https://reviews.freebsd.org/D26493
On Ampere Altra systems, the sparse population of RAM within the
physical address space causes the vm_page_dump bitmap to be much
larger than necessary, increasing the size from ~8 Mib to > 2 Gib
(and overflowing `int` for the size).
Changing the page dump bitmap also changes the minidump file
format, so changes are also necessary in libkvm.
Reviewed by: jhb
Approved by: scottl (implicit)
MFC after: 1 week
Sponsored by: Ampere Computing, Inc.
Differential Revision: https://reviews.freebsd.org/D26131
These definitions were repeated by all architectures, with small
variations. Consolidate the common definitons in machine
independent code and use bitset(9) macros for manipulation. Many
opportunities for deduplication remain in the machine dependent
minidump logic. The only intended functional change is increasing
the bit index type to vm_pindex_t, allowing the indexing of pages
with address of 8 TiB and greater.
Reviewed by: kib, markj
Approved by: scottl (implicit)
MFC after: 1 week
Sponsored by: Ampere Computing, Inc.
Differential Revision: https://reviews.freebsd.org/D26129
pmap_update_entry() will temporarily clear the valid bit of page table
entries in order to satisfy the arm64 pmap's break-before-make
constraint. pmap_kextract() may operate concurrently on kernel page
table pages, introducing windows where the assertions added in r365879
may fail incorrectly since they implicitly assert that the valid bit is
set. Modify the assertions to handle this.
Reviewed by: andrew, mmel (previous version)
Reviewed by: alc, kib
Reported by: mmel, scottph
MFC with: r365879
Due to a HW bug in the RockChip PCIe implementation, attempting to access
a non-existent register in the configuration space will throw an exception.
Use new bus functions bus_peek() and bus_poke() to overcomme this limitation.
One problem with the bus_space_read_N() and bus_space_write_N() family of
functions is that they provide no protection against exceptions which can
occur when no physical hardware or device responds to the read or write
cycles. In such a situation, the system typically would panic due to a
kernel-mode bus error. The bus_space_peek_N() and bus_space_poke_N() family
of functions provide a mechanism to handle these exceptions gracefully
without the risk of crashing the system.
Typical example is access to PCI(e) configuration space in bus enumeration
function on badly implemented PCI(e) root complexes (RK3399 or Neoverse
N1 N1SDP and/or access to PCI(e) register when device is in deep sleep state.
This commit adds a real implementation for arm64 only. The remaining
architectures have bus_space_peek()/bus_space_poke() emulated by using
bus_space_read()/bus_space_write() (without exception handling).
MFC after: 1 month
Reviewed by: kib
Differential Revision: https://reviews.freebsd.org/D25371
that can be extended, but also ensure compile-time type checking. Refactor
common code out of arch-specific implementations. Move the mpr and mps
drivers to this new API. The template type remains visible to the consumer
so that it can be allocated on the stack, but should be considered opaque.
As the pl061 driver can be an interrupt controller attach it earlier in the
boot so other drivers can use it.
Use a new GPIO xref to not conflict with the existing root interrupt
controller.
Sponsored by: Innovate UK
Expose some of the new HWCAP features added in r65304. This includes the
addition of elf_hwcap2 into the sysvec, and a separate function to parse
for those features.
This only exposes features which require no further configuration, e.g.
indicating the presence of certain instructions. Larger features (SVE)
will not be advertised until we actually support them. The exact list of
features/extensions this patch exposes is:
- ARMv8.0-DGH
- ARMv8.0-SB
- ARMv8.2-BF16
- ARMv8.2-DCCVADP
- ARMv8.2-I8MM
- ARMv8.4-LRCPC
- ARMv8.5-CondM
- ARMv8.5-FRINT
- ARMv8.5-RNG
- PSTATE.SSBS
While here, annotate elf_hwcap and elf_hwcap2 as __read_frequently, and
move the declarations to the machine/md_var.h header.
