There are 4 independent knobs in T5+ chips to include or exclude PAUSE
frames from the "total frames" and "multicast frames" counters in either
direction. This change lets the driver deal with any combination of
these settings.
contiguous regions in an mbuf chain.
If the payload of an mbuf ends at a page boundary count_mbuf_nsegs would
incorrectly consider the next mbuf's payload physically contiguous based
solely on a KVA comparison.
MFC after: 1 week
Sponsored by: Chelsio Communications
come up as 't6nex' nexus devices with 'cc' ports hanging off them.
The T6 firmware and configuration files will be added as soon as they
are released. For now the driver will try to work with whatever
firmware and configuration is on the card's flash.
Sponsored by: Chelsio Communications
The cxgbev/cxlv driver supports Virtual Function devices for Chelsio
T4 and T4 adapters. The VF devices share most of their code with the
existing PF4 driver (cxgbe/cxl) and as such the VF device driver
currently depends on the PF4 driver.
Similar to the cxgbe/cxl drivers, the VF driver includes a t4vf/t5vf
PCI device driver that attaches to the VF device. It then creates
child cxgbev/cxlv devices representing ports assigned to the VF.
By default, the PF driver assigns a single port to each VF.
t4vf_hw.c contains VF-specific routines from the shared code used to
fetch VF-specific parameters from the firmware.
t4_vf.c contains the VF-specific PCI device driver and includes its
own attach routine.
VF devices are required to use a different firmware request when
transmitting packets (which in turn requires a different CPL message
to encapsulate messages). This alternate firmware request does not
permit chaining multiple packets in a single message, so each packet
results in a firmware request. In addition, the different CPL message
requires more detailed information when enabling hardware checksums,
so parse_pkt() on VF devices must examine L2 and L3 headers for all
packets (not just TSO packets) for VF devices. Finally, L2 checksums
on non-UDP/non-TCP packets do not work reliably (the firmware trashes
the IPv4 fragment field), so IPv4 checksums for such packets are
calculated in software.
Most of the other changes in the non-VF-specific code are to expose
various variables and functions private to the PF driver so that they
can be used by the VF driver.
Note that a limited subset of cxgbetool functions are supported on VF
devices including register dumps, scheduler classes, and clearing of
statistics. In addition, TOE is not supported on VF devices, only for
the PF interfaces.
Reviewed by: np
MFC after: 2 months
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7599
If a packet contains the Ethernet header (14 bytes) in the first mbuf
and the payload (IP + UDP + data) in the second mbuf, then the attempt
to fetch the l3hdr will return a NULL pointer. The first loop iteration
will drop len to zero and exit the loop without setting 'p'. However,
the desired data is at the start of the second mbuf, so the correct
behavior is to loop around and let the conditional set 'p' to m_data of
the next mbuf (and leave offset as 0).
Reviewed by: np
Sponsored by: Chelsio Communications
transfers.
The Initiator and Target both perform zero copy receive for transfers
greater than or equal to this threshold.
Sponsored by: Chelsio Communications
routines available in t4_tom to manage the iSCSI DDP page pod region.
This adds the ability to use multiple DDP page sizes to the iSCSI
driver, among other improvements.
Sponsored by: Chelsio Communications
The device quiet flag is not automatically reset on detach, so it is
inherited by other device drivers (e.g. when switching a device driver
over to ppt for PCI pass through). Cope with this behavior by explicitly
marking the device verbose during detach so that the next driver can make
its own decision.
Sponsored by: Chelsio Communications
- Return appropriate error code instead of ENOMEM when sosend() fails in
send_mpa_req.
- Fix for problematic race during destroy_qp.
- Abortive close in the failure of send_mpa_reject() instead of normal close.
- Remove the unnecessary doorbell flowcontrol logic.
Submitted by: Krishnamraju Eraparaju at Chelsio
MFC after: 1 month
Sponsored by: Chelsio communications
hardware send and receive PDU limits. Report these limits to ICL and
take them into account when setting the socket's send and receive buffer
sizes. The driver used a single hardcoded limit everywhere prior to
this change.
Sponsored by: Chelsio Communications
Decouple the send and receive limits on the amount of data in a single
iSCSI PDU. MaxRecvDataSegmentLength is declarative, not negotiated, and
is direction-specific so there is no reason for both ends to limit
themselves to the same min(initiator, target) value in both directions.
