Submitted by: Roger Hardiman <roger@cs.strath.ac.uk>
options BROOKTREE_SYSTEM_DEFAULT=BROOKTREE_PAL
in the kernel config file makes the driver's video_open() function
select PAL rather than NTSC. This fixed all the hangs on my
Dual Crystal card when using a PAL video signal.
As a result, you can loose the tsleep (of 2 seconds - now 0.25!!)
which I previously added. (Unless someone else wanted the 0.25
second tsleep).
submitted ioctl to clear the video buffer
prior to starting video capture
Amancio : clean up yuv12 so that it does not
affect rgb capture. Basically, fxtv after
capturing in yuv12 mode , switching to rgb
would cause the video capture to be too bright.
1.32 disable inverse gamma function for rgb and yuv
capture. fixed meteor brightness ioctl it now
converts the brightness value from unsigned to
signed.
1.33 added sysctl: hw.bt848.tuner, hw.bt848.reverse_mute,
hw.bt848.card
card takes a value from 0 to bt848_max_card
tuner takes a value from 0 to bt848_max_tuner
reverse_mute : 0 no effect, 1 reverse tuner
mute function some tuners are wired reversed :(
but doesn't do much of anything with it. I added it to siopnp_ids[]
and it was found and recognized as a serial port.
PR: 6605
Reviewed by: phk
Submitted by: Dave Marquardt <marquard@zilker.net>
[__]inline is only used to bloat the code here. It gives a separate copy
of all the strings for each time this header is included...
Fixed misuse of __P(()).
- pessimized i/o port types.
- other pessimized types.
- Don't use DEBUG (causes LINT warnings). Use DGB_DEBUG instead.
- commented out code.
- cloned code that doesn't apply ("Smarts" is for the cy driver only).
Submitted by: bde
dereference uninitialized pointers.
o Fix DEVFS permissions
o Fix DEVFS minor numbers
o Add initial & lock devices for cua device.
o Fix permissions in line with sio.
This code will be turned on with the TWO options
DEVFS and SLICE. (see LINT)
Two labels PRE_DEVFS_SLICE and POST_DEVFS_SLICE will deliniate these changes.
/dev will be automatically mounted by init (thanks phk)
on bootup. See /sys/dev/slice/slice.4 for more info.
All code should act the same without these options enabled.
Mike Smith, Poul Henning Kamp, Soeren, and a few dozen others
This code does not support the following:
bad144 handling.
Persistance. (My head is still hurting from the last time we discussed this)
ATAPI flopies are not handled by the SLICE code yet.
When this code is running, all major numbers are arbitrary and COULD
be dynamically assigned. (this is not done, for POLA only)
Minor numbers for disk slices ARE arbitray and dynamically assigned.
Submitted by: Roger Hardiman <roger@cs.strath.ac.uk>
Roger Hardiman <roger@cs.strath.ac.uk> :
Revised autodetection code to correctly handle both
old and new VideoLogic Captivator PCI cards.
Added tsleep of 2 seconds to initialistion code for PAL users.
Corrected clock selection code on format change.
--- Amancio
- Set the correct value scp->font_size in init_scp().
- Set scp->font_size to FONT_NONE for VGA_MODEX.
Interim fix for a font problem:
- A kludge to display the correct font on some video cards.
We should be able to load multiple fonts to the VGA plane #2 and switch
between fonts by setting the font select register in the VGA sequencer.
It appears that the current code isn't functioning as expected on
some VGA cards (I have reports on Millenium and Mach64 cards). This is
either a bug in syscons or a hardware compatibility problem ;-<
This kludge will always load only one font set at a time and always use
the font page #0 on the plane #2. It is an interim kludge until
we find the exact cause and solution.
Small adjustment for mouse cursor handling:
- Turn off the mouse cursor early when changing video modes.
Video mode switch fixes:
- Stop the screen saver when changing video modes.
