KBD_INSTALL_CDEV).
- Removed the note that the VESA option cannot be used on the SMP system;
this is not true.
- Moved the option VESA to more appropriate place.
- Refined internal interface in keyboard drivers so that:
1. the side effect of device probe is kept minimal,
2. polling mode function is added,
3. and new ioctl and configuration options are added (see below).
- Added new ioctl: KDSETREPEAT
Set keyboard typematic rate. There has existed an ioctl command,
KDSETRAD, for the same purpose. However, KDSETRAD is dependent on
the AT keyboard. KDSETREPEAT provides more generic interface.
KDSETRAD will still be supported in the atkbd driver.
- Added new configuration options:
ATKBD_DFLT_KEYMAP
Specify a keymap to be used as the default, built-in keymap.
(There has been undocumented options, DKKEYMAP, UKKEYMAP, GRKEYMAP,
SWKEYMAP, RUKEYMAP, ESKEYMAP, and ISKEYMAP to set the default keymap.
These options are now gone for good. The new option is more general.)
KBD_DISABLE_KEYMAP_LOADING
Don't allow the user to change the keymap.
Move the Olicom token ring driver to the officially sanctionned location of
/sys/contrib. Also fix some brokenness in the generic token ring support.
Be warned that if_dl.h has been changed and SOME programs might
like recompilation.
The i++ loop from 1..1000 is too small on very fast machines like
PII 450 MHz. Increasing the loop from 1..100000 lets the machine
access PHY. After this patch it's possible to use a SMC PCI card
on a HP Kayak XA series PC Workstation. Workaround until this fix
was to enable debugging in the driver (#define EPIC_DEBUG 1).
Without that patch you get an undefined state:
while true
do
ifconfig -a | grep status:
done
The status messages flaps between twwo values, but not
"connected".
Obtained from: Ustimenko Semen <semen@iclub.nsu.ru>
determine IRQ and DRQ information.
Fix a bug that would cause us to attempt to retrieve extended sync
rate information on cards/firmware revs that do not support that command.
config info. On early revision cards (742a), the EISA register space,
other than the location used to determine the address of the card's main
command ports, is write only.
This code is backwards compatible with the older "microkernel" PLL, but
allows ntpd v4 to use nanosecond resolution. Many other improvements.
PPS_SYNC and hardpps() are NOT supported yet.
Also, unbreak the breakage introduced at the last revision of module.c.
This changes the semantics of mod_searchfile() (and mod_searchmodule())
to make the caller's responsibility freeing the buffer returned. This
is different from other functions in loader's code, and was done as a
fix for kern/9631. If someone wants to revert this to the original
behavior, don't forget to fix kern/9631 in another way.
This should also fix bin/10462, which was introduced as a result of the
first try at kern/9631 (module.c last revision).
PR: bin/10462
Submitted by: Takanori Saneto <sanewo@ba2.so-net.ne.jp>
trouble with tagged queueing as the 6.5 gig version.
So, I've added a quirk entry for it to limit it to two outstanding
transactions at a time, just like the 6.5G version. While I'm at it, add a
quirk for the 9G version of the drive, since it most likely has the same
problem.
Submitted by: Jeremy Lea <reg@shale.csir.co.za>
reports on those most welcome!
Fixed problems:
Hang on probe on "fantom" devices.
The probe now use a timeout to avoid hangs if no interrupt
is recevied.
There has also been more general code clenaups, and some reorgs.
lock) until it actually needs to modify the vm_map.
Note: it is legal to modify vm_map::hint without holding a write lock.
Submitted by: "Richard Seaman, Jr." <dick@tar.com> with minor changes
by myself.