Allow iSCSI drivers to report their send, receive, first burst, and max
burst limits explicitly instead of using hardcoded values or trying to
derive all of them from the receive limit (which was the only limit
reported by the drivers prior to this change).
Display the send and receive limits separately in the userspace iSCSI
utilities.
Reviewed by: jpaetzel@ (earlier version), trasz@
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7279
This permits a single early return for VF devices in the routines that
add sysctl nodes.
Reviewed by: np
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7512
Specifically, the FW_PORT_CMD may or may not work for a VF (the PF
driver can choose whether or not to permit access to this command),
so don't attempt to fetch port information on a VF if permission is
denied by the PF.
Reviewed by: np
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7511
While here, mark which parameters are PF-specific and which are
VF-specific.
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7508
- Add handling of VF register sets to t4_get_regs_len() and t4_get_regs().
- While here, use t4_get_regs_len() in the ioctl handler for regdump
instead of inlining it.
Reviewed by: np
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7484
- Use alternate register locations for the data and control registers for
VFs.
- Do a dummy read to force the writes to the mailbox data registers to
post before the write to the control register on VFs.
- Do not check the PCI-e firmware register for errors on VFs.
Reviewed by: np
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7483
Add fields to hold the SGE control register and free list buffer sizes to
the sge_params structure. Populate these new fields in
t4_init_sge_params() for PF devices and change t4_read_chip_settings() to
pull these values out of the params structure instead of reading
registers directly. This will permit t4_read_chip_settings() to be reused
for VF devices which cannot read SGE registers directly.
While here, move the call to t4_init_sge_params() to
get_params__post_init(). The VF driver will populate the SGE parameters
structure via a different method before calling t4_read_chip_settings().
Reviewed by: np
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7476
Use this to map an absolute queue ID to a logical queue ID in interrupt
handlers. For the regular cxgbe/cxl drivers this should be a no-op as
the base absolute ID should be zero. VF devices have a non-zero base
absolute ID and require this change. While here, export the absolute ID
of egress queues via a sysctl.
Reviewed by: np
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7446
Chelsio T4/T5 adapters are multifunction cards. The main driver uses
physical function 4 (PF4). However, VF devices for SR-IOV are only
supported on physical functions 0 through 3, where PF0 creates VFs tied
to port 0, etc. The t4iov/t5iov driver was previously added to
create VF devices for ports that are present on each adapter. This
change uses the recently added pci_iov_attach_name() function to
name the character device in /dev/iov after the associated port on
the card (e.g. /dev/iov/cxl0 is used to create VFs that share the
cxl0 port). With this in place, mark the t4iov/t5iov devices quiet
to prevent them from cluttering dmesg.
Reviewed by: rstone
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7402
VF devices use a different register layout than PF devices. Storing
the offset in a value in the softc allows code to be shared between the
PF and VF drivers.
Reviewed by: np
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7389
- Remove null open/close methods.
- Don't set d_flags to 0 explicitly.
- Remove t5_cdevsw as the .d_name member isn't really used and doesn't
warrant a separate cdevsw just for the name.
- Use ENOTTY as the error value for an unknown ioctl request.
- Use make_dev_s() to close race with setting si_drv1.
Sponsored by: Chelsio Communications
AIO write requests for a TOE socket on a Chelsio T4+ adapter can now
DMA directly from the user-supplied buffer. This is implemented by
wiring the pages backing the user-supplied buffer and queueing special
mbufs backed by raw VM pages to the socket buffer. The TOE code
recognizes these special mbufs and builds a sglist from the VM page
array associated with the mbuf when queueing a work request to the TOE.
Because these mbufs do not have an associated virtual address, m_data
is not valid. Thus, the AIO handler does not invoke sosend() directly
for these mbufs but instead inlines portions of sosend_generic() and
tcp_usr_send().
An aiotx_buffer structure is used to describe the user buffer (e.g.
it holds the array of VM pages and a reference to the AIO job). The
special mbufs reference this structure via m_ext. Note that a single
job might be split across multiple mbufs (e.g. if it is larger than
the socket buffer size). The 'ext_arg2' member of each mbuf gives an
offset relative to the backing aiotx_buffer. The AIO job associated
with an aiotx_buffer structure is completed when the last reference to
the structure is released.