- Enclose the critical section with a pair of spltty()/splx().
- A kludge to prevent scrn_update() from accessing video memory in less-
critical sections in video mode change; artificially turn on the
UNKNOWN_MODE flag.
PR: bin/5899, bin/5907
Tested by: ache and a couple of users
OKed by: sos
* Figure out UTC relative to boottime. Four new functions provide
time relative to boottime.
* move "runtime" into struct proc. This helps fix the calcru()
problem in SMP.
* kill mono_time.
* add timespec{add|sub|cmp} macros to time.h. (XXX: These may change!)
* nanosleep, select & poll takes long sleeps one day at a time
Reviewed by: bde
Tested by: ache and others
- Attempt to handle PCI devices where the interrupt is
an ISA/EISA interrupt according to the mp table.
- Attempt to handle multiple IO APIC pins connected to
the same PCI or ISA/EISA interrupt source. Print a
warning if this happens, since performance is suboptimal.
This workaround is only used for PCI devices.
With these two workarounds, the -SMP kernel is capable of running on
my Asus P/I-P65UP5 motherboard when version 1.4 of the MP table is disabled.
- Implement proper EISA probing.
- Better support for the new transputer based host cards.
- use standard termios settings, one can use the intial/lock devices.
- use a simple bcopy since some cards/systems apparently don't support
32 bit accesses.
- hard reset and halt host card CPU prior to download in case of a soft
restart.
- recognize new remote module types (ASIC vs. CD1400 based)
- a number of cosmetic changes (my fault, not Nick's)
Submitted by: Nick Sayer <nsayer@quack.kfu.com>
Fixed pedantic semantics errors (in ANSI C, static arrays must have
a size, and static objects should be consistently declared as static
unless you know more than anyone should have to know about the
linkage rules).
select/poll and DEVFS changes, which are limited to an include/define
in sound.h and the actual select/poll implementation in sound.c
[ This commit is blind, but the code is similar enough that there will
hopefully be no problems. ]
The differences Terrys patch and this patch are:
* Remove a lot of un-needed comments.
* Don't put l_hotchar at the front of stuct linesw, there is no need to.
* Use the #defines for the hotchar in the SLIP and PPP line disciplines
this using option "-b" to the boot blocks. It is smartest to compile
a font into your kernel (See LINT), but not mandatory, but apart from
the cursor you will see nothing on the screen until you load a font.
This mode allows XF86_VGA16 to run in 800x600 mode on otherwise unsupported
graphics hardware.
A number of buglets in the cursor handling in syscons may become
visible this way.
mode switch in ioctl.
Possibly related to PR: kern/4271
- A kludge: initialize scp->xpixel and ypixel even in the text mode.
If the console enters the `unknown' graphics mode via the ioctl KDSETMODE
(KD_GRAPHICS), these fields are not set (because syscons cannot know
the correct values), but set_mouse_pos() need to refer to these field
to adjust the mouse position.
- Turn off MOUSE_VISIBLE when switching video mode by ioctl.
- another new option: SC_MOUSE_CHAR
Define the first character code of four consecutive codes to be used for
the mouse cursor. Default codes are 0xd0 through 0xd3. Beware that
if you decide to use any codes outside the range of 0xc0-0xdf,
the mouse cursor may not look good, because of the way VGA displays
characters in 9-dot-wide character cells.
Requested by several people.
(This patch was tested by a person who recently reported, in the -current
ML, a page fault problem in the kernel (draw_mouse_iamge()) after
X server shutdown. The patch cured his problem.)
Don't touch/update the screen while manipulating font data.
Possibly related to PR: kern/4271
- Set up VGA in alphanumeric mode rather than graphics mode when
loading font into video memory. This will drastically reduce flicker.
PR: bin/2977
- Set up scp->font_size properly during video mode switch caused by
ioctl.
separate routine: scupdate() called from scrn_timer().
