in symtab_get method symtab parameter is made constant as this reflects
actual intention and usage of the method
Reviewed by: imp, current@
Approved by: jhb (mentor)
- Preallocate some memory for ACPI tasks early enough. We cannot use
malloc(9) any more because spin mutex may be held here. The reserved
memory can be tuned via debug.acpi.max_tasks tunable or ACPI_MAX_TASKS
in kernel configuration. The default is 32 tasks.
- Implement a custom taskqueue_fast to wrap the new memory allocation.
This implementation is not the fastest in the world but we are being
conservative here.
routine and save the resources using a chipset-data structure. Use these
preallocated resources to setup resources for the SATA channels to avoid
asking the PCI bus to allocate the same BAR multiple times.
Tested by: bms
MFC after: 1 week
controller. These controllers are also known as L1C(AR8131) and
L2C(AR8132) respectively. These controllers resembles the first
generation controller L1 but usage of different descriptor format
and new register mappings over L1 register space requires a new
driver. There are a couple of registers I still don't understand
but the driver seems to have no critical issues for performance and
stability. Currently alc(4) supports the following hardware
features.
o MSI
o TCP Segmentation offload
o Hardware VLAN tag insertion/stripping
o Tx/Rx interrupt moderation
o Hardware statistics counters(dev.alc.%d.stats)
o Jumbo frame
o WOL
AR8131/AR8132 also supports Tx checksum offloading but I disabled
it due to stability issues. I'm not sure this comes from broken
sample boards or hardware bugs. If you know your controller works
without problems you can still enable it. The controller has a
silicon bug for Rx checksum offloading, so the feature was not
implemented.
I'd like to say big thanks to Atheros. Atheros kindly sent sample
boards to me and answered several questions I had.
HW donated by: Atheros Communications, Inc.
driver should read updated status back after issuing a SCB command.
To send a command to controller and read updated status back,
driver should synchronize both memory read and write operations
with device. Fix bus_dmamap_sync operation specifier used in
fxp_dma_wait() by adding both memory read and memory write
operations.
a _BBN value of 0 if it was for the first bridge encountered since some
older systems returned _BBN of 0 for all bridges. However, some newer
systems enumerate bridges with non-zero _BBN before bus 0 which is
perfectly valid. Handle both cases by trusting the first bridge that has
a _BBN of 0 and falling back to reading from non-standard config registers
only for subsequent bridges with a _BBN of 0. We also only perform this
check for segment (domain) 0. We assume that _BBN is always correct
for segments other than 0.
Tested by: Josef Moellers josef.moellers at fujitsu
MFC after: 1 week
- The return value should be a signed integer, because -1 means failure.
- The c variable should be unsigned, to force it to be zero-extended
when returned.
Reported by: Andreas Tobler <andreast-list fgznet ch>
the ROUTETABLES kernel option thus there is no need to include opt_route.h
anymore in all consumers of vnet.h and no longer depend on it for module
builds.
Remove the hidden include in flowtable.h as well and leave the two
explicit #includes in ip_input.c and ip_output.c.
For a slightly thorough explaination, please refer to
[1] http://people.freebsd.org/~ariff/SOUND_4.TXT.html .
Summary of changes includes:
1 Volume Per-Channel (vpc). Provides private / standalone volume control
unique per-stream pcm channel without touching master volume / pcm.
Applications can directly use SNDCTL_DSP_[GET|SET][PLAY|REC]VOL, or for
backwards compatibility, SOUND_MIXER_PCM through the opened dsp device
instead of /dev/mixer. Special "bypass" mode is enabled through
/dev/mixer which will automatically detect if the adjustment is made
through /dev/mixer and forward its request to this private volume
controller. Changes to this volume object will not interfere with
other channels.
Requirements:
- SNDCTL_DSP_[GET|SET][PLAY|REC]_VOL are newer ioctls (OSSv4) which
require specific application modifications (preferred).
- No modifications required for using bypass mode, so applications
like mplayer or xmms should work out of the box.
Kernel hints:
- hint.pcm.%d.vpc (0 = disable vpc).
Kernel sysctls:
- hw.snd.vpc_mixer_bypass (default: 1). Enable or disable /dev/mixer
bypass mode.
- hw.snd.vpc_autoreset (default: 1). By default, closing/opening
/dev/dsp will reset the volume back to 0 db gain/attenuation.
Setting this to 0 will preserve its settings across device
closing/opening.
- hw.snd.vpc_reset (default: 0). Panic/reset button to reset all
volume settings back to 0 db.
- hw.snd.vpc_0db (default: 45). 0 db relative to linear mixer value.
2 High quality fixed-point Bandlimited SINC sampling rate converter,
based on Julius O'Smith's Digital Audio Resampling -
http://ccrma.stanford.edu/~jos/resample/. It includes a filter design
script written in awk (the clumsiest joke I've ever written)
- 100% 32bit fixed-point, 64bit accumulator.
- Possibly among the fastest (if not fastest) of its kind.
- Resampling quality is tunable, either runtime or during kernel
compilation (FEEDER_RATE_PRESETS).
- Quality can be further customized during kernel compilation by
defining FEEDER_RATE_PRESETS in /etc/make.conf.
Kernel sysctls:
- hw.snd.feeder_rate_quality.
