This takes the SPCR code currently in uart_cpu_arm64.c, moves it into
a new uart_cpu_acpi.c (with some associated refactoring), and uses it
from both arm64 and x86.
An SPCR serial port address AccessWidth field value of 0 ("reserved")
is now treated as 1 ("byte access") in order to work around a buggy
SPCR table on Amazon EC2 i3.metal instances.
Reviewed by: manu, Greg V
MFC after: 3 days
Sponsored by: https://www.patreon.com/cperciva
Differential Revision: https://reviews.freebsd.org/D20357
From 7d8dc6544c
"The mcbin (and likely others) have a nonstandard uart clock. This means
that the earlycon programming will incorrectly set the baud rate if it is
specified. The way around this is to tell the kernel to continue using the
preprogrammed baud rate. This is done by setting the baud to 0."
Our drivers (uart_dev_ns8250) do respect zero, but SPCR would error. Let's
not error.
Submitted by: Greg V <greg@unrelenting.technology>
Reviewed by: mw, imp, bcran
Differential Revision: https://reviews.freebsd.org/D19914
The SPCR table on the Lenovo HR330A Ampere eMAG server indicates 8-bit
access, but 32-bit access is required for the PL011 to work.
PL011 on SBSA platforms always supports 32-bit access (and that was
hardcoded here before my EC2 fix), let's use 32-bit access for PL011
and 32BIT interface types.
Tested by emaste on Ampere eMAG and Cavium/Marvell ThunderX2.
Submitted by: Greg V <greg@unrelenting.technology>
Reviewed by: andrew, imp (earlier)
Differential Revision: https://reviews.freebsd.org/D19507
This value was being used uninitialized, resulting in predictable issues
on systems with memory-mapped UART registers.
A case could be made that memmap_bus should be declared in a header
rather than being declared in each .c file which needs to refer to it,
but that's a broader style question.
This commit unbreaks hw.uart.console="mm:..." on ARM64.
Submitted by: Greg V
The "access width" value was hard-coded as 2, indicating 32-bit accesses;
instead, use the value specified in the SPCR table.
This unbreaks the console on EC2 "A1" family instances.
Submitted by: Greg V
as an NS8250 UART.
This is the same as the UART found in EC2 "bare metal" instances,
except that the card vendor shows up as 0x0000 rather than 0x1d0f.
This seems like a bug in the EC2 firmware; but we might as well support
it anyway.
Reported by: Greg V
The only source of documentation for this device is verilog,
so driver is minimalistic.
Reviewed by: Dr Jonathan Kimmitt <jrrk2@cam.ac.uk>
Approved by: re (kib)
Sponsored by: DARPA, AFRL
Recent changes in Linux updated Marvell Armada 38x
UART compatible string. As a result the FreeBSD driver
(uart_dev_snps) does not probe. This commit fixes the
situation, however not applying any functional modification
to the driver methods.
Approved by: re (kib)
Obtained from: Semihalf
Remove unused and easy to misuse PNP macro parameter
Inspired by r338025, just remove the element size parameter to the
MODULE_PNP_INFO macro entirely. The 'table' parameter is now required to
have correct pointer (or array) type. Since all invocations of the macro
already had this property and the emitted PNP data continues to include the
element size, there is no functional change.
Mostly done with the coccinelle 'spatch' tool:
$ cat modpnpsize0.cocci
@normaltables@
identifier b,c;
expression a,d,e;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,d,
-sizeof(d[0]),
e);
@singletons@
identifier b,c,d;
expression a;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,&d,
-sizeof(d),
1);
$ rg -l MODULE_PNP_INFO -- sys | \
xargs spatch --in-place --sp-file modpnpsize0.cocci
(Note that coccinelle invokes diff(1) via a PATH search and expects diff to
tolerate the -B flag, which BSD diff does not. So I had to link gdiff into
PATH as diff to use spatch.)
Tinderbox'd (-DMAKE_JUST_KERNELS).
Approved by: re (glen)
This is an amalgam of a patch by Doug Ambrisko to
generalize uart_acpi_find_device, imp moving the
ACPI table to uart_dev_ns8250.c and advice by jhb
to work around a bug in the EPYC 3151 BIOS
(the BIOS incorrectly marks the serial ports as
disabled)
Reviewed by: imp
MFC after: 8 weeks
Differential Revision: https://reviews.freebsd.org/D16432
I was not aware Warner was making or planning to make forward progress in
this area and have since been informed of that.
It's easy to apply/reapply when churn dies down.
Inspired by r338025, just remove the element size parameter to the
MODULE_PNP_INFO macro entirely. The 'table' parameter is now required to
have correct pointer (or array) type. Since all invocations of the macro
already had this property and the emitted PNP data continues to include the
element size, there is no functional change.
Mostly done with the coccinelle 'spatch' tool:
$ cat modpnpsize0.cocci
@normaltables@
identifier b,c;
expression a,d,e;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,d,
-sizeof(d[0]),
e);
@singletons@
identifier b,c,d;
expression a;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,&d,
-sizeof(d),
1);
$ rg -l MODULE_PNP_INFO -- sys | \
xargs spatch --in-place --sp-file modpnpsize0.cocci
(Note that coccinelle invokes diff(1) via a PATH search and expects diff to
tolerate the -B flag, which BSD diff does not. So I had to link gdiff into
PATH as diff to use spatch.)
Tinderbox'd (-DMAKE_JUST_KERNELS).
This change allows one to set the busy_detect flag
required by the synopsys UART at the loader prompt.
This is needed by the EPYC 3000 SoC.