- Make sure that the screen is updated for the low-level console
routines sccngetc() and sccncheckc(). A new routine, sccnupdate(),
is introduced and will call scupdate() above.
Requested by: bde and msmith
OKed by: sos
from the low-level console routines sccngetc() and sccncheckc().
Submitted by: bde (a long time ago)
- Don't try to ring bell and immediately return from do_bell() while
device probe is in progress at boot time; the timeout queue is not
functional yet.
PR: kern/2424
- Stop running the screen saver after panic() is called: check
if `panicstr' is non-NULL during scrn_timer().
PR: kern/5314
- A new option: SC_DISABLE_REBOOT
The reboot key (usually Ctl-Alt-Del) will be ignored if this option
is defined. You may still have the reboot key defined in the keymap and
it won't cause error when the keymap is loaded, but it will be quietly
treated as nop.
OKed by: sos
1. Takeshi Ohashi <ohashi@atohasi.mickey.ai.kyutech.ac.jp> submitted
code to support bktr_read . /usr/src/share/examples/rgb24.c now works 8)
2. Flemming Jacobsen <fj@schizo.dk.tfs.com> submitted code to support
radio available with in some bt848 based cards;additionally, wrote
code to correctly recognized his bt848 card.
3. Roger Hardiman <roger@cs.strath.ac.uk> submitted various fixes to smooth
out the microcode and made all modes consistent.
4. Added supported for yuv12 so we know can capture raw streams and feed it
to mpeg_encoder . The upshot is that we can now mpeg encode more and save
nearly 100 percent of the disk requirements previously for programs such
as fxtv first save the raw video image to disk then converted to a
format suitable for mpeg_encode.
a BSD4.4Lite1 feature, not a FreeBSD feature. <sys/ioctl.h> is a
compatibility misfeature.
Moved NPCI ifdef. This file didn't compile if NPCI <= 0. It shouldn't
be configured in that case, but it is easy to support (mis)configuration
of drivers without buses by generating null objects, and many drivers
do it.
Removed unused includes.
This introduce an xxxFS_BOOT for each of the rootable filesystems.
(Presently not required, but encouraged to allow a smooth move of option *FS
to opt_dontuse.h later.)
LFS is temporarily disabled, and will be re-enabled tomorrow.
so that existing programs which were compiled before the introduction
of the new mouse code and use these ioctls will run unmodified.
Suggested by msmith.
not quite correct, because the Makefiles in lkm/syscons don't set up the
`machine' symlink, but other, more volatile headers in <machine> are
already used.
(accent_key + space does still print the accent letter too, as in
the previous commit.)
Requested by a couple of users.
- Clear the accent flag when the next_screen key is pressed.
- Added some comment lines regarding accent key processing.
This will not make any of object files that LINT create change; there
might be differences with INET disabled, but hardly anything compiled
before without INET anyway. Now the 'obvious' things will give a
proper error if compiled without inet - ipx_ip, ipfw, tcp_debug. The
only thing that _should_ work (but can't be made to compile reasonably
easily) is sppp :-(
This commit move struct arpcom from <netinet/if_ether.h> to
<net/if_arp.h>.
- IIR_TXRDY is never off even if reading a IIR register.
- Know as PIAFS "Palido 321S", "DC-*S" oemed by Sharp corp.
2. Omiting a restrict probing if it's already probed by pccardd.
Note: Define a new id_flags as follows
0x40000 - NO PROBE (Already probed as serial)
0x80000 - Has a bogus IIR_TXRDY register
Sato Junichi <junichi@astec.co.jp>
Nrihiro Kumagai <kuma@slab.tnr.sharp.co.jp>
Hirao Tetsuya <ai.cs.fujitsu.co.jp>
Toshiharu Asai <asai@mbc.infoshere.or.jp>
Shin'ya Kumabuchi <kumabu@t3.rim.or.jp>
Freebsd-users-jp@jp.freebsd.orgbsd-nomads@ai.cs.fujitsu.co.jp
With a keymap with accent key definitions loaded to syscons, you press
an accent key followed by a regular letter key to produce an accented
letter. Press an accent key followed by the space bar to get the
accent letter itself.