0 - Zero-order Hold (ZOH). Fastest, bad quality.
1 - Linear Interpolation (LINEAR). Slightly slower than ZOH,
better quality but still does not eliminate aliasing.
2 - (and above) - Sinc Interpolation(SINC). Best quality. SINC
quality always start from 2 and above.
Rough quality comparisons:
- http://people.freebsd.org/~ariff/z_comparison/
3 Bit-perfect mode. Bypasses all feeder/dsp effects. Pure sound will be
directly fed into the hardware.
4 Parametric (compile time) Software Equalizer (Bass/Treble mixer). Can
be customized by defining FEEDER_EQ_PRESETS in /etc/make.conf.
5 Transparent/Adaptive Virtual Channel. Now you don't have to disable
vchans in order to make digital format pass through. It also makes
vchans more dynamic by choosing a better format/rate among all the
concurrent streams, which means that dev.pcm.X.play.vchanformat/rate
becomes sort of optional.
6 Exclusive Stream, with special open() mode O_EXCL. This will "mute"
other concurrent vchan streams and only allow a single channel with
O_EXCL set to keep producing sound.
Other Changes:
* most feeder_* stuffs are compilable in userland. Let's not
speculate whether we should go all out for it (save that for
FreeBSD 16.0-RELEASE).
* kobj signature fixups, thanks to Andriy Gapon <avg@freebsd.org>
* pull out channel mixing logic out of vchan.c and create its own
feeder_mixer for world justice.
* various refactoring here and there, for good or bad.
* activation of few more OSSv4 ioctls() (see [1] above).
* opt_snd.h for possible compile time configuration:
(mostly for debugging purposes, don't try these at home)
SND_DEBUG
SND_DIAGNOSTIC
SND_FEEDER_MULTIFORMAT
SND_FEEDER_FULL_MULTIFORMAT
SND_FEEDER_RATE_HP
SND_PCM_64
SND_OLDSTEREO
Manual page updates are on the way.
Tested by: joel, Olivier SMEDTS <olivier at gid0 d org>, too many
unsung / unnamed heroes.
in Freescale system-on-chip devices.
The following algorithms and schemes are currently supported:
- 3DES, AES, DES
- MD5, SHA1, SHA256, SHA384, SHA512
Reviewed by: philip
Obtained from: Freescale, Semihalf
These two drivers seem to be the last consumers of clists. clists are
quite overengineered for simple circular buffers, so I'm adding similar
buffer management routines to the kbd and kbdmux drivers. The input
buffer is now part of the softc structures, instead of having
dynamically allocated cblocks.
ICIDU NI-707503 which is donated by Nick Hibma (great thanks!). Though
it has a MAXIM RF (0x8) there's some success reports with using GCT RF
(0x9) codes and it worked well for ICIDU NI-707503 too. So codes for
MAXIM and GCT RFs are integrated.
Before this commit, if I rememeber correctly, MAXIM RF is never tested
that it seems it's a first report working with FreeBSD.
- always maintain byte/mcast/drop stats via drbr
- move #define of IFNET_BUF_RING so that its picked
up by all files in the driver
- conditionalize IFNET_BUF_RING on the FreeBSD_version
bump just after it appeared in the tree.
Sponsored by: Myricom Inc.
These controllers use newer descriptor format and the new descriptor
format uses status LE to indicate the status of checksum. Rx
checksummed value used in previous controllers were very cryptic
and I failed to understand how to use them. In addition most
controllers in previous generations had Rx checksum offloading bug.
While I'm here introduce a MSK_FLAG_NORX_CSUM flag to bypass
checking Rx checksum offloading as Yukon FE+ A0 has status LE bug.
this feature hardware automatically computes TCP/UDP payload
offset. Introduce MSK_FLAG_AUTOTX_CSUM to mark the capability.
Yukon Extreme B0 revision is known to have a silicon for the
feature so disable it. Yukon Extreme B0 still can do Tx checksum
offloading but CPU have to compute TCP/UDP payload offset. To
enable traditional checksum offloading, disable automatic Tx
checksum calculation capability.
Yukon Extreme A0 revision could not use store-and-forward mode for
jumbo frames(silicon bug) so disable Tx checksum offloading for
jumbo frames.
I believe controllers that have MSK_FLAG_AUTOTX_CSUM capability or
new descriptor format do not have Tx checksum offload bug so
disable checksum offloading workaround for for short frames.
Tested by: jhb, Warren Block ( wblock <> wonkity dot com )
Yukon Extreme uses new descriptor format for TSO and has Tx frame
parser which greatly reduces CPU cycles spent in computing TCP/UDP
payload offset calculation in Tx checksum offloading path. The new
descriptor format also removed TCP/UDP payload computation for TSO
which in turn results in better TSO performance. It seems Yukon
Extreme has a lot of new (unknown) features but only basic
offloading is supported at this time. So far there are two known
issues.
o Sometimes Rx overrun errors happen when pulling data over
gigabit link. Running over 100Mbps seem to ok.
o Ethernet hardware address shows all-zeroed value on 88E8070.
Assigning ethernet address with ifconfig is necessary to make it
work.
Support for Yukon Extreme is not perfect but it would be better
than having a non-working device. Special thanks to jbh who fixed
several bugs of initial patch.