Submitted by: mikael@ (D22314 portion)
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D26031
Differential Revision: https://reviews.freebsd.org/D22314
FreeBSD exports CPU features as bits in the AT_HWCAP and AT_HWCAP2
vectors via elf_aux_info(3). This interface is similar to getauxval(3)
on Linux, and for simplicity to consumers we try to maintain an
identical set of feature flags on arm64.
The first batch of AT_HWCAP flags were added in r350166, corresponding
to definitions that already existed in Linux. Unfortunately, one flag
was missed, and a portion of the values are shifted one bit to the right
as a result.
Add the missing definition for HWCAP_ASIMDHP, and adjust the affected
values to match their Linux counterparts.
Although this is an ABI-breaking change, there is no plan to provide
compat code for old binaries. An audit of our ports tree and other
software via Debian code search indicates that there are not yet any
consumers of this interface for FreeBSD/arm64.
Bump __FreeBSD_version to be on the safe side, in case compat code needs
to be added in the future.
Reviewed by: emaste, manu
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D26329
A PL061 is a simple 8 pin GPIO controller. This GPIO device is used to
signal an internal request for shutdown on some virtual machines including
Arm-based Amazon EC2 instances.
Submitted by: Ali Saidi <alisaidi_amazon.com> (previouss version)
Reviewed by: Ali Saidi, manu
Differential Revision: https://reviews.freebsd.org/D24065
Allwinner USB DRD is based on the Mentor USB OTG controller, with a
different register layout and a few missing registers.
The code is by Andrew Turner (andrew).
Reviewed by: hselasky, manu
Obtained from: andrew
MFC after: 5 weeks
Differential Revision: https://reviews.freebsd.org/D5881
This is in sync with what is defined for Linux 5.8. Note that all bits
in HWCAP are exhausted, and HWCAP2 has been added.
This also revealed an error in some of the existing definitions. We are
missing HWCAP_ASIMDHP, and as a result a portion of the HWCAP values are
shifted right by one bit. This will be fixed in an upcoming change, but
the values being added now are compatible with what Linux defines.
Reviewed by: emaste, markj, manu
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D26030
We don't need these pagetables after the early boot. Remove the chance we
write to memory we didn't expect to and remove architectural undefined
behaviour.
Reviewed by: alc (earlier version), mmel
Sponsored by: Innovate UK
Differential Revision: https://reviews.freebsd.org/D22606
Currently we use a single bit to indicate whether the virtual page is
part of a superpage. To support a forthcoming implementation of
non-transparent 1GB superpages, it is useful to provide more detailed
information about large page sizes.
The change converts MINCORE_SUPER into a mask for MINCORE_PSIND(psind)
values, indicating a mapping of size psind, where psind is an index into
the pagesizes array returned by getpagesizes(3), which in turn comes
from the hw.pagesizes sysctl. MINCORE_PSIND(1) is equal to the old
value of MINCORE_SUPER.
For now, two bits are used to record the page size, permitting values
of MAXPAGESIZES up to 4.
Reviewed by: alc, kib
Sponsored by: Juniper Networks, Inc.
Sponsored by: Klara, Inc.
Differential Revision: https://reviews.freebsd.org/D26238
This allows privileged userspace processes to find information about the
physical page backing a given mapping. It is useful in applications
such as DPDK which perform some of their own memory management.
Reviewed by: kib, jhb (previous version)
MFC after: 2 weeks
Sponsored by: Juniper Networks, Inc.
Sponsored by: Klara Inc.
Differential Revision: https://reviews.freebsd.org/D26237
This whitespace was intentionally added to help differentiate the different
register groups within this file.
While here add missing whitespace from earlier in the file,
Sponsored by: Innovate UK
When enabling the MMU on arm64 we need to ensure the tlb invalidation has
completed before setting the enable bit in the SCTLR register.
Reported by: alc
Sponsored by: Innovate UK
Add support for stage 2 pmap to pmap_pte_dirty, pmap_release, and more
of pmap_enter. This adds support in all placess I have hit while testing
bhyve ehile faulting pages in as needed.
