Because the TTY hooks interface was not finished when I imported the
MPSAFE TTY layer, I had to disconnect the snp(4) driver. This snp(4)
implementation has been sitting in my P4 branch for some time now.
Unfortunately it still doesn't use the same error handling as snp(4)
(returning codes through FIONREAD), but it should already be usable.
I'm committing this to SVN, hoping someone else could polish off its
rough edges. It's always better than having a broken driver sitting in
the tree.
that includes significant features and SMP safety.
This commit includes a more or less complete rewrite of the *BSD USB
stack, including Host Controller and Device Controller drivers and
updating all existing USB drivers to use the new USB API:
1) A brief feature list:
- A new and mutex enabled USB API.
- Many USB drivers are now running Giant free.
- Linux USB kernel compatibility layer.
- New UGEN backend and libusb library, finally solves the "driver
unloading" problem. The new BSD licensed libusb20 library is fully
compatible with libusb-0.1.12 from sourceforge.
- New "usbconfig" utility, for easy configuration of USB.
- Full support for Split transactions, which means you can use your
full speed USB audio device on a high speed USB HUB.
- Full support for HS ISOC transactions, which makes writing drivers
for various HS webcams possible, for example.
- Full support for USB on embedded platforms, mostly cache flushing
and buffer invalidating stuff.
- Safer parsing of USB descriptors.
- Autodetect of annoying USB install disks.
- Support for USB device side mode, also called USB gadget mode,
using the same API like the USB host side. In other words the new
USB stack is symmetric with regard to host and device side.
- Support for USB transfers like I/O vectors, means more throughput
and less interrupts.
- ... see the FreeBSD quarterly status reports under "USB project"
2) To enable the driver in the default kernel build:
2.a) Remove all existing USB device options from your kernel config
file.
2.b) Add the following USB device options to your kernel configuration
file:
# USB core support
device usb2_core
# USB controller support
device usb2_controller
device usb2_controller_ehci
device usb2_controller_ohci
device usb2_controller_uhci
# USB mass storage support
device usb2_storage
device usb2_storage_mass
# USB ethernet support, requires miibus
device usb2_ethernet
device usb2_ethernet_aue
device usb2_ethernet_axe
device usb2_ethernet_cdce
device usb2_ethernet_cue
device usb2_ethernet_kue
device usb2_ethernet_rue
device usb2_ethernet_dav
# USB wireless LAN support
device usb2_wlan
device usb2_wlan_rum
device usb2_wlan_ral
device usb2_wlan_zyd
# USB serial device support
device usb2_serial
device usb2_serial_ark
device usb2_serial_bsa
device usb2_serial_bser
device usb2_serial_chcom
device usb2_serial_cycom
device usb2_serial_foma
device usb2_serial_ftdi
device usb2_serial_gensa
device usb2_serial_ipaq
device usb2_serial_lpt
device usb2_serial_mct
device usb2_serial_modem
device usb2_serial_moscom
device usb2_serial_plcom
device usb2_serial_visor
device usb2_serial_vscom
# USB bluetooth support
device usb2_bluetooth
device usb2_bluetooth_ng
# USB input device support
device usb2_input
device usb2_input_hid
device usb2_input_kbd
device usb2_input_ms
# USB sound and MIDI device support
device usb2_sound
2) To enable the driver at runtime:
2.a) Unload all existing USB modules. If USB is compiled into the
kernel then you might have to build a new kernel.
2.b) Load the "usb2_xxx.ko" modules under /boot/kernel having the same
base name like the kernel device option.
Submitted by: Hans Petter Selasky hselasky at c2i dot net
Reviewed by: imp, alfred
and server. This replaces the RPC implementation of the NFS client and
server with the newer RPC implementation originally developed
(actually ported from the userland sunrpc code) to support the NFS
Lock Manager. I have tested this code extensively and I believe it is
stable and that performance is at least equal to the legacy RPC
implementation.
The NFS code currently contains support for both the new RPC
implementation and the older legacy implementation inherited from the
original NFS codebase. The default is to use the new implementation -
add the NFS_LEGACYRPC option to fall back to the old code. When I
merge this support back to RELENG_7, I will probably change this so
that users have to 'opt in' to get the new code.
To use RPCSEC_GSS on either client or server, you must build a kernel
which includes the KGSSAPI option and the crypto device. On the
userland side, you must build at least a new libc, mountd, mount_nfs
and gssd. You must install new versions of /etc/rc.d/gssd and
/etc/rc.d/nfsd and add 'gssd_enable=YES' to /etc/rc.conf.
As long as gssd is running, you should be able to mount an NFS
filesystem from a server that requires RPCSEC_GSS authentication. The
mount itself can happen without any kerberos credentials but all
access to the filesystem will be denied unless the accessing user has
a valid ticket file in the standard place (/tmp/krb5cc_<uid>). There
is currently no support for situations where the ticket file is in a
different place, such as when the user logged in via SSH and has
delegated credentials from that login. This restriction is also
present in Solaris and Linux. In theory, we could improve this in
future, possibly using Brooks Davis' implementation of variant
symlinks.
Supporting RPCSEC_GSS on a server is nearly as simple. You must create
service creds for the server in the form 'nfs/<fqdn>@<REALM>' and
install them in /etc/krb5.keytab. The standard heimdal utility ktutil
makes this fairly easy. After the service creds have been created, you
can add a '-sec=krb5' option to /etc/exports and restart both mountd
and nfsd.
The only other difference an administrator should notice is that nfsd
doesn't fork to create service threads any more. In normal operation,
there will be two nfsd processes, one in userland waiting for TCP
connections and one in the kernel handling requests. The latter
process will create as many kthreads as required - these should be
visible via 'top -H'. The code has some support for varying the number
of service threads according to load but initially at least, nfsd uses
a fixed number of threads according to the value supplied to its '-n'
option.
Sponsored by: Isilon Systems
MFC after: 1 month
compiled into the main AMR driver. It's code that is nice to have but not
required for normal operation, and it is reported to cause problems for some
people.
cable tuning. This has helped in some installations for hardware
deployed by a former employer. Made optional because the lists aren't
full of complaints about these cards... even when they were wildly
popular.
Reviewed by: attilio@, jhb@, trhodes@ (all an older version of the patch)
control logic and policy registration remaining in that file, and access
control checks broken out into other files by class of check.