Code is based on the ideas and work by jmrueda@diatel.upm.es and
totii@est.is.
PR: i386/4016
console.h
- Defined structures and constants for accent (dead) keys.
syscons.c, kbdtables.h
- When an accent key is pressed, set the corresponding index to
`accents'. If the next key is the space key, produce the accent char
itself. Otherwise search the accent key map entry, indexed by
`accents', for a matching pair of a regular char and an accented char.
- Added ioctl functions to set and get the accent key map (PIO_DEADKEYMAP
and GIO_DEADKEYMAP).
Submitted by: Jonathan Hanna <pangolin@rogers.wave.ca>
The patch is for a Hauppauge Win/TV dbx with FM. I still need to
config OVERRIDE_TUNER, but it works nicely.
necessary to call it when the tty layer's output state has not been
changed, but siostop() sometimes changes the TS_BUSY state and then
calls comstart() mainly for its side effect of calling ttwwakeup().
need to do it directly, since ttwwakeup() is always called just before
returning from rpstart(). The brokenness was waking up the wrong address
after clearing TS_SO_OLOWAT. It's not clear how processes waiting for
output to drain below low water ever got woken up.
Found by: when I fixed longstanding warts in output watermark
handling, this was the only driver that knew too much
(anything) about the watermarks
The #ifdef IPXIP in netipx/ipx_if.h is OK (used from ipx_usrreq.c and
ifconfig.c only).
I also fixed a typo IPXTUNNEL -> IPTUNNEL (and #ifdef'ed out the code
inside, as it never could have compiled - doh.)
MS IntelliMouse, Kensington Thinking Mouse, Genius NetScroll,
Genius NetMouse, Genius NetMouse Pro, ALPS GlidePoint, ASCII
MieMouse, Logitech MouseMan+, FirstMouse+
- The `psm' driver is made to recognize various models of PS/2 mice
and enable their extra features so that their additional buttons and
wheel/roller are recognized. The name of the detected model will be
printed at boot time.
- A set of new ioctl functions are added to the `psm', `mse' and
`sysmouse' drivers so that the userland program (such as the X server)
can query device information and change driver settings.
- The wheel/roller movement is handled as the `Z' axis movement by the
mouse drivers and the moused daemon. The Z axis movement may be mapped
to another axis movement or buttons.
- The mouse drivers support a new, standard mouse data format,
MOUSE_PROTO_SYSMOUSE format which can encode x, y, and x axis movement
and up to 10 buttons.
/sys/i386/include/mouse.h
- Added some fields to `mousestatus_t' to store Z axis movement
and flag bits.
- Added the field `model' to `mousehw_t' to store mouse model code.
Defined model codes.
- Extended `mousemode_t'.
- Added new protocols and some constants for them.
- Added new ioctl functions and structures.
- Removed obsolete ioctl definitions.
/sys/i386/include/console.h
- Added `dz' field to the structure `mouse_data' to pass Z axis movement
to `syscons/sysmouse'.
- Removed LEFT_BUTTON, MIDDLE_BUTTON and RIGHT_BUTTON. Use button bits
defined in `mouse.h' instead.
/sys/i386/isa/psm.c
- Added a set of functions to detect various mice which have additional
features (wheel and buttons) unavailable in the standard PS/2 mouse.
- Refined existing ioctl functions and added new ones. Most important
of all is MOUSE_SETLEVEL which manipulates the output level of the driver.
While the output level remains zero, the output from the `psm' driver is
in the standard PS/2 mouse format (three bytes long). When the level
is set to one, the `psm' driver will send data in the extended format.
At the level two the driver uses the format which is native to the
connected mouse is used. (Meaning that the output from the device is
passed to the caller as is, unmodified.) The `psm' driver will pass
such extended data format as is to the caller if the output level is
two, but emulates the standard format if the output level is zero.