Tested by: jhb, Warren Block ( wblock <> wonkity dot com )
- Each socket upcall is now invoked with the appropriate socket buffer
locked. It is not permissible to call soisconnected() with this lock
held; however, so socket upcalls now return an integer value. The two
possible values are SU_OK and SU_ISCONNECTED. If an upcall returns
SU_ISCONNECTED, then the soisconnected() will be invoked on the
socket after the socket buffer lock is dropped.
- A new API is provided for setting and clearing socket upcalls. The
API consists of soupcall_set() and soupcall_clear().
- To simplify locking, each socket buffer now has a separate upcall.
- When a socket upcall returns SU_ISCONNECTED, the upcall is cleared from
the receive socket buffer automatically. Note that a SO_SND upcall
should never return SU_ISCONNECTED.
- All this means that accept filters should now return SU_ISCONNECTED
instead of calling soisconnected() directly. They also no longer need
to explicitly clear the upcall on the new socket.
- The HTTP accept filter still uses soupcall_set() to manage its internal
state machine, but other accept filters no longer have any explicit
knowlege of socket upcall internals aside from their return value.
- The various RPC client upcalls currently drop the socket buffer lock
while invoking soreceive() as a temporary band-aid. The plan for
the future is to add a new flag to allow soreceive() to be called with
the socket buffer locked.
- The AIO callback for socket I/O is now also invoked with the socket
buffer locked. Previously sowakeup() would drop the socket buffer
lock only to call aio_swake() which immediately re-acquired the socket
buffer lock for the duration of the function call.
Discussed with: rwatson, rmacklem
using bus_dmamap_load_mbuf_sg() on it. This
prevents data corruption when the mxge MTU is
between 4076 and 8172 on machines with 4KB
pages and MXGE_VIRT_JUMBOS is in use (which it
isn't, in -current or -stable)
mic inputs. I have no idea what for it was made that time, but now I have
several reports that it should be removed to make microphones work. If
this quirk is still required for some systems then they should be identified
and specified explicitly.
Because we only support a single argument to tf_param, use 16 bits for
the pitch and 16 bits for the duration. While there, make the argument
unsigned. There isn't a single param call that needs a signed integer.
Submitted by: danfe (modified)
part identified as Sunplus Technology Inc. This
happens to sit in a Rosewill RX81U-ES-25A 2.5" SATA
to USB 2.0 external enclosure.
Reviewed by: Hans Petter Selasky
CPU for too long period than necessary. Additively, interfaces are kept
polled (in the tick) even if no more packets are available.
In order to avoid such situations a new generic mechanism can be
implemented in proactive way, keeping track of the time spent on any
packet and fragmenting the time for any tick, stopping the processing
as soon as possible.
In order to implement such mechanism, the polling handler needs to
change, returning the number of packets processed.
While the intended logic is not part of this patch, the polling KPI is
broken by this commit, adding an int return value and the new flag
IFCAP_POLLING_NOCOUNT (which will signal that the return value is
meaningless for the installed handler and checking should be skipped).
Bump __FreeBSD_version in order to signal such situation.
Reviewed by: emaste
Sponsored by: Sandvine Incorporated
The system hostname is now stored in prison0, and the global variable
"hostname" has been removed, as has the hostname_mtx mutex. Jails may
have their own host information, or they may inherit it from the
parent/system. The proper way to read the hostname is via
getcredhostname(), which will copy either the hostname associated with
the passed cred, or the system hostname if you pass NULL. The system
hostname can still be accessed directly (and without locking) at
prison0.pr_host, but that should be avoided where possible.
The "similar information" referred to is domainname, hostid, and
hostuuid, which have also become prison parameters and had their
associated global variables removed.
Approved by: bz (mentor)
I don't want people to override the mutex when allocating a TTY. It has
to be there, to keep drivers like syscons happy. So I'm creating a
tty_alloc_mutex() which can be used in those cases. tty_alloc_mutex()
should eventually be removed.
The advantage of this approach, is that we can just remove a function,
without breaking the regular API in the future.
Calculate the exact number of vectors we'll use before calling
pci_alloc_msix. Don't grab nine all the time.
Call cxgb_setup_interrupts once per T3, not once per port. Ditto
for cxgb_teardown_interrupts.
Don't leak resources when interrupt setup fails in the middle.
Obtained from: Navdeep Parhar
MFC after: 10 days
- add key mappings for fn keys
- byte swapping for certain models
- Fix leds for keyboards which require an ID byte for the HID output structures
Submitted by: Hans Petter Selasky
to dequeue a packet.
The tx path was trying to ensure that enough Xenbus TX ring slots existed but
it didn't check to see whether the mbuf TX ring slots were also available.
They get freed in xn_txeof() which occurs after transmission, rather than earlier
on in the process. (The same happens under Linux too.)
Due to whatever reason (CPU use, scheduling, memory constraints, whatever) the
mbuf TX ring may not have enough slots free and would allocate slot 0. This is
used as the freelist head pointer to represent "free" mbuf TX ring slots; setting
this to an actual mbuf value rather than an id crashes the code.
This commit introduces some basic code to track the TX mbuf ring use and then
(hopefully!) ensures that enough slots are free in said TX mbuf ring before it
enters the actual work loop.