Obtained from: TrustedBSD Project
Driver supports PCI devices with class 8 and subclass 5 according to
SD Host Controller Specification.
Update NOTES, enable module and static build.
Enable related mmc and mmcsd modules build.
Discussed on: mobile@, current@
This was located in the ubsa driver, but should be moved into a separate
driver:
- 3G modems provide multiple serial ports to allow AT commands while the PPP
connection is up.
- 3G modems do not provide baud rate or other serial port settings.
- Huawei cards need specific initialisation.
- ubsa is for Belkin adapters, an Linuxy choice for another device like 3G.
Speeds achieved here with a weak signal at best is ~40kb/s (UMTS). No spooky
STALLED messages as well.
Next: Move over all entries for Sierra and Novatel cards once I have found
testers, and implemented serial port enumeration for Sierra (or rather have
Andrea Guzzo do it). They list all endpoints in 1 iface instead of 4 ifaces.
Submitted by: aguzzo@anywi.com
MFC after: 3 weeks
If you just config KERNEL as usual there should be no apparent changes, you'll get all chipset support code compiled in.
However there is now a way to only compile in code for chipsets needed on a pr vendor basis. ATA now has the following "device" entries:
atacore: ATA core functionality, always needed for any ATA setup
atacard: CARDBUS support
atacbus: PC98 cbus support
ataisa: ISA bus support
atapci: PCI bus support only generic chipset support.
ataahci: AHCI support, also pulled in by some vendor modules.
ataacard, ataacerlabs, ataadaptec, ataamd, ataati, atacenatek, atacypress, atacyrix, atahighpoint, ataintel, ataite, atajmicron, atamarvell, atamicron, atanational, atanetcell, atanvidia, atapromise, ataserverworks, atasiliconimage, atasis, atavia; Vendor support, ie atavia for VIA chipsets
atadisk: ATA disk driver
ataraid: ATA softraid driver
atapicd: ATAPI cd/dvd driver
atapifd: ATAPI floppy/flashdisk driver
atapist: ATAPI tape driver
atausb: ATA<>USB bridge
atapicam: ATA<>CAM bridge
This makes it possible to config a kernel with just VIA chipset support by having the following ATA lines in the kernel config file:
device atacore
device atapci
device atavia
And then you need the atadisk, atapicd etc lines in there just as usual.
If you use ATA as modules loaded at boot there is few changes except the rename of the "ata" module to "atacore", things looks just as usual.
However under atapci you now have a whole bunch of vendor specific drivers, that you can kldload individually depending on you needs. Drivers have the same names as used in the kernel config explained above.
It seems we only depend on COMPAT_43 to implement the send() and recv()
routines. We can easily implement them using sendto() and recvfrom(),
just like we do inside our very own C library.
I wasn't able to really test it, apart from simple compilation testing.
I've heard rumours that COMPAT_SVR4 is broken inside execve() anyway.
It's still worth to fix this, because I suspect we'll get rid of
COMPAT_43 somewhere in the future...
Reviewed by: rdivacky
Discussed with: jhb
This is a sync to mesa/drm pre-gem, with a few fixes on top of that.
It also contains one local patch supplied by kib@ that I can't apply to
git.master shared code.
Approved by: flz
Obtained from: mesa/drm git.master
MFC after: 2 weeks
The last half year I've been working on a replacement TTY layer for the
FreeBSD kernel. The new TTY layer was designed to improve the following:
- Improved driver model:
The old TTY layer has a driver model that is not abstract enough to
make it friendly to use. A good example is the output path, where the
device drivers directly access the output buffers. This means that an
in-kernel PPP implementation must always convert network buffers into
TTY buffers.
If a PPP implementation would be built on top of the new TTY layer
(still needs a hooks layer, though), it would allow the PPP
implementation to directly hand the data to the TTY driver.
- Improved hotplugging:
With the old TTY layer, it isn't entirely safe to destroy TTY's from
the system. This implementation has a two-step destructing design,
where the driver first abandons the TTY. After all threads have left
the TTY, the TTY layer calls a routine in the driver, which can be
used to free resources (unit numbers, etc).
The pts(4) driver also implements this feature, which means
posix_openpt() will now return PTY's that are created on the fly.
- Improved performance:
One of the major improvements is the per-TTY mutex, which is expected
to improve scalability when compared to the old Giant locking.
Another change is the unbuffered copying to userspace, which is both
used on TTY device nodes and PTY masters.
Upgrading should be quite straightforward. Unlike previous versions,
existing kernel configuration files do not need to be changed, except
when they reference device drivers that are listed in UPDATING.
Obtained from: //depot/projects/mpsafetty/...
Approved by: philip (ex-mentor)
Discussed: on the lists, at BSDCan, at the DevSummit
Sponsored by: Snow B.V., the Netherlands
dcons(4) fixed by: kan
This driver supports GW3887 based chipsets and works on
x86/powerpc/sparc64. You need upgtfw kernel module before loading
upgt(4). Please see the manpage.
Obtained from: OpenBSD
found in Soekris hardware, for instance). The hardware supports acceleration
of AES-128-CBC accessible through crypto(4) and supplies entropy to random(4).
TODO:
o Implement rndtest(4) support
o Performance enhancements
Submitted by: Patrick Lamaizière <patfbsd -at- davenulle.org>
Reviewed by: jhb, sam
MFC after: 1 week
features of CPUs like reading/writing machine-specific registers,
retrieving cpuid data, and updating microcode.
- Add cpucontrol(8) utility, that provides userland access to
the features of cpuctl(4).
- Add subsequent manpages.
The cpuctl(4) device operates as follows. The pseudo-device node cpuctlX
is created for each cpu present in the systems. The pseudo-device minor
number corresponds to the cpu number in the system. The cpuctl(4) pseudo-
device allows a number of ioctl to be preformed, namely RDMSR/WRMSR/CPUID
and UPDATE. The first pair alows the caller to read/write machine-specific
registers from the correspondent CPU. cpuid data could be retrieved using
the CPUID call, and microcode updates are applied via UPDATE.
The permissions are inforced based on the pseudo-device file permissions.
RDMSR/CPUID will be allowed when the caller has read access to the device
node, while WRMSR/UPDATE will be granted only when the node is opened
for writing. There're also a number of priv(9) checks.
The cpucontrol(8) utility is intened to provide userland access to
the cpuctl(4) device features. The utility also allows one to apply
cpu microcode updates.
Currently only Intel and AMD cpus are supported and were tested.