Sponsored by: Innovate UK
Differential Revision: https://reviews.freebsd.org/D26065
The Ampere Altra has physical memory populated sparsely within the
physical address space. Increase the size of the dmap to cover all
physical memory.
Reviewed by: andrew
Approved by: scottl (implicit)
MFC after: 1 week
Sponsored by: Ampere Computing, Inc.
Differential Revision: https://reviews.freebsd.org/D26134
Add a synchronizing instruction to flush and wait until the local
CPU's writes are observable to other CPUs before sending IPIs.
This fixes an issue where recipient CPUs doing a rendezvous could
enter the rendezvous handling code before the initiator's writes
to the smp_rv_* variables were visible. This manifested as a
system hang, where a single CPU's increment of smp_rv_waiters[0]
actually happened "before" the initiator's zeroing of that field,
so all CPUs were stuck with the field appearing to be at
ncpus - 1.
Reviewed by: andrew, markj
Approved by: scottl (implicit)
MFC after: 1 week
Sponsored by: Ampere Computing, Inc.
Differential Revision: https://reviews.freebsd.org/D25798
Currently, we parse notes for the values of ELF FreeBSD feature flags
and osrel. Knowing these values, or knowing that image does not carry
the note if pointers are NULL, is useful to decide which ABI variant
(brand) we want to activate for the image.
Right now this is only a plumbing change
Tested by: pho
Sponsored by: The FreeBSD Foundation
Differential revision: https://reviews.freebsd.org/D25273
According to the ARM Design Document "IO Remapping Table Platform"
(DEN 0049D), the "Number of IDs" field of the ID mapping format means
"The number of IDs in the range minus one".
Submitted by: Greg V <greg@unrelenting.technology>
Reviewed by: andrew
Differential Revision: https://reviews.freebsd.org/D25179
Those messages were printed hundreds of times during boot, often multiple
times for each table. We already print information about the tables in
more organized form once to not duplicate it when random ACPI drivers are
attaching.
MFC after: 1 week
This is a step towards facilitating jails with only Linux binaries.
Supporting emul_path adds path lookups which are completely spurious
if the binary at hand runs in a Linux-based root directory.
It defaults to on (== current behavior).
make -C /root/linux-5.3-rc8 -s -j 1 bzImage:
use_emul_path=1: 101.65s user 68.68s system 100% cpu 2:49.62 total
use_emul_path=0: 101.41s user 64.32s system 100% cpu 2:45.02 total
The hard work of parsing fields per-CPU, handling heterogeneous
features, and excluding features from userspace is already done by
update_special_regs. We can build our set of HWCAPs from the result.
This exposed a small bug in update_special_regs, in which the
generated bitmask was not wide enough, and as a result some bits
weren't being exposed in user_cpu_desc. Fix this.
While here, adjust some formatting.
Reviewed by: andrew
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D26069
This adds definitions for the latest additions to the AA64ISAR[01] ID
registers. This brings these registers in sync with ARMv8.6 initial spec
release.
An future change will parse many of these fields for HWCAP features.
Reviewed by: andrew, manu, markj (all previous versions)
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D26029
This adds support for the Cortex-A76 and Neoverse-N1 PMU counters to pmc.
While here add more PMCR_IDCODE values and check the implementers code is
correct before setting the PMU type.
Reviewed by: bz, emaste (looks reasonable to me)
Sponsored by: Innovate UK
Differential Revision: https://reviews.freebsd.org/D25959
- Do not rely on U-Boot for clocks configuration, enable and set frequencies
in the driver's attach method.
- Adjust MAC settings according to detected linespeed on RK3399 and RK3328.
- Add support for RMII PHY mode on RK3328.
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D26006
Ethernet clocks on RK3328 are controlled by SYSCON registers, so add
RK_CLK_COMPOSITE_GRF flag to indicate that clock node should access grf
registers instead of CRU's
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D25918
APEI allows platform to report different kinds of errors to OS in several
ways. We've found that Supermicro X10/X11 motherboards report PCIe errors
appearing on hot-unplug via this interface using NMI. Without respective
driver it ended up in kernel panic without any additional information.