- Added kernel configuration flags to set initial resolution
(PSM_CONFIG_RESOLUTION) and acceleration (PSM_CONFIG_ACCEL).
- Removed the compile options PSM_ACCEL, PSM_CHECKSYNC and PSM_EMULATION.
Acceleration ratio is now specified by the kernel configuration flags
stated above. Sync check logic is refined and now standard.
The sync check can be turned off by the new kernel configuration flags
PSM_CONFIG_NOCHECKSYNC (0x100). PSM_EMULATION has been of little use.
- Summer clean up :-) Removed unused code and obsolete comments.
/sys/i386/isa/mse.c
- Created mseioctl() to deal with ioctl functions MOUSE_XXXX.
Most importantly, the MOUSE_SETLEVEL ioctl will change the
output format from the 5 byte format to the new, extended format
so that the caller can take advantage of Z axis movement and additional
buttons.
- Use constants defined in `mouse.h' rather than magic numbers.
/sys/i386/isa/syscons.c
- Changed scioctl() to reflect the new `console.h' and some of the new
ioctls defined in `mouse.h'. Most importantly, the MOUSE_SETLEVEL
ioctl will change the `sysmouse' output format from the MouseSystems
5 byte format to the new, extended format so that the caller can
take advantage of Z axis movement and additional buttons.
- Added support for double/triple click actions of the left button and
single click action of the right button in the virtual console. The
left button double click will select a word under the mouse pointer.
The triple click will select a line and the single click of the right
button will extend the selected region to the current position of
the mouse pointer. This will make the cut/paste support more compatible
with xterm.
/sys/i386/isa/kbdio.h
- Added PSM_INTELLI_ID.
checking the BIOS video mode paramter table. Now syscons uses the
parameter table even if some bits in the table are different from the
current VGA register settings.
Even if comp_vgaregs() finds that the BIOS video parameter table looks
totally unfamiliar to it, syscons allows the user to change the
current video mode to some modes which are based on the VGA 80x25
mode. They are VGA 80x30, VGA 80x50, VGA 80x60. In this case the user
will be warned, during boot, that video mode switching is only
paritally supported on his machine.
PR: bin/4477
Fixed nonblocking mode. It was per-device instead of per-file.
Don't depend on gcc's misfeature of rewriting char args in old-style
function definitions to match wrong prototypes. Break K&R1 support
to fix this quickly.
actually offsets, they are offsets scaled by dividing by 2^cy_align.
I use different values for cy_align since the -current values are
unnaturally scaled, so I need different offsets, and the wrong
offsets got committed.
Reported by: nnd@itfs.nsk.su (N.Dudorov)
2) Fix temporal decimation, disable it when
doing CAP_SINGLEs, and in dual-field capture, don't
capture fields for different frames
Submitted by: Luigi Rizzo & Randall Hopper
changes:
o rip the old select from his distribution to prevent extra pollution
o the code now uses audio dma, helps reduce clicks
o improved card support, should work in full duplex on sb16 cards
o add better voxware ioctl support pointed out by Joao Carlos Mendes
Luis <jonny@coppe.ufrj.br>
o remove an unused file that I included for more complete history
o and MANY other changes
I have personally tested this code with a CS4237 based card and an AWE32
(non-PnP). Both cards worked fine in 8bit and 16bit mode.
This make the Miro PCTV work for me, including audio, and should
hopefully fix the other audio problems some people have been having.
Reviewed by: ahasty & Luigi Rizzo (freebsd-multimedia)
to define it by including <sys/kernel.h>. That broke PC-CARD
support for this driver, producing the dreaded "device allocation
failed" message. Surprisingly, the missing include caused only
two compiler warnings. The compilation still "succeeded" anyway.
usage at 0x100. Quoted Justin's quotation from the manual as well, to
explain the technical background.