Approved by: kib
Reviewed by: rpaulo, cokane, Peter Jeremy
MFC after: 1 month
As clearly mentioned on the mailing lists, there is a list of drivers
that have not been ported to the MPSAFE TTY layer yet. Remove them from
the kernel configuration files. This means people can now still use
these drivers if they explicitly put them in their kernel configuration
file, which is good.
People should keep in mind that after August 10, these drivers will not
work anymore. Even though owners of the hardware are capable of getting
these drivers working again, I will see if I can at least get them to a
compilable state (if time permits).
MPSAFE patches on current@ and stable@. This driver also has a fundamental
issue in that it sleeps when sending commands to the card including in the
if_init/if_start routines (which can be called from interrupt context). As
such, the driver shouldn't be working reliably even on 4.x.
and stable@. It also is a driver for an older non-802.11 wireless PC card
that is quite slow in comparison to say, wi(4). I know Warner wants this
driver axed as well.
current@ and stable@ for the locking patches. The driver can always be
revived if someone tests it.
This driver also sleeps in its if_init routine, so it likely doesn't really
work at all anyway in modern releases.
semaphores. Specifically, semaphores are now represented as new file
descriptor type that is set to close on exec. This removes the need for
all of the manual process reference counting (and fork, exec, and exit
event handlers) as the normal file descriptor operations handle all of
that for us nicely. It is also suggested as one possible implementation
in the spec and at least one other OS (OS X) uses this approach.
Some bugs that were fixed as a result include:
- References to a named semaphore whose name is removed still work after
the sem_unlink() operation. Prior to this patch, if a semaphore's name
was removed, valid handles from sem_open() would get EINVAL errors from
sem_getvalue(), sem_post(), etc. This fixes that.
- Unnamed semaphores created with sem_init() were not cleaned up when a
process exited or exec'd. They were only cleaned up if the process
did an explicit sem_destroy(). This could result in a leak of semaphore
objects that could never be cleaned up.
- On the other hand, if another process guessed the id (kernel pointer to
'struct ksem' of an unnamed semaphore (created via sem_init)) and had
write access to the semaphore based on UID/GID checks, then that other
process could manipulate the semaphore via sem_destroy(), sem_post(),
sem_wait(), etc.
- As part of the permission check (UID/GID), the umask of the proces
creating the semaphore was not honored. Thus if your umask denied group
read/write access but the explicit mode in the sem_init() call allowed
it, the semaphore would be readable/writable by other users in the
same group, for example. This includes access via the previous bug.
- If the module refused to unload because there were active semaphores,
then it might have deregistered one or more of the semaphore system
calls before it noticed that there was a problem. I'm not sure if
this actually happened as the order that modules are discovered by the
kernel linker depends on how the actual .ko file is linked. One can
make the order deterministic by using a single module with a mod_event
handler that explicitly registers syscalls (and deregisters during
unload after any checks). This also fixes a race where even if the
sem_module unloaded first it would have destroyed locks that the
syscalls might be trying to access if they are still executing when
they are unloaded.
XXX: By the way, deregistering system calls doesn't do any blocking
to drain any threads from the calls.
- Some minor fixes to errno values on error. For example, sem_init()
isn't documented to return ENFILE or EMFILE if we run out of semaphores
the way that sem_open() can. Instead, it should return ENOSPC in that
case.
Other changes:
- Kernel semaphores now use a hash table to manage the namespace of
named semaphores nearly in a similar fashion to the POSIX shared memory
object file descriptors. Kernel semaphores can now also have names
longer than 14 chars (up to MAXPATHLEN) and can include subdirectories
in their pathname.
- The UID/GID permission checks for access to a named semaphore are now
done via vaccess() rather than a home-rolled set of checks.
- Now that kernel semaphores have an associated file object, the various
MAC checks for POSIX semaphores accept both a file credential and an
active credential. There is also a new posixsem_check_stat() since it
is possible to fstat() a semaphore file descriptor.
- A small set of regression tests (using the ksem API directly) is present
in src/tools/regression/posixsem.
Reported by: kris (1)
Tested by: kris
Reviewed by: rwatson (lightly)
MFC after: 1 month
provides the correct semantics for flock(2) style locks which are used by the
lockf(1) command line tool and the pidfile(3) library. It also implements
recovery from server restarts and ensures that dirty cache blocks are written
to the server before obtaining locks (allowing multiple clients to use file
locking to safely share data).
Sponsored by: Isilon Systems
PR: 94256
MFC after: 2 weeks
NET_NEEDS_GIANT. netatm has been disconnected from the build for ten
months in HEAD/RELENG_7. Specifics:
- netatm include files
- netatm command line management tools
- libatm
- ATM parts in rescue and sysinstall
- sample configuration files and documents
- kernel support as a module or in NOTES
- netgraph wrapper nodes for netatm
- ctags data for netatm.
- netatm-specific device drivers.
MFC after: 3 weeks
Reviewed by: bz
Discussed with: bms, bz, harti
-It has new hardware support
-It uses a new method of TX cleanup called Head Write Back
-It includes the provisional generic TCP LRO feature contributed
by Myricom and made general purpose by me. This should move into
the stack upon approval but for this driver drop its in here.
-Also bug fixes and etc...
MFC in a week if no serious issues arise.
perform various operations on a controller. Specifically, for each mpt(4)
device, create a character device in devfs which accepts ioctl requests for
reading and writing configuration pages and performing RAID actions.
MFC after: 1 week
Reviewed by: scottl
which are also likely to be irrelevant for sun4v (there's no SBus on sun4v
and only some EBus devices). While at it fix some style bugs according to
style.Makefile(5) where appropriate.
MFC after: 3 days
PR 122839 is fixed in both em and in igb
Second, the issue on building modules since the static kernel
build changes is now resolved. I was not able to get the fancier
directory hierarchy working, but this works, both em and igb
build as modules now.
Third, there is now support in em for two new NICs, Hartwell
(or 82574) is a low cost PCIE dual port adapter that has MSIX,
for this release it uses 3 vectors only, RX, TX, and LINK. In
the next release I will add a second TX and RX queue. Also, there
is support here for ICH10, the followon to ICH9. Both of these are
early releases, general availability will follow soon.
Fourth: On Hartwell and ICH10 we now have IEEE 1588 PTP support,
I have implemented this in a provisional way so that early adopters
may try and comment on the functionality. The IOCTL structure may
change. This feature is off by default, you need to edit the Makefile
and add the EM_TIMESYNC define to get the code.
