some times compiler inserts redundant instructions to preserve unused upper
32 bits even when it is casted to a 32-bit value. Unfortunately, it seems
the problem becomes more serious when it is shifted, especially on amd64.
- Re-add accidentally removed atomic op. for sysctl(9) handler.
- Remove a period(`.') at the end of a debugging message.
- Consistently spell "low" for "TSC-low" timecounter throughout.
Pointed out by: bde
invariant. For SMP case (TSC-low), it also has to pass SMP synchronization
test and the CPU vendor/model has to be white-listed explicitly. Currently,
all Intel CPUs and single-socket AMD Family 15h processors are listed here.
Discussed with: hackers
TSC timecounter if TSC frequency is higher than ~4.29 MHz (or 2^32-1 Hz) or
multiple CPUs are present. The "TSC-low" frequency is always lower than a
preset maximum value and derived from TSC frequency (by being halved until
it becomes lower than the maximum). Note the maximum value for SMP case is
significantly lower than UP case because we want to reduce (rare but known)
"temporal anomalies" caused by non-serialized RDTSC instruction. Normally,
it is still higher than "ACPI-fast" timecounter frequency (which was default
timecounter hardware for long time until r222222) to be useful.
when the user has indicated that the system has synchronized TSCs or it has
P-state invariant TSCs. For the former case, we may clear the tunable if it
fails the test to prevent accidental foot-shooting. For the latter case, we
may set it if it passes the test to notify the user that it may be usable.
versions instead. They were never needed as bus_generic_intr() and
bus_teardown_intr() had been changed to pass the original child device up
in 42734, but the ISA bus was not converted to new-bus until 45720.
This fixes heavy interrupt storm and resulting system freeze when using
LAPIC timer in one-shot mode under Xen HVM. There, unlike real hardware,
programming timer with zero period almost immediately causes interrupt.
cpuset_t objects.
That is going to offer the underlying support for a simple bump of
MAXCPU and then support for number of cpus > 32 (as it is today).
Right now, cpumask_t is an int, 32 bits on all our supported architecture.
cpumask_t on the other side is implemented as an array of longs, and
easilly extendible by definition.
The architectures touched by this commit are the following:
- amd64
- i386
- pc98
- arm
- ia64
- XEN
while the others are still missing.
Userland is believed to be fully converted with the changes contained
here.
Some technical notes:
- This commit may be considered an ABI nop for all the architectures
different from amd64 and ia64 (and sparc64 in the future)
- per-cpu members, which are now converted to cpuset_t, needs to be
accessed avoiding migration, because the size of cpuset_t should be
considered unknown
- size of cpuset_t objects is different from kernel and userland (this is
primirally done in order to leave some more space in userland to cope
with KBI extensions). If you need to access kernel cpuset_t from the
userland please refer to example in this patch on how to do that
correctly (kgdb may be a good source, for example).
- Support for other architectures is going to be added soon
- Only MAXCPU for amd64 is bumped now
The patch has been tested by sbruno and Nicholas Esborn on opteron
4 x 12 pack CPUs. More testing on big SMP is expected to came soon.
pluknet tested the patch with his 8-ways on both amd64 and i386.
Tested by: pluknet, sbruno, gianni, Nicholas Esborn
Reviewed by: jeff, jhb, sbruno
driver would verify that requests for child devices were confined to any
existing I/O windows, but the driver relied on the firmware to initialize
the windows and would never grow the windows for new requests. Now the
driver actively manages the I/O windows.
This is implemented by allocating a bus resource for each I/O window from
the parent PCI bus and suballocating that resource to child devices. The
suballocations are managed by creating an rman for each I/O window. The
suballocated resources are mapped by passing the bus_activate_resource()
call up to the parent PCI bus. Windows are grown when needed by using
bus_adjust_resource() to adjust the resource allocated from the parent PCI
bus. If the adjust request succeeds, the window is adjusted and the
suballocation request for the child device is retried.
When growing a window, the rman_first_free_region() and
rman_last_free_region() routines are used to determine if the front or
end of the existing I/O window is free. From using that, the smallest
ranges that need to be added to either the front or back of the window
are computed. The driver will first try to grow the window in whichever
direction requires the smallest growth first followed by the other
direction if that fails.
Subtractive bridges will first attempt to satisfy requests for child
resources from I/O windows (including attempts to grow the windows). If
that fails, the request is passed up to the parent PCI bus directly
however.
The PCI-PCI bridge driver will try to use firmware-assigned ranges for
child BARs first and only allocate a "fresh" range if that specific range
cannot be accommodated in the I/O window. This allows systems where the
firmware assigns resources during boot but later wipes the I/O windows
(some ACPI BIOSen are known to do this) to "rediscover" the original I/O
window ranges.