PR: kern/4559
Submitted by: Stephen J. Roznowski <sjr@home.net>
use a Linker Set. Note, if a driver is loaded as an LKM if will have
to use the function call, but since none of the existing drivers
are loadable, this made things cleaner and boot messages nicer.
Obtained from: PAO-970616
flicker won't occur when set_border() is called.
- Properly restore the border color when switching virtual consoles.
Pointed out by: tony@dell.com
OKed by: sos
screen size was changed while the screen saver was inactive. Adjust
the positions of the daemon and the text and clip them accordingly
each time.
- Don't call set_border() too often. Some video chip may produce
flicker.
Pointed out by tony@dell.com
- Don't fill the entire screen with blank char every time the saver is
called. Blank only the part of the screen where the daemon and the
text was previously printed.
* Kill individual drivers 'suspend' routines, since there's no simple/safe
way to suspend/resume a card w/out going through the complete probe
at initialization time.
* Default to using the apm_pccard_resume sysctl code, which basically
pretends the card was removed, and then re-inserted. Suspend/resume
is now 'emulated' with a fake insert/removal. (Hence we no longer
need the driver-specific suspend routines.)
follow.
* Rename/reorder all of the pccard structures, change many of the member
names to be descriptive, and follow more closely other 'bus' drivers
naming schemes.
* Rename a bunch of parameter and local variable names to be more
consistant in the code.
* Renamed the PCCARD 'crd' device to be the 'card' device
* KNF and make the code consistant where it was obvious.
* ifdef'd out some unused code
check the value and caused kernel panic when a large value was given.
- Move the configuration option SC_HISTORY_SIZE from syscons.h to
syscons.c.
- Define the maximum total number of history lines of all consoles.
It is SC_HISTORY_SIZE*MAXCONS or 1000*MAXCONS; whichever is larger.
CONS_HISTORY will allow the user to set the history size up to
SC_HISTORY_SIZE unconditionally (or the current height of the console
if it is larger than SC_HISTORY_SIZE). If the user requests a larger
buffer, it will be granted only if the total number of all allocated
history lines and the requested number of lines won't exceed the maximum.
- Don't free the previous history buffer and leave the history buffer
pointer holding a invalid pointer. Set the pointer to NULL first, then
free the buffer.
PR: bin/4592
floppy drive #0, regardless of what the CMOS says. This is intended
as a bandaid for those plagued with Compaq's idea to not announce the
floppy drive on their `Aero' notebook.
Using the device flags is not very nice (in particular since they
aren't per-drive but per-controller), but still looks a lot better to
me than the disgusting guesswork hack that was recently posted to
-hackers.
Doc update will follow shortly.
a change that might have an effect on the problems some have seen
with older chips, it looks like the driver may have mistakenly thought
there was an SIA when there isn't.
Distribute all but the most fundamental malloc types. This time I also
remembered the trick to making things static: Put "static" in front of
them.
A couple of finer points by: bde
This driver includes the following patches submitted by:
1.0 Hideyuki Suzuki <hideyuki@sat.t.u-tokyo.ac.jp>
Japanese Cable support
2.0 Keith Sklower <sklower@CS.Berkeley.EDU>
Minor update to the BSDI section so it compiles cleanly on BSDI
3.0 Joao Carlos Mendes Luis <jonny@coppe.ufrj.br>
ioctl interface to select video format , NTSC, PAL, etc...
savers are also modified so that they behave in the same way as the
blank saver on MDA and CGA, although it's not the way these screen
savers are supposed to work, but fading monitor and tickling green
monitor cannot be done on MDA and CGA, AFAIK. So, this is the second
best solution.
As of this change, the current state of support of screen savers is
summarized in the following table.
MDA CGA EGA VGA
blank OK OK NA OK
daemon OK OK OK OK
fade * * NA OK
green * * NA OK
snake OK OK OK OK
star OK OK OK OK
OK: works
NA: doesn't work, the module cannot be loaded for this adapter.