Enjoy all!!
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)
move most offload functionality from NIC to TOE
factor out all socket and inpcb direct access
factor out access to locking in incpb, pcbinfo, and sockbuf
and the igb driver static in the kernel. But it also reflects
some other bug fixes in my development stream at Intel.
PR 122373 is also fixed in this code.
src/cddl and src/sys/cddl directories per the core@ decision following
the license review.
This change modifies the affected Makefiles to reference the sources
in their new location.
to detect (or load) kernel NLM support in rpc.lockd. Remove the '-k'
option to rpc.lockd and make kernel NLM the default. A user can still
force the use of the old user NLM by building a kernel without NFSLOCKD
and/or removing the nfslockd.ko module.
just em, there is an igb driver (this follows behavior with our Linux drivers).
All adapters up to the 82575 are supported in em, and new client/desktop support
will continue to be in that adapter.
The igb driver is for new server NICs like the 82575 and its followons.
Advanced features for virtualization and performance will be in this driver.
Also, both drivers now have shared code that is up to the latest we have
released. Some stylistic changes as well.
Enjoy :)
- add support for T3C
- add DDP support (zero-copy receive)
- fix TOE transmit of large requests
- fix shutdown so that sockets don't remain in CLOSING state indefinitely
- register listeners when an interface is brought up after tom is loaded
- fix setting of multicast filter
- enable link at device attach
- exit tick handler if shutdown is in progress
- add helper for logging TCB
- add sysctls for dumping transmit queues
- note that TOE wxill not be MFC'd until after 7.0 has been finalized
MFC after: 3 days
VFS namecache, as is done by the Coda module on Linux. Unlike the Coda
namecache, the global VFS namecache isn't tagged by credential, so use
ore conservative flushing behavior (for now) when CODA_PURGEUSER is
issued by Venus.
This improves overall integration with the FreeBSD VFS, including
allowing __getcwd() to work better, procfs/procstat monitoring, and so
on. This improves shell behavior in many cases, and improves ".."
handling. It may lead to some slowdown until we've implemented a
specific access cache, which should net improve performance, but in the
mean time, lookup access control now always goes to Venus, whereas
previously it didn't.
MFC after: 1 month
DP83847 PHYs. The main reason for using a specific driver for these
PHYs are reset quirks similar to the nsphy(4) driven DP83840A.
PR: 112654
Obtained from: NetBSD
MFC after: 2 weeks
Thanks to: mlaier for testing w/ DP83815
queues (which we call slices). The NIC will steer traffic into up to
hw.mxge.max_slices different receive rings based on a configurable
hash type (hw.mxge.rss_hash_type).
Currently the driver defaults to using a single slice, so the default
behavior is unchanged. Also, transmit from non-zero slices is
disabled currently.
and t3_push_frames).
- Import latest changes to cxgb_main.c and cxgb_sge.c from toestack p4 branch
- make driver local copy of tcp_subr.c and tcp_usrreq.c and override tcp_usrreqs so
TOE can also functions on versions with unmodified TCP
- add cxgb back to the build
cards:
o RocketRAID 172x series
o RocketRAID 174x series
o RocketRAID 2210
o RocketRAID 222x series
o RocketRAID 2240
o RocketRAID 230x series
o RocketRAID 231x series
o RocketRAID 232x series
o RocketRAID 2340
o RocketRAID 2522
Many thanks to Highpoint for their continued support of FreeBSD.
Submitted by: Highpoint
bumped to 800004 to note the change though userland apps should not be
affected since they use <sys/agpio.h> rather than the headers in
sys/dev/agp.
Discussed with: anholt
Repocopy by: simon
This includes:
o mtree (for legal/intel_wpi)
o manpage for i386/amd64 archs
o module for i386/amd64 archs
o NOTES for i386/amd64 archs
Approved by: mlaier (comentor)
This import includes:
o wpi Wireless driver for the Intel 3945 Wireless Lan Controller (802.11abg) (sys/dev/wpi)
o Intel firmware revision 2.14.4 & associated LICENSE (sys/dev/contrib/wpi, sys/contrib/dev/wpi/LICENSE)
o wpifw Firmware driver (sys/modules/wpifw)
Approved by: mlaier, sam (co-mentors)
changes:
01 - Enhanced LRO:
LRO feature is extended to support multi-buffer mode. Previously,
Ethernet frames received in contiguous buffers were offloaded.
Now, frames received in multiple non-contiguous buffers can be
offloaded, as well. The driver now supports LRO for jumbo frames.
02 - Locks Optimization:
The driver code was re-organized to limit the use of locks.
Moreover, lock contention was reduced by replacing wait locks
with try locks.
03 - Code Optimization:
The driver code was re-factored to eliminate some memcpy
operations. Fast path loops were optimized.
04 - Tag Creations:
Physical Buffer Tags are now optimized based upon frame size.
For better performance, Physical Memory Maps are now re-used.
05 - Configuration:
Features such as TSO, LRO, and Interrupt Mode can be configured
either at load or at run time. Rx buffer mode (mode 1 or mode 2)
can be configured at load time through kenv.
06 - Driver Statistics:
Run time statistics are enhanced to provide better visibility
into the driver performance.
07 - Bug Fixes:
The driver contains fixes for the problems discovered and
reported since last submission.
08 - MSI support:
Added Message Signaled Interrupt feature which currently uses 1
message.
09 Removed feature:
Rx 3 buffer mode feature has been removed. Driver now supports 1,
2 and 5 buffer modes of which 2 and 5 buffer modes can be used
for header separation.
10 Compiler warning:
Fixed compiler warning when compiled for 32 bit system.
11 Copyright notice:
Source files are updated with the proper copyright notice.
MFC after: 3 days
Submitted by: Alicia Pena <Alicia dot Pena at neterion dot com>,
Muhammad Shafiq <Muhammad dot Shafiq at neterion dot com>
refactored it to be a generic device.
Instead of being part of the standard kernel, there is now a 'nvram' device
for i386/amd64. It is in DEFAULTS like io and mem, and can be turned off
with 'nodevice nvram'. This matches the previous behavior when it was
first committed.
to gem_attach() as the former access softc members not yet initialized
at that time and gem_reset() actually is enough to stop the chip. [1]
o Revise the use of gem_bitwait(); add bus_barrier() calls before calling
gem_bitwait() to ensure the respective bit has been written before we
starting polling on it and poll for the right bits to change, f.e. even
though we only reset RX we have to actually wait for both GEM_RESET_RX
and GEM_RESET_TX to clear. Add some additional gem_bitwait() calls in
places we've been missing them according to the GEM documentation.