A few notes:
* Similar logic needs to be introduced to check there are enough actual slots
available in the xenbuf TX ring. There's some logic which is invoked earlier
but it doesn't hard-check against the number of available ring slots.
Its trivial to do; I'll do it in a subsequent commit.
* As I've now commented in the source, it is likely possible to deadlock the
driver under certain conditions where the rings aren't receiving any changes
(which I should enumerate) and thus Xen doesn't send any further software
interrupts. I need to make sure that the timer(s) are running right and
the queues are periodically kicked.
PR: 134926
Slot 0 must always remain "free" and be a pointer to the first free entry in the
mbuf descriptor list. It is thus an error to have code allocate or push slot 0
back into the list.
get a quick snapshot of the kernel's symbol table including the symbols
from any loaded modules (the symbols are all merged into one symbol
table). Unlike like other implementations, this ksyms driver maps
memory in the process memory space to store the snapshot at the time
/dev/ksyms is opened. It also checks to see if the process has already
a snapshot open and won't allow it to open /dev/ksyms it again until it
closes first. This prevents kernel and process memory from being
exhausted. Note that /dev/ksyms is used by the lockstat(1) command.
Reviewed by: gallatin kib (freebsd-arch)
Approved by: gnn (mentor)
severe silicon bugs that can't handle VLAN hardware tagging as well
as status LE writeback bug. The status LE writeback bug is so
critical we can't trust status word of received frame. To accept
frames on Yukon FE+ A0 msk(4) just do minimal check for received
frames and pass them to upper stack. This means msk(4) can pass
corrupted frames to upper layer. You have been warned!
Also I supposed RX_GMF_FL_THR to be 32bits register but Linux
driver treated it as 16bit register so follow their leads. At least
this does not seem to break msk(4) on Yukon FE+.
Tested by: bz, Tanguy Bouzeloc ( the.zauron <> gmail dot com )
Bruce Cran ( bruce <> cran dot org dot uk )
Michael Reifenberger ( mike <> reifenberger dot com )
Stephen Montgomery-Smith ( stephen <> missouri dot edu )
Yukon FE+ is fast ethernet controller and uses new descriptor
format. Since I don't have this controller, the support code was
written from guess and various feedback from enthusiastic users.
Thanks to all users who patiently tested my initial patches.
Special thanks to Tanguy Bouzeloc who fixed critical bug of initial
patch.
Tested by: bz, Tanguy Bouzeloc ( the.zauron <> gmail dot com )
Bruce Cran ( bruce <> cran dot org dot uk )
Michael Reifenberger ( mike <> reifenberger dot com )
Stephen Montgomery-Smith ( stephen <> missouri dot edu )
The GM_GP_CTRL register may have stale content from previous link
information so clearing it will make hardware update the register
correctly when it established a valid link.
While I'm here remove stale comment.
does not guarantee established link. Also 1000baseT link report for
fast ethernet controller is not valid one so make sure gigabit link
is allowed for this controller.
Whenever we lost link, check whether Rx/Tx MACs were enabled. If both
MAC are not active, do not try to disable it again.
mark controller's capability. Controllers that have jumbo frame
support sets MSK_FLAG_JUMBO, and controllers that does not support
checksum offloading for jumbo frames will set MSK_FLAG_JUMBO_NOCSUM.
For Fast Ethernet controllers it will set MSK_FLAG_FASTETHER and it
would be used in link state handling.
While here, disable Tx checksum offloading if jumbo frame is used
on controllers that does not have Tx checksum offloading capability
for jumbo frame(e.g. Yukon EC Ultra).
FE+ controller. Due to the severe silicon bugs for Yukon FE+,
88E3016 seems to require more workarounds. However I'm not sure
whether the workaround is PHY specific or only applicable to Yukon
FE+. The datasheet for the PHY is publicly available but it lacks
several details for the workaround used in this change. The
workaround information was obtained from Linux. Many thanks to
Yukon FE+ users who helped me add 88E3016 support.
Tested by: bz, Tanguy Bouzeloc ( the.zauron <> gmail dot com )
Bruce Cran ( bruce <> cran dot org dot uk )
Michael Reifenberger ( mike <> reifenberger dot com )
Stephen Montgomery-Smith ( stephen <> missouri dot edu )
advertisement register. Some PHYs such as 88E3016 requires NEXT
Page capability to establish valid link. Also set protocol selector
field which is read only but it makes the intention clearer.
is valid only for auto-negotiation case so check the bit if we know
auto-negotiation is active. While I'm here explicitly checks
current speed with speed mask and set IFM_NONE if resolved speed
is unknown.
checks extended status register to see whether the PHY is fast
ethernet or not. This removes a lot of checks for specific PHY
models and it makes easy to add more PHYs to e1000phy(4).
While I'm here remove setting mii_anegticks as it is set with
mii_phy_add_media().
Remove PAGE_SIZE alignment used in Rx buffer DMA tag creation. The
alignment restriction was used in old local jumbo allocator and
nfe(4) switched to UMA backed page allocator for jumbo frame.
This change should fix jumbo buffer allocation failure.
Reported by: Pascal Braun ( pascal.braun <> continum dot net )
only if prepping the adapter failed.
Slight adjustment to comments.
Fix a bug whereby downing the interface didn't preven it from
processing packets.