*: behave the same way as the blank saver.
As you can see, EGA is left out for now. But, we can do no better, as
EGA registers cannot be read...
Reviewed by: sos
shown to be harmful in that it results in the card not being detected
properly on warmboot due to the station address failing to be read
correctly from the NVRAM.
much like the scancode mode.
However the keys that (for no good reason) returns extension codes
etc, are translated into singlebyte codes.
Needed by libvgl. This makes life ALOT easier, also the XFree86
folks could use this.
overruns (not that it was a problem, but it could be):
1) Doubled the number of receive buffers in the DMA chain to 64.
2) Do packet receive processing before transmit in the interrupt routine.
if it is in 10Mbps mode and gets certain types of garbage prior to
the packet header. The work-around involves reprogramming the
multicast filter if nothing is received in some number of seconds
(currently set at 15). As a side effect, implemented complete support
for multicasting rather than the previous 'receive all multicasts'
hack, since we now have the ability to program the filter table.
Fixed a serious bug which crept in with the timeout() changes;
the cookie was only saved on the first timeout() call in fxp_init()
and wasn't updated in the most common place in fxp_stats_update()
when the timeout was rescheduled. This bug would have resulted in
an eventual panic if fxp_stop() was called (which happens when any
interface flags are changed, for example).
Fixed a bug in Alpha support that would have caused the TxCB
descriptor chain to span a page boundry, causing serious problems
if the pages didn't happen to be contiguous.
Removed some gratuitous bit masking that was left over from an
older implementation.
Fixed a bug where too much was copied from the configuration
template, spilling over into memory that followed it.
Fixed handling of if_timer...it was cleared too early in some cases.
operands that are set during seqeuncer program download instead of at
assembly time.
Convert the sequencer code to use" downloaded constants" for four run time
constants that vary depending on the board type. This frees up 4 bytes
of sequencer scratch ram space where these constants used to be stored and
also removes the additional instructions required to load their values
into the accumulator prior to using them.
Remove the REJBYTE sram variable. The host driver can just as easly
read the accumulator to get this value.
The scratch ram savings is important as the old code used to clober the
SCSICONF register on 274X cards which sits near the top of scratch ram
space. The SCSICONF register controls bus termination, and clobbering
it is not a good thing. Now we have 4 bytes to spare.
This should fix the reported problems with cards that don't have devices
attached to them failing with a stream of "Somone reset bus X" messages.
Doug Ledford determined the cause of the problem, fixes by me.
1. Clustered I/O is switched by the MNT_NOCLUSTERR and MNT_NOCLUSTERW
bits of the mnt_flag. The sysctl variables, vfs.foo.doclusterread
and vfs.foo.doclusterwrite are deleted. Only mount option can
control clustered I/O from userland.
2. When foofs_mount mounts block device, foofs_mount checks D_CLUSTERR
and D_CLUSTERW bits of the d_flags member in the block device switch
table. If D_NOCLUSTERR / D_NOCLUSTERW are set, MNT_NOCLUSTERR /
MNT_NOCLUSTERW bits will be set. In this case, MNT_NOCLUSTERR and
MNT_NOCLUSTERW cannot be cleared from userland.
3. Vnode driver disables both clustered read and write.
4. Union filesystem disables clutered write.
Reviewed by: bde
- some addition of comments (for readability)
- iso-2022 G0 designation support. This does almost nothing. Just for
avoiding garbled screen when got "ESC ( B".
(how about G1/2/3 designation? I'm not sure)
the normal CS4326 except that it's had it's ID's tweaked for some reason)
Also mark the device as alive in the attach routine so that the pnp system
doesn't think the attach failed.
of multiple PCI IDE controllers(Dyson), and some updates and cleanups from
John Hood, who originally made our IDE DMA stuff work :-).