Along with this some excessive DELAYs, which probably only were added
because of bugs in gem_bitwait() and its use in the first place, as
well as as have of an gem_bitwait() reimplementation in gem_reset_tx()
were removed.
o Add gem_reset_rxdma() and use it to deal with GEM_MAC_RX_OVERFLOW errors
more gracefully as unlike gem_init_locked() it resets the RX DMA engine
only, causing no link loss and the FIFOs not to be cleared. Also use it
deal with GEM_INTR_RX_TAG_ERR errors, with previously were unhandled.
This was based on information obtained from the Linux GEM and OpenSolaris
ERI drivers.
o Turn on workarounds for silicon bugs in the Apple GMAC variants.
This was based on information obtained from the Darwin GMAC and Linux GEM
drivers.
o Turn on "infinite" (i.e. maximum 31 * 64 bytes in length) DMA bursts.
This greatly improves especially RX performance.
o Optimize the RX path, this consists of:
- kicking the receiver as soon as we've a spare descriptor in gem_rint()
again instead of just once after all the ready ones have been handled;
- kicking the receiver the right way, i.e. as outlined in the GEM
documentation in batches of 4 and by pointing it to the descriptor
after the last valid one;
- calling gem_rint() before gem_tint() in gem_intr() as gem_tint() may
take quite a while;
- doubling the size of the RX ring to 256 descriptors.
Overall the RX performance of a GEM in a 1GHz Sun Fire V210 was improved
from ~100Mbit/s to ~850Mbit/s.
o In gem_add_rxbuf() don't assign the newly allocated mbuf to rxs_mbuf
before calling bus_dmamap_load_mbuf_sg(), if bus_dmamap_load_mbuf_sg()
fails we'll free the newly allocated mbuf, unable to recycle the
previous one but a NULL pointer dereference instead.
o In gem_init_locked() honor the return value of gem_meminit().
o Simplify gem_ringsize() and dont' return garbage in the default case.
Based on OpenBSD.
o Don't turn on MAC control, MIF and PCS interrupts unless GEM_DEBUG is
defined as we don't need/use these interrupts for operation.
o In gem_start_locked() sync the DMA maps of the descriptor rings before
every kick of the transmitter and not just once after enqueuing all
packets as the NIC might instantly start transmitting after we kicked
it the first time.
o Keep state of the link state and use it to enable or disable the MAC
in gem_mii_statchg() accordingly as well as to return early from
gem_start_locked() in case the link is down. [3]
o Initialize the maximum frame size to a sane value.
o In gem_mii_statchg() enable carrier extension if appropriate.
o Increment if_ierrors in case of an GEM_MAC_RX_OVERFLOW error and in
gem_eint(). [3]
o Handle IFF_ALLMULTI correctly; don't set it if we've turned promiscuous
group mode on and don't clear the flag if we've disabled promiscuous
group mode (these were mostly NOPs though). [2]
o Let gem_eint() also report GEM_INTR_PERR errors.
o Move setting sc_variant from gem_pci_probe() to gem_pci_attach() as
device probe methods are not supposed to touch the softc.
o Collapse sc_inited and sc_pci into bits for sc_flags.
o Add CTASSERTs ensuring that GEM_NRXDESC and GEM_NTXDESC are set to
legal values.
o Correctly set up for 802.3x flow control, though #ifdef out the code
that actually enables it as this needs more testing and mainly a proper
framework to support it.
o Correct and add some conversions from hard-coded functions names to
__func__ which were borked or forgotten in if_gem.c rev. 1.42.
o Use PCIR_BAR instead of a homegrown macro.
o Replace sc_enaddr[6] with sc_enaddr[ETHER_ADDR_LEN].
o In gem_pci_attach() in case attaching fails release the resources in
the opposite order they were allocated.
o Make gem_reset() static to if_gem.c as it's not needed outside that
module.
o Remove the GEM_GIGABIT flag and the associated code; GEM_GIGABIT was
never set and the associated code was in the wrong place.
o Remove sc_mif_config; it was only used to cache the contents of the
respective register within gem_attach().
o Remove the #ifdef'ed out NetBSD/OpenBSD code for establishing a suspend
hook as it will never be used on FreeBSD.
o Also probe Apple Intrepid 2 GMAC and Apple Shasta GMAC, add support for
Apple K2 GMAC. Based on OpenBSD.
o Add support for Sun GBE/P cards, or in other words actually add support
for cards based on GEM to gem(4). This mainly consists of adding support
for the TBI of these chips. Along with this the PHY selection code was
rewritten to hardcode the PHY number for certain configurations as for
example the PHY of the on-board ERI of Blade 1000 shows up twice causing
no link as the second incarnation is isolated.
These changes were ported from OpenBSD with some additional improvements
and modulo some bugs.
o Add code to if_gem_pci.c allowing to read the MAC-address from the VPD on
systems without Open Firmware.
This is an improved version of my variant of the respective code in
if_hme_pci.c
o Now that gem(4) is MI enable it for all archs.
Pointed out by: yongari [1]
Suggested by: rwatson [2], yongari [3]
Tested on: i386 (GEM), powerpc (GMACs by marcel and yongari),
sparc64 (ERI and GEM)
Reviewed by: yongari
Approved by: re (kensmith)
polling/interrupt-driven fallback and instead use polling only during
boot and pure interrupt-driven mode after boot. Polled mode could be
relegated completely to a legacy role if we could enable interrupts
during boot. Polled mode can be forced after boot by setting
debug.acpi.ec.polled="1", i.e. if there are timeouts.
- Use polling only during boot, shutdown, or if requested by the user.
Otherwise, use a generation count of GPEs, incremented atomically. This
prevents an old status value from being used if the EC is really slow
and the same condition (i.e. multiple IBEs for a write transaction) is
being checked.
- Check for and run the query handler directly if the SCI bit is set in
the status register during boot. Previously, the query handler wouldn't
run until interrupts were finally enabled late in boot.
- During boot and after starting a command, check if the event appears
to already have occurred before we even start waiting. If so, it's
possible the EC is very slow and we might accept an old status value.