Submitted by: Navdeep Parhar
MFC after: 1 week
Some hardware easily comes out of sync with regard to whether the current or
the next control transfer should be stalled, if a stall command is always
issued before receiving the SETUP packet. After this patch the stall command
will only be issued when a transfer should actually be stalled.
Submitted by: Hans Petter Selasky
1) Add a sysctl that will say what type of PHYs exist on the card.
2) Fix a bug that occurs when an AEL 2005 PHY resets without a transciever
in the card.
3) Unify the PHY link detection code.
Obtained from: Navdeep Parhar
MFC after: 10 days
and down more cleanly. This addresses a problem where if we have the
link flap during boot the driver would lock up the system.
Reviewed by: jhb
MFC after: 1 week
thread. Multiple RAID events in quick succession can cause an additional
bus rescan to be scheduled before an earlier scan has completed. In this
case the driver was attempting to use the same CCB storage for two requests.
PR: kern/130330
Reviewed by: Riccardo Torrini riccardo.torrini | esaote com
MFC after: 1 week
o Header file cleanup.
o bus_dma(9) conversion.
- Removed all consumers of vtophys(9) and converted to use
bus_dma(9).
- 64bit DMA support was disabled because DP83821 is not capable
of handling the DMA request. 64bit DMA request on DP83820
requires different descriptor structures and it's hard to
dynamically change descriptor format at run time so I disabled
it. Note, this is the same behavior as previous one but
previously nge(4) didn't explicitly disable 64bit mode on
DP83820.
- Added Tx/Rx descriptor ring alignment requirements(8 bytes
alignment).
- Limit maximum number of Tx DMA segments to 16. In fact,
controller does not seem to have limitations on number of Tx
DMA segments but 16 should be enough for most cases and
m_collapse(9) will handle highly fragmented frames without
consuming a lot of CPU cycles.
- Added Rx buffer alignment requirements(8 bytes alignment). This
means driver should fixup received frames to align on 16bits
boundary on strict-alignment architectures.
- Nuked driver private data structure in descriptor ring.
- Added endianness support code in Tx/Rx descriptor access.
o Prefer faster memory mapped register access to I/O mapped access.
Added fall-back mechanism to use alternative register access.
The hardware supports both memory and I/O mapped access.
o Added suspend/resume methods but it wasn't tested as controller I
have does not support PCI PME.
o Removed swap argument in nge_read_eeprom() since endianness
should be handled after reading EEPROM.
o Implemented experimental 802.3x full-duplex flow-control. ATM
it was commented out but will be activated after we have generic
flow-control framework in mii(4) layer.
o Rearranged promiscuous mode settings and simplified logic.
o Always disable Rx filter prior to changing Rx filter functions as
indicated in DP83820/DP83821 datasheet.
o Added an explicit DELAY in timeout loop of nge_reset().
o Added a sysctl variable dev.nge.%d.int_holdoff to control
interrupt moderation. Valid ranges are 1 to 255(default 1) in
units of 100us. The actual delivery of interrupt would be delayed
based on the sysctl value. The interface has to be brought down
and up again before a change takes effect. With proper tuning
value, users do not need to resort to polling(4) anymore.
o Added ALTQ(4) support.
o Added missing IFCAP_VLAN_HWCSUM as nge(4) can offload Tx/Rx
checksum calculation on VLAN tagged frames as well as VLAN tag
insertion/stripping. Also add IFCAP_VLAN_MTU capability as nge(4)
can handle VLAN tagged oversized frames.
o Fixed media header length for VLAN.
o Rearranged nge_detach routine such that it's now used for general
clean-up routine.
o Enabled MWI.
o Accessing EEPROM takes very long time so read 6 bytes ethernet
address with one call instead of 3 separate accesses.
o Don't set if_mtu in device attach, it's already set in
ether_ifattach().
o Don't do any special things for TBI interface. Remove TBI
specific media handling in the driver and have gentbi(4) handle
it. Add glue code to read/write TBI PHY registers in miibus
method. This change removes a lot of PHY handling code in driver
and now its functionality is handled by mii(4).
o Alignment fixup code is now applied only for strict-alignment
architectures. Previously the code was applied for all
architectures except i386. With this change amd64 will get
instant Rx performance boost.
o When driver fails to allocate a new mbuf, update if_qdrops so
users can see what was wrong in Rx path.
o Added a workaround for a hardware bug which resulted in short
VLAN tagged frames(e.g. ARP) was rejected as if runt frame was
received. With this workaround nge(4) now accepts the short VLAN
tagged frame and nge(4) can take full advantage of hardware VLAN
tag stripping. I have no idea how this bug wasn't known so far,
without the workaround nge(4) may never work on VLAN
environments.
o Fixed Rx checksum offload logic such that it now honors active
interface capability configured with ifconfig(8).
o In nge_start()/nge_txencap(), always leave at least one free
descriptor as indicated in datasheet. Without this the hardware
would be confused with ring descriptor structure(e.g. no clue
for the end of descriptor ring).
o Removed dead-code that checks interrupts on PHY hardware. The
code was designed to detect link state changes but it was
disabled as driving nge_tick clock would break auto-negotiation
timer. This code is no longer needed as nge(4) now uses mii(4)
and link state change handling is done with mii callback.
o Rearranged ethernet address programming logic such that it works
on strict-alignment architectures.