I have run tests with 7 IDE drives connected to my system, all in DMA
mode, with no errors. Modulo any bugs, this stuff makes IDE look
really good (within it's limitations.)
Submitted by: John Hood <cgull@smoke.marlboro.vt.us>
rather than extracting the diff from Mark's patch, but it turns out that
I was freeing one allocation twice due to a previous cut/paste braino.
My botch, not Mark's.
Pointed out by: Mark Valentine <mv@pobox.com>
internal modems. Currently detects a USR modem, and a couple Supra
modems... vendor id's for sio capabile cards welcomed...
document new option EXTRA_SIO that will increase sio's internal data
structures to support X more serial ports... these are used by the
PnP part of sio for attaching... If you don't have it specified, it
will default to 2... This is defaulted to 0 if you don't have PnP
compiled into your kernel...
also document that if you set the PnP flags (pnp x flags y) to 0x1 that
the modem will be refused to be recognized by the sio driver... this
is for people that want the traditional isa driver to probe and attach
the modem... (for keeping legacy sio numbering)
number of dma overruns/underruns for systems under heavy dma load.
As a side effect, broken enhanced floppy controllers that sometimes
don't detect dma overruns/underruns will give less errors.
Reviewed by: j@uriah.heep.sax.de (J Wunsch)
Hide the bogus FDC ``chip type'' display behind a (mostly) undocumented
option, since people started to trust the bogus claim. Once we're going
to handle 2.88 MB controllers, we have to redo the chip detection, by
now just leave it hidden.
large (over 4KB) softc struct. The descriptor array is accessed by
busmaster dma and must be physically contiguous in memory. malloc() of
a block greater than a page is only virtually contiguous, and not
necessarily physically contigious.
contigmalloc() could do this, but that is a bit on the overkill side.
I'm not sure of the origins of the problem report and diagnosis, I learned
of the problem via mail forwarded from Jim Shankland <jas@flyingfox.com>.
Jim said that Matt Thomas's workaround was to reduce the number of
transmit descriptors from 128 to 32, but I was concerned that it might
cost performance. Anyway, this change is my fault, not Jim's. :-)
Reviewed by: davidg
delay that without this the performance is unacceptable. The 83C690,
83C790, and 83C795 chips which this affects are all designed to work
with 0 waitstates in 16bit mode.
Also cleaned up the toggling of 16bit access mode that occurs during
normal operation; the previous code may not have done the right thing
in all cases.
size in terms of lines (instead of bytes). When changing video mode
in ioctl SW_XXX commands, syscons checks scp->history_size and
allocate a history buffer at least as large as the new screen size.
(This was unnecessary before, because HISTORY_SIZE was as large as 100
lines and this is bigger than the maximum screen size: 60 lines).
Similar adjustment is done in ioctl CONS_HISTORY command too.
PR: kern/4169
Reviewed by: sos
Includers of this file apparently didn't know that <sys/queue.h>
was a prerequisite and include a semi-random collection headers
until one happened to include it.
and hardware.
There is now another simple_lock around clock data/hardware accesses in
clock.c and microtime.s. It is my belief that this is the only area
sio/cy might stumble into during an unblocked INTerrupt. Thus I separated
the sio/cy code from the generic disable_intr()/enable_intr() routines.
Controlled by smptests.h: USE_COMLOCK, ON by default.
Add a simplelock to deal with disable_intr()/enable_intr() as used in UP kernel.
UP kernel expects that this is enough to guarantee exclusive access to
regions of code bracketed by these 2 functions.
Add a simplelock to bracket clock accesses in clock.c: clock_lock.
Help from: Bruce Evans <bde@zeta.org.au>
Remove unused headers.
Remove all but one instance of the device base name.
Prototype some local static functions.
Consistently reference the softc structure as "sc" rather than "lpt".
Prompted-by: bde
arg of type u_short (just write the function in ANSI C like most
other functions in this file instead of fixing the interface or
depending on a gcc feature).