Print a warning in this case. Once we've booted, interrupt-driven mode
should work just fine but polled mode could be unreliable. There's not
much more we can do about this until interrupts are enabled during boot.
- In the above case, we also do one final check if the interrupt-driven
mode gets a timeout. If the status is complete, it will force the
system back into polled mode since interrupt mode doesn't work. For
polled mode during boot, if the status appears to be already complete
before beginning the check loop, it waits 10 us before actually checking
the status, just in case the EC is really slow and hasn't gotten to work
on the new request yet.
- Use upper-case hex for the _Qxx method
- Use device_printf for errors, don't hide them under verbose
- Increase default total timeout to 750 ms and decrease polling interval
to 5 us.
- Don't pass the status value via the softc. Just read it directly.
- Remove the mutex. We use the sx lock for transaction serialization
with the query handler.
- Remove the Intel copyright notice as no code of theirs was ever
present in this file (verified against rev 1.1)
- Allow KTR module-only builds for ease of testing
Thanks to jkim and Alexey Starikovskiy for helpful discussions and testing.
Approved by: re
MFC after: 2 weeks
providers with limited physical storage and add physical storage as
needed.
Submitted by: Ivan Voras
Sponsored by: Google Summer of Code 2006
Approved by: re (kensmith)
other changes too).
(without any real order)
1. Use device_get_nameunit for mutex naming
2. Add timer for low-latency playback
3. Move most mixer controls from sysctls to mixer(8) controls.
This is a largest part of this patch.
4. Add analog/digital switch (as a temporary sysctl)
5. Get back support for low-bitrate playback (with help of (2))
6. Change locking for exclusive I/O. Writing to non-PTR register
is almost safe and does not need to be ordered with PTR operations.
7. Disable MIDI until we get it to detach properly and fix memory
managment problems.
8. Enable multichannel playback by default. It is as stable as
single-channel mode. Multichannel recording is still an
experimental feature.
9. Multichannel options can be changed by loader tunables.
10. Add a way to disable card from a loader tunable.
11. Add new PCI IDs.
12. Debugger settings are loader tunables now.
14. Remove some unused variables.
15. Mark pcm sub-devices MPSAFE.
16. Partially revert (bus_setup_intr -> snd_setup_intr) since it need
to be done independently
Submitted by: Yuriy Tsibizov (driver maintainer)
Approved by: re (bmah)
- fix the use after free seen when sending packets small enough to fit as an immediate
and bpf peers are present
- update to firmware rev 4.7 along with various small vendor fixes
Supported by: Chelsio
Approved by: re (blanket)
MFC after: 3 days
The first drop was Beta, this code is expected to be the release version.
Note that this driver code will build in either 6.2 or 7. If you
use the code in 6.2 you will not get TSO or MSI/X support but it will
function in a legacy mode.
Approved by: re
and newer CPUs (including Core 2 and Core / Core 2 based Xeons). The
driver attaches to each cpu device and creates a sysctl node in that
device's sysctl context (dev.cpu.N.temperature). When invoked, the
handler binds to the appropriate CPU to ensure a correct reading.
Submitted by: Rui Paulo <rpaulo@fnop.net>
Sponsored by: Google Summer of Code 2007
Tested by: des, marcus, Constantine A. Murenin, Ian FREISLICH
Approved by: re (kensmith)
MFC after: 3 weeks
included man pages on how to use it. This code is still somewhat experimental
but has been successfully tested on a number of targets. Many thanks to
Danny for contributing this.
Approved by: re
- Add custom .c wrappers for the firmware, rather than the standard
firmware(9) generated firmware objects to work around toolchain
problems on ia64 involving linking objects produced by
ld -b -binary into the kernel.
- Move from using Myricom's ".dat" firmware blobs to using Myricom's
zlib compressed ".h" firmware header files. This is done to
facilitate the custom wrappers, and saves a fair amount of wired
memory in the case where the firmware is built in, or preloaded.
- Fix two compile issues in mxge which only appear on non-i386/amd64.
Reviewed by: mlaier, mav (earlier version with just zlib support)
Glanced at by: sam
Approved by: re (kensmith)
NET_NEEDS_GIANT, which will shortly be removed. This is done in a
away that it may be easily reattached to the build before 7.1 if
appropriate locking is added. Specifics:
- Don't install netatm include files
- Disconnect netatm command line management tools
- Don't build libatm
- Don't include ATM parts in rescue or sysinstall
- Don't install sample configuration files and documents
- Don't build kernel support as a module or in NOTES
- Don't build netgraph wrapper nodes for netatm
This removes the last remaining consumer of NET_NEEDS_GIANT.
Reviewed by: harti
Discussed with: bz, bms
Approved by: re (kensmith)
by removing files from src/sys/coda, and updating include paths in the
new location, kernel configuration, and Makefiles. In one case add
$FreeBSD$.
Discussed with: anderson, Jan Harkes <jaharkes@cs.cmu.edu>
Approved by: re (kensmith)
Repo-copy madness: simon
- Remove unnecessary NULL checks after M_WAITOK allocations.
- Use VOP_ACCESS instead of hand-rolled suser_cred()
calls. [1]
- Use malloc(9) KPI to allocate memory for string. The
optimization taken from NetBSD is not valid for FreeBSD
because our malloc(9) already act that way. [2]
Requested by: rwatson [1]
Submitted by: Howard Su [2]
Approved by: re (tmpfs blanket)
around to force the IO port to a fixed address. They were only turned
on in the module build and were present since the original import. This
breaks soft power-off on the Asus A7V since it reprograms the SMBus base
address to a different one than the BIOS expects. A similar issue was
found in the alpm(4) module build.
PR: kern/113986, i386/97468
MFC after: 3 days
Approved by: re
when 'make obj' was done first. I found this when fixing
a problem reported by tinderbox, but forgot to send the
patchset to re@ altogether.
Approved by: re (kensmith)
Please note that, this is currently considered as an
experimental feature so there could be some rough
edges. Consult http://wiki.freebsd.org/TMPFS for
more information.
For now, connect tmpfs to build on i386 and amd64
architectures only. Please let us know if you have
success with other platforms.
This work was developed by Julio M. Merino Vidal
for NetBSD as a SoC project; Rohit Jalan ported it
from NetBSD to FreeBSD. Howard Su and Glen Leeder
are worked on it to continue this effort.