Zero-copy aio_write()'s for connections associated with a given
adapter can be enabled/disabled at runtime via the
'dev.t[45]nex.N.toe.tx_zcopy' sysctl.
MFC after: 1 month
Relnotes: yes
Sponsored by: Chelsio Communications
returning EAGAIN if they aren't available when the user tries to program
a filter. Do this after validating the filter so that the driver
doesn't bring up the queues if it doesn't have to.
Chelsio NICs are a bit unique compared to some other NICs in that they
expose different functionality on different physical functions. In
particular, PF4 is used to manage the NIC interfaces ('t4nex' and 't5nex').
However, PF4 is not able to create VF devices. Instead, VFs are only
supported by physical functions 0 through 3. This commit adds 't4iov'
and 't5iov' drivers that attach to PF0-3.
One extra wrinkle is that the iov devices cannot enable SR-IOV until the
firwmare has been initialized by the main PF4 driver. To handle this
case, a new t4_if kobj interface has been added to permit cross-calls
between the PF drivers. The PF4 driver notifies sibling drivers when it
is fully attached. It also requests sibling drivers to detach before it
detaches. Sibling drivers query the PF4 driver during their attach
routine to see if it is attached. If not, the sibling drivers defer
their attach actions until the PF4 driver informs them it is attached.
VF devices are associated with a single port on the NIC. VF devices
created from PF0 are associated with the first port on the NIC, VFs
from PF1 are associated with the second port, etc. VF devices can
only be created from a PF device that has an associated port. Thus,
on a 2-port card, VFs are only supported on PF0 and PF1.
Reviewed by: np (earlier versions)
MFC after: 1 month
Sponsored by: Chelsio Communications
If a driver sends an malformed or disallowed work request, the firmware
responds with a work request error. Previously the driver treated this is
as an unexpected message and panicked. Now it decodes the error message
to aid in debugging.
Reviewed by: np (older version)
MFC after: 1 month
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D6950
related to "shared" CPLs.
a) Combine t4_set_tcb_field and t4_set_tcb_field_rpl into a single
function. Allow callers to direct the response to any iq. Tidy up
set_ulp_mode_iscsi while there to use names from t4_tcb.h instead of
magic constants.
b) Remove all CPL handler tables from struct adapter. This reduces its
size by around 2KB. All handlers are now registered at MOD_LOAD instead
of attach or some kind of initialization/activation. The registration
functions do not need an adapter parameter any more.
c) Add per-iq handlers to deal with CPLs whose destination cannot be
determined solely from the opcode. There are 2 such CPLs in use right
now: SET_TCB_RPL and L2T_WRITE_RPL. The base driver continues to send
filter and L2T_WRITEs over the mgmtq and solicits the reply on fwq.
t4_tom (including the DDP code) now uses the port's ctrlq to send
L2T_WRITEs and SET_TCB_FIELDs and solicits the reply on an ofld_rxq.
fwq and ofld_rxq have different handlers that know what kind of tid to
expect in the reply. Update t4_write_l2e and callers to to support any
wrq/iq combination.
Approved by: re@ (kib@)
Sponsored by: Chelsio Communications
The interface's queues are functional after VI_INIT_DONE (which is short
of interface-up) and that's all that's needed for t4_tom to communicate
with the chip.
Approved by: re@ (gjb@)
Sponsored by: Chelsio Communications
vcxgbe/vcxl interfaces and retire the 'n' interfaces. The main
cxgbe/cxl interfaces and tunables related to them are not affected by
any of this and will continue to operate as usual.
The driver used to create an additional 'n' interface for every
cxgbe/cxl interface if "device netmap" was in the kernel. The 'n'
interface shared the wire with the main interface but was otherwise
autonomous (with its own MAC address, etc.). It did not have normal
tx/rx but had a specialized netmap-only data path. r291665 added
another set of virtual interfaces (the 'v' interfaces) to the driver.
These had normal tx/rx but no netmap support.
This revision consolidates the features of both the interfaces into the
'v' interface which now has a normal data path, TOE support, and native
netmap support. The 'v' interfaces need to be created explicitly with
the hw.cxgbe.num_vis tunable. This means "device netmap" will not
result in the automatic creation of any virtual interfaces.
The following tunables can be used to override the default number of
queues allocated for each 'v' interface. nofld* = 0 will disable TOE on
the virtual interface and nnm* = 0 to will disable native netmap
support.