o Added IFCAP_VLAN_HWTAGGING/IFCAP_VLAN_HWCSUM handler in
nge_ioctl() such that the functionality is configurable with
ifconfig(8). DP83820/DP83821 can do checksum offload for VLAN
tagged frames so enable Tx/Rx checksum offload for VLAN
interfaces.
o Simplified IFCAP_POLLING selection logic in nge_ioctl().
o Fixed module unload panic when bpf listeners are active.
o Tx/Rx descriptor ring address uses 64bit DMA address for
readability. High address part of DMA would be 0 as nge(4)
disabled 64bit DMA transfers so it's ok for DP83821.
o Removed volatile keyword in softc as bus_dmamap_sync(9) should
take care of this.
o Removed extra driver private structures in descriptor ring. These
extra elements are not part of descriptor structure. Embedding
private driver structure into descriptor ring is not good idea
as its size may be different on 32bit/64bit architectures.
o Added miibus_linkchg method handler to catch link state changes.
o Removed unneeded nge_ifmedia in softc. All TBI access is handled
in gentbi(4). There is no difference between TBI and non-TBI case
now.
o Removed "gigabit link up" message handling in nge_tick. Link
state change notification is already performed by mii(4) and
checking link state by accessing PHY registers in periodic timer
handler of driver is wrong. All link state and speed/duplex
monitoring should be handled in PHY driver.
o Use our own timer for watchdog instead of if_watchdog/if_timer
interface.
o Added hardware MAC statistics counter, users canget current MAC
statistics from dev.nge.%d.stats sysctl node(%d is unit number of
a device).
o Removed unused macros, NGE_LASTDESC, NGE_MODE, NGE_OWNDESC,
NGE_RXBYTES.
o Increased number of Tx/Rx descriptors from 128 to 256. From my
experience on gigabit ethernet controllers, number of descriptors
should be 256 or higher to get an optimal performance on gigabit
link.
o Increased jumbo frame length to 9022 bytes to cope with other
gigabit ethernet drivers. Experimentation shows no problems with
9022 bytes.
o Removed unused member variables in softc.
o Switched from bus_space_{read|write}_4 to bus_{read|write}_4.
o Added support for WOL.
o replace DLT_IEEE802_11 support in net80211 with DLT_IEEE802_11_RADIO
and remove explicit bpf support from wireless drivers; drivers now
use ieee80211_radiotap_attach to setup shared data structures that
hold the radiotap header for each packet tx/rx
o remove rx timestamp from the rx path; it was used only by the tdma support
for debugging and was mostly useless due to it being 32-bits and mostly
unavailable
o track DLT_IEEE80211_RADIO bpf attachments and maintain per-vap and
per-com state when there are active taps
o track the number of monitor mode vaps
o use bpf tap and monitor mode vap state to decide when to collect radiotap
state and dispatch frames; drivers no longer explicitly directly check
bpf state or use bpf calls to tap frames
o handle radiotap state updates on channel change in net80211; drivers
should not do this (unless they bypass net80211 which is almost always
a mistake)
o update various drivers to be more consistent/correct in handling radiotap
o update ral to include TSF in radiotap'd frames
o add promisc mode callback to wi
Reviewed by: cbzimmer, rpaulo, thompsa
bug referencing a destroyed lock within TX callbacks during device
detach.
Submitted by: hps (original version)
Tested by: Lucius Windschuh <lwindschuh at googlemail.com>
possible future I-cache coherency operation can succeed. On ARM
for example the L1 cache can be (is) virtually mapped, which
means that any I/O that uses temporary mappings will not see the
I-cache made coherent. On ia64 a similar behaviour has been
observed. By flushing the D-cache, execution of binaries backed
by md(4) and/or NFS work reliably.
For Book-E (powerpc), execution over NFS exhibits SIGILL once in
a while as well, though cpu_flush_dcache() hasn't been implemented
yet.
Doing an explicit D-cache flush as part of the non-DMA based I/O
read operation eliminates the need to do it as part of the
I-cache coherency operation itself and as such avoids pessimizing
the DMA-based I/O read operations for which D-cache are already
flushed/invalidated. It also allows future optimizations whereby
the bcopy() followed by the D-cache flush can be integrated in a
single operation, which could be implemented using on-chips DMA
engines, by-passing the D-cache altogether.
register 0x52, not ctrl1. This appears to be a mistake in the bcm
reverse engineering page, and has been corrected there. Tracing
through the code, this is more in keeping with the "documented"
register. Sephe thinks it looks interesting and may be worth
fixing. :)
Submitted by: ddkprog at yahoo com
Reviewed by: Sepherosa Ziehau
- In bce_rx_intr(), use BUS_DMASYNC_POSTREAD instead of
BUS_DMASYNC_POSTWRITE, as we want to "read" from the
rx page chain pages.
- Document why we need to do PREWRITE after we have updated
the rx page chain pages.
- In bce_intr(), use BUS_DMASYNC_POSTREAD and
BUS_DMASYNC_PREREAD when before and after CPU "reading"
the status block.
- Adjust some nearby style mismatches/etc.