The ACPI Host-PCI bridge driver has been adjusted to correctly honor
hw.acpi.host_mem_start and the I/O port equivalent when a PCI-PCI bridge
makes a wildcard request for an I/O window range.
The new PCI-PCI bridge driver is only enabled if the NEW_PCIB kernel option
is enabled. This is a transition aide to allow platforms that do not
yet support bus_activate_resource() and bus_adjust_resource() in their
Host-PCI bridge drivers (and possibly other drivers as needed) to use the
old driver for now. Once all platforms support the new driver, the
kernel option and old driver will be removed.
PR: kern/143874 kern/149306
Tested by: mav
constraints on the rman and reject attempts to manage a region that is out
of range.
- Fix various places that set rm_end incorrectly (to ~0 or ~0u instead of
~0ul).
- To preserve existing behavior, change rman_init() to set rm_start and
rm_end to allow managing the full range (0 to ~0ul) if they are not set by
the caller when rman_init() is called.
VMware products virtualize TSC and it run at fixed frequency in so-called
"apparent time". Although virtualized i8254 also runs in apparent time, TSC
calibration always gives slightly off frequency because of the complicated
timer emulation and lost-tick correction mechanism.
disk dumping.
With the option SW_WATCHDOG on, these operations are doomed to let
watchdog fire, fi they take too long.
I implemented the stubs this way because I really want wdog_kern_*
KPI to not be dependant by SW_WATCHDOG being on (and really, the option
only enables watchdog activation in hardclock) and also avoid to
call them when not necessary (avoiding not-volountary watchdog
activations).
Sponsored by: Sandvine Incorporated
Discussed with: emaste, des
MFC after: 2 weeks
invariant and APERF/MPERF MSRs exist but these MSRs never tick. When we
calculate effective frequency from cpu_est_clockrate(), it caused panic of
division-by-zero. Now we test whether these MSRs actually increase to avoid
such foot-shooting.
Reported by: dim
Tested by: dim
safer for i386 because it can be easily over 4 GHz now. More worse, it can
be easily changed by user with 'machdep.tsc_freq' tunable (directly) or
cpufreq(4) (indirectly). Note it is intentionally not used in performance
critical paths to avoid performance regression (but we should, in theory).
Alternatively, we may add "virtual TSC" with lower frequency if maximum
frequency overflows 32 bits (and ignore possible incoherency as we do now).
started to execute, it seems that the corresponding ISR bit in the "old"
local APIC can be cleared. This causes the local APIC interrupt routine
to fail to find an interrupt to service. Rather than panic'ing in this
case, simply return from the interrupt without sending an EOI to the
local APIC. If there are any other pending interrupts in other ISR
registers, the local APIC will assert a new interrupt.
Tested by: steve
bus_size_t may be 32 or 64 bits. Change the bounce_zone alignment field
to explicitly be 32 bits, as I can't really imagine a DMA device that
needs anything close to 2GB alignment of data.
interrupt in the I/O APIC before moving it to a different CPU. If the
interrupt had been triggered by the I/O APIC after locking icu_lock but
before we masked the pin in the I/O APIC, then this could cause the
interrupt to be pending on the "old" CPU and it would finally trigger
after we had moved the interrupt to the new CPU. This could cause us to
panic as there was no interrupt source associated with the old IDT vector
on the old CPU. Dropping the lock after the interrupt is masked but
before it is moved allows the interrupt to fire and be handled in this
case before it is moved.
Tested by: Daniel Braniss danny of cs huji ac il
MFC after: 1 week
the original amd64 and i386 headers with stubs.
Rename (AMD64|I386)_BUS_SPACE_* to X86_BUS_SPACE_* everywhere.
Reviewed by: imp (previous version), jhb
Approved by: kib (mentor)
- Avoid side-effect assignments in if statements when possible.
- Don't use ! to check for NULL pointers, explicitly check against NULL.
- Explicitly check error return values against 0.
- Don't use INTR_MPSAFE for interrupt handlers with only filters as it is
meaningless.
- Remove unneeded function casts.
Also, add a comment mentioning _PSD - on some systems it's enough to
put one logical CPU into a particular P-state to make other CPUs in
the same domain to enter that P-state.
Also, call sched_unbind() after the loop - sched_bind() automatically
rebinds from previous CPU to a new one, and the new arrangement of code
is safer against early loop exit.
Plus one minor style nit.
MFC after: 10 days
- Register APIC enumerators at SI_SUB_TUNABLES - 1 instead of SI_SUB_CPU - 1.