# number of normal NIC queues
hw.cxgbe.ntxq_vi
hw.cxgbe.nrxq_vi
# number of TOE queues
hw.cxgbe.nofldtxq_vi
hw.cxgbe.nofldrxq_vi
# number of netmap queues
hw.cxgbe.nnmtxq_vi
hw.cxgbe.nnmrxq_vi
hw.cxgbe.nnm{t,r}xq{10,1}g tunables have been removed.
--- tl;dr version ---
The workflow for netmap on cxgbe starting with FreeBSD 11 is:
1) "device netmap" in the kernel config.
2) "hw.cxgbe.num_vis=2" in loader.conf. num_vis > 2 is ok too, you'll
end up with multiple autonomous netmap-capable interfaces for every
port.
3) "dmesg | grep vcxl | grep netmap" to verify that the interface has
netmap queues.
4) Use any of the 'v' interfaces for netmap. pkt-gen -i vcxl<n>... .
One major improvement is that the netmap interface has a normal data
path as expected.
5) Just ignore the cxl interfaces if you want to use netmap only. No
need to bring them up. The vcxl interfaces are completely independent
and everything should just work.
---------------------
Approved by: re@ (gjb@)
Relnotes: Yes
Sponsored by: Chelsio Communications
File and disk-backed I/O requests store counts of read/written disk
blocks in each AIO job so that they can be charged to the thread that
completes an AIO request via aio_return() or aio_waitcomplete(). This
change extends AIO jobs to store counts of received/sent messages and
updates socket backends to set these counts accordingly. Note that
the socket backends are careful to only charge a single messages for
each AIO request even though a single request on a blocking socket might
invoke sosend or soreceive multiple times. This is to mimic the
resource accounting of synchronous read/write.
Adjust the UNIX socketpair AIO test to verify that the message resource
usage counts update accordingly for aio_read and aio_write.
Approved by: re (hrs)
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D6911
Inserting a full mbuf with an external cluster into the socket buffer
resulted in sbspace() returning -MLEN. However, since sb_hiwat is
unsigned, the -MLEN value was converted to unsigned in comparisons. As a
result, the socket buffer was never autosized. Note that sb_lowat is signed
to permit direct comparisons with sbspace(), but sb_hiwat is unsigned.
Follow suit with what tcp_output() does and compare the value of sbused()
with sb_hiwat instead.
Approved by: re (gjb)
Sponsored by: Chelsio Communications
This reduces the size of kaiocb slightly. I've also added some generic
fields that other backends can use in place of the BIO-specific fields.
Change the socket and Chelsio DDP backends to use 'backend3' instead of
abusing _aiocb_private.status directly. This confines the use of
_aiocb_private to the AIO internals in vfs_aio.c.
Reviewed by: kib (earlier version)
Approved by: re (gjb)
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D6547
Release the hold on ep->com immediately after sending the RST. This
fixes a bug that sometimes leaves userspace iWARP tools hung when the
user presses ^C.
Submitted by: Krishnamraju Eraparaju @ Chelsio
Approved by: re (gjb@)
Sponsored by: Chelsio Communications
- Validate the scheduling class against the actual limit (which is chip
specific) instead of a magic number.
- Return an error if an attempt is made to manipulate the tx queues of a
VI that hasn't been initialized.
Sponsored by: Chelsio Communications
comp_handler_lock but c4iw_destroy_cq has already freed the CQ memory
(which is where the lock resides).
Submitted by: Krishnamraju Eraparaju @ Chelsio
Sponsored by: Chelsio Communications
by default. This is a workaround for a too simplistic ICL module
choosing mechanism. To use it, specify offload in ctl.conf
or iscsi.conf.
This fixes a problem where "kldload cxgbei" wedges the iSCSI stack,
if you don't have a Chelsio card installed, or the endpoints of the
iSCSI session are not reachable through addresses configured
on that interface.
Reviewed by: np@
MFC after: 1 month
avoid panicking debug kernels.
t4_tom does not keep track of a connection once it switches to ULP mode
iWARP. If the connection falls out of ULP mode the driver/hardware seq#
etc. are out of sync. A better fix would be to figure out what the
current seq# are, update the driver's state, and perform all sanity
checks as usual.
If the parent is DEAD or connect_request_upcall() fails, the parent
mutex is left locked. This leads to a hang when process_mpa_request()
is called again for another child of the listening endpoint.
