(Wasting 4k just as a temporary placeholder for a boot environment seems
a bit ridiculous, but hey.)
Tested: gxemul:
$ gxemul -e malta -d i:/home/adrian/work/freebsd/svn/mfsroot-rspro.img -C 4Kc /tftpboot/kernel.MALTA
* Add ah_ratesArray[] to the ar5416 HAL state - this stores the maximum
values permissable per rate.
* Since different chip EEPROM formats store this value in a different place,
store the HT40 power detector increment value in the ar5416 HAL state.
* Modify the target power setup code to store the maximum values in the
ar5416 HAL state rather than using a local variable.
* Add ar5416RateToRateTable() - to convert a hardware rate code to the
ratesArray enum / index.
* Add ar5416GetTxRatePower() - which goes through the gymnastics required
to correctly calculate the target TX power:
+ Add the power detector increment for ht40;
+ Take the power offset into account for AR9280 and later;
+ Offset the TX power correctly when doing open-loop TX power control;
+ Enforce the per-rate maximum value allowable.
Note - setting a TPC value of 0x0 in the TX descriptor on (at least)
the AR9160 resulted in the TX power being very high indeed. This didn't
happen on the AR9220. I'm guessing it's a chip bug that was fixed at
some point. So for now, just assume the AR5416/AR5418 and AR9130 are
also suspect and clamp the minimum value here at 1.
Tested:
* AR5416, AR9160, AR9220 hostap, verified using (2GHz) spectrum analyser
* Looked at target TX power in TX descriptor (using athalq) as well as TX
power on the spectrum analyser.
TODO:
* The TX descriptor code sets the target TX power to 0 for AR9285 chips.
I'm not yet sure why. Disable this for TPC and ensure that the TPC
TX power is set.
* AR9280, AR9285, AR9227, AR9287 testing!
* 5GHz testing!
Quirks:
* The per-packet TPC code is only exercised when the tpc sysctl is set
to 1. (dev.ath.X.tpc=1.) This needs to be done before you bring the
interface up.
* When TPC is enabled, setting the TX power doesn't end up with a call
through to the HAL to update the maximum TX power. So ensure that
you set the TPC sysctl before you bring the interface up and configure
a lower TX power or the hardware will be clamped by the lower TX
power (at least until the next channel change.)
Thanks to Qualcomm Atheros for all the hardware, and Sam Leffler for use
of his spectrum analyser to verify the TX channel power.
ath_tx_rate_fill_rcflags(). Include setting up the TX power cap in the
rate scenario setup code being passed to the HAL.
Other things:
* add a tx power cap field in ath_rc.
* Add a three-stream flag in ath_rc.
* Delete the LDPC flag from ath_rc - it's not a per-rate flag, it's a
global flag for the transmission.
The following change from illumos brought caused DTrace to
pause in an interactive environment:
3026 libdtrace should set LD_NOLAZYLOAD=1 to help the pid provider
This was not detected during testing because it doesn't
affect scripts.
We shouldn't be changing the environment, especially since the
LD_NOLAZYLOAD option doesn't apply to our (GNU) ld.
Unfortunately the change from upstream was made in such a way
that it is very difficult to separate this change from the
others so, at least for now, it's better to just revert
everything.
Reference:
https://www.illumos.org/issues/3026
Reported by: Navdeep Parhar and Mark Johnston
directly referencing ni->ni_txpower.
This provides the hardware with a slightly more accurate idea of
the maximum TX power to be using.
This is part of a series to get per-packet TPC to work (better).
Tested:
* AR5416, hostap mode
the given node.
This takes into account the per-node cap, the ic cap and the
per-channel regulatory caps.
This is designed to replace references to ni_txpower in various net80211
drivers - ni_txpower doesn't necessarily reflect the actual cap for
the given node (eg if the node has the default value of 50dBm (100) and
the administrator has manually configured a lower TX power.)
signal.
- Fix the old ksem implementation for POSIX semaphores to not restart
sem_wait() or sem_timedwait() if interrupted by a signal.
MFC after: 1 week
Pointy-hat to: me, for not realizing snprintf() is available in kernel.
Thanks to: jh, for bringing me the good news of snprintf(), Pawel Worach, for
noting that the panic can be provoked in i386 and not in amd64
Merge changes from illumos:
3675 DTrace print() should try to resolve function pointers
3676 dt_print_enum hardcodes a value of zero
Illumos Revision: b1fa6326238973aeaf12c34fcda75985b6c06be1
Reference:
https://www.illumos.org/issues/3675https://www.illumos.org/issues/3676
Obtained from: Illumos
MFC after: 1 month
The notes format is a header of sizeof(int), which stores the size of
the corresponding data structure to provide some versioning, and data
in the format as it is returned by a related sysctl call.
The userland tools (procstat(1)) will be taught to extract this data,
providing additional info for postmortem analysis.
PR: kern/173723
Suggested by: jhb
Discussed with: jhb, kib
Reviewed by: jhb (initial version), kib
MFC after: 1 month
Only look for FDT partitions if our potential parent is a DISK device.
Excluding direct recursion on the flashmap geoms was insufficient
because it did not prevent the underlying device from being retrieved if
flashmap geoms were further partitioned.
Reviewed by: imp
Sponsored by: DARPA, AFRL
and 64-bit MIPS. Don't use the floating-point coprocessor in the libstand
context for MIPS.
Reviewed by: imp
MFC after: 3 days
Sponsored by: DARPA, AFRL
LK_EXCLOTHER. LK_EXCLOTHER is only used to acquire a
usecount on a vnode during NFSv4 recovery from an
expired lease.
Reported and tested by: pho
MFC after: 2 weeks
for the set of IPv6 addresses. Now each attempt goes into IPv6 statistics,
even if given rule did not won. Change this and take into account only
those rules, that won. Also add accounting for cases, when algorithm
fails to select an address.
Merge change from illumos:
1731 DTrace NFS translators should be split into client/server pieces
Illumos Revision: 13523:6763769941d2
This code seems to be currently unused on FreeBSD.
Reference:
https://www.illumos.org/issues/1731
Obtained from: Illumos
MFC after: 1 week
PATH_MAX after the token substitution. This is wrong, because
origin_subst_one() performs the substitution on the whole rpath and
similar strings, which contain several pathes separated by colon. As
result, long (but correct) rpath consisting of many path elements is
rejected by the function.
Correct the problem by rewriting the origin_subst_one() to perform two
passes, first pass to calculate the number of substitutions to be
performed, and second pass to generate the resulting string. Second
pass allocates the memory for the result based on the count from the
first pass, without enforcing a limit.
Reported and tested by: pgj
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
to unique values.
There's some confusion about what the n32 assembler API really is
(since on page 9 of the spec they say that t0-t3 don't exist, then
turn around on page 22 and say that t4-t7 don't exist), and this
doesn't touch that.
NetBSD's version of this file follows the convention I used here, and
is likely to be correct.
This should fix gdb/ptrace.
is starting. This is in line with practice in OpenSolaris.
Note that this change is only in ULE and not in the 4BSD scheduler.
Once this change settles in (MFC timeout has expired) we'll try it out
on 4BSD as well.
PR: 177706
Submitted by: Tiwei Bie
MFC after: 1 month