- Probe CPUs at SI_SUB_TUNABLES - 1. This allows i386 to set a truly
accurate mp_maxid value rather than always setting it to MAXCPU - 1.
local APIC if those LVT entries are valid. This quiets spurious illegal
register local APIC errors during boot on a CPU that doesn't support those
vectors.
MFC after: 1 week
- Use > 2^32 - 1 instead of >= when checking for memory regions above 4G.
- Skip SMAP entries > 4G on i386 rather than breaking out of the loop
since SMAP entries are not guaranteed to be in order.
- Remove 'i' and loop over 'rid' directly in the dump_avail[] case.
- Only check for 4G regions in the dump_avail[] case on i386 if PAE is
enabled since vm_paddr_t is 32-bit in the !PAE case.
Submitted by: alc
- Rename RES_BUS_SPACE_* into BUS_SPACE_* for consistency
- Trim out an unnecessary checking condition
Sponsored by: Sandvine Incorporated
Requested and reviewed by: jhb
Old scrolls tell that once upon a time IBM AT BIOS was known to put some
useful system diagnostic information into RTC NVRAM. It is not really
known if and for how long PC BIOSes followed that convention, but I
believe that many, if not all, modern BIOSes do not do that any more
(not mentioning other types of x86 firmware).
Some diagnostic bits don't even make any sense any longer.
The check results in confusing messages upon boot on some systems.
So I am removing it.
Discussed with: bde, jhb, mav
MFC after: 3 weeks
not neccessary. It allows to avoid time counter jump of up to 1/18s, when
base frequency slightly tuned via machdep.i8254_freq sysctl.
Fix few style things.
Suggested by: bde
Unluckily, using one-shot mode is impossible, when same hardware used for
time counting. Introduce new tunable hint.attimer.0.timecounter, setting
which to 0 disables i8254 time counter and allows one-shot mode. Note,
that on some systems there may be no other reliable enough time counters,
so this tunable should be used with understanding.
The main goal of this is to generate timer interrupts only when there is
some work to do. When CPU is busy interrupts are generating at full rate
of hz + stathz to fullfill scheduler and timekeeping requirements. But
when CPU is idle, only minimum set of interrupts (down to 8 interrupts per
second per CPU now), needed to handle scheduled callouts is executed.
This allows significantly increase idle CPU sleep time, increasing effect
of static power-saving technologies. Also it should reduce host CPU load
on virtualized systems, when guest system is idle.
There is set of tunables, also available as writable sysctls, allowing to
control wanted event timer subsystem behavior:
kern.eventtimer.timer - allows to choose event timer hardware to use.
On x86 there is up to 4 different kinds of timers. Depending on whether
chosen timer is per-CPU, behavior of other options slightly differs.
kern.eventtimer.periodic - allows to choose periodic and one-shot
operation mode. In periodic mode, current timer hardware taken as the only
source of time for time events. This mode is quite alike to previous kernel
behavior. One-shot mode instead uses currently selected time counter
hardware to schedule all needed events one by one and program timer to
generate interrupt exactly in specified time. Default value depends of
chosen timer capabilities, but one-shot mode is preferred, until other is
forced by user or hardware.
kern.eventtimer.singlemul - in periodic mode specifies how much times
higher timer frequency should be, to not strictly alias hardclock() and
statclock() events. Default values are 2 and 4, but could be reduced to 1
if extra interrupts are unwanted.
kern.eventtimer.idletick - makes each CPU to receive every timer interrupt
independently of whether they busy or not. By default this options is
disabled. If chosen timer is per-CPU and runs in periodic mode, this option
has no effect - all interrupts are generating.
As soon as this patch modifies cpu_idle() on some platforms, I have also
refactored one on x86. Now it makes use of MONITOR/MWAIT instrunctions
(if supported) under high sleep/wakeup rate, as fast alternative to other
methods. It allows SMP scheduler to wake up sleeping CPUs much faster
without using IPI, significantly increasing performance on some highly
task-switching loads.
Tested by: many (on i386, amd64, sparc64 and powerc)
H/W donated by: Gheorghe Ardelean
Sponsored by: iXsystems, Inc.
"uncore" devices (such as the memory controller) in that socket. Stop
hardcoding support for two busses, but instead start probing buses at
domain 0, bus 255 and walk down until a bus probe fails. Also, do not probe
a bus if it has already been enumerated elsewhere (e.g. if ACPI ever
enumerates these buses in the future).
provide PCI devices for various hardware such as memory controllers, etc.
These PCI buses are not enumerated via ACPI however. Add qpi(4) psuedo
bus and Host-PCI bridge drivers to enumerate these buses. Currently the
driver uses the CPU ID to determine the bridges' presence.