Submitted by: Krishnamraju Eraparaju @ Chelsio
Obtained from: upstream iw_cxgb4
Sponsored by: Chelsio Communications
tunable SYSCTL's. Linux module parameters are associated with the
module they belong to. FreeBSD does not share this concept of a parent
module. Instead add macros which define the prefix to use for the
module parameters in the LinuxKPI consumers.
While at it convert all "bool" LinuxKPI module parameters to "byte"
type, because we don't have a "bool" type of SYSCTL in FreeBSD.
Sponsored by: Mellanox Technologies
MFC after: 1 week
method. This is required for upcoming iSER support.
Obtained from: Mellanox Technologies (earlier version)
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
These firmwares were obtained from the "Chelsio T5/T4 Unified Wire
v2.12.0.3 for Linux" release. Changes since 1.14.4.0 (which is the
firmware in -STABLE branches) are in the "Release Notes" accompanying
the Unified Wire release and are copy-pasted here as well.
22.1. T5 Firmware
+++++++++++++++++++++++++++++++++
Version : 1.15.37.0
Date : 04/27/2016
================================================================================
FIXES
-----
BASE:
- Fixed an issue in FW_RSS_VI_CONFIG_CMD handling where the default ingress
queue was ignored.
- Fixed an issue where adapter failed to load fw by adjusting DRAM frequency.
- Fixed an issue in watchdog which was causing VM bring-up failure after reboot.
- Fixed 40G link failures with some switches when auto-negotiation enabled.
- Fixed to improve on link bring-up time.
- Per port buffer groups size doubled to improve performance.
- Fixed an issue where bogus d3hot bits were set causing traffic stall.
- Fixed an issue where sometimes adapter was not seen after reboot.
- Fixed an issue where iWARP was crashing in conjunction with traffic management.
- Fixed an issue where link failed to come up after removing twinax cable and
inserting optical module.
ETH
- Fixed a link flap issue on T580-CR.
OFLD
- Fixed a potential iSCSI data corruption issue by disabling RxFragEn flag.
FOiSCSI
- Fixed an issue in recovery path where connection was getting closed before
recovery processing was done.
- Fixed an issue in TCP port reuse.
- Fixed an issue in recovery path when large number (>64) of iSCSI connections
were in use.
- Returned ENETUNREACH if IP was not been provisioned yet and driver tried to
use given inerface.
- Fixed an issue where fw was sending ENETUNREACH event for normal tcp
disconnection.
DCBX
- Fixed an issue where iscsi tlv is sent incorrectly to host. (DCBX CEE)
- Fixed an issue where apply bit set for APP id was affecting the ETS and PFC
settings.(DCBX IEEE)
- Fixed an issue where app priority values are not handled correctly in fw.
(DCBX IEEE)
- Fixed an issue where enable/disable dcbx can cause crash. (DCBX CEE,DCBX IEEE)
FOFCoE
- Removed BB6 support.
ENHANCEMENTS
------------
BASE:
- Added new interface to program DCA settings in SGE contexts; allow 32-byte
IQE size
- Added PTP interface fw_ptp_ts to support PTP Frequeny and Offset adjustment.
- Added MPS raw interface.
ETH:
- New mailbox command FW_DCB_IEEE_CMD api added for IEEE dcbx.
OFLD:
- WR opcode is returned to host in cqe error response.
22.2. T4 Firmware
+++++++++++++++++
Version : 1.15.37.0
Date : 04/27/2016
================================================================================
FIXES
-----
BASE:
- Fixed an issue in FW_RSS_VI_CONFIG_CMD handling where default ingress queue
was ignored.
- Fixed an issue in watchdog which was causing VM bring-up failure after reboot.
- Per port buffer groups size doubled to improve performance.
- Fixed an issue where iWARP was crashing in conjunction with traffic management.
FOiSCSI:
- Fixed an issue in recovery path where connection was getting closed before
recovery processing was done.
- Fixed an issue in TCP port reuse.
- Fixed an issue in recovery path when large number (>64) of iSCSI connections
were in use.
- Returned ENETUNREACH if IP had not been provisioned yet and driver tried to
use given inerface.