This will give users a working console up to the point where getty is required:
hw.uart.console="mm:0xfedc9000,rs:2,bd:1"
Reviewed by: imp
MFC after: 4 weeks
Differential Revision: https://reviews.freebsd.org/D16399
This change adds a new optional console method cn_resume and a kernel
console interface cnresume. Consoles that may need to re-initialize
their hardware after suspend (e.g., because firmware does not care to do
it) will implement cn_resume. Note that it is called in rather early
environment not unlike early boot, so the same restrictions apply.
Platform specific code, for platforms that support hardware suspend,
should call cnresume early after resume, before any console output is
expected.
This change fixes a problem with a system of mine failing to resume when
a serial console is used. I found that the serial port was in a strange
configuration and an attempt to write to it likely resulted in an
infinite loop.
To avoid adding cn_resume method to every console driver, CONSOLE_DRIVER
macro has been extended to support optional methods.
Reviewed by: imp, mav
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D15552
Move the allwinner early printf support to the snps driver as it
should work with all implementation.
While here add instruction for enabling it on 64bits SoCs.
opt_compat.h is mentioned in nearly 180 files. In-progress network
driver compabibility improvements may add over 100 more so this is
closer to "just about everywhere" than "only some files" per the
guidance in sys/conf/options.
Keep COMPAT_LINUX32 in opt_compat.h as it is confined to a subset of
sys/compat/linux/*.c. A fake _COMPAT_LINUX option ensure opt_compat.h
is created on all architectures.
Move COMPAT_LINUXKPI to opt_dontuse.h as it is only used to control the
set of compiled files.
Reviewed by: kib, cem, jhb, jtl
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14941
It calls OF_* functions to check if it needs to implement workarounds.
This may not be the case on arm64 where we support both FDT and ACPI.
Fix this by checking if we are booting on FDT before calling these checks.
Reviewed by: ian
Sponsored by: DARPA, AFRL
Sponsored by: Cavium (Hardware)
Differential Revision: https://reviews.freebsd.org/D14515
the Server Base System Architecture to be a subset of the pl011 r1p5. As
we don't use the removed features it is safe to just attach to the existing
driver as is.
Sponsored by: DARPA, AFRL
This reduces noise when kernel is compiled by newer GCC versions,
such as one used by external toolchain ports.
Reviewed by: kib, andrew(sys/arm and sys/arm64), emaste(partial), erj(partial)
Reviewed by: jhb (sys/dev/pci/* sys/kern/vfs_aio.c and sys/kern/kern_synch.c)
Differential Revision: https://reviews.freebsd.org/D10385
ISA PNP card support (replace by hand version in if_ed). Move module
declarations to the end of some files. Fix PCCARD_PNP_INFO to use
nitems(). Remove some stale comments about pc98, turns out the comment
was simply wrong.
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
This patch adds support for UART in Armada 3700 family.
It exposes both low-level UART interface, as well as
standard driver methods.
Submitted by: Patryk Duda <pdk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Semihalf
Differential Revision: https://reviews.freebsd.org/D12250
The stdout-path chosen property may include the serial connection details,
e.g. the baud rate. When passing the device to OF_finddevice we need to
strip off this information as it will cause the lookup to fail.
Reviewed by: emaste, manu
Differential Revision: https://reviews.freebsd.org/D6846
At least with Tx FIFO enabled it shows me ~10% reduction of verbose boot
time with serial console at 115200 baud.
Reviewed by: marcel
MFC after: 2 weeks
hardware but lack the larger fifos rev 5 hardware should have.
The linux world (where our FDT data comes from) solved this by adding
a new property to pl011 nodes, "arm,primecell-periphid". When this
property is present, its values override the values in the hardware
periphid registers. For pl011 rev 5 hardware with small fifos, they
override the id so that it appears to be rev 4 hardware.
The driver now uses the new property when present. It also continues
to check the device compat string, to handle older fdt data that may
still be in use on existing systems (on RPi systems it is common to
update system software without updating fdt data which is part of the
boot firmware).
Reviewed by: imp
Starting with rev 5 (which is inexplicably indicated by a version number
of '3' in the Peripheral ID register), the pl011 doubled the size of the
rx and tx fifos, to 32 bytes, so read the ID register and set the size
variables in the softc accordingly.
An interesting wrinkle in this otherwise-simple concept is that the
bcm2835 SoC, used in Raspberry Pi systems among others, has the rev 5
pl011 hardware, but somehow also has the older 16-byte fifos. We check
the FDT data to see if the hardware is part of a bcm283x system and use
the smaller size if so.
Thanks to jchandra@ for pointing out that newer hardware has bigger fifos.
have been in the code all along, but were masked by having a fifo depth of
one byte at the hardware level, so everything kinda worked by accident.
The hardware interrupts when the TX fifo is half empty, so set
sc->sc_txfifosz to 8 bytes (half the hardware fifo size) to match. This
eliminates dropped characters on output.
Restructure the read loop to consume all the bytes in the fifo by using
the "rx fifo empty" bit of the flags register rather than the "rx ready"
bit of the interrupt status register. The rx-ready interrupt is cleared
when the number of bytes in the fifo fall below the interrupt trigger
level, leaving the fifo half full every time receive routine was called.
Now it loops until the fifo is completely empty every time (including
when the function is called due to a receive timeout as well as for
fifo-full).
This is required for FDT's standard "reg-io-width" property
(similar to "reg-shift" property) found in many DTS files.
This fixes operation on Altera Arria 10 SOC Development Kit,
where standard ns8250 uart allows 4-byte access only.
Reviewed by: kan, marcel
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D9785
The pl011 UART has a 16 entry Tx FIFO and a 16 entry Rx FIFO that
have not been used so far. Update the driver to enable the FIFOs
and use them in transmit and receive.
Reviewed by: andrew
Differential Revision: https://reviews.freebsd.org/D8819