In collaboration with: Joseph Golio @ Isilon Systems
MFC after: 2 weeks
lengths. Make MI wrapper code to validate periods in request. Make kernel
clock management code to honor these hardware limitations while choosing hz,
stathz and profhz values.
HPET to steal IRQ0 from i8254 and IRQ8 from RTC timers. It can be suitable
for HPETs without FSB interrupts support, as it gives them two unshared
IRQs. It allows them to provide one per-CPU event timer on dual-CPU system,
that should be suitable for further tickless kernels.
To enable it, such lines may be added to /boot/loader.conf:
hint.atrtc.0.clock=0
hint.attimer.0.clock=0
hint.hpet.0.legacy_route=1
writing event timer drivers, for choosing best possible drivers by machine
independent code and for operating them to supply kernel with hardclock(),
statclock() and profclock() events in unified fashion on various hardware.
Infrastructure provides support for both per-CPU (independent for every CPU
core) and global timers in periodic and one-shot modes. MI management code
at this moment uses only periodic mode, but one-shot mode use planned for
later, as part of tickless kernel project.
For this moment infrastructure used on i386 and amd64 architectures. Other
archs are welcome to follow, while their current operation should not be
affected.
This patch updates existing drivers (i8254, RTC and LAPIC) for the new
order, and adds event timers support into the HPET driver. These drivers
have different capabilities:
LAPIC - per-CPU timer, supports periodic and one-shot operation, may
freeze in C3 state, calibrated on first use, so may be not exactly precise.
HPET - depending on hardware can work as per-CPU or global, supports
periodic and one-shot operation, usually provides several event timers.
i8254 - global, limited to periodic mode, because same hardware used also
as time counter.
RTC - global, supports only periodic mode, set of frequencies in Hz
limited by powers of 2.
Depending on hardware capabilities, drivers preferred in following orders,
either LAPIC, HPETs, i8254, RTC or HPETs, LAPIC, i8254, RTC.
User may explicitly specify wanted timers via loader tunables or sysctls:
kern.eventtimer.timer1 and kern.eventtimer.timer2.
If requested driver is unavailable or unoperational, system will try to
replace it. If no more timers available or "NONE" specified for second,
system will operate using only one timer, multiplying it's frequency by few
times and uing respective dividers to honor hz, stathz and profhz values,
set during initial setup.
core lower then set on other cores. Do not try to test P-states on attach
on SMP systems. It is hopeless now and will just pollute verbose logs.
If needed, check still can be forced via loader tunable.
APIC interrupt that fires when a threshold of corrected machine check
events is reached. CMCI also includes a count of events when reporting
corrected errors in the bank's status register. Note that individual
banks may or may not support CMCI. If they do, each bank includes its own
threshold register that determines when the interrupt fires. Currently
the code uses a very simple strategy where it doubles the threshold on
each interrupt until it succeeds in throttling the interrupt to occur
only once a minute (this interval can be tuned via sysctl). The threshold
is also adjusted on each hourly poll which will lower the threshold once
events stop occurring.
Tested by: Sailaja Bangaru sbappana at yahoo com
MFC after: 1 month
arbitrary frequencies into hardclock(), statclock() and profclock() calls.
Same code with minor variations duplicated several times over the tree for
different timer drivers and architectures.
- Switch all x86 archs to new functions, simplifying the code and removing
extra logic from timer drivers. Other archs are also welcome.
broken atrtc.
Now if you want more correct stats on profhz and stathz it may be
disabled by setting to 0.
Reported by: A. Akephalos <akephalos dot akephalos at gmail dot com>,
Jakub Lach <jakub_lach at mailplus dot pl>
MFC: 1 week
correctly initialized and just then assign to softclock/profclock.
Right now, some atrtc seems reporting strange diagnostic error* making the
current pattern bogus.
In order to do that cleanly, lapic_setup_clock(), on both ia32 and amd64,
now accepts as arguments the desired sources to handle, and returns the
actual ones (LAPIC_CLOCK_NONE is forbidden because otherwise there is no
meaning in calling such function).
This allows to bring out into commont x86 code the handling part for
machdep.lapic_allclocks tunable, which is retained.
Sponsored by: Sandvine Incorporated
Tested by: yongari, Richard Todd
<rmtodd at ichotolot dot servalan dot com>
MFC: 3 weeks
X-MFC: r202387, 204309
shared and generalized between our current amd64, i386 and pc98.
This is just an initial step that should lead to a more complete effort.
For the moment, a very simple porting of cpufreq modules, BIOS calls and
the whole MD specific ISA bus part is added to the sub-tree but ideally
a lot of code might be added and more shared support should grow.
Sponsored by: Sandvine Incorporated
Reviewed by: emaste, kib, jhb, imp
Discussed on: arch
MFC: 3 weeks