Pointed out by: yongari
Approved by: davidch (no objection) but bugs are mine :)
# Note: The driver doesn't support either these PHY types, so this is
# effectively a nop.
Submitted by: "ddk"
Obtained from: http://paradox.lissyara.su/bwi.diff
believe it was a BCM4319. However, it is the a/b/g variation of the
BCM4318. The chip itself is labelled BCM4318EKFBG, and the board is
BCM94318MKABG.
Paradox's patch includes the type of 802.11 wireless for each card,
but changes all the names (I don't think the latter is quite right).
Import that part of the patch, but keep the current set of BCM names
(with a minor tweak for the 4306 ones). I'll need to verify them via
some other means.
Obtained from: http://paradox.lissyara.su/bwi.diff (partially)
Apart from the 16 virtual terminals, Syscons allocates two device nodes
that should not really be TTYs, even though they are. One of them is
consolectl. In RELENG_7 and before, these device nodes are used in
single user mode. After I simplified input path, we only use this device
node to call ioctl() on (moused, Xorg, vidcontrol).
When you call ioctl() on consolectl, it will behave the same as being
called on the first window.
drops and re-grabs the softc mutex in the middle, resulting in kernel
trap 12. This may happen when a lot of traffic is being hammered on
one bge(4) interface while the system is shutting down.
Reported by: Alexander Sack <pisymbol gmail com>
PR: kern/134548
MFC After: 2 weeks
chipset-specific code to attach chipset-specific data.
- Use chipset-specific data in the acard and promise chipsets rather than
changing the ivars of ATA PCI devices. ivars are reserved for use by the
parent bus driver and are _not_ available for use by devices directly.
This fixes a panic during sysctl -a with certain Promise controllers with
ACPI enabled.
Reviewed by: mav
Tested by: Magnus Kling (kingfon @ gmail) (on 7)
MFC after: 3 days
NULL or change it. We initialize it before we set if_ioctl. It can
therefore never be NULL, and most other drivers don't bother with this
sanity check.
As an experiment, I changed snp(4) to use a mutex instead of an sx lock.
We can't enable this right now, because Syscons still picks up Giant.
It's nice to already have the framework there.
adapted to MPSAFE cam(4) to a isp(4) specific callout structure.
Thanks to Florian Smeets for providing access to a machine exhibiting
this problem for debugging.
Approved by: mjacob
MFC after: 3 days
sc_rixmap is an inverse map
NB: could eliminate the check for an invalid rate by filling in 0 for
invalid entries but the rate control modules use it to identify
bogus rates so leave it for now
previously always pointing to the default vnet context, to a
dynamically changing thread-local one. The currvnet context
should be set on entry to networking code via CURVNET_SET() macros,
and reverted to previous state via CURVNET_RESTORE(). Recursions
on curvnet are permitted, though strongly discuouraged.
This change should have no functional impact on nooptions VIMAGE
kernel builds, where CURVNET_* macros expand to whitespace.
The curthread->td_vnet (aka curvnet) variable's purpose is to be an
indicator of the vnet context in which the current network-related
operation takes place, in case we cannot deduce the current vnet
context from any other source, such as by looking at mbuf's
m->m_pkthdr.rcvif->if_vnet, sockets's so->so_vnet etc. Moreover, so
far curvnet has turned out to be an invaluable consistency checking
aid: it helps to catch cases when sockets, ifnets or any other
vnet-aware structures may have leaked from one vnet to another.
The exact placement of the CURVNET_SET() / CURVNET_RESTORE() macros
was a result of an empirical iterative process, whith an aim to
reduce recursions on CURVNET_SET() to a minimum, while still reducing
the scope of CURVNET_SET() to networking only operations - the
alternative would be calling CURVNET_SET() on each system call entry.
In general, curvnet has to be set in three typicall cases: when
processing socket-related requests from userspace or from within the
kernel; when processing inbound traffic flowing from device drivers
to upper layers of the networking stack, and when executing
timer-driven networking functions.
This change also introduces a DDB subcommand to show the list of all
vnet instances.
Approved by: julian (mentor)
Broadcom BCM43xx chipsets. This driver uses the v3 firmware that
needs to be fetched separately. A port will be committed to create
the bwi firmware module.
The driver matches the following chips: Broadcom BCM4301, BCM4307,
BCM4306, BCM4309, BCM4311, BCM4312, BCM4318, BCM4319
The driver works for 802.11b and 802.11g.
Limitations:
This doesn't support the 802.11a or 802.11n portion of radios.
Some BCM4306 and BCM4309 cards don't work with Channel 1, 2 or 3.
Documenation for this firmware is reverse engineered from
http://bcm.sipsolutions.net/
V4 of the firmware is needed for 11a or 11n support
http://bcm-v4.sipsolutions.net/
Firmware needs to be fetched from a third party, port to be committed
# I've tested this with a BCM4319 mini-pci and a BCM4318 CardBus card, and
# not connected it to the build until the firmware port is committed.
Obtained from: DragonFlyBSD, //depot/projects/vap
Reviewed by: sam@, thompsa@
leading to a bug, when C-state does not decrease on sleep shorter then
declared transition latency. Fixing this deprecates workaround for broken
C-states on some hardware.
By the way, change state selecting logic a bit. Instead of last sleep
time use short-time average of it. Global interrupts rate in system is a
quite random value, to corellate subsequent sleeps so directly.
sleepable context for net80211 driver callbacks. This removes the need for USB
and firmware based drivers to roll their own code to defer the chip programming
for state changes, scan requests, channel changes and mcast/promisc updates.
