To optimize the case of ping-ponging between two buffers, the DDP code
caches the last two buffers used keeping the pages wired and page pods
stored in the NIC's RAM. If a new aio_read() request uses one of the
same buffers, then the work of holding pages, etc. can be avoided.
However, the starting virtual address of an aio buffer was not saved,
only the page count, length, and initial page offset. Thus, an
aio_read() request could match a different buffer in the address
space. (Earlier during development vm_fault_hold_quick_pages() was
always called and the vm_page_t values were compared, but that was
eventually removed without being adequately replaced.) Fix by storing
the starting virtual address and comparing that (along with other
fields) to determine if a buffer can be reused.
MFC after: 3 days
Sponsored by: Chelsio Communications
The bad_session, sglist_error, and process_error sysctl nodes were
returning the value of the pad_error node instead of the appropriate
error counters.
Sponsored by: Chelsio Communications
- start_wrq_wr must not drain the wr_list if there are incomplete_wrs
pending. This can happen when a t4_wrq_tx runs between two
start_wrq_wr.
- commit_wrq_wr must examine the cookie's pidx and ndesc with the
queue's lock held. Otherwise there is a bad race when incomplete WRs
are being completed and commit_wrq_wr for the WR that is ahead in the
queue updates the next incomplete WR's cookie's pidx/ndesc but the
commit_wrq_wr for the second one is using stale values that it read
without the lock.
MFC after: 1 week
Sponsored by: Chelsio Communications
t4_tom picks it up right away. This is less work than waiting for
the connection to be established before applying the setting.
MFC after: 2 weeks
Sponsored by: Chelsio Communications
used by the TOE hardware for fully offloaded connections. The knob
affects new connections only.
MFC after: 2 weeks
Sponsored by: Chelsio Communications
install after full initialization, and another to disable the TCB
cache (T6+). The latter works as a tunable only.
Note that debug_flags are for debugging only and should not be set
normally.
MFC after: 1 week
Sponsored by: Chelsio Communications
These firmwares come from a pre-release snapshot. The final firmwares
in this Chelsio release cycle will likely be .61.0 or later and those
will be the next "long lived" firmwares in FreeBSD head and stable
branches. .59 is being provided in head (only) for wider test exposure.
Obtained from: Chelsio Communications
Sponsored by: Chelsio Communications
creating hardware VIs.
This fixes a bad race on systems with hw.cxgbe.num_vis > 1.
Reported by: olivier@
MFC after: 1 week
Sponsored by: Chelsio Communications
the current state to determine whether to generate a link-state change
notification. This fixes a bug introduced in r321063 that caused the
driver to sometimes skip these notifications.
Reported by: Jason Eggleston @ LLNW
MFC after: 3 days
Sponsored by: Chelsio Communications
precision. These timers are already displayed in microseconds in the
sysctl MIB. Add variables to track these tunables while here.
MFC after: 3 days
Sponsored by: Chelsio Communications
debug (cudbg) code, hooked up to the main driver via an ioctl.
The ioctl can be used to collect the chip's internal state in a
compressed dump file. These dumps can be decoded with the "view"
component of cudbg.
Obtained from: Chelsio Communications
MFC after: 2 months
Sponsored by: Chelsio Communications
and keepalive in the sysctl MIB. Provide tunables to change some of
these parameters. These are supposed to be setup by the firmware so
these tunables are for experimentation only.
MFC after: 2 weeks
Sponsored by: Chelsio Communications
doesn't seem to have one. This lets the driver recover automatically
from incomplete firmware upgrades (panic, reboot, power loss, etc. in
the middle of an upgrade).
MFC after: 2 weeks
Sponsored by: Chelsio Communications
- Deal with changes to port_type, and not just port_mod when a
transceiver is changed. This fixes hot swapping of transceivers of
different types (QSFP+ or QSA or QSFP28 in a QSFP28 port, SFP+ or
SFP28 in a SFP28 port, etc.).
- Always refresh media information for ifconfig if the port is down.
The firmware does not generate tranceiver-change interrupts unless at
least one VI is enabled on the physical port. Before this change
ifconfig diplayed potentially stale information for ports that were
administratively down.
- Always recalculate and reapply L1 config on a transceiver change.
- Display PAUSE settings in ifconfig. The driver sysctls for this
continue to work as well.
MFC after: 2 weeks
Sponsored by: Chelsio Communications
the "effective MSS" for the connection. The chip expects it this way.
Submitted by: Krishnamraju Eraparaju @ Chelsio
MFC after: 3 days
Sponsored by: Chelsio Communications
Do not attempt to initialize netmap queues that are already initialized
or aren't supposed to be initialized. Similarly, do not free queues
that are not initialized or aren't supposed to be freed.
PR: 217156
Sponsored by: Chelsio Communications
- For HMAC requests, construct a special input buffer to request an empty
hash result.
- For plain cipher requests and requests that chain an AES cipher with an
HMAC, fail with EINVAL if there is no cipher payload. If needed in
the future, chained requests that only contain AAD could be serviced as
HMAC-only requests.
- For GCM requests, the hardware does not support generating the tag for
an AAD-only request. Instead, complete these requests synchronously
in software on the assumption that such requests are rare.
Sponsored by: Chelsio Communications
The adapter firmware in general does not accept PDUs larger than 64k - 1
bytes in size. Sending crypto requests larger than this size result in
hangs or incorrect output, so reject them with EFBIG. For requests
chaining an AES cipher with an HMAC, the firmware appears to require
slightly smaller requests (around 512 bytes).
Sponsored by: Chelsio Communications
The latest firmware has a number of link related fixes, support for a
new custom card, and the fix for a bug that affected rate limiting on
FreeBSD.
Obtained from: Chelsio Communications
MFC after: 1 week
Sponsored by: Chelsio Communications
The ccr(4) driver supports use of the crypto accelerator engine on
Chelsio T6 NICs in "lookaside" mode via the opencrypto framework.
Currently, the driver supports AES-CBC, AES-CTR, AES-GCM, and AES-XTS
cipher algorithms as well as the SHA1-HMAC, SHA2-256-HMAC, SHA2-384-HMAC,
and SHA2-512-HMAC authentication algorithms. The driver also supports
chaining one of AES-CBC, AES-CTR, or AES-XTS with an authentication
algorithm for encrypt-then-authenticate operations.
Note that this driver is still under active development and testing and
may not yet be ready for production use. It does pass the tests in
tests/sys/opencrypto with the exception that the AES-GCM implementation
in the driver does not yet support requests with a zero byte payload.
To use this driver currently, the "uwire" configuration must be used
along with explicitly enabling support for lookaside crypto capabilities
in the cxgbe(4) driver. These can be done by setting the following
tunables before loading the cxgbe(4) driver:
hw.cxgbe.config_file=uwire
hw.cxgbe.cryptocaps_allowed=-1
MFC after: 1 month
Relnotes: yes
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D10763
Invoke any identify routines of child drivers during attach before attaching
children, and delete any remaining devices after deleting ports.
MFC after: 1 month
Sponsored by: Chelsio Communications