This driver introduces support for the APEI Generic Hardware Error Source
reporting via NMI, SCI or polling. It decodes the reported errors and
either pass them to pci(4) for processing or just logs otherwise. Errors
marked as fatal still end up in kernel panic, but some more informative.
When somebody get to native PCIe AER support implementation both of the
reporting mechanisms should get common error recovery code. Since in our
case errors happen when the device is already gone, there is nothing to
recover, so the code just clears the error statuses, practically ignoring
the otherwise destructive NMIs in nicer way.
MFC after: 2 weeks
Relnotes: yes
Sponsored by: iXsystems, Inc.
Being able to use tmpfs without kernel modules is very useful when building
small MFS_ROOT kernels without a real file system.
Including TMPFS also matches arm/GENERIC and the MIPS std.MALTA configs.
Compiling TMPFS only adds 4 .c files so this should not make much of a
difference to NO_MODULES build times (as we do for our minimal RISC-V
images).
Reviewed By: br (earlier version for riscv), brooks, emaste
Differential Revision: https://reviews.freebsd.org/D25317
This new function allows us to find the SMMU instance assigned
for a particular PCI RID.
Reviewed by: andrew
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D25687
This removes SCTP from in-tree kernel configuration files. Now, SCTP
can be enabled by simply loading the module, as discussed on
freebsd-net@.
Reviewed by: tuexen
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D25611
It can be useful to get a dump of all registers when investigating why we
received an exception that we are unable to handle. In these cases we
already call panic, however we don't always print the registers.
Add calls to print_registers and print esr and far when applicable.
Sponsored by: Innovate UK
The EIP-97 is a packet processing module found on the ESPRESSObin. This
commit adds a crypto(9) driver for the crypto and hash engine in this
device. An initial skeleton driver that could attach and submit
requests was written by loos and others at Netgate, and the driver was
finished by me.
Support for separate AAD and output buffers will be added in a separate
commit, to simplify merging to stable/12 (where those features don't
exist).
Reviewed by: gnn, jhb
Feedback from: andrew, cem, manu
MFC after: 1 week
Sponsored by: Rubicon Communications, LLC (Netgate)
Differential Revision: https://reviews.freebsd.org/D25417
On architectures that use RELA relocations it is safe to rerun the ifunc
resolvers on after all CPUs have started, but while they are sill parked.
On arm64 with big.LITTLE this is needed as some SoCs have shipped with
different ID register values the big and little clusters meaning we were
unable to rely on the register values from the boot CPU.
Add support for rerunning the resolvers on arm64 and amd64 as these are
both RELA using architectures.
Reviewed by: kib
Sponsored by: Innovate UK
Differential Revision: https://reviews.freebsd.org/D25455
The functions to read the common user and kernel ID registers should be
in cpu.h rather than undefined.h as they are related to CPU details and
used by undefined instruction handlers.
Sponsored by: Innovate UK
Also move parsing the registers to just after the secondary CPUs have
started. This means the kernel register view from all CPUs is available
after the CPU SYSINITs have finished, e.g. for use by ifunc resolvers.
Sponsored by: Innovate UK
Differential Revision: https://reviews.freebsd.org/D25505
- Add CCM driver and clocks implementations for i.MX 8M
- Add GPC driver for iMX8
- Add clock tree for i.MX 8M Quad
- Add clocks support and new compat strings (where required) for existing i.MX 6 UART, I2C, and GPIO drivers
- Enable aarch64-compatible drivers form i.MX 6 in arm64 GENERIC kernel config
- Add dtb/imx8 kernel module with DTBs for Nitrogen8M and iMX8MQ EVK
With this patch both Nitrogen8M and iMX8MQ EVK boot with NFS root up to multiuser login prompt
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D25274
In preparation for using ifuncs in the kernel is is useful to have a common
view of the arm64 ID registers across all CPUs. Add this and extract the
logic for finding the lower value of two fields to a new helper function.
Sponsored by: Innovate UK
Differential Revision: https://reviews.freebsd.org/D25463