Obtained from: NetBSD via p4
Submitted by: Howard Su (with some minor changes)
Approved by: re (kensmith)
- update to firmware version 4.1.0
- switch over to standard method for initializing cdevs (contributed by scottl@)
- break out timer_reclaim_task to be per-port
- move msix teardown into separate function
- fix bus_setup_intr for msi-x for the multi-port case so that msi-x resources
are not corrupted on unload
- handle 10/100/1000 base-T media and auto negotiation
- bind qset to cpu even for singleq case
- white space cleanups
- remove recursive PORT_LOCK
- move mtu setting to separate function
- stop and re-init port when changing mtu
- replace all direct references to m_data with calls to mtod
- handle attach failure better by not trying to de-initialize
taskqueues when they have not been allocated
- no longer default to jumbo frames
Sponsored by: Chelsio
MFC after: 3 days
- Add and document the KVM and KVM_SUPPORT options that
are needed for the ifmcstats(3) makefile
- Garbage collect unused variables
- Add missing inclusion of bsd.own.mk where needed
Approved by: kan (mentor)
Reviewed by: ru
o major overhaul of the way channels are handled: channels are now
fully enumerated and uniquely identify the operating characteristics;
these changes are visible to user applications which require changes
o make scanning support independent of the state machine to enable
background scanning and roaming
o move scanning support into loadable modules based on the operating
mode to enable different policies and reduce the memory footprint
on systems w/ constrained resources
o add background scanning in station mode (no support for adhoc/ibss
mode yet)
o significantly speedup sta mode scanning with a variety of techniques
o add roaming support when background scanning is supported; for now
we use a simple algorithm to trigger a roam: we threshold the rssi
and tx rate, if either drops too low we try to roam to a new ap
o add tx fragmentation support
o add first cut at 802.11n support: this code works with forthcoming
drivers but is incomplete; it's included now to establish a baseline
for other drivers to be developed and for user applications
o adjust max_linkhdr et. al. to reflect 802.11 requirements; this eliminates
prepending mbufs for traffic generated locally
o add support for Atheros protocol extensions; mainly the fast frames
encapsulation (note this can be used with any card that can tx+rx
large frames correctly)
o add sta support for ap's that beacon both WPA1+2 support
o change all data types from bsd-style to posix-style
o propagate noise floor data from drivers to net80211 and on to user apps
o correct various issues in the sta mode state machine related to handling
authentication and association failures
o enable the addition of sta mode power save support for drivers that need
net80211 support (not in this commit)
o remove old WI compatibility ioctls (wicontrol is officially dead)
o change the data structures returned for get sta info and get scan
results so future additions will not break user apps
o fixed tx rate is now maintained internally as an ieee rate and not an
index into the rate set; this needs to be extended to deal with
multi-mode operation
o add extended channel specifications to radiotap to enable 11n sniffing
Drivers:
o ath: add support for bg scanning, tx fragmentation, fast frames,
dynamic turbo (lightly tested), 11n (sniffing only and needs
new hal)
o awi: compile tested only
o ndis: lightly tested
o ipw: lightly tested
o iwi: add support for bg scanning (well tested but may have some
rough edges)
o ral, ural, rum: add suppoort for bg scanning, calibrate rssi data
o wi: lightly tested
This work is based on contributions by Atheros, kmacy, sephe, thompsa,
mlaier, kevlo, and others. Much of the scanning work was supported by
Atheros. The 11n work was supported by Marvell.
builds had been succeeding if run serially but could fail if run in
parallel because the bge module build might start before ofw_bus_if.h
got created as part of the mainline kernel build.
Diagnosis and patch by: ru
implementing some of them using existing ones.
- Allow to compile ZFS on all archs and use atomic operations surrounded
by global mutex on archs we don't have or can't have all atomic
operations needed by ZFS.
- Rework the entire pcm_channel structure:
* Remove rarely used link placeholder, instead, make each pcm_channel
as head/link of each own/each other. Unlock - Lock sequence due to
sleep malloc has been reduced.
* Implement "busy" queue which will contain list of busy/active
channels. This greatly reduce locking contention for example while
servicing interrupt for hardware with many channels or when virtual
channels reach its 256 peak channels.
- So I heard you like v chan ... O RLY?
Welcome to Virtual **Record** Channels (vrec, rec vchans, vchans for
recording, Rec-Chan, you decide), the ultimate solutions for your
nagging O_RDWR full-duplex wannabe (note: flash plugins) monopolizing
single record channel causing EBUSY. Vrec works exactly like Vchans
(or, should I rename it to "Vplay" :) , except that it operates on the
opposite direction (recording). Up to 256 vrecs (like vchans) are
possible.
Notes:
* Relocate dev.pcm.%d.{vchans,vchanformat,vchanrate} to each of its
respective node/direction:
dev.pcm.%d.play.* for "play" (cdev = dsp%d.vp%d)
dev.pcm.%d.rec.* for "record" (cdev = dsp%d.vr%d)
* Don't expect that it will magically give you ability to split
"recording source" (eg: 1 channel for cdrom, 1 channel for mic,
etc). Just admit that you only have a *single* recording source /
channel. Please bug your hardware vendor instead :)
- Bump maxautovchans from 4 to 16. For a full-fledged multimedia
desktop/workstation with too many soundservers installed (esound,
artsd, jackd, pulse/polypaudio, ding-dong pling plong mudkip fuh fuh,
etc), 4 seems inadequate. There will be no memory penalty here, since
virtual channels are allocate only by demand.
- Nuke/Rework the entire statically created cdev entries. Everything is
clonable through snd own clone manager which designed to withstand many
kind of abusive devfs droids such as:
* while : ; do /bin/test -e /dev/dsp ; done
* jot 16777216 0 | while read x ; do ls /dev/dsp0.$x ; done
* hundreds (could be thousands) concurrent threads/process opening
"/dev/dsp" (previously, this might result EBUSY even with just
3 contesting threads/procs).
o Reusable clone objects (instead of creating new one like there's no
tomorrow) after certain expiration deadline. The clone allocator will
decide whether to reuse, share, or creating new clone.
o Automatic garbage collector.
- Dynamic unit magic allocator. Maximum attached soundcards can be tuned
using tunable "hw.snd.maxunit" (Default to 512). Minimum is 16, and
maximum is 2048.
- ..other fixes, mostly related to concurrency issues.
joel@ will do the manpage updates on sound(4).
Have fun.
