compiled into the kernel. This allows us to boot the same kernel on
machines with different master clock frequencies, so long as we can
determine the main clock frequency accurately. Cleanup the pmc clock
init function so it can be called in early boot so we can use the
serial port just after we call cninit.
# We have two calls to at91_pmc_clock_init for reasons unknown, that will
# be fixed later -- it is harmless for now.
DataFlash.
- Add a mapping for the Nut/OS configuration DataFlash partition according
to the board manual (but not known to either Linux or U-Boot (patches).
in_cksum.h required ip.h to be included for struct ip. To be
able to use some general checksum functions like in_addword()
in a non-IPv4 context, limit the (also exported to user space)
IPv4 specific functions to the times, when the ip.h header is
present and IPVERSION is defined (to 4).
We should consider more general checksum (updating) functions
to also allow easier incremental checksum updates in the L3/4
stack and firewalls, as well as ponder further requirements by
certain NIC drivers needing slightly different pseudo values
in offloading cases. Thinking in terms of a better "library".
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
Reviewed by: gnn (as part of the whole)
MFC After: 3 days
frequency in the at91_pmc_clock_init rather than passing it in. Allow
for frequencies >= 21MHz by rounding to the nearest 500Hz (Idea from
Ian Lapore whose company uses a similar arrangement in their product).
at91_pmc_clock_init() is now nearly independent of the rest of the pmc
driver (which means we may be able to call it much earlier in boot
soon to eliminate the master clock config file requirement for printf
to work during early boot and also eliminate some interdependencies
with the device ordering which requires pmc to be the first device
added).
all integrated and on-board peripherals except the DataFlash (at91_spi(4)
and at45d(4) still need to be unb0rken) and NAND Flash (missing NAND
framework) are working.
AFAICT, this makes FreeBSD the first operating system besides Nut/OS
supporting Ethernut 5 out of tree.
ports. This currently is a nop, but will soon be used to allow
support for multiple boards to be built into one kernel (starting with
AT91RM9200 and expanding out from there).
- Align the RX buffers on the cache line size, otherwise the requirement
of partial cache line flushes on every are pretty much guaranteed. [1]
- Make the code setting the RX timeout match its comment (apparently,
start and stop bits were missed in the previous calculation). [1]
- Cover the busdma operations in at91_usart_bus_{ipend,transmit}() with
the hardware mutex, too, so these don't race against each other.
- In at91_usart_bus_ipend(), reduce duplication in the code dealing with
TX interrupts.
- In at91_usart_bus_ipend(), turn the code dealing with RX interrupts
into an else-if cascade in order reduce its complexity and to improve
its run-time behavior.
- In at91_usart_bus_ipend(), add missing BUS_DMASYNC_PREREAD calls on
the RX buffer map before handing things over to the hardware again. [1]
- In at91_usart_bus_getsig(), used a variable of sufficient width for
storing the contents of USART_CSR.
- Use KOBJMETHOD_END.
- Remove an unused header.
Submitted by: Ian Lepore [1]
Reviewed by: Ian Lepore
MFC after: 1 week
as otherwise the interrupt handling code may modify data in the non-DMA
part of the cache line while we have it stashed away in the temporary
stack buffer, then we end up restoring a stale value.
PR: 160431
Submitted by: Ian Lepore
MFC after: 1 week
used in the code which needs to implement some specific
behaviour when being run under QEMU.
- Make PXA UART probe code to work under QEMU gumstix, which
doesn't emulate all the ports properly.
New kernel events can be added at various location for sampling or counting.
This will for example allow easy system profiling whatever the processor is
with known tools like pmcstat(8).
Simultaneous usage of software PMC and hardware PMC is possible, for example
looking at the lock acquire failure, page fault while sampling on
instructions.
Sponsored by: NETASQ
MFC after: 1 month
As of FreeBSD 8, this driver should not be used. Applications that use
posix_openpt(2) and openpty(3) use the pts(4) that is built into the
kernel unconditionally. If it turns out high profile depend on the
pty(4) module anyway, I'd rather get those fixed. So please report any
issues to me.
The pty(4) module is still available as a kernel module of course, so a
simple `kldload pty' can be used to run old-style pseudo-terminals.
platforms.
This will make every attempt to mount a non-mpsafe filesystem to the
kernel forbidden, unless it is expressely compiled with
VFS_ALLOW_NONMPSAFE option.
This patch is part of the effort of killing non-MPSAFE filesystems
from the tree.
No MFC is expected for this patch.
long for specifying a boundary constraint.
- Change bus_dma tags to use bus_addr_t instead of bus_size_t for boundary
constraints.
These allow boundary constraints to be fully expressed for cases where
sizeof(bus_addr_t) != sizeof(bus_size_t). Specifically, it allows a
driver to properly specify a 4GB boundary in a PAE kernel.
Note that this cannot be safely MFC'd without a lot of compat shims due
to KBI changes, so I do not intend to merge it.
Reviewed by: scottl