When a driver callback completes the hardware state is now guaranteed to have
been updated and is in sync with net80211 layer.
This nukes around 1300 lines of code from the wireless device drivers making
them more readable and less race prone.
The net80211 layer has been updated as follows
- all state/channel changes are serialised on the taskqueue.
- ieee80211_new_state() always queues and can now be called from any context
- scanning runs from a single taskq function and executes to completion. driver
callbacks are synchronous so the channel, phy mode and rx filters are
guaranteed to be set in hardware before probe request frames are
transmitted.
Help and contributions from Sam Leffler.
Reviewed by: sam
- Generate fake channel interrupts even if channel busy with previous
request to let it finish. Without this, dumping requests were just queued
and never processed.
- Drop pre-dump requests queue on dumping. ATA code, working in dumping
(interruptless) mode, unable to handle long request queue. Actually, to get
coherent dump we anyway should do as few unrelated actions as possible.
Yukon from common multicast handling code. Yukon uses hash-based
multicast filtering(big endian form) but GENESIS uses perfect
multicast filtering as well as hash-based one(little endian form).
Due to the differences of multicast filtering there is no much
sense to have a common code.
o Remove sk_setmulti() and introduce sk_rxfilter_yukon(),
sk_rxfilter_yukon() that handles multicast filtering setup.
o Have sk_rxfilter_{yukon, genesis} handle promiscuous mode and
nuke sk_setpromisc(). This simplifies ioctl handler as well as
giving a chance to check validity of Rx control register of
Yukon.
o Don't reinitialize controller when IFF_ALLMULTI flags is changed.
o Nuke sk_gmchash(), it's not needed anymore.
o Always reconfigure Rx control register whenever a new multicast
filtering condition is changed. This fixes multicast filtering
setup on Yukon.
PR: kern/134051
- Probe supported sleep states from acpi_attach() just once and do not
call AcpiGetSleepTypeData() again. It is redundant because
AcpiEnterSleepStatePrep() does it any way.
- Treat UNKNOWN sleep state as NONE, i.e., "do nothing", and remove obscure
NONE state (ACPI_S_STATES_MAX + 1) to avoid confusions.
- Do not set unsupported sleep states as default button/switch events.
If the default sleep state is not supported, just set it as UNKNOWN/NONE.
- Do not allow sleep state change if the system is not fully up and running.
This should prevent entering S5 state multiple times, which causes strange
behaviours later.
- Make sleep states case-insensitive when they are used with sysctl(8).
For example,
sysctl hw.acpi.lid_switch_state=s1
sysctl hw.acpi.sleep_button_state=none
are now legal and equivalent to the uppercase ones.
Feature is controlled by hint.ata.X.pm_level tunable:
0 - PM disabled, old behaviour, default.
1 - device is allowed to initiate PM state change, host is passive.
2 - host initiates PARTIAL state transition every time port is idle.
3 - host initiates SLUMBER state transition every time port is idle.
PARTIAL state has up to 100us (50us for me) wakeup latency, but for my
ICH8M saves 0.5W of power per drive. SLUMBER state has up to 10ms (3.5ms
for me) wakeup latency, but saves 0.8W of power.
Modes 2 and 3 are implemented only for AHCI driver now.
Interface power management is incompatible with device presence detection
(host receives no signal from drive, so unable to monitor it), so later is
disabled when PM is used.
- Add some missing const.
- Move the size of the window spun by the registers to the softc
as neither using va_mem_size for this nor va_mem_base for the
start of the bus addresses is appropriate.
MFC after: 1 week
This change adds (possibly redundant) early check for invalid
state input parameter (including S0). Handling of S5 request
is reduced to simply calling shutdown_nice(). As a result
control flow of acpi_EnterSleepState is somewhat simplified
and resume/backout half of the function is not executed
for S5 (soft poweroff) request and invalid state requests.
Note: it seems that shutdown_nice may act as nop when initproc
is already initialized (to grab pid of 1), but init process is in
"pre-natal" state.
Tested by: Fabian Keil <fk@fabiankeil.de>
Reviewed by: njl, jkim
Approved by: rpaulo
controllers may be configured as legacy IDE mode by modifying subclass and
progif without actually changing PCI device IDs. Instead of complicating
code, we always force AHCI mode while probing. Also we restore AHCI mode
while resuming per ATI/AMD register programming/requirement guides.
- Fix SB700/800 "combined" mode. Unlike SB600, this PATA controller can
combine two SATA ports and emulate one PATA channel as primary or secondary
depending on BIOS configuration. When the combined mode is disabled, this
channel disappears and it works just like SB600 PATA controller, however.
- Add more PCI device IDs for SB700/800 and adjust device descriptions.
SB800 shares the same PCI device IDs and added two more SATA IDs.
this driver to compile and limp along with the new layer. These changes
do not deal with proper locking around access to the HW. This is only
a starting point. I have not tested modem control but tip seems to work
okay and I can send and receive characters which I needed for one of my
-current boxes. I have not tied this driver back up to the build since
I don't want people to think it is ready for prime time. If anyone
else has some cycles to work on this feel free to!
Also add support for a 16 port PCI interface I have at work.
Glanced at by: ed