- upgrade to reflect state of 1.0.0.86
- move from firmware rev 3.2 to 4.0.0
- import driver bits for offload functionality
- remove binary distribution clause from top level files as it
runs counter to the intent of purely supporting the hardware
MFC after: 3 days
Implement all futex atomic operations in assembler to not depend on the
fuword() that does not allow to distinguish between -1 and failure return.
Correctly return 0 from atomic operations on success.
In collaboration with: rdivacky
Tested by: Scot Hetzel <swhetzel gmail com>, Milos Vyletel <mvyletel mzm cz>
Sponsored by: Google SoC 2007
This patch does the following:
- Remove un-necessary code that is not even compiling into the driver
under TW_OSL_NON_DMA_MEM_ALLOC_PER_REQUEST defines.
- Remove bundled firmware image and associated "files" entry for tw_cl_fwimg.c
- Remove bundled firmware flashing routines. We now have tw_update userspace
FreeBSD controller flash utility.
- Fix driver crash on load due to shared interrupt.
- Fix 2 lock leaks for Giant lock.
- Fix CCB leak.
- Add support for 9650SE controllers.
Many thanks to 3Ware/AMCC for continuing to support FreeBSD.
shared code infrastructure that is family specific and
modular. There is also support for our latest gigabit
nic, the 82575 that is MSI/X and multiqueue capable.
The new shared code changes some interfaces to the core
code but testing at Intel has been going on for months,
it is fairly stable.
I have attempted to be careful in retaining any fixes that
CURRENT had and we did not, I apologize in advance if any
thing gets clobbered, I'm sure I'll hear about it :)
Approved by pdeuskar
The name trunk is misused as the networking term trunk means carrying multiple
VLANs over a single connection. The IEEE standard for link aggregation (802.3
section 3) does not talk about 'trunk' at all while it is used throughout IEEE
802.1Q in describing vlans.
The lagg(4) driver provides link aggregation, failover and fault tolerance.
Discussed on: current@
front-end if the dpt(4) module is built along with a kernel that
includes eisa(4) or when compiling it stand-alone (logic based on
the corresponding ISA logic in sys/modules/sound/sound/Makefile).
As as side-effect this fixes the stand-alone build of the dpt(4)
module after dpt.h 1.17, dpt_eisa.c 1.22 and dpt_scsi.c 1.55.
Breakage reported by: n_hibma
Linux SCSI SG passthrough device API. The intention is to allow for both
running of Linux apps that want to talk to /dev/sg* nodes, and to facilitate
porting of apps from Linux to FreeBSD. As such, both native and linuxolator
entry points and definitions are provided.
Caveats:
- This does not support the procfs and sysfs nodes that the Linux SG
driver provides. Some Linux apps may rely on these for operation,
others may only use them for informational purposes.
- More ioctls need to be implemented.
- Linux uses a naming scheme of "sg[a-z]" for devices, while FreeBSD uses a
scheme of "sg[0-9]". Devfs aliasis (symlinks) are automatically created
to link the two together. However, tools like camcontrol only see the
native names.
- Some operations were originally designed to return byte counts or other
data directly as the syscall return value. The linuxolator doesn't appear
to support this well, so this driver just punts for these cases.
Now that the driver is in place, others are welcome to add missing
functionality. Thanks to Roman Divacky for pushing this work along.
imitating an Ethernet device, so vlan(4) and if_bridge(4) can be
attached to it for testing and benchmarking purposes. Its source
can be an introduction to the anatomy of a network interface driver
due to its simplicity as well as to a bunch of comments in it.
o make all crypto drivers have a device_t; pseudo drivers like the s/w
crypto driver synthesize one
o change the api between the crypto subsystem and drivers to use kobj;
cryptodev_if.m defines this api
o use the fact that all crypto drivers now have a device_t to add support
for specifying which of several potential devices to use when doing
crypto operations
o add new ioctls that allow user apps to select a specific crypto device
to use (previous ioctls maintained for compatibility)
o overhaul crypto subsystem code to eliminate lots of cruft and hide
implementation details from drivers
o bring in numerous fixes from Michale Richardson/hifn; mostly for
795x parts
o add an optional mechanism for mmap'ing the hifn 795x public key h/w
to user space for use by openssl (not enabled by default)
o update crypto test tools to use new ioctl's and add cmd line options
to specify a device to use for tests
These changes will also enable much future work on improving the core
crypto subsystem; including proper load balancing and interposing code
between the core and drivers to dispatch small operations to the s/w
driver as appropriate.
These changes were instigated by the work of Michael Richardson.
Reviewed by: pjd
Approved by: re
uuencoded format along with their respective LICENSE files.
- Add new share/doc/legal directory to BSD.usr.dist mtree file. This is the
place we install LICENSE files for restricted firmwares.
- Teach firmware(9) and kmod.mk about licensed firmwares. Restricted firmwares
won't load properly unless legal.<name>.license_ack is set to 1, either
via kenv(1) or /boot/loader.conf.
Reviewed by: mlaier, sam
Permitted by: Intel (via Andrew Wilson)
MFC after: 1 month
arrangement that has no intrinsic internal knowledge of whether devices
it is given are truly multipath devices. As such, this is a simplistic
approach, but still a useful one.
The basic approach is to (at present- this will change soon) use camcontrol
to find likely identical devices and and label the trailing sector of the
first one. This label contains both a full UUID and a name. The name is
what is presented in /dev/multipath, but the UUID is used as a true
distinguishor at g_taste time, thus making sure we don't have chaos
on a shared SAN where everyone names their data multipath as "Fred".
The first of N identical devices (and N *may* be 1!) becomes the active
path until a BIO request is failed with EIO or ENXIO. When this occurs,
the active disk is ripped away and the next in a list is picked to
(retry and) continue with.
During g_taste events new disks that meet the match criteria for existing
multipath geoms get added to the tail end of the list.
Thus, this active/passive setup actually does work for devices which
go away and come back, as do (now) mpt(4) and isp(4) SAN based disks.
There is still a lot to do to improve this- like about 5 of the 12
recommendations I've received about it, but it's been functional enough
for a while that it deserves a broader test base.
Reviewed by: pjd
Sponsored by: IronPort Systems
MFC: 2 months
It is built in the same module as IPv4 multicast forwarding, i.e. ip_mroute.ko,
if and only if IPv6 support is enabled for loadable modules.
Export IPv6 forwarding structs to userland netstat(1) via sysctl(9).