DCBX
- Fixed an issue where iscsi tlv is sent incorrectly to host.(DCBX CEE)
- Fixed an issue where enable/disable dcbx can cause crash in firmware.(DCBX CEE)
FOiSCSI
- Fixes an issue where fw was sending ENETUNREACH event for normal tcp
disconnection.
FOFCoE
- Removed BB6 support.
ENHANCEMENTS
------------
BASE:
- Added MPS raw interface.
ETH:
- New mailbox command FW_DCB_IEEE_CMD api added for IEEE dcbx.
================================================================================
Obtained from: Chelsio Communications
MFC after: 6 weeks
Relnotes: yes
Sponsored by: Chelsio Communications
Other structures needed by prototypes in t4_tom.h are explicitly
declared in this file, so adding the prototype here seems most
consistent with existing code.
Chelsio's TCP offload engine supports direct DMA of received TCP payload
into wired user buffers. This feature is known as Direct-Data Placement.
However, to scale well the adapter needs to prepare buffers for DDP
before data arrives. aio_read() is more amenable to this requirement than
read() as applications often call read() only after data is available in
the socket buffer.
When DDP is enabled, TOE sockets use the recently added pru_aio_queue
protocol hook to claim aio_read(2) requests instead of letting them use
the default AIO socket logic. The DDP feature supports scheduling DMA
to two buffers at a time so that the second buffer is ready for use
after the first buffer is filled. The aio/DDP code optimizes the case
of an application ping-ponging between two buffers (similar to the
zero-copy bpf(4) code) by keeping the two most recently used AIO buffers
wired. If a buffer is reused, the aio/DDP code is able to reuse the
vm_page_t array as well as page pod mappings (a kind of MMU mapping the
Chelsio NIC uses to describe user buffers). The generation of the
vmspace of the calling process is used in conjunction with the user
buffer's address and length to determine if a user buffer matches a
previously used buffer. If an application queues a buffer for AIO that
does not match a previously used buffer then the least recently used
buffer is unwired before the new buffer is wired. This ensures that no
more than two user buffers per socket are ever wired.
Note that this feature is best suited to applications sending a steady
stream of data vs short bursts of traffic.
Discussed with: np
Relnotes: yes
Sponsored by: Chelsio Communications
rounddown2 tends to produce longer lines than the original code
and when the code has a high indentation level it was not really
advantageous to do the replacement.
This tries to strike a balance between readability using the macros
and flexibility of having the expressions, so not everything is
converted.
The size of the reply can be different from the size of the command in
case a debug firmware asserts. fw_asrt() needs the entire reply in
order to decode the location of the assert.
Sponsored by: Chelsio Communications
This fixes a conflict with the M_B macro in powerpc's
<machine/db_machdep.h> exposed by the recent addition of DDB commands
to the cxgbe driver.
Discussed with: np
Reported by: bz
Sponsored by: Chelsio Communications
And factor out tcp_lro_rx_done, which deduplicates the same logic with
netinet/tcp_lro.c
Reviewed by: gallatin (1st version), hps, zbb, np, Dexuan Cui <decui microsoft com>
Sponsored by: Microsoft OSTC
Differential Revision: https://reviews.freebsd.org/D5725
This provides a constant ABI and layout for these structures (especially
struct adapter) avoiding some foot shooting.
Discussed with: np
Sponsored by: Chelsio Communications
Figure out if the chip is counting PAUSE frames in the "normal" stats
and take them out if it is. This fixes a bug in the tx stats because
the default hardware behavior is different for Tx and Rx but the driver
was treating both the same way. The result was that OPACKETS, OBYTES,
and OMCASTS were under-reported (if tx_pause > 0) before this change.
Note that the mac_stats sysctl still gives you the raw value of these
statistics straight from the device registers.
defined:
sys/dev/cxgbe/t4_main.c:7474: warning: 'sysctl_tp_tick' defined but not used
sys/dev/cxgbe/t4_main.c:7505: warning: 'sysctl_tp_dack_timer' defined but not used
sys/dev/cxgbe/t4_main.c:7519: warning: 'sysctl_tp_timer' defined but not used
This just adds a bunch of #ifdef TCP_OFFLOAD in the right places.
Reviewed by: np
Differential Revision: https://reviews.freebsd.org/D5620
- Query the location of the log very early during attach. Refresh the
location later after establishing contact with the firmware.
- Save the log's location as a flat address in devlog_params.
- Use a memory window instead of backdoor access to the EDC/MC to read
the log.
